Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i2c/busses/i2c-s3c2410.c: In function 'i2c_s3c_irq_nextbyte':
drivers/i2c/busses/i2c-s3c2410.c:431:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (i2c->state == STATE_READ)
^
drivers/i2c/busses/i2c-s3c2410.c:439:2: note: here
case STATE_WRITE:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels]
Fixes: 0ef6f3213d ("i2c: at91: add support for new alternative command mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a040 ("i2c: at91: add new driver")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use SMBUS_MASTER_DATA_READ.MASTER_RD_STATUS bit to check for RX
FIFO empty condition because SMBUS_MASTER_FIFO_CONTROL.MASTER_RX_PKT_COUNT
is not updated for read >= 64 bytes. This fixes the issue when trying to
read from the I2C slave more than 63 bytes.
Fixes: c24b8d574b ("i2c: iproc: Extend I2C read up to 255 bytes")
Cc: stable@kernel.org
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some files got renamed but probably due to some merge conflicts,
a few references still point to the old locations.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull i2c updates from Wolfram Sang:
"New stuff from the I2C world:
- in the core, getting irqs from ACPI is now similar to OF
- new driver for MediaTek MT7621/7628/7688 SoCs
- bcm2835, i801, and tegra drivers got some more attention
- GPIO API cleanups
- cleanups in the core headers
- lots of usual driver updates"
* 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits)
i2c: mt7621: Fix platform_no_drv_owner.cocci warnings
i2c: cpm: remove casting dma_alloc
dt-bindings: i2c: sun6i-p2wi: Fix the binding example
dt-bindings: i2c: mv64xxx: Fix the example compatible
i2c: i801: Documentation update
i2c: i801: Add support for Intel Tiger Lake
i2c: i801: Fix PCI ID sorting
dt-bindings: i2c-stm32: document optional dmas
i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support
i2c: core: Tidy up handling of init_irq
i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq
i2c: core: Move ACPI IRQ handling to probe time
i2c: acpi: Factor out getting the IRQ from ACPI
i2c: acpi: Use available IRQ helper functions
i2c: core: Allow whole core to use i2c_dev_irq_from_resources
eeprom: at24: modify a comment referring to platform data
dt-bindings: i2c: omap: Add new compatible for J721E SoCs
dt-bindings: i2c: mv64xxx: Add YAML schemas
dt-bindings: i2c: sun6i-p2wi: Add YAML schemas
i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SMBUS PCI ID for Intel Tiger Lake -LP.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I managed to break sorting in PCI ID defines in my last two patches:
commit 5cd1c56c42 ("i2c: i801: Add support for Intel Comet Lake")
commit 9be1485acc ("i2c: i801: Add support for Intel Elkhart Lake")
Fix them up.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the support of I2C_SMBUS_I2C_BLOCK_DATA transaction type
for the stm32f7 SMBUS Controller.
Use emulated I2C_SMBUS_I2C_BLOCK_DATA transactions as there is no specific
hardware in STM32 I2C to manage this (e.g. like no need for PEC here).
Emulated transfer will fall back calling i2c transfer method where there's
already support for DMAs for example.
So, use the I2C_FUNC_SMBUS_I2C_BLOCK in stm32f7_i2c_func(), and rely on
emulated transfer by returning -EOPNOTSUPP in the smbus_xfer() routine
for such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only set init_irq during i2c_device_new and only handle client->irq on
the probe/remove paths.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It makes sense to contain all the ACPI IRQ handling in a single helper
function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bring the ACPI path in sync with the device tree path and handle all the
IRQ fetching at probe time. This leaves the only IRQ handling at device
registration time being that which is passed directly through the board
info as either a resource or an actual IRQ number.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for future refactoring factor out the fetch of the IRQ
into its own helper function. Whilst we are at it update the handling
to return the actual error code returned from acpi_dev_get_resources
as well.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the available IRQ helper functions, most of the functions have
additional helpful side affects like configuring the trigger type of the
IRQ.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the static from i2c_dev_irq_from _resources so that other parts
of the core code can use this helper function.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I realize that there are changes in drivers/i2c/busses/i2c-i801.c that strictly
speaking don't belong here, but I hope you don't mind. These changes are all
about the interaction with the i2c-mux-gpio code, and I did a test-merge a few
days ago w/o conflicts.
