- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCY1kNmwAKCRCKwlD9ZEnx
cHGMAP90gnxw9QtkoODnLu2MbcdNNoB/AFeY4O6snbGcwJTYEQD9GqBXxZ3rhZtR
t34KBpENqFdv5HByIxKQ0OT+yYRZew0=
=oXTL
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-fixes-for-v6.1-tag1'
clk: renesas: Fixes for v6.1
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
Currently, determine_rate() is not doing any round operation
and due to this it always selects a lower clock source compared
to the closest higher one.
Support sd clk mux round operation by passing
CLK_MUX_ROUND_CLOSEST flag to clk_mux_determine_rate_flags().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220919084110.3065156-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IIC groups clock and reset entries to CPG driver.
IIC Group A consists of IIC0 and IIC1. IIC Group B consists of
IIC2 and IIC3. To confuse things, IIC_PCLK0 is used by group A
and IIC_PCLK1 is used by group B.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220819193944.337599-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add conditional compilation for struct r9a07g044_cpg_info, so the
compiler won't allocate any memory for this variable in case
CONFIG_CLK_R9A07G044 is disabled.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220804082605.157269-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A variable pointing to const isn't const itself. It'd have to contain
"const" keyword after "*" too. Therefore, cpg_pll_config cannot be put
to "rodata". Hence use __initdata instead of __initconst to fix this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[js] more explanatory commit message.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220623083217.26433-2-jslaby@suse.cz
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/Five SoC has almost the same clock structure compared to the
Renesas RZ/G2UL SoC, re-use the r9a07g043-cpg.c file to add support for
RZ/Five SoC.
This patch splits up the clocks and reset arrays for RZ/G2UL and RZ/Five
SoC using #ifdef CONFIG_ARM64 and #ifdef CONFIG_RISCV checks.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220622181723.13033-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The register block base pointer as stored in the reg member of the
rz_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
rz_cpg_register_clock().
After this, the data member is the only remaining member of the rz_cpg
structure, so the whole structure can be replaced by the data member.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2380285576edaa4ad3dc5eca7e0ca418f068c6ef.1654694831.git.geert+renesas@glider.be
All but the data member of the r8a7778_cpg structure are unused, so the
whole structure can be replaced by the single member used.
Remove the mapping of the CPG registers, as no code uses the mapped
registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/4123c1c40a901195f00a825d434553d2052829aa.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
sh73a0_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
sh73a0_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5423e43d0cf518691965412fb510097d23ac5955.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a7740_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a7740_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7ec676bcc36ef1eda02c2db328c527fc5fd44e99.1654694831.git.geert+renesas@glider.be
The register block base pointer as stored in the reg member of the
r8a73a4_cpg structure is only used during initialization. Hence move
it to a local variable, and pass it as a parameter to
r8a73a4_cpg_register_clock().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f835f3dfcf3bf754065e5002663952cc6341caac.1654694831.git.geert+renesas@glider.be
As per RZ/G2L HW(Rev.1.10) manual, reset monitor register value 0 means
reset signal is not applied (deassert state) and 1 means reset signal
is applied (assert state).
reset_control_status() expects a positive value if the reset line is
asserted. But rzg2l_cpg_status function returns zero for asserted
state.
This patch fixes the issue by adding double inverted logic, so that
reset_control_status returns a positive value if the reset line is
asserted.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220531071657.104121-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220518182527.1693156-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New support:
- Tegra gpcdma Driver support
- Qualcomm SM8350, Sm8450 and SC7280 Device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- Deprecate '#dma-channels' & '#dma-requests' bindings
- Driver updates for stm32, ptdma idsx etc
-----BEGIN PGP SIGNATURE-----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=ANxH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
The clock controller device on r9a06g032 takes all the memory range that
is described as being a system controller. This range contains many
different (unrelated?) registers besides the ones belonging to the clock
controller, that can necessitate to be accessed from other peripherals.
For instance, the dmamux registers are there. The dmamux "device" will
be described as a child node of the clock/system controller node, which
means we need the top device driver (the clock controller driver in this
case) to populate its children manually. In case of error when
populating the children, we do not fail the probe on purpose to keep the
clk driver up and running.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-7-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmamux register is located within the system controller.
Without syscon, we need an extra helper in order to give write access to
this register to a dmamux driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-5-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add ethernet clock/reset entries to CPG driver.
