[ Upstream commit 040b5a046a ]
Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:
sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]
Avoid this by making the prototypes unconditional.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516195046.550584-2-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f63550e2b1 ]
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x87 # out, dac
ssmset 0x06 0x07 # chip
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
(enable MCLK)
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
(enable MCLK after reset)
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
NOT OK
ssmset 0x06 0x07 # chip, out, dac
NOT OK
Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab6ecfbf40 ]
On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru
Link: https://lore.kernel.org/r/20230505062820.21840-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c51e431052 ]
Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for
Glenfly Gpus.
- In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware
limitation, need to increase hdac interrupt interval.
- In azx_first_init, enable polling mode for Glenfly Gpu. When the codec
complete the command, it sends interrupt and writes response entries to
memory, howerver, the write requests sometimes are not actually
synchronized to memory when driver handle hdac interrupt on Glenfly Gpus.
If the RIRB status is not updated in the interrupt handler,
azx_rirb_get_response keeps trying to recevie a response from rirb until
1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue.
- In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need
driver to do actual clean-ups for the linked codec when switch from one
codec to another.
Signed-off-by: jasontao <jasontao@glenfly.com>
Signed-off-by: Reaper Li <reaperlioc@glenfly.com>
Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75e5fab7db upstream.
When we run syzkaller we get below Out of Bounds error.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474
By Error checking and checking valid values issue gets rectifies.
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b271370e9 upstream.
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be1 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org
Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ca110cab4 upstream.
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230524113755.1346928-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81302b1c7c upstream.
It's reported that the recording started right after the driver probe
doesn't work properly, and it turned out that this is related with the
codec auto-suspend. Namely, after the probe phase, the usage count
goes zero, and the auto-suspend is programmed, but the codec is kept
still active until the auto-suspend expiration. When an application
(e.g. alsactl) updates the mixer values at this moment, the values are
cached but not actually written. Then, starting arecord thereafter
also results in the silence because of the missing unmute.
The root cause is the handling of "lazy update" mode; when a mixer
value is updated *after* the suspend, it should update only the cache
and exits. At the resume, the cached value is written to the device,
in turn. The problem is that the current code misinterprets the state
of auto-suspend as if it were already suspended.
Although we can add the check of the actual device state after
pm_runtime_get_if_in_use() for catching the missing state, this won't
suffice; the second call of regmap_update_bits_check() will skip
writing the register because the cache has been already updated by the
first call. So we'd need fixes in two different places.
OTOH, a simpler fix is to replace pm_runtime_get_if_in_use() with
pm_runtime_get_if_active() (with ign_usage_count=true). This change
implies that the driver takes the pm refcount if the device is still
in ACTIVE state and continues the processing. A small caveat is that
this will leave the auto-suspend timer. But, since the timer callback
itself checks the device state and aborts gracefully when it's active,
this won't be any substantial problem.
Long story short: we address the missing register-write problem just
by replacing the pm_runtime_*() call in snd_hda_keep_power_up().
Fixes: fc4f000bf8 ("ALSA: hda - Fix unexpected resume through regmap code path")
Reported-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Closes: https://lore.kernel.org/r/a7478636-af11-92ab-731c-9b13c582a70d@linux.intel.com
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230518113520.15213-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4671b7fba upstream.
Add quirk for GU603 with 0x1c62 variant of codec.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230505235824.49607-2-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90670ef774 upstream.
Add a quirk for HP EliteDesk 805 to fixup ALC3867 headset MIC no sound.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230506022653.2074343-1-aichao@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc4f2ccaed upstream.
These IDs are for AD102, AD103, AD104, AD106, and AD107 gpus with
audio functions that are largely similar to the existing ones.
Tested audio using gnome-settings, over HDMI, DP-SST and DP-MST
connections on AD106 gpu.
Signed-off-by: Nikhil Mahale <nmahale@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230517090736.15088-1-nmahale@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b44ec8c5c upstream.
get_line_out_pfx() may trigger an Oops by overflowing the static array
with more than 8 channels. This was reported for MacBookPro 12,1 with
Cirrus codec.
As a workaround, extend for the 9.1 channels and also fix the
potential Oops by unifying the code paths accessing the same array
with the proper size check.
Reported-by: Olliver Schinagl <oliver@schinagl.nl>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/64d95eb0-dbdb-cff8-a8b1-988dc22b24cd@schinagl.nl
Link: https://lore.kernel.org/r/20230516184412.24078-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 359b431547 upstream.