Anyway, the GPIO-work from Linus Walleij (with help from Serge Semin) in the
i2c-mux-gpio and i2c-arb-gpio-challenge drivers is the main feature.
This patch adds a driver for the I2C controller found on the MediaTek
MT7621/7628/7688 SoC's. The base version of this driver was done by
Steven Liu (according to the copyright and MODULE_AUTHOR lines). It
can be found in the OpenWRT repositories (v4.14 at the time I looked).
The base driver had many issues, which are disccussed here:
https://en.forum.labs.mediatek.com/t/openwrt-15-05-loads-non-working-i2c-kernel-module-for-mt7688/1286/3
>From this link an enhanced driver version (complete rewrite, mayor
changes: support clock stretching, repeated start, ACK handling and
unlimited message length) from Jan Breuer can be found here:
https://gist.github.com/j123b567/9b555b635c2b4069d716b24198546954
This patch now adds this enhanced I2C driver to mainline.
Changes by Stefan Roese for upstreaming:
- Add devicetree bindings
- checkpatch clean
- Use module_platform_driver()
- Minor cosmetic enhancements
- Removed IO warpped functions
- Use readl_relaxed_poll_timeout() and drop poll_down_timeout()
- Removed superfluous barrier() in mtk_i2c_reset()
- Use i2c_8bit_addr_from_msg()
- Added I2C_FUNC_PROTOCOL_MANGLING
- Removed adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We are using sysfs functions directly, so we should include the header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe function fails to recognize that upstream clock actually
doesn't yet exist because clock driver has not been initialized.
Actually try to go get the clock and test for its existence
before trying to set up a downstream clock based upon it.
This fixes a bug that causes the i2c driver not to work with
monolithic kernels.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If any of the clock code in the probe fails and returns, the IRQ
will not be freed. Moving the IRQ request to last allows it to
be freed on any errors further up in the probe function. devm_
calls can apparently not be used because there are some potential
race conditions that will arise.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nobody (including me) noticed that these functions were exported but not
added to the header :/
Fixes: 7159dbdae3 ("i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver_find_device() accepts a match function pointer to
filter the devices for lookup, similar to bus/class_find_device().
However, there is a minor difference in the prototype for the
match parameter for driver_find_device() with the now unified
version accepted by {bus/class}_find_device(), where it doesn't
accept a "const" qualifier for the data argument. This prevents
us from reusing the generic match functions for driver_find_device().
For this reason, change the prototype of the driver_find_device() to
make the "match" parameter in line with {bus/class}_find_device()
and adjust its callers to use the const qualifier. Also, we could
now promote the "data" parameter to const as we pass it down
as a const parameter to the match functions.
Cc: Corey Minyard <minyard@acm.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are using sysfs functions directly, so we should include the header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
This switches the i801 GPIO mux to use GPIO descriptors for
handling the GPIO lines. The previous hack which was reaching
inside the GPIO chips etc cannot live on. We pass descriptors
along with the GPIO mux device at creation instead.
The GPIO mux was only used by way of platform data with a
platform device from one place in the kernel: the i801 i2c bus
driver. Let's just associate the GPIO descriptor table with
the actual device like everyone else and dynamically create
a descriptor table passed along with the GPIO i2c mux.
This enables simplification of the GPIO i2c mux driver to
use only the descriptor API and the OF probe path gets
simplified in the process.
The i801 driver was registering the GPIO i2c mux with
PLATFORM_DEVID_AUTO which would make it hard to predict the
device name and assign the descriptor table properly, but
this seems to be a mistake to begin with: all of the
GPIO mux devices are hardcoded to look up GPIO lines from
the "gpio_ich" GPIO chip. If there are more than one mux,
there is certainly more than one gpio chip as well, and
then we have more serious problems. Switch to
PLATFORM_DEVID_NONE instead. There can be only one.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[Removed a newline, suggested by Andy. /Peter]
Signed-off-by: Peter Rosin <peda@axentia.se>
The usage of BUG() macro is generally discouraged in kernel, unless
it's a problem that results in a physical damage or loss of data.
This patch removes unnecessary BUG() macros and replaces the rest
with warning.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Elkhart Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During probe, return the "get_irq" error value instead of -EINVAL which
allows the driver to be deferred probed if needed.
Fix also the case where of_irq_get() returns a negative value.
