HIGMEM support in kernel is quite mature now and we have boards
like ZOOM, PANDA, SDP where 1 GB memories are installed. With
HIGHMEM disabled not all of the 1GB of RAM (only ~700MB) can be
accessed. Hence, enable HIGMEM to make use of the entire memory.
On the boards which doesn't have more than 768 MB memory, all
the memory is directly mapped in "lowmem" and highmem isn't
exercised. Hence, there should be no impact by enabling HIGHMEM
for boards that do not need it.
Tested on OMAP4460 Panda-ES.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The supply is connected to the DSS DO-D5 pins and is thus needed for
both serial and parallel display interfaces on the igep0030 as well as
the igep0020.
If the igep0030 module isn't connected to a display, no DSI or DPI
display will be specified in board code, and the DSS driver won't enable
to VPLL2 regulator anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The INTC core is using a Kconfig option for TI816x which doesn't
exist. Convert it to use TI81XX.
Cc: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Each irq_chip for the main interrupt controller has offsets set for irq
masking registers, which added to respective base results in a pointer
to appropriate hardware register. However this is not correct for
INTC_CONTROL as there is only one INTC_CONTROL register. This does not
cause problems because generic ack code is never called, but remove
this assignment to avoid confusion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add statics to board-omap4-panda.c's internal functions and data
structures to remove sparse warnings:
arch/arm/mach-omap2/board-omap4panda.c:234:29: warning: symbol
'omap_panda_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:441:24: warning: symbol
'omap4_panda_dvi_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:451:12: warning: symbol
'omap4_panda_dvi_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:512:13: warning: symbol
'omap4_panda_display_init' was not declared. Should it be static?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the register offsets are incorrect in the OMAP mailbox code
(arch/arm/mach-omap2/mailbox.c) for the OMAP4_MAILBOX_IRQ* macros. The
discrepancy is with p.224 of TI document SPRUGX9 and p3891 of SWPU231K.
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Henry Chan <enli.chan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:170: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'phys_addr_t'
arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_init':
arch/arm/mach-omap2/dsp.c:60: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'phys_addr_t'
arch/arm/mach-omap2/dsp.c:60: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'phys_addr_t'
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current OMAP code supports couple of clocksource options based
on compilation flag (CONFIG_OMAP_32K_TIMER). The 32KHz sync-timer
and a gptimer which can run on 32KHz or system clock (e.g 38.4 MHz).
So there can be 3 options -
1. 32KHz sync-timer
2. Sys_clock based (e.g 13/19.2/26/38.4 MHz) gptimer
3. 32KHz based gptimer.
The optional gptimer based clocksource was added so that it can
give the high precision than sync-timer, so expected usage was 2
and not 3.
Unfortunately option 2, clocksource doesn't meet the requirement of
free-running clock as per clocksource need. It stops in low power states
when sys_clock is cut. That makes gptimer based clocksource option
useless for OMAP2/3/4 devices with sys_clock as a clock input.
So, in order to use option 2, deeper idle state MUST be disabled.
Option 3 will still work but it is no better than 32K sync-timer
based clocksource.
We must support both sync timer and gptimer based clocksource as
some OMAP based derivative SoCs like AM33XX does not have the
sync timer.
Considering above, make sync-timer and gptimer clocksource runtime
selectable so that both OMAP and AMXXXX continue to use the same code.
And, in order to precisely configure/setup sched_clock for given
clocksource, decision has to be made early enough in boot sequence.
So, the solution is,
Use standard kernel parameter ("clocksource=") to override
default 32k_sync-timer, in addition to this, we also use hwmod database
lookup mechanism, through which at run-time we can identify availability
of 32k-sync timer on the device, else fall back to gptimer.
Also, moved low-level SoC specific init code to respective files,
(mach-omap1/timer32k.c and mach-omap2/timer.c)
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depending on the bootloader, passing command-line arguments
with spaces may have issues. Some bootloaders doesn't seem
to pass along the quotes, passing only 'gp' part of the string,
which leads to wrong override configuration.
