When CONFIG_SERIAL_PXA_CONSOLE is disabled, the serial_pxa_get_poll_char
and serial_pxa_put_poll_char functions are not defined, and we can't
reference them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In (efe2f29 kgdboc,kdb: Allow kdb to work on a non open console port)
support was added to directly use the "write_char" functions when
doing kdb over a non-open console port. This is great, but it ends up
bypassing the normal code in uart_console_write() that adds a carriage
return before any newlines.
There appears to have been a trend to add this support directly in
some console driver's poll_put_char() functions. This had a few side
effects, including:
- In this case we were doing LFCR, not CRLF. This was fixed in
uart_console_write() back in (d358788 [SERIAL] kernel console should
send CRLF not LFCR)
- Not all serial drivers had the LFCR code in their poll_put_char()
functions. In my case I was running serial/samsung.c which lacked
it.
I've moved the handling to uart_poll_put_char() to fix the above
problems. Now when I use kdb (and don't point console= to the same
UART) I no longer get:
[0]kdb>
[0]kdb>
[0]kdb>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/tty/serial/pxa.c:793:17: warning: symbol 'serial_pxa_pops' was not declared. Should it be static?
drivers/tty/serial/pxa.c:971:12: warning: symbol 'serial_pxa_init' was not declared. Should it be static?
drivers/tty/serial/pxa.c:986:13: warning: symbol 'serial_pxa_exit' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This #if-0'd block wouldn't compile, so let's dispose it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write() function could be used by printk(), which is atomic and
tweaking clock there can cause "BUG: sleeping function called from
invalid context".
Signed-off-by: Bao Haojun <hjbao@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually, in order to support KGDB over serial console one must
implement two callbacks for character polling. Clone them from
8250 driver with a bit of tuning.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Marko Katic <dromede@gmail.com>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: Russell King <linux@arm.linux.org.uk>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
drivers/tty/serial/pxa.c | 55 ++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 55 insertions(+), 0 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
v3:
Remove empty line
v2:
Move local_irq_save() after clk_prepare_enable()
v1:
At UP mode, when cpu want to print message in kernel, it will invoke
peempt_disable and disable irq. So it is safe for UP mode.
For SMP mode, it is not safe to protect the HW reigsters.
one CPU will run a program which will invoke printf.
another CPU will run a program in kernel that invoke printk.
So when second CPU is trying to printk, it will do
1. save ier register
2. enable uue bit of ier register
3. push buffer to uart fifo
4 .restore ier register
when first CPU want to printf, and it happens between 1 and 4, it will
enable thre bit of ier, and waiting for transmit intterupt. while step 4
will make the ier lost thre bit.
add spin lock here to protect the ier register for console write.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAT24/a2CrR//JCVInAQKYdxAAn+fs7yv+P4OWG/nIhGdnPw8MQ2u9fvqA
pmNL3Jy0eVowbENDcRRZgfhZ3ZlWBGUYym7J1uiFSrmHyJPoMtMvVg0miPYxLlpE
vr8bzuSfGOUOa7+Fk6kFVGxS3ZHZTsDvuhMQUIt/2jHgOaesqPvZ1FYFAj1bZ1fm
2CnQoF3OfnWAngHtoBXtgJxp/1r7+pHlGVbPYpmtHtikl45NmhqWza58aSQBilr+
S90cVeZs91gyveoxz5N+YrO8+Dx05te3mF+dwWuKC6aDC6d76fjLak54AvYv2Pzr
I6iaQPV8GIsXi5R4wptmVQAc5mbk5oktxJ7hCIHrmaBiAXygoVAYoqcuumoO3QDb
QKz10ga1yBYcKYrKvBzKxQrChw53IPU6po+Dd66ALJvLlc3KONksiJs5T/5Wma7P
v3VPcmZwPrJQbz+fQu6FysHeYQY+wfiR5E9Yz2OXs+PtkSy9OYsFFirdhJeWUPgA
ASjNLs1y5rxqrJBt7cjyQiBbIf1awGWyzF0yUNrlYHxmhJ6vcxHfrGoW38VRRCTM
8+JcxOHPRYrPfY7we6zsOn7ZeTWJduoUEeTxDnVS3w3zUIKCvkvkpHaJDvHvYcui
T/yJnXdUD2O3E5+5k/5cCyde8RbSB9gKsNpIMNkK5BLSmbux3C72dE0sMQFysahI
hS8aDCDUQUU=
=fMC+
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
This patch adds clk_prepare/clk_unprepare calls to the serial/pxa
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Errata E20: UART: Character Timeout interrupt remains set under certain
software conditions.
Implication: The software servicing the UART can be trapped in an infinite loop.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnd Bergmann
Peter Hurley
Doug Anderson
Jingoo Han
Daniel Mack
Yi Zhang
Haojun Bao
Jiri Slaby
Denis V. Lunev
Chao Xie
Linus Torvalds
Philipp Zabel
Haojian Zhuang
Marcus Folkesson
Joe Perches
Jovi Zhang
Greg Kroah-Hartman