The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on commit 02cb009 for pata_cs5530.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checking of the currently programmed UDMA mode.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Currently, ide_cmd_ioctl when invoked for setting DMA transfer mode calls
ide_find_dma_mode with requested mode as XFER_UDMA_6. This prevents setting DMA
mode to any other value than the default (maximum) supported by the device (or
UDMA6, if supported) irrespective of the actual requested transfer mode and
returns error.
For example, setting mode to UDMA2 using hdparm, where UDMA4 is the default
transfer mode gives following error:
# ./hdparm -d1 -Xudma2 /dev/hda
/dev/hda:hda: UDMA/66 mode selected
setting using_dma to 1 (on)
hda: UDMA/66 mode selected
setting xfermode to 66 (UltraDMA mode2)
HDIO_DRIVE_CMD(setxfermode) failed: Invalid argument
using_dma = 1 (on)
This patch fixes the issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_request_mem_region.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_{ioremap/io_port_map}.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for {request/release}_mem_region and ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been enough time since introduction of the new timing tables
(commit 809b53c from Dec 12 2007) and the old timing tables are still
available in pata_hpt37x.c (or git history) if somebody needs them.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-cs.c is the only PCMCIA device driver making use of CONFIG_PCMCIA_DEBUG,
so convert it to use the dynamic debug infrastructure.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This reverts commit 6029336426.
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Kconfig text for CONFIG_IDE doesn't give a hint to users that this
subsystem is currently in maintenance mode and isn't actively developed.
Let's correct this by marking it as deprecated, and also get rid of a bunch of
unnecessary text that doesn't really have anything to do with what the option is
for.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the BKL calls in the chrdev_{open,release} interfaces with a
simple sleeping mutex.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two have been long unused but I've just noticed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
Revert "Revert "ide: try to use PIO Mode 0 during probe if possible""
sis5513: fix PIO setup for ATAPI devices
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.
This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 6029336426).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6029336426.
Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
ide: fixup for fujitsu disk
ide: convert to ->proc_fops
at91_ide: remove headers specific for at91sam9263
IDE: palm_bk3710: convert clock usage after clkdev conversion
ide: fix races in handling of user-space SET XFER commands
ide: allow ide_dev_read_id() to be called from the IRQ context
ide: ide-taskfile.c fix style problems
drivers/ide/ide-cd.c: Use DIV_ROUND_CLOSEST
ide-tape: fix handling of postponed rqs
ide-tape: convert to ide_debug_log macro
ide-tape: fix debug call
ide: Fix annoying warning in ide_pio_bytes().
IDE: Save a call to PageHighMem()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
...
->read_proc, ->write_proc are going away, ->proc_fops should be used instead.
The only tricky place is IDENTIFY handling: if for some reason
taskfile_lib_get_identify() fails, buffer _is_ changed and at least
first byte is overwritten. Emulate old behaviour with returning
that first byte to userspace and reporting length=1 despite overall -E.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver requires only static memory controller definitions and macroses
contained in generic header at91sam9_smc.h.
Those extra headers are misleading since this driver also works fine for
at91sam9260 SoC: tests were performed on afeb9260 board.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Make cmd->tf_flags field 'u16' and add IDE_TFLAG_SET_XFER taskfile flag.
* Update ide_finish_cmd() to set xfer / re-read id if the new flag is set.
* Convert set_xfer_rate() (write handler for /proc/ide/hd?/current_speed)
and ide_cmd_ioctl() (HDIO_DRIVE_CMD ioctl handler) to use the new flag.
* Remove no longer needed disable_irq_nosync() + enable_irq() from
ide_config_drive_speed().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Un-static __ide_wait_stat().
* Allow ide_dev_read_id() helper to be called from the IRQ context by
adding irq_ctx flag and using mdelay()/__ide_wait_stat() when needed.
* Switch ide_driveid_update() to set irq_ctx flag.
This change is needed for the consecutive patch which fixes races in
handling of user-space SET XFER commands but for improved bisectability
and clarity it is better to do it in a separate patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix trivial style problems:
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: space prohibited between function name and open parenthesis '('
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
ERROR: do not use C99 // comments X 2
ERROR: trailing statements should be on next line
ERROR: trailing whitespace
ERROR: switch and case should be at the same indent
WARNING: line over 80 characters
total: 5 errors, 4 warnings
Also removed dead code
Also used pr_err() to avoid line breaks
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-tape used to hit
[ 58.614854] ide-tape: ht0: BUG: Two DSC requests queued!
due to the fact that another rq was being issued while the driver was
waiting for DSC to get set for the device executing ATAPI commands which
set the DSC to 1 to indicate completion.