The only affected kernel parameter configuration for OMAP family
is "clocksource=", used to override kernel clocksource.
So this patch changes "gp timer" => "gp_timer", for clockevent,
clocksource and timer irq_handler.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
fix for a longstanding watchdog timer integration problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPqbWnAAoJEMePsQ0LvSpL+3AQAKUZP/qLl1l9duwBL8Cm9MLf
bzgCmdlHJeYlfqNJddK7qx8h/D00944Y8hbm4p/GIXTjAi6uZpW0Y0hWSTuDQNgJ
3WEP/tTTAGZDISqjTPKhp0mSQ3KCztoWKwhDmFrkQMSocDk7nGBRX1tx5ayAfmV4
OXVCAlNdo2hYzH+HSKBQZ0/z7PMv3kH+5gYEso3H36asb93V1R3KaEkrcpxhVgGZ
ViXUufWjGngR2bdNQfn621Pk38CvR+q+K0kG1QUAXnWTHxaXLgPLEJKutPVDbmme
IcViyTc59/je7kotFKbG+Hpt61ovcXk8s0UjYmEby9n8rBTxfEAbnXwMe6vSgQKN
hDN8VdMBOfxq7BjH69ylMUrUGy5juz0EWQ/tEZ3ARGKWX3KXtm2sP8lZ4hLJiGK+
MmaAjmGBkUsJ9Cj6fOFzzfbCnbxFSj64rq9YECdSYbmPJOLLPvpN1j61JToes2AZ
qdiukhgG4JFc+l/7DUObyhaY+411TLsmMEpvDS300vgq7h1CGOSBtMq+UfRUxx/J
qw/DZFEm5PWRcJTaQOVeA40iWgfhDCSd+q53Gq66SZLsdHZjs3vcdwwHZJ8OzQfK
WzWiqICNosS8Alm23suwSsIyw2xmtG3ZU6LyeUGT3AggIaqB5eOMbZTSMbhJHNV2
4cWmM2mRdb2KUaBpwuH/
=gBFx
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-c-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod-data
Some OMAP IP block data additions for 3.5, along with a
fix for a longstanding watchdog timer integration problem.
id 0 is already used and causes errors at boot:
WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'
Fix it by using the next available one (id=1).
This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.
Signed-off-by: Enrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qEmC
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Clean up of hwmod to shrink down the IP block interconnections
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-hwmod-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
ARM: OMAP2xxx: hwmod data: start to fix the IVA1, IVA2 and DSP
ARM: OMAP3: hwmod data: add IVA hard reset lines, main clock, clockdomain
ARM: OMAP3: hwmod data: fix IVA interface clock
ARM: OMAP2xxx: hwmod data: share common interface data
ARM: OMAP2xxx: hwmod data: share common hwmods between OMAP2420 and OMAP2430
ARM: OMAP2+: hwmod data: remove forward declarations, reorganize
ARM: OMAP: hwmod: remove code support for direct hwmod registration
ARM: OMAP2+: hwmod data: convert to link registration
ARM: OMAP2+: hwmod: add support for link registration
ARM: OMAP2+: hwmod: consolidate finding the MPU port index and storing it
ARM: OMAP2+: hwmod: add function to iterate over struct omap_hwmod_ocp_if
ARM: OMAP2+: hwmod: add _find_mpu_rt_port()
ARM: OMAP2+: hwmod: extend OCP_* register offsets from 16 to 32 bits
ARM: OMAP4: hwmod data: uncomment some "excluded" hwmods
ARM: OMAP4: hwmod data: add OCP_USER_DSP; mark omap44xx_dsp__iva appropriately
ARM: OMAP4: hwmod data: remove bandgap hwmod
ARM: OMAP3: hwmod data: GPTIMER12 is attached to a separate interconnect
ARM: OMAP3: hwmod data: add DSS->L3 interconnect for 3430ES1
ARM: OMAP3: hwmod data: fix interfaces for the MMC hwmods
ARM: OMAP2/3: hwmod data: update old names
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MQ+t
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Sparse and cppcheck warning fixes
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: clean up some cppcheck warnings
ARM: OMAP1: board files: deduplicate and clean some NAND-related code
ARM: OMAP: USB: remove unnecessary sideways include
ARM: OMAP: DMA: use constant array maximum, drop some LCD DMA code
ARM: OMAP: OCM RAM: use memset_io() when clearing SRAM
ARM: OMAP: fix 'using plain integer as NULL pointer' sparse warnings
