The Octal DTR configuration is stored in the CFR5V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. Since the next byte address does not contain any
register, it is safe to write any value to it. Write a 0 to it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-3-p.yadav@ti.com
s25fl256s0 does not define the SFDP tables nor implements the
RDSFDP 0x5a command. Skip the SFDP parsing in order to avoid
issuing an unsupported command to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-13-tudor.ambarus@microchip.com
Clarify for what the flash_info flags are used for. Split them in
four categories and a bool:
1/ FLAGS: flags that indicate support that is not defined by the JESD216
standard in its SFDP tables.
2/ NO_SFDP_FLAGS: these flags are used when the flash does not define the
SFDP tables. These flags indicate support that can be discovered via
SFDP. Used together with SPI_NOR_SKIP_SFDP flag.
3/ FIXUP_FLAGS: flags that indicate support that can be discovered
via SFDP ideally, but can not be discovered for this particular flash
because the SFDP table that indicates this support is not defined by
the flash. In case the table for this support is defined but has wrong
values, one should instead use a post_sfdp() hook to set the SNOR_F
equivalent flag.
4/ MFR_FLAGS: manufacturer private flags. Used in the manufacturer
fixup hooks to differentiate support between flashes of the same
manufacturer.
5/ PARSE_SFDP: sets info->parse_sfdp to true. All flash_info entries
that support SFDP should be converted to set info->parse_sfdp to true.
SPI NOR flashes that statically declare one of the
SPI_NOR_{DUAL, QUAD, OCTAL, OCTAL_DTR}_READ flags and do not support
the RDSFDP command are gratuiously receiving the RDSFDP command
in the attempt of parsing the SFDP tables. It is not desirable to issue
commands that are not supported, so introduce PARSE_SFDP to help on this
situation.
New flash additions/updates should be declared/updated to use either
PARSE_SFDP or SPI_NOR_SKIP_SFDP. Once all the flash_info entries are
converted to use SPI_NOR_SKIP_SFDP or PARSE_SFDP, we can get rid of the
SPI_NOR_SKIP_SFDP flag and use just the bool nor->info->parse_sfdp to
determine whether to parse SFDP or not. SPI_NOR_SKIP_SFDP flag is kept
just as a way to differentiate whether a flash is converted to the new
flags logic or not.
Support that can be discovered when parsing SFDP should not be duplicated
by explicit flags at flash declaration. All the flash parameters will be
discovered when parsing SFDP. Sometimes manufacturers wrongly define some
fields in the SFDP tables. If that's the case, SFDP data can be amended
with the fixups() hooks. It is not common, but if the SFDP tables are
entirely wrong, and it does not worth the hassle to tweak the SFDP
parameters by using the fixups hooks, or if the flash does not define the
SFDP tables at all, then statically init the flash with the
SPI_NOR_SKIP_SFDP flag and specify the rest of flash capabilities with
the flash info flags.
With time, we want to convert all flashes to use PARSE_SFDP and
stop triggering the SFDP parsing with the
SPI_NOR_{DUAL, QUAD, OCTAL*}_READ flags. Getting rid of the
SPI_NOR_{OCTAL, OCTAL_DTR}_READ trigger is easily achievable,
the rest are a long term goal.
Manufacturer specific flags like USE_CLSR, USE_FSR, SPI_NOR_XSR_RDY,
will be removed in a future series.
No functional changes intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-7-tudor.ambarus@microchip.com
spansion_post_sfdp_fixups() was called regardless if the flash defined
SFDP tables or not. A better place for this kind of parameters init is
in manufacturer's late_init() hook. post_sfdp() should be called only
when SFDP is defined. No functional change in this patch.
Instead of doing the 4b opcodes settings at manufacturer level, thus
also for every flash that will be introduced, this should be done
just where it is needed, per flash. I'll let this for other patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-12-tudor.ambarus@microchip.com
spi_nor_parse_sfdp(nor, nor->params);
passes for the second argument a member within the first argument.
Drop the second argument and obtain it directly from the first,
and do it across all the children functions. This is a follow up for
'commit 69a8eed58c ("mtd: spi-nor: Don't copy self-pointing struct around")'
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210306095002.22983-4-tudor.ambarus@microchip.com
The S28 flash family uses 2-bit ECC by default with each ECC block being
16 bytes. Under this scheme multi-pass programming to an ECC block is
not allowed. Set the writesize to make sure multi-pass programming is
not attempted on the flash.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-4-p.yadav@ti.com
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Cypress cy15b104q and cy15v104q are 4Mbit serial SPI F-RAM devices.
Add support for them to the spi-nor driver.
The actual Device ID of this chip is 7f 7f 7f 7f 7f 7f c2 2c 04. That is
six times the continuation code 7f followed by c2 for Ramtron.
Unfortunately the chip sends the Device ID in reversed order, so the
continuation code is not at the beginning, but instead at the end. Even
more unfortunate is that when reading further the chip sends more 7f
codes which means we are not even able to count the continuation codes.
We can only hope that this reversed Device ID will never match any other
devices ID.
Collisions are improbable as of now, the solution from above is good
enough. In case of future collisions one can introduce an INFO9 macro,
with the downsize that struct flash_info would grow and we have lots of
flashes. A more elegant solution would be to introduce dedicated
flash ID tables for each bank in JESP106BA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[tudor.ambarus@microchip.com: amend commit description with possible
future solutions in case collisions occur.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.
Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.
The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes. Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:
https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/
Fixes: dfd2b74530 ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry. Tested with the device and
confirmed that is working.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The SPI NOR controllers drivers must not be able to use structures that
are meant just for the SPI NOR core.
struct spi_nor_flash_parameter is filled at run-time with info gathered
from flash_info, manufacturer and sfdp data. struct spi_nor_flash_parameter
should be opaque to the SPI NOR controller drivers, make sure it is.
spi_nor_option_flags, spi_nor_read_command, spi_nor_pp_command,
spi_nor_read_command_index and spi_nor_pp_command_index are defined for the
core use, make sure they are opaque to the SPI NOR controller drivers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Create a SPI NOR manufacturer driver for Spansion chips, and move the
Spansion definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Pratyush Yadav
Tudor Ambarus
Rayagonda Kokatanur
Takahiro Kuwano
Sascha Hauer
Yicong Yang
Sergei Shtylyov
Boris Brezillon