Here's a sample output of that case:
issue REZERO_UNIT
[ 143.088505] ide-tape: ide_tape_issue_pc: retry #0, cmd: 0x01
[ 143.095122] ide: Enter ide_pc_intr - interrupt handler
[ 143.096118] ide: Packet command completed, 0 bytes transferred
[ 143.106319] ide-tape: ide_tape_callback: cmd: 0x1, dsc: 1, err: 0
[ 143.112601] ide-tape: idetape_postpone_request: cmd: 0x1, dsc_poll_freq: 2000
we stall the ide-tape queue here waiting for DSC
[ 143.119936] ide-tape: ide_tape_read_position: enter
[ 145.119019] ide-tape: idetape_do_request: sector: 4294967295, nr_sectors: 0
and issue the new READ_POSITION rq and hit the check.
[ 145.126247] ide-tape: ht0: BUG: Two DSC requests queued!
[ 145.131748] ide-tape: ide_tape_read_position: BOP - No
[ 145.137059] ide-tape: ide_tape_read_position: EOP - No
Also, ->postponed_rq used to point to that postponed request. To make
things worse, in certain circumstances the rq it was pointing to got
replaced unterneath it by swiftly reusing the same rq from the mempool
of the block layer practically confusing stuff even more.
However, we don't need to keep a pointer to that rq but simply wait for
DSC to be set first before issuing the follow-up request in the drive's
queue. In order to do that, we make idetape_do_request() first check the
DSC and if not set, we stall the drive queue giving the other device on
that IDE channel a chance.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove tape->debug_mask and use drive->debug_mask instead.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error only occurs when IDETAPE_DEBUG_LOG is enabled.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC can't see that flags is only set and used when PageHighmem() is
true.
Inspired by a patch from Jean Delvare.
Signed-off-by: David S. Miller <davem@davemloft.net>
PageHighMem() isn't cheap so avoid calling it twice on the same page.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't leak kernel stack information through uninitialized structure members.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory
leak after writing lots of data, the kmalloc-96 slab cache keeps
growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush
is never kfreed.
Commit a09485df9c ("ide: move request
type specific code from ide_end_drive_cmd() to callers (v3)") and
f505d49ffd ("ide: fix barriers support")
cause this regression, cmd->rq must now be set for ide_complete_cmd to
honor the IDE_TFLAG_DYN flag.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory overrun in function ide_get_identity_ioctl() which
chooses the size of a memory buffer depending on the ioctl command that led
to the function call, however, passes that buffer to a function which needs the
buffer size to be always chosen unconditionally.
Due to conditional compilation the memory overrun can only happen on big endian
machines. The error can be triggered using ioctl HDIO_OBSOLETE_IDENTITY. Usage
of ioctl HDIO_GET_IDENTITY is safe.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2f0d0fd2a6 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.
Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).
While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some devices in the wild that clear the DRQ bit during the
last word of a packet command and therefore could use a "second chance"
for that last word of data to be xferred instead of simply failing the
request. Do that by attempting to suck in those last bytes in PIO mode.
In addition, the ATA_ERR bit has to be cleared for we cannot be sure the
data is valid otherwise.
See http://bugzilla.kernel.org/show_bug.cgi?id=13399 for details.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_kill_rq()
and ide_floppy_do_request() for failed requests.
[ bugfix part ]
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_do_devset()
and ide_complete_drive_reset(). Then remove ide_rq_bytes().
[ cleanup part ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such requests should be failed with -EIO (like all other requests
in this function) instead of being completed successfully.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 86ccf37c6a the driver was modified
to deal with the removal of the pciirq argument to ide_pci_setup_ports().
But in the conversion only the first port's IRQ gets setup.
Inspired by a patch by Bartlomiej Zolnierkiewicz., and with help from
Alan Cox.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hwif->rq point to PM request during PM sequence and do not allow
any other types of requests to slip in (the old comment was never correct
as there should be no such requests generated during PM sequence).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some broken devices that report multiple DMA xfer modes
enabled at once (ATA spec doesn't allow it) but otherwise work fine
with DMA so just delete ide_id_dma_bug().