ARM: OMAP2+: GPMC: resolve type-conversion warning from sparse
ARM: OMAP1: OHCI: use platform_data fn ptr to enable OCPI bus
ARM: OMAP1: OCPI: move to mach-omap1/
ARM: OMAP: add includes for missing prototypes
ARM: OMAP2+: declare file-local functions as static
Signed-off-by: Olof Johansson <olof@lixom.net>
As a prerequisite for merging the lpc32xx DT changes, this
pulls in the depends/i2c/lpc32xx branch that contains
changes to the pnx-i2c driver, which are already in the
i2c tree. The branch is available also on
git://git.antcom.de/linux-2.6.git lpc32xx/i2c
Roland Stigge <stigge@antcom.de> writes:
this is the series of the 4 patches adding device tree support to i2c-pnx
(used by LPC32xx) that Wolfram Sang already applied to the i2c subsystem.
Since both drivers/i2c/ and mach-lpc32xx are touched here, there will
probably be conflicts that you need to be aware of.
I'm posting this again for arm-soc since the actual mach-lpc32xx specific
DT conversion builds upon those changes (see next pull request), especially
in arch/arm/mach-lpc32xx/common.c.
Wolfram already gave permission to merge this via arm-soc, but please
coordinate and tell me if I can help resolving this.
Further, this implicitly updates the next/dt branch to v3.4-rc4, which
causes a trivial conflict from a change in one branch in code that
gets removed in another.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a rebased version of parts of
git://git.stlinux.com/spear/linux-2.6.git spear-v3.5
which was accidentally based on the linux-next tree and mixed too
many different things. The pinctrl related changes from the same
branch are now in the spear/pinctrl branch of arm-soc.
There are a few non-DT cleanups mixed in here, but fundamentally
it's all related to the DT conversion.
* spear/dt: (9 commits)
ARM: spear: remove most mach/*.h header contents
SPEAr: Update defconfigs
SPEAr: Add PL080 DMA support for 3xx and 6xx
ARM: SPEAr3xx: Add device-tree support to SPEAr3xx architecture
SPEAr3xx: Replace printk() with pr_*()
SPEAr6xx: Add compilation support for dtbs using 'make dtbs'
SPEAr3xx: Add clock instance of usb hosts - ehci and ohci 0 and 1
SPEAr: Use CLKDEV_INIT for defining clk_lookups
ARM: SPEAr600: Change FSMC and SMI clock names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
platform_device pdev can be NULL if CONFIG_MMC_OMAP_HS is not set.
Add check for NULL pointer. while at it move the duplicated functions
to omap4-common.c
Fixes the following boot crash seen with omap4sdp and omap4panda
when MMC is disabled.
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = c0004000
[0000008c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.4.0-rc1-05971-ga4dfa82 #4)
PC is at omap_4430sdp_init+0x184/0x410
LR is at device_add+0x1a0/0x664
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baff ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and OMAP3.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Restore of context is not done for OMAP4. This patch
adds the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE in the OMAP4
hwmod data which activates the restore for OMAP4.
Currently the OMAP4 does not hit device off still the
driver may have support for it.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and the OMAP4 hwmod data
will be using the same name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for all OMAP2xxx devices.
Assume that OMAP2xxx chips have the same HDQ idle handling bug
as OMAP3:
http://www.spinics.net/lists/linux-omap/msg63576.html
and set the OCPIF_SWSUP_IDLE flag accordingly on the HDQ's OCP interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for OMAP34xx, OMAP36xx, and AM3505/3517 devices.