Line6 Pod Go (0e41:424b) requires the similar workaround for the fixed
48k sample rate like other Line6 models. This patch adds the
corresponding entry to line6_parse_audio_format_rate_quirk().
Reported-by: John Humlick <john@humlick.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230512075858.22813-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92553ee031 ]
The Pavilion 15 line has B&O top speakers similar to the x360 and
applying the same profile produces good sound. Without this, the
sound would be tinny and underpowered without either applying
model=alc295-hp-x360 or booting another OS first.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Fixes: 563785edfc ("ALSA: hda/realtek - Add quirk entry for HP Pavilion 15")
Link: https://lore.kernel.org/r/ZF0mpcMz3ezP9KQw@icequake.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e72058d5 ]
This code was supposed to return an error code if init_stream()
failed, but it instead freed dg00x->rx_stream and returned success.
This potentially leads to a use after free.
Fixes: 9a08067ec3 ("ALSA: firewire-digi00x: support AMDTP domain")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/c224cbd5-d9e2-4cd4-9bcf-2138eb1d35c6@kili.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17955aba78 ]
There is error message when defer probe happens:
fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable!
Fix the error handler with pm_runtime_enable and add
fsl_micfil_remove() for pm_runtime_disable.
Fixes: 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6bbabd2880 upstream.
commit b7898396f4 ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
added __soc_pcm_close() for non-lock version of soc_pcm_close().
But soc_pcm_close() is not using it. It is no problem, but confusable.
static int __soc_pcm_close(...)
{
=> return soc_pcm_clean(rtd, substream, 0);
}
static int soc_pcm_close(...)
{
...
snd_soc_dpcm_mutex_lock(rtd);
=> soc_pcm_clean(rtd, substream, 0);
snd_soc_dpcm_mutex_unlock(rtd);
return 0;
}
This patch use it.
Fixes: b7898396f4 ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87czctgg3w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754590651c upstream.
When DPCM tries to add valid BE connections at dpcm_add_paths(), it
doesn't check whether the picked BE actually supports for the given
stream direction. Due to that, when an asymmetric BE stream is
present, it picks up wrongly and this may result in a NULL dereference
at a later point where the code assumes the existence of a
corresponding BE substream.
This patch adds the check for the presence of the substream for the
target BE for avoiding the problem above.
Note that we have already some fix for non-existing BE substream at
commit 6246f283d5 ("ASoC: dpcm: skip missing substream while
applying symmetry"). But the code path we've hit recently is rather
happening before the previous fix. So this patch tries to fix at
picking up a BE instead of parsing BE lists.
Fixes: bbf7d3b1c4 ("ASoC: soc-pcm: align BE 'atomicity' with that of the FE")
Reported-by: Alex Natalsson <harmoniesworlds@gmail.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/CADs9LoPZH_D+eJ9qjTxSLE5jGyhKsjMN7g2NighZ16biVxsyKw@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220801170510.26582-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f620684c1 upstream.
The recent fix for DPCM locking also covered the loop in
dpcm_be_disconnect() with the FE stream lock. This caused an
unexpected side effect, thought: calling debugfs_remove_recursive() in
the spinlock may lead to lockdep splats as the code there assumes the
SOFTIRQ-safe context.
For avoiding the problem, this patch changes the disconnection
procedure to two phases: at first, the matching entries are removed
from the linked list, then the resources are freed outside the lock.
Fixes: b7898396f4 ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
Reported-and-tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220119155249.26754-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37b58becc1 upstream.
After commit bbf7d3b1c4 ("ASoC: soc-pcm: align BE 'atomicity' with
that of the FE") BE and FE atomicity must match.
In the case of Compress PCM there is a mismatch in atomicity between FE
and BE and we get errors like this:
[ 36.434566] sai1-wm8960-hifi: dpcm_be_connect: FE is atomic but BE
is nonatomic, invalid configuration
[ 36.444278] PCM Deep Buffer: ASoC: can't connect SAI1.OUT
In order to fix this we must inherit the atomicity from DAI link
associated with current PCM Compress FE.
Fixes: bbf7d3b1c4 ("ASoC: soc-pcm: align BE 'atomicity' with that of the FE")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230324124019.30826-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c75c0ea5d upstream.
The recent change for DPCM locking caused spurious lockdep warnings.
Actually the warnings are false-positive, as those are triggered due
to the nested stream locks for FE and BE. Since both locks belong to
the same lock class, lockdep sees it as if a deadlock.
For fixing this, we need to take PCM stream locks for BE with the
nested lock primitives. Since currently snd_pcm_stream_lock*() helper
assumes only the top-level single locking, a new helper function
snd_pcm_stream_lock_irqsave_nested() is defined for a single-depth
nested lock, which is now used in the BE DAI trigger that is always
performed inside a FE stream lock.