[ As discovered by detective work by Frans and Bart, due to how
handling of the ID block was handled before commit c419993
("ide-iops: only clear DMA words on setting DMA mode") this
check was always seeing zeros in the fields or other similar
garbage. Therefore this check wasn't actually checking anything.
Now that the tests actually check the real bits, all we see are
devices that trigger the check yet work perfectly fine, therefore
killing this useless check is the best thing to do. -DaveM ]
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the error gets repeated too frequently, for example each
time HAL polls the device when a disc is present. Avoid that by using
printk_once instead of printk.
Also join the error and corrective action messages into a single line.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frans Pop reported that his CDROM drive reports a blocksize of 2352,
and this causes new warnings due to commit
e8e7b9eb11 ("ide-cd: fix oops when using
growisofs").
What we're trying to do is make sure that "blocklen >> SECTOR_BITS"
is something the block layer won't choke on.
And for Frans' case "2352 >> SECTOR_BITS" is equal to
"2048 >> SECTOR_BITS", and thats "4".
So warning in this case gives no real benefit.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ide_host_enable_irqs() helper and use it in ide_host_register()
before registering ports. Then remove no longer needed IRQ unmasking
from in init_irq().
This should fix the problem with "screaming" shared IRQ on the first
port (after request_irq() call while we have the unexpected IRQ pending
on the second port) which was uncovered by my rework of the serialized
interfaces support.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This begins to fix regressions reported by Frans Pop on his Ultra-10.
There are still some funnies left that we are investigating.
Signed-off-by: David S. Miller <davem@davemloft.net>
With 2.6.30, the error handling code in cdrom_newpc_intr was changed
to deal with partial request failures by normally completing the 'good'
parts of a request and only 'error' the last (and presumably,
incompletely transferred) bio associated with a particular
request. In order to do this, ide_complete_rq is called over
ide_cd_error_cmd() to partially complete the rq. The block layer
does partial completion only for requests with bio's and if the
rq doesn't have one (eg 'GPCMD_READ_DISC_INFO') the request is
completed as a whole and the drive->hwif->rq pointer set to NULL
afterwards. When calling ide_complete_rq again to report
the error, this null pointer is derefenced, resulting in a kernel
crash.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13399.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-ide@vger.kernel.org
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unsupported requests should be never handed down to device drivers
and the best thing we can do upon discovering such request inside
driver's ->do_request method is to just BUG().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ide_drive_t 'drive_data' field from 'unsigned int' type to 'void *'
type, allowing a wider range of values/types to be stored in this field.
Added 'ide_get_drivedata' and 'ide_set_drivedata' helpers to get and set
the 'drive_data' field.
Fixed all host drivers to maintain coherency with the change in the
'drive_data' field type.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
[bart: fix qd65xx build, cast to 'unsigned long', minor Coding Style fixups]
Acked-by: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Implement test_irq() method based on the driver's former dma_test_irq() methods.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Implement test_irq() method based on the driver's former dma_test_irq() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_test_irq() methods into test_irq() methods. The
driver will now use the standard dma_test_irq() method implementation which
allows to remove 'cmd54x_dma_ops' and 'cmd648_dma_ops' that become identical
to 'sff_dma_ops'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move the ack_intr() method into 'struct ide_port_ops', also renaming it to
test_irq() while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are now two methods that clear the port interrupt: ack_intr() method,
implemented only on M680x0 machines, that is called at the start of ide_intr(),
and clear_irq() method, that is called somewhat later in this function. In
order to stop this duplication, delegate the task of clearing the interrupt
to clear_irq() method, only leaving to ack_intr() the task of testing for the
port interrupt.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove interrupt bit test (not trusted anyway) from siimage_io_dma_test_irq()
and siimage_mmio_dma_test_irq() -- this allows to replace the former function
with now identical ide_dma_test_irq()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_end() methods into clear_irq() methods -- the
driver will now use the standard dma_end() method implementation, ide_dma_end().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now the clear_irq() method is called only from ide_intr() but ide_timer_expiry()
also should call this method in case when drive_is_ready() succeeds...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several errors and warnings given by checkpatch.pl:
- space between the asterisk and parameter name;
- inconsistent spacing between operator and operands;
- space between *sizeof* and open parenthesis;
- #include <asm/io.h> instead of #include <linux/io.h>
- use of *typedef* instead of a structure tag;
- line over 80 characters.