According to the respective TRMs, it doesn't appear to be available for the
816x/814x or the AM335x.
The OCPIF_SWSUP_IDLE flag is added to work around an apparent hardware
bug: the hardware is not taking the CM_FCLKEN*_CORE.EN_HDQ bit into
account when considering whether to go idle:
http://www.spinics.net/lists/linux-omap/msg63576.html
This causes HDQ transfers to fail or become corrupt. Thanks to
NeilBrown for his help diagnosing and testing fixes for this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Much of the HDQ1W integration data is common between multiple generations
of OMAP SoCs, so rather than make several copies, we add it once into
files which are compiled for multiple SoCs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Implement a custom reset function for the HDQ1W IP block. This is
because the HDQ1W IP block, like I2C, has an internal clock gating bit
that needs to be toggled after setting the SOFTRESET bit to allow the
reset to propagate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avinash.H.M <avinashhm@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Add MMC for 2420 so we can pass the DMA request lines the same
way as we already do on omap2430 and later.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to apply on top of the 3.5 hwmod cleanup;
changed mmc hwmod name/class to "msdi" as documented in the 2420 TRM Rev X;
added sysconfig register information; added 16 bit register width flag;
added MSDI custom reset code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
powerdomain, PRM, and CM changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Q4kv
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-prcm
Some OMAP PRCM updates for 3.5. Includes some clock, clockdomain,
powerdomain, PRM, and CM changes.
The system dma module has capabiities register indicating
the support for descriptor loading, constant fill, etc.
Use this instead of OMAP revision check to identify the features
supported runtime.
This avoids patching the code for feature SOCs which has
those capabilities.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
EMIF, GMPC and DMM driver can ioremap() the address
space as part of driver intialisation and there is
no need to have static IO mapping for them.
Hence remove the un-used static IP space and let
the respective drivers manage it as part if driver
init.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Current OMAP code doesn't use any of the OMAP_WKG_ENB_SECURE_*
registers.
So remove those defines.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Since OMAP4 code base now makes use of OMAP4 specific PRCM functions,
cm2xxx_3xxx.c need not be compiled for OMAP4 only builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Clean up clockdomains3xxx_data.c a bit by removing the superfluous
commas in gfx_sgx_3xxx_wkdeps[].
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With patch 'ARM: OMAP2+: powerdomain: Wait for powerdomain transition
in pwrdm_state_switch()', the pwrdm_clkdm_state_switch() API becomes
duplicate of pwrdm_state_switch().
Get rid off duplicate pwrdm_clkdm_state_switch() and update the
users of it with pwrdm_state_switch()
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the correct clockdomain for the HDQ functional clock. This is needed
for the clock and hwmod PM code to work correctly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
The current DPLL code enables and disables autoidle features
without checking whether the autoidle register is available.
Fix this by putting a check for the existence of the autoidle
register in the DPLL data.
With such a check in place, for DPLLs which do not support this
feature, simply skipping the autoidle_reg entry in the DPLL data
is sufficient.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We do not use iclk anywhere in the dmtimer driver and so removing it.
Hence removing the timer iclk entries from OMAP4 clkdev table as well.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Instead of statically defining seperate arrays for every OMAP4+ archs,
have a generic init function to populate the arrays. This avoids the
need for creating new array for every arch added in the future that
reuses the prm and cm registers read/write code.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing idle_st bit for 32k-sync timer into the prcm-common
header file, required for hwmod data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register bits for MPU_CLK_SRC and IVA2_CLK_SRC in CM_CLKSEL1_PLL
register are 3 bits wide. Fix the MASK definition accordingly.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To improve the clarity of the code, replace the CK_3517 flag used in
the clock data with CK_AM35XX. The CK_3505 flag can also be
removed, since it is now unused.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The init for 3505/3517 specific clocks depends on the ordering of
cpu_is checks, is error prone and confusing (there are 2 separate
checks for cpu_is_omap3505()).