Fixes: b2ae806630 ("ASoC: soc-pcm: serialize BE triggers")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Reported-and-tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/73018f3c-9769-72ea-0325-b3f8e2381e30@redhat.com
Link: https://lore.kernel.org/alsa-devel/9a0abddd-49e9-872d-2f00-a1697340f786@samsung.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220119155249.26754-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d727e1856 ]
Smatch complains that:
snd_usb_caiaq_input_init() warn: missing error code 'ret'
This patch adds a new case to handle the situation where the
device does not support any input methods in the
`snd_usb_caiaq_input_init` function. It returns an `-EINVAL` error code
to indicate that no input methods are supported on the device.
Fixes: 523f1dce37 ("[ALSA] Add Native Instrument usb audio device support")
Signed-off-by: Ruliang Lin <u202112092@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20230504065054.3309-1-u202112092@hust.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa1e96a2b ]
A BE connected to more than one FE, e.g. in a mixer case, can go
through the following transitions.
play FE1 -> BE state is START
pause FE1 -> BE state is PAUSED
play FE2 -> BE state is START
stop FE2 -> BE state is STOP (see note [1] below)
release FE1 -> BE state is START
stop FE1 -> BE state is STOP
play FE1 -> BE state is START
pause FE1 -> BE state is PAUSED
play FE2 -> BE state is START
release FE1 -> BE state is START
stop FE2 -> BE state is START
stop FE1 -> BE state is STOP
play FE1 -> BE state is START
play FE2 -> BE state is START (no change)
pause FE1 -> BE state is START (no change)
pause FE2 -> BE state is PAUSED
release FE1 -> BE state is START
release FE2 -> BE state is START (no change)
stop FE1 -> BE state is START (no change)
stop FE2 -> BE state is STOP
The existing code for PAUSE_RELEASE only allows for the case where the
BE is paused, which clearly would not work in the sequences above.
Extend the allowed states to restart the BE when PAUSE_RELEASE is
received, and increase the refcount if the BE is already in START.
[1] the existing logic does not move the BE state back to PAUSED when
the FE2 is stopped. This patch does not change the logic; it would be
painful to keep a history of changes on the FE side, the state machine
is already rather complicated with transitions based on the last BE
state and the trigger type.
Reported-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 848aedfdc6 ]
On start/pause_release/resume, when more than one FE is connected to
the same BE, it's possible that the trigger is sent more than
once. This is not desirable, we only want to trigger a BE once, which
is straightforward to implement with a refcount.
For stop/pause/suspend, the problem is more complicated: the check
implemented in snd_soc_dpcm_can_be_free_stop() may fail due to a
conceptual deadlock when we trigger the BE before the FE. In this
case, the FE states have not yet changed, so there are corner cases
where the TRIGGER_STOP is never sent - the dual case of start where
multiple triggers might be sent.
This patch suggests an unconditional trigger in all cases, without
checking the FE states, using a refcount protected by the BE PCM
stream lock.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ae806630 ]
When more than one FE is connected to a BE, e.g. in a mixing use case,
the BE can be triggered multiple times when the FE are opened/started
concurrently. This race condition is problematic in the case of
SoundWire BE dailinks, and this is not desirable in a general
case.
This patch relies on the existing BE PCM lock, which takes atomicity into
account. The locking model assumes that all interactions start with
the FE, so that there is no deadlock between FE and BE locks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[test, checkpatch fix and clarification of commit message by plbossart]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7898396f4 ]
The existing locking for DPCM has several issues
a) a confusing mix of card->mutex and card->pcm_mutex.
b) a dpcm_lock spinlock added inconsistently and on paths that could
be recursively taken. The use of irqsave/irqrestore was also overkill.
The suggested model is:
1) The pcm_mutex is the top-most protection of BE links in the FE. The
pcm_mutex is applied always on either the top PCM callbacks or the
external call from DAPM, not taken in the internal functions.
2) the FE stream lock is taken in higher levels before invoking
dpcm_be_dai_trigger()
3) when adding and deleting a BE, both the pcm_mutex and FE stream
lock are taken.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[clarification of commit message by plbossart]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf7d3b1c4 ]
Since the flow for DPCM is based on taking a lock for the FE first, we
need to make sure during the connection between a BE and an FE that
they both use the same 'atomicity', otherwise we may sleep in atomic
context.
If the FE is nonatomic, this patch forces the BE to be nonatomic as
well. That should have no negative impact since the BE 'inherits' the
FE properties.