Note that the AXI and CHI clocks are both enabled and disabled using
the same register bit.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220504145454.71287-2-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/V2M SoC is very similar to RZ/G2L, though it doesn't have
any CLK_MON registers.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-11-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M doesn't have a matching set of reset monitor regs for each reset
reg like the RZ/G2L. Instead, it has a single CPG_RST_MON reg which has a
single bit per module.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-10-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M SoC doesn't use CLK_MON registers, so make them optional.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-9-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All of the muxes and dividers that can be modified require the HIWORD
flags, so make the macros set them. It won't affect read only muxes and
dividers.
This will make the clock tables a little easier to read, particularly for
new SoCs coming.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-8-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We only ever use ARRAY_SIZE() to populate the number of parents, so
move this into the macro to always detect it automatically. This
also makes the tables of clocks a little simpler.
Similarly for the DEF_SD_MUX macro.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-6-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
M3 clock is sourced from DSI Divider (DSIDIVA * DSIDIVB)
This patch add support for DSI divider clk by combining
DSIDIVA and DSIDIVB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PLL5 generates FOUTPOSTDIV clk and is sourced by LCDC/DSI modules.
The FOUTPOSTDIV is connected to PLL5_4 MUX. Video clock is sourced
from DSI divider which is connected to PLL5_4 MUX.
This patch adds support for generating FOUTPOSTDIV clk.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220430114156.6260-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It needs to be un-gated, but also a reset must be released and an idle
flag should also be disabled.
The driver already supports all these operations, so update the
description of the RTC hclock to fit these requirements.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220421090016.79517-3-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_500 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402074626.25624-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/G2UL is almost identical to RZ/G2L SoC with
fewer IP blocks. The IP blocks such as WDT1, GPT, H264, GPU and POEG are
not present on RZ/G2UL.
This patch adds minimal clock and reset entries required to boot the
system on Renesas RZ/G2UL SMARC EVK and binds it with the RZ/G2L CPG core
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Describe the various clocks used by the SPI Multi I/O Bus Controller
(RPC-IF) on the R-Car D3 SoC: RPCSRC internal clock, RPC{,D2} clocks
derived from it, and RPC-IF module clock.
The RPCSRC clock divider on R-Car D3 is very similar to the one on R-Car
E3, but uses a different pre-divider for the PLL0 parent. Add a new
macro to describe it, reusing the existing clock type for R-Car E3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3fd1e886b7737cd0e199603bae81d01be9dcf3aa.1648546700.git.geert+renesas@glider.be
Add the module clock used by the RCLK Watchdog Timer (RWDT) on the
Renesas R-Car S4-8 (r8a779f0) SoC. Mark it as a critical clock, to
ensure uninterrupted watchdog operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8d9b280065a663f2cf31db7b21a010aa781a0af1.1642525158.git.geert+renesas@glider.be
According to Section 8.1.2 Figure 8.1.1 ("Block Diagram of CPG"), Note
22 ("RSW2 divider"), and Table 8.1.4d ("Lists of CPG clocks generated
from CPGMA1"), the RSwitch2 and PCI Express clock is generated from PLL5
by dividing by two, followed by the RSW2 divider. As PLL5 runs at 3200
MHz, and RSW2 is fixed to 320 MHz, the RSW2 divider must be 5.
Correct the parent and the fixed divider.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d6a406f31e6f02f892e0253f4e8a9a2f68fd652e.1641566003.git.geert+renesas@glider.be
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the HW manual (Rev.1.00 Sep, 2021) PLL2 and PLL3 should be
1600 MHz, but with current multiplier and divider values this resulted
to 1596 MHz.
This patch updates the multiplier and divider values for PLL2 and PLL3
so that we get the exact (1600 MHz) values.
Fixes: 17f0ff3d49 ("clk: renesas: Add support for R9A07G044 SoC")
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211223093223.4725-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks for MLP modules on Renesas R-Car E3 and D3 SoCs.
Similar to other R-Car Gen3 SoC, exact information on the parents of MLP
clocks on E3 and D3 is not available. However, since the parents of
these clocks are not anyhow software-controllable, the only harm from
this is inexact information exported via debugfs. So just keep the
parent set in the same way as with other Gen3 SoCs.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211225193957.2195012-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven
Biju Das
Yoshihiro Shimoda
Lad Prabhakar
Wolfram Sang
Phil Edworthy
Andi Kleen
Ralph Siemsen
Linus Torvalds
Miquel Raynal
Ulrich Hecht
Nikita Yushchenko