Remove the 3505-specific checking since CK_3505 flag is not used, and
treat all AM35x clocks the same.
This means that the SGX clock (the only AM35x clkdev not currently
flagged for 3505) will now be registered on 3505, but that is
harmless. That can be cleaned up when the clkdev nodes are removed in
favor of them being registered by hwmod.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The AM35x UART4 is common to all AM35x devices, so use CK_AM35XX instead
of (CK_3505 | CK_3517), which is equivalent.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At init time, check the powerdomains lookup is successful otherwise
exit the cpuidle driver init function with -ENODEV like what is done for the
omap3 cpuidle driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This reverts commit 46f8c3c7e9.
The commit above swapped the DSI1_PPID and DSI2_PPID register fields in
CONTROL_DSIPHY to be in sync with the newer public OMAP TRMs(after version V).
With this commit, contention errors were reported on DSI lanes some OMAP4 SDPs.
After probing the DSI lanes on OMAP4 SDP, it was seen that setting bits in the
DSI2_PPID field was pulling up voltage on DSI1 lanes, and DSI1_PPID field was
pulling up voltage on DSI2 lanes.
This proves that the current version of OMAP4 TRM is incorrect, swap the
position of register fields according to the older TRM versions as they were
correct.
Cc: stable@vger.kernel.org # v3.2+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
struct powerdomain varialbes are all file local, make them static.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: update changelog, drop error check in fast path]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reduce the scope of the omap3_idle_data to the file as it is only used
in cpuidle34xx.c.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Simplify the indentation by removing the useless 'else' statement.
Remove the first loop for the 'idx' search as we have it already
with the 'index' passed as parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We are storing the 'omap3_idle_data' in the private data field
of the cpuidle device. As we are using this variable only in this file,
that does not really make sense. Let's use the global variable directly.
As the table is initialized statically, let's remove the initialization at
startup too.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialize the omap3_idle_data array at compile time, that will allow
to remove the initialization at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We do not longer need the ''cpuidle_params_table' array as
we defined the states in the driver and we checked they are
all valid.
We also remove the structure definition as it is no longer used.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With the previous changes all the states are valid, except the last
state which is now handled at runtime by next_valid_state() based on
the errata flags.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: minor changelog rework]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The errata check is done in the next_valid_state function, no need to check
that in the omap3_idle_init function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use the new cpuidle API and define in the driver the states.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As suggested, this table is an optimized version for rx51 and we
remove it in order to consolidate the cpuidle code between omap3
and omap4, we remove this specific data definition which is used
to override the default omap3 latencies but at the cost of extra
code and complexity.
In order to not lose the values which probably took time to be
measured, the table is converted into a comment with an array
description.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We initialized it at compile time, no need to do that at boot
time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We are storing the 'omap4_idle_data' in the private data field
of the cpuidle device. As we are using this variable only in this file,
that does not really make sense. Let's use the global variable directly.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We initialize the omap4_idle_data variable at compile time allowing us
to remove in the next patch the initialization done at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add the static declaration for the omap4_idle_data variable because its scope
is in the file only.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We do not longer need this table as we defined the values
in the driver states.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The cpuidle API allows to declare statically the states in the driver
structure. Let's use it.
We do no longer need the fill_cstate function called at runtime and
by the way adding more instructions at boot time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The 'valid' field is never used in the code, let's remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ToTm
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-a-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-hwmod
Add in most of the remaining hwmods (IP block descriptions) for the
OMAP44xx family of SoCs. There still seem to be a few missing, such
as those for the MMU IP blocks, but this seems to cover the bulk of
the remainder.
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NqUz
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-hwmod
Clean up various aspects of the OMAP hwmod code, which is the IP block
control code for OMAP SoCs. In particular, this series results in
a considerable diffstat savings by changing the way that IP block
interconnections are defined.
Add a skeleton hwmod for the DEBUGSS and associated interconnect data.
