Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium OCTEON, compute the return epc value for OCTEON specific
branch instructions.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For OCTEON, implement a save and restore of the multiplier state
across context switches.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add in the cop2 and cvmseg state info to the known proc reg
data for Cavium so that it can be tracked, saved, restored.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow precedent of other boards, and hook-up the CPU specific cache
init.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add OCTEON constants to asm/cpu.h and asm/module.h.
Add probe function for Cavium OCTEON CPUs and hook it up.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gas from binutils 2.19 fails to compile some cop1 instructions with
-march=octeon. Since the cop1 instructions are present in mips1, use
that arch instead. This will be fixed in binutils 2.20.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If on Cavium, be aware of cop2 and hwrena during do_cpu().
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium CPU, we treat the same as R10000, in that all hazards
are dealt with in hardware.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files are used to coordinate resource sharing between all of
the programs running on the OCTEON SOC. The OCTEON processor has many
CPU cores (current parts have up to 16, but more are possible). It
also has a variety of on-chip hardware blocks for things like network
acceleration, encryption and RAID.
One typical configuration is to run Linux on several of the CPU cores,
and other dedicated applications on the other cores.
Resource allocation between the various programs running on the system
(Linux kernel and other dedicated applications) needs to be
coordinated. The code we use to do this we call the 'executive'. All
of this resource allocation and sharing code is gathered together in
the executive directory.
Included in the patch set are the following files:
cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation.
All memory used by the Linux kernel is obtained here at boot time.
cvmx-l2c.c -- Coordinates operations on the shared level 2 cache.
octeon-model.c -- Probes chip capabilities and version.
The corresponding headers are in asm/octeon.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/cavium-octeon/executive/Makefile
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-bootmem.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-l2c.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
create mode 100644 arch/mips/cavium-octeon/executive/octeon-model.c
create mode 100644 arch/mips/include/asm/octeon/cvmx-asm.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootmem.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-l2c.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-packet.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-spinlock.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-sysinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx.h
create mode 100644 arch/mips/include/asm/octeon/octeon-feature.h
create mode 100644 arch/mips/include/asm/octeon/octeon-model.h
Here we define the addresses and bit-fields of the Configuration and
Status Registers (CSRs) for some of the hardware functional units on
the OCTEON SOC.
Definitions are needed for:
CIU -- Central Interrupt Unit.
GPIO -- General Purpose Input Output.
IOB -- Input / Output {Busing,Bridge}.
IPD -- Input Packet Data unit.
L2C -- Level-2 Cache controller.
L2D -- Level-2 Data cache.
L2T -- Level-2 cache Tag.
LED -- Light Emitting Diode controller.
MIO -- Miscellaneous Input / Output.
POW -- Packet Order / Work unit.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/*/stack adds the ability to query a task's stack trace. It is more
useful than /proc/*/wchan as it provides full stack trace instead of single
depth. Example output:
$ cat /proc/self/stack
[<c010a271>] save_stack_trace_tsk+0x17/0x35
[<c01827b4>] proc_pid_stack+0x4a/0x76
[<c018312d>] proc_single_show+0x4a/0x5e
[<c016bdec>] seq_read+0xf3/0x29f
[<c015a004>] vfs_read+0x6d/0x91
[<c015a0c1>] sys_read+0x3b/0x60
[<c0102eda>] syscall_call+0x7/0xb
[<ffffffff>] 0xffffffff
[add save_stack_trace_tsk() on mips, ACK Ralf --adobriyan]
Signed-off-by: Ken Chen <kenchen@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
Ralf Baechle
Manuel Lauss
David Daney
Julia Lawall
Anirban Sinha
Linus Torvalds
Bjorn Helgaas
Harvey Harrison
Matthew Wilcox
Kay Sievers
Frederik Schwarzer
Ken Chen
Mike Travis