In addition to these changes, also do the following:
- indent with tabs instead of spaces;
- put the function's result type and name/parameters on the same line;
- join back the needlessly broken lines;
- get rid of needless type cast in sgiioc4_checkirq();
- remove space between the type cast and the variable name;
- remove commented out field initializer;
- uppercase the acronyms, lowercase the normal words in the comments;
- fix up the multi-line comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'unsigned long port_flags' field to ide_hwif_t.
* Add IDE_PFLAG_PROBING port flag and keep it set during probing.
* Fix ide_pio_need_iordy() to not enable IORDY at a probe time
(IORDY may lead to controller lock up on certain controllers
if the port is not occupied).
Loosely based on the recent libata's fix by Tejun, thanks to Alan
for the hint that IDE may also need it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_pio_need_iordy() helper and convert host drivers to use it.
This fixes it8172, it8213, pdc202xx_old, piix, slc90e66 and siimage
host drivers to handle IORDY correctly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits)
ide: re-implement ide_pci_init_one() on top of ide_pci_init_two()
ide: unexport ide_find_dma_mode()
ide: fix PowerMac bootup oops
ide: skip probe if there are no devices on the port (v2)
sl82c105: add printk() logging facility
ide-tape: fix proc warning
ide: add IDE_DFLAG_NIEN_QUIRK device flag
ide: respect quirk_drives[] list on all controllers
hpt366: enable all quirks for devices on quirk_drives[] list
hpt366: sync quirk_drives[] list with pdc202xx_{new,old}.c
ide: remove superfluous SELECT_MASK() call from do_rw_taskfile()
ide: remove superfluous SELECT_MASK() call from ide_driveid_update()
icside: remove superfluous ->maskproc method
ide-tape: fix IDE_AFLAG_* atomic accesses
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
pdc202xx_old: kill resetproc() method
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
pdc202xx_old: use ide_dma_test_irq()
ide: preserve Host Protected Area by default (v2)
ide-gd: implement block device ->set_capacity method (v2)
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (28 commits)
ide-tape: fix debug call
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
ide-dma: don't reset request fields on dma_timeout_retry()
ide: drop rq->data handling from ide_map_sg()
ide-atapi: kill unused fields and callbacks
ide-tape: simplify read/write functions
ide-tape: use byte size instead of sectors on rw issue functions
ide-tape: unify r/w init paths
ide-tape: kill idetape_bh
ide-tape: use standard data transfer mechanism
ide-tape: use single continuous buffer
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
ide-tape,floppy: fix failed command completion after request sense
ide-pm: don't abuse rq->data
ide-cd,atapi: use bio for internal commands
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
ide-cd: convert to using generic sense request
ide: add helpers for preparing sense requests
ide-cd: don't abuse rq->buffer
ide-atapi: don't abuse rq->buffer
...
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PowerMac bootup with CONFIG_IDE=y oopses in ide_pio_cycle_time():
because "ide: try to use PIO Mode 0 during probe if possible" causes
pmac_ide_set_pio_mode() to be called before drive->id has been set.
Bart points out other places which now need drive->id set earlier,
so follow his advice to allocate it in ide_port_alloc_devices()
(using kzalloc_node, without error message, as when allocating drive)
and memset it for reuse in ide_port_init_devices_data().
Fixed in passing: ide_host_alloc() was missing ide_port_free_devices()
from an error path.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_probe_port() skip probe if ide_port_wait_ready() returns -ENODEV
and print error message instead of debug one if it returns -EBUSY.
v2:
Fix the default 'rc' value.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_NIEN_QUIRK device flag and use it instead of
drive->quirk_list.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_nien_quirk_list() helper to the core code
and then use it in ide_port_tune_devices().
* Remove no longer needed ->quirkproc methods from hpt366.c
and pdc202xx_{new,old}.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enable also quirks in do_reset1() and ide_config_drive_speed()
for devices on quirk_drives[] list.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With ->write_devctl method call (which unmasks drive IRQ) preceding
SELECT_MASK() call there is really no need for the latter.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We always call SELECT_MASK(drive, 0) after ide_dev_read_id() call
so there is no need to do it again in the error path.