This is a basic set of data that will need further additions as
further DEBUGSS information becomes available.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRCM, CM, PRM, and related hwmod and associated interconnect
data. These IP blocks handle most of the on-chip power, reset, and clock
control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the System Control Module hwmod and associated interconnect data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the OCP-WP hwmod and associated interconnect data. The OCP-WP,
or OCP watchpoint, can be used to collect interconnect data and
transmit it via the STM port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the OCM RAM IP block and interconnect data. This is an oh-chip
block of SRAM connected directly to the L3 bus.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the OCP2SCP IP block and interconnect data. The OCP2SCP can be
used in conjunction with the on-chip embedded USB PHY, associated with
the OTG controller.
Add the on-chip full-speed USB host controller IP block and
interconnect data.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the SL2 interface IP block and interconnect data. The SL2 is related
to the IVA-HD subsystem.
Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect. This can provide a direct system interconnect link to
other devices stacked on the OMAP package.
Add the ELM IP block and interconnect data. The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the McASP hwmod and associated interconnect data. The McASP is a
general-purpose audio serial port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the Slimbus hwmods and associated interconnect data. The Slimbus
IP blocks implement a two-wire serial interface.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the GPU hwmod and associated interconnect data. The GPU is a
graphics accelerator.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the EMIF1 and 2 hwmods and associated interconnect data. The EMIFs
are SDRAM interface IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add the GPMC hwmod and associated interconnect data. The GPMC is a
programmable parallel-bus memory controller.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ/1-wire hwmod and associated interconnect data. The
HDQ/1-wire IP block is a low-speed serial interconnect.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Add hwmod data for the OMAP4 FDIF IP block.
This patch also includes a change (originally from Fernando Guzman
Lugo <fernando.lugo@ti.com>) to set a softreset delay for the FDIF IP
block:
http://www.spinics.net/lists/arm-kernel/msg161874.html
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: rearranged to match script output; fixed FDIF end address to
match script data; wrote trivial changelog; combined the FDIF portion of
Fernando's srst_udelay patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The PRM and CM implicit clockdomains will soon be used by OMAP44xx.
So, make them common to OMAP2+ and modify the OMAP4 clockdomains code
so use of these clockdomains doesn't crash the system.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
N800 logs this message on boot:
[ 0.182281] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by creating basic IVA1 and DSP hwmods for OMAP2420, and a basic IVA2
hwmod for OMAP2430. There is still more information to be added, but
this should resolve the immediate issue.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The IVA hwmod data is missing some fields that cause the following
warning on boot:
[ 0.118011] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by encoding the IP block's main functional clock, reset lines, and
clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data listed iva2_ck as an interface clock between the
IVA and L3. This is incorrect. iva2_ck is not an interface clock.
Since it cannot auto-idle, specifying it here prevents the IVA and at
least one of the CORE clockdomains from going idle, which causes PM
problems such as these upon system suspend:
[ 70.626129] Powerdomain (iva2_pwrdm) didn't enter target state 1
[ 70.626190] Powerdomain (core_pwrdm) didn't enter target state 1
Fix by specifying the actual interface clock in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several struct omap_hwmod_ocp_if records can be shared between OMAP2420
and OMAP2430. Move these shared records out of the chip-specific files
into mach-omap2/omap_hwmod_2xxx_interconnect_data.c. This should save some
memory and source lines, at the cost of readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Santosh Shilimkar
Laurent Pinchart
Kevin Hilman
Grazvydas Ignotas
Chris Lalancette
Tomi Valkeinen
Tony Lindgren
Felipe Contreras
Vaibhav Hiremath
Enrico Butera
Olof Johansson
Arnd Bergmann
Balaji T K
Peter Ujfalusi
Shubhrajyoti D
Paul Walmsley
Shawn Guo
R Sricharan
Mark A. Greer
Vaibhav Bedia
Tarun Kanti DebBarma
Rajendra Nayak
Daniel Lezcano
Archit Taneja
Greg Kroah-Hartman
Linus Torvalds
Benoît Cousson
Ming Lei