However, if the FE is atomic and the BE is not, then the configuration
is flagged as invalid.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
[ removed FE stream lock by tiwai ]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a9c6e1f6 ]
We allocate a structure in dpcm_be_connect(), which may be called in
atomic context. Using GFP_KERNEL is not quite right, we have to use
GFP_ATOMIC to prevent the allocator from sleeping.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 357ad4d898 upstream.
We observed: 'dmasound_setup' defined but not used error with
COMPILER=gcc ARCH=m68k DEFCONFIG=allmodconfig build.
Fix it by adding __maybe_unused to dmasound_setup.
Error(s):
sound/oss/dmasound/dmasound_core.c:1431:12: error: 'dmasound_setup' defined but not used [-Werror=unused-function]
Fixes: 9dd7c46346 ("sound/oss/dmasound: fix build when drivers are mixed =y/=m")
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220414091940.2216-1-miles.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7501f47297 upstream.
One more Pioneer quirk, this time for DDJ-800, which is quite similar like
other DJ DDJ models but with slightly different EPs or channels.
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Grégory Desor <gregory.desor@free.fr>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ZFLLzgEcsSF5aIHG@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c34890273 ]
of_node_put() should have been done directly after
mqs_priv->regmap = syscon_node_to_regmap(gpr_np);
otherwise it creates a reference leak on the success path.
To fix this, of_node_put() is moved to the correct location, and change
all the gotos to direct returns.
Fixes: a9d2736714 ("ASoC: fsl_mqs: Fix error handling in probe")
Signed-off-by: Liliang Ye <yll@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/20230403152647.17638-1-yll@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39db65a0a1 ]
The driver is able to work fine without relying on a mandatory interrupt
being assigned to the I2C device. This is only needed when making use of
the jack-detect support.
However, the following warning message is always emitted when there is
no such interrupt available:
es8316 0-0011: Failed to get IRQ 0: -22
Do not attempt to request an IRQ if it is not available/valid. This also
ensures the rather misleading message is not displayed anymore.
Also note the IRQ validation relies on commit dab472eb93 ("i2c /
ACPI: Use 0 to indicate that device does not have interrupt assigned").
Fixes: 8222576610 ("ASoC: es8316: Add jack-detect support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230328094901.50763-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9dd7c46346 upstream.
When CONFIG_DMASOUND_ATARI=m and CONFIG_DMASOUND_Q40=y (or vice versa),
dmasound_core.o can be built without dmasound_deinit() being defined,
causing a build error:
ERROR: modpost: "dmasound_deinit" [sound/oss/dmasound/dmasound_atari.ko] undefined!
Modify dmasound_core.c and dmasound.h so that dmasound_deinit() is
always available.
The mixed modes (=y/=m) also mean that several variables and structs
have to be declared in all cases.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202204032138.EFT9qGEd-lkp@intel.com
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Link: https://lore.kernel.org/r/20220405234118.24830-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e38c5e80c3 ]
The Acer Iconia One 7 B1-750 tablet mostly works fine with the defaults
for an Bay Trail CR tablet. Except for the internal mic, instead of
an analog mic on IN3 a digital mic on DMIC1 is uses.
Add a quirk with these settings for this tablet.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230322145332.131525-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 083a25b18d ]
The hw->formats may be set by snd_dmaengine_pcm_refine_runtime_hwparams()
in component's startup()/open(), but soc_pcm_hw_init() will init
hw->formats in dpcm_runtime_setup_fe() after component's startup()/open(),
which causes the valuable hw->formats to be cleared.
So need to store the hw->formats before initialization, then restore
it after initialization.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1678346017-3660-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c728b1bc5 ]
Same quirks as the 'Bishop County' NUC M15, except the rt711 is in the
'JD2 100K' jack detection mode.
Link: https://github.com/thesofproject/linux/issues/4088
Signed-off-by: Eugene Huang <eugene.huang99@gmail.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230314090553.498664-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 86a24e99c9 upstream.
dma_request_slave_channel() may return NULL which will lead to
NULL pointer dereference error in 'tmp_chan->private'.
Correct this behaviour by, first, switching from deprecated function
dma_request_slave_channel() to dma_request_chan(). Secondly, enable
sanity check for the resuling value of dma_request_chan().
Also, fix description that follows the enacted changes and that
concerns the use of dma_request_slave_channel().
Fixes: 706e2c8811 ("ASoC: fsl_asrc_dma: Reuse the dma channel if available in Back-End")
Co-developed-by: Natalia Petrova <n.petrova@fintech.ru>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230417133242.53339-1-n.zhandarovich@fintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f342ac00da upstream.