Moreover with the combination of HPT36x controller and the drive on
the quirk_drives[] list this can result in superfluous enable_irq()
call which in turn will trigger WARN() in __enable_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[inspired by pata_icside]
Enabling/disabling of card IRQs is handled fine by IRQ and IDE
subsystems so there is no need for custom ->maskproc method.
Moreover icside_maskproc() would enable IRQ only if it was already
enabled [because of 'if (state->enabled && !mask)' check].
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These flags used to be bit numbers and now are single bits in the
->atapi_flags vector. Use them properly.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are two sites where the flag is being changed: ide_retry_pc
and idetape_do_request. Both codepaths are protected by hwif->busy
(ide_lock_port) and therefore we shouldn't need the atomic accesses.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's resetproc() method resets both channels at once -- most probably
by driving RESET- on them. Not only such reset can severely disturb concurrent
operations on another channel, it also ensues 2-second delay, while there's no
apparent reason why SRST reset being performed prior to resetproc() call needs
to be followed up by another reset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_lost_irq() and dma_clear() methods call pdc202xx_reset()
which resets both channels at once -- most probably by driving RESET- on them.
Not only such reset can severely disturb concurrent operations on another
channel, it is also a clear overkill (especially in the first case) and is
completely unexpected and thus not properly handled by the IDE core in this
context (in the second case the usual SRST reset would most probably ensue
anyway though); it also causes quite arbitrary 2-second delay. Hence, use the
standard ide_dma_lost_irq() method and don't install the optional dma_clear()
method at all -- the driver should do well without this age-old cruft...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's dma_test_irq() method, although tests some chip specific interrupt
bits, finally always relies on the SFF-8038i standard interrupt bit. I see no
point in testing the bits that are not trusted anyway -- the driver should be
fully able to use the standard method implemetation, ide_dma_test_irq().
With this change 'pdc202xx_dma_ops' finally becomes identical to 'sff_dma_ops',
and we can get rid of it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit ac95beedf8 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit 942dcd85bf
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit 4b58f17d7c
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The recent move to accessor functions for querying queue limits
missed an entry in ide-disk.c:
drivers/ide/ide-disk.c: In function ‘ide_disk_setup’:
drivers/ide/ide-disk.c:642: error: ‘struct request_queue’ has no member named ‘max_sectors’
Fix it.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_regs_t typedef and rename struct hw_regs_s to struct ide_hw.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Pass number of ports to ide_host_{alloc,add}() and then update
all users accordingly.
v2:
- drop no longer needed NULL initializers in buddha.c, cmd640.c and gayle.c
(noticed by Sergei)
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert host drivers that still use hw_regs_t's chipset field to use
the one in struct ide_port_info instead.
* Move special handling of ide_pci chipset type from ide_hw_configure()
to ide_init_port().
* Remove chipset field from hw_regs_t.
While at it:
- remove stale comment in delkin_cb.c
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace:
- special_t typedef by IDE_SFLAG_* flags
- 'special_t special' ide_drive_t's field by 'u8 special_flags' one
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- change debug printk() level to KERN_DEBUG and use __func__
- update documentation
v2:
- fix DEBUG build (noticed by Sergei)
There should be no functional changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Initially set PIO Mode 0 for all host drivers that have a 'set_pio_mode'
method before the IDE core figures out the most suited PIO mode for the
attached device.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This error only occurs when IDETAPE_DEBUG_LOG is enabled.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c10726 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_check_ireason() function that handles all ATAPI devices.
Reorganize all unlikely cases in ireason checking further down in the
code path.
In addition, add PFX for printks originating from ide-atapi. Finally,
remove ide_cd_check_ireason.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now that we use a static request_sense buffer, use it instead of the
first 18 bytes only. Also, remove sense-arg to cdrom_analyze_sense_data
and cdrom_log_sense since we can access it through drive->sense_data
now.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now after all users of pc->buf have been converted, remove the 64B buffer
embedded in each packet command.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
ide-tape used to issue READ POSITION in several places and the
evaluation of the returned READ POSITION data was done in the
->pc_callback. Convert it to use local buffer and move that
evaluation chunk in the idetape_read_position(). Additionally, fold
idetape_create_read_position_cmd() into it, too, thus concentrating READ
POSITION handling in one method only and making all places call that.