Note :
On failure of_irq_get() returns 0 or a negative value while
platform_get_irq() returns a negative value.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.146070292@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.720704315@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a match table to allow automatic probing of ACPI device
QCOM0220. Ignore clock attainment errors. Set default clock
frequency value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Qualcomm Geni I2C driver currently probes silently which can be
confusing when debugging potential issues. Add a low level (INFO)
print when each I2C controller is successfully initially set-up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Post suspend I2C registers have power on reset values. Before any
transfer initialize I2C registers to prevent I2C transfer timeout
and implement suspend and resume callbacks needed. Fix below errors
post suspend:
1) Tegra I2C transfer timeout during jetson tx2 resume:
[ 27.520613] pca953x 1-0074: calling pca953x_resume+0x0/0x1b0 @ 2939, parent: i2c-1
[ 27.633623] tegra-i2c 3160000.i2c: i2c transfer timed out
[ 27.639162] pca953x 1-0074: Unable to sync registers 0x3-0x5. -110
[ 27.645336] pca953x 1-0074: Failed to sync GPIO dir registers: -110
[ 27.651596] PM: dpm_run_callback(): pca953x_resume+0x0/0x1b0 returns -110
[ 27.658375] pca953x 1-0074: pca953x_resume+0x0/0x1b0 returned -110 after 127152 usecs
[ 27.666194] PM: Device 1-0074 failed to resume: error -110
2) Tegra I2C transfer timeout error on jetson Xavier post resume.
Remove i2c bus lock-unlock calls in resume callback as i2c_mark_adapter_*
(suspended-resumed) help ensure i2c core calls from client are not
executed before i2c-tegra resume.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-ocore driver already has a polling mode interface.But it needs
a workaround for FU540 Chipset on HiFive unleashed board (RevA00).
There is an erratum in FU540 chip that prevents interrupt driven i2c
transfers from working, and also the I2C controller's interrupt bit
cannot be cleared if set, due to this the existing i2c polling mode
interface added in mainline earlier doesn't work, and CPU stall's
infinitely, when-ever i2c transfer is initiated.
Ref:
commit dd7dbf0eb0 ("i2c: ocores: refactor setup for polling")
The workaround / fix under OCORES_FLAG_BROKEN_IRQ is particularly for
FU540-COOO SoC.
The polling function identifies a SiFive device based on the device node
and enables the workaround.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update device id table for Opencore's I2C master based re-implementation
used in FU540-c000 chipset on HiFive Unleashed platform.
Device ID's include Sifive, soc-specific device for chip specific tweaks
and sifive IP block specific device for generic programming model.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver defers probe because of a missing clock, avoid outputting
an error message. The clock will show up eventually.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit
19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
introduced a new check in order to enumerate some slave devices on Dell
machines. Though, it brings a regression on machines where DMI vendor is not set.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 8 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc4-next-20190613+ #317
RIP: 0010:strcmp+0xc/0x20
To fix this crash, check if vendor field is present before accessing to it.
Fixes: 19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IOP3xx has some elaborate code to directly slam the
GPIO lines multiplexed with I2C down low before enablement,
apparently a workaround for a hardware bug found in the
early chips.
After consulting the developer documentation for IOP80321
and IOP80331 I can clearly see that this may be useful for
IOP80321 family (mach-iop32x) but it is highly dubious for
any 80331 series or later chip: in these chips the lines
are not multiplexed for UARTs.
We convert the code to pass optional GPIO descriptors
and register these only on the 80321-based boards where
it makes sense, optionally obtain them in the driver and
use the gpiod_set_raw_value() to ascertain the line gets
driven low when needed.
The GPIO driver does not give the GPIO chip a reasonable
label so the patch also adds that so that these machine
descriptor tables can be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Gustavo A. R. Silva
Michał Mirosław
Rayagonda Kokatanur
Mauro Carvalho Chehab
Linus Torvalds
YueHaibing
Vasyl Gomonovych
Jarkko Nikula
Fabrice Gasnier
Charles Keepax
Wolfram Sang
Stefan Roese
Wolfram Sang
Annaliese McDermond
Suzuki K Poulose
David S. Miller
Linus Walleij
Bitan Biswas
Alexander Sverdlin
Andy Shevchenko
Thomas Gleixner
Lee Jones
Sagar Shrikant Kadam
Thierry Reding