The BIOS botches this one completely - it says the 2nd S/PDIF output is
used, while in fact it's the 1st one. This is tested on DP45SG, but I'm
assuming it's valid for the other boards in the series as well.
Also add some comments regarding the pins.
FWIW, the codec is apparently still sold by Tempo Semiconductor, Inc.,
where one can download the documentation.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230405201220.2197826-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd13214a8 upstream.
It could have never worked, as snd_emu10k1_fx8010_playback_prepare() and
snd_emu10k1_fx8010_playback_hw_free() assume the emu10k1 offset for the
ETRAM, and the default DSP code includes no handler for it. It also
wouldn't make a lot of sense to make it work, as Audigy has an own, much
simpler, pass-through mechanism. So just skip creation of the device.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230405201220.2197938-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb4a624f88 upstream.
Smatch Warns:
sound/firewire/tascam/tascam-stream.c:493 snd_tscm_stream_start_duplex()
warn: missing unwind goto?
The direct return will cause the stream list of "&tscm->domain" unemptied
and the session in "tscm" unfinished if amdtp_domain_start() returns with
an error.
Fix this by changing the direct return to a goto which will empty the
stream list of "&tscm->domain" and finish the session in "tscm".
The snd_tscm_stream_start_duplex() function is called in the prepare
callback of PCM. According to "ALSA Kernel API Documentation", the prepare
callback of PCM will be called many times at each setup. So, if the
"&d->streams" list is not emptied, when the prepare callback is called
next time, snd_tscm_stream_start_duplex() will receive -EBUSY from
amdtp_domain_add_stream() that tries to add an existing stream to the
domain. The error handling code after the "error" label will be executed
in this case, and the "&d->streams" list will be emptied. So not emptying
the "&d->streams" list will not cause an issue. But it is more efficient
and readable to empty it on the first error by changing the direct return
to a goto statement.
The session in "tscm" has been begun before amdtp_domain_start(), so it
needs to be finished when amdtp_domain_start() fails.
Fixes: c281d46a51 ("ALSA: firewire-tascam: support AMDTP domain")
Signed-off-by: Xu Biang <xubiang@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230406132801.105108-1-xubiang@hust.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e98e7a82bc upstream.
snd_cs8427_iec958_active() would always delete
SNDRV_CTL_ELEM_ACCESS_INACTIVE, even though the function has an
argument `active`.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230405201219.2197811-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c17f8fd317 upstream.
Like the other boards from the D*45* series, this one sets up the
outputs not quite correctly.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230405201220.2197826-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b09c551c77 upstream.
Due to two copy/pastos, closing the MIC or EFX capture device would
make a running ADC capture hang due to unsetting its interrupt handler.
In principle, this would have also allowed dereferencing dangling
pointers, but we're actually rather thorough at disabling and flushing
the ints.
While it may sound like one, this actually wasn't a hypothetical bug:
PortAudio will open a capture stream at startup (and close it right
away) even if not asked to. If the first device is busy, it will just
proceed with the next one ... thus killing a concurrent capture.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230405201220.2197923-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa4e7a6fa1 upstream.
It's been reported that the recent kernel can't probe the PCM devices
on Roland VS-100 properly, and it turned out to be a regression by the
recent addition of the bit shift range check for the format bits.
In the old code, we just did bit-shift and it resulted in zero, which
is then corrected to the standard PCM format, while the new code
explicitly returns an error in such a case.
For addressing the regression, relax the check and fallback to the
standard PCM type (with the info output).
Fixes: 43d5ca88df ("ALSA: usb-audio: Fix potential out-of-bounds shift")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217084
Link: https://lore.kernel.org/r/20230324075005.19403-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann
Paweł Anikiel
Maxim Kochetkov
jasontao
Ravulapati Vishnu Vardhan Rao
Matthias Kaehlcke
Bin Li
Takashi Iwai
Adam Stylinski
Luke D. Jones
Ai Chao
Jeremy Soller
Nikhil Mahale
Ryan C. Underwood
Dan Carpenter
Shengjiu Wang
Kuninori Morimoto
Daniel Baluta
Ruliang Lin
Pierre-Louis Bossart
Miles Chen
Geraldo Nascimento
Liliang Ye
Cristian Ciocaltea
Randy Dunlap
Hans de Goede
Eugene Huang
Nikita Zhandarovich
Oswald Buddenhagen
Xu Biang
Jason Montleon
huangwenhui
Tim Crawford