Finally, mv {idetape,ide_tape}_read_position.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Access the sense buffer through the bio in ->pc_callback method thus
alleviating the need for the pc->buf pointer.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Pass the buffer into ide_floppy_create_format_unit_cmd instead of using
pc->buf.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This is in preparation of removing ide_atapi_pc. Expose the buffer as an
argument to ide_queue_pc_tail with later replacing it with local buffer
or even kmalloc'ed one if needed due to stack usage constraints.
Also, add the possibility of passing a NULL-ptr buffer for cmds which
don't transfer data besides the cdb. While at it, switch to local buffer
in idetape_get_mode_sense_results().
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This is in preparation for removing ide_atapi_pc.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now that we have rq->resid_len, use it to account partial completion
amount during the lifetime of an rq, decrementing it on each successful
transfer. As a result, get rid of now unused pc->xferred.
While at it, remove noisy debug call in ide_prep_sense.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
After the recent struct request cleanups, blk_rq_bytes() is guaranteed
to be valid and is the current total length of the rq's bio. Use that
instead of pc->req_xfer in the do_request() path after the command has
been queued
The remaining usage of pc->req_xfer now is only until we map the rq to a
bio.
While at it:
- remove local caching of rq completion length in ide_tape_issue_pc()
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
ide-tape had a potential bug for fs requests when preparing the command
packet: it was writing the transfer length as a number of fixed blocks.
However, the block layer implies 512 byte blocks and ide-tape can have
other block sizes so account for that too.
ide-floppy does this calculation properly with the block size factor
(floppy->bs_factor).
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide generally has single request in flight and tracks it using
hwif->rq and all state handlers follow the following convention.
* ide_started is returned if the request is in flight.
* ide_stopped is returned if the queue needs to be restarted. The
request might or might not have been processed fully or partially.
* hwif->rq is set to NULL, when an issued request completes.
So, dequeueing model can be implemented by dequeueing after fetch,
requeueing if hwif->rq isn't NULL on ide_stopped return and doing
about the same thing on completion / port unlock paths. These changes
can be made in ide-io proper.
In addition to the above main changes, the following updates are
necessary.
* ide-cd shouldn't dequeue a request when issuing REQUEST SENSE for it
as the request is already dequeued.
* ide-atapi uses request queue as stack when issuing REQUEST SENSE to
put the REQUEST SENSE in front of the failed request. This now
needs to be done using requeueing.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all direct users
to accessors.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide doesn't manipulate request fields anymore and thus all hard and
their soft equivalents are always equal. Convert all references to
accessors.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->sector is set to the tape->first_frame but it's never actually
used and not even in the correct unit (512 byte sectors). Don't set
it.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some time ago we had to disable init_hwif callback for PowerPC builds.
That was because of a historical IRQ overwrite in the driver, which
was causing IDE malfunction on the MPC8610HPCD PowerPC boards.
It's unclear whether this overwrite is still useful, but it is proven
to cause a bit of harm, and today some PowerPC targets (Xilinx ML510,
as reported by Roderick Colenbrander) need the init_hwif, so we have
to re-enable it and remove the overwrite.
Reported-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Original patch (dfa4411cc3) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Benjamin Herrenschmidt
Linus Torvalds
David S. Miller
Alan Cox
Bartlomiej Zolnierkiewicz
Dominik Brodowski
Hemant Pedanekar
H Hartley Sweeten
Robert Hancock
Borislav Petkov
Sergei Shtylyov
Mikulas Patocka
Shane Huang
Marcin Slusarz
Alexey Dobriyan
Joe Perches
Len Brown
Wu Zhangjin
Bob Moore
Sergey Matyukevich
Kevin Hilman
Wolfram Sang
Jaswinder Singh Rajput
Julia Lawall
Borislav Petkov
Mark de Wever
Jean Delvare
Michael Buesch
Maxime Bizon
Christian Engelmayer
Frans Pop
Rainer Weikusat
Greg Kroah-Hartman
Joao Ramos
Pavel Machek
Martin Olsson
Hugh Dickins
Martin K. Petersen
Jens Axboe
Harald Welte
Tejun Heo
Anton Vorontsov