The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.
The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.
If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.
This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.
Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prefix all internal functions and variables with atmel_ instead of
at91_.
The at91_register_uart_fns() stuff is left as is since I can't find
any actual users of it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename
it atmel_usart.h. Also delete AVR32's version of this file.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
Russell King pointed out that asm/serial.h is anachronistic and we were
misusing BASE_BAUD. So fix BASE_BAUD for PCI 16550 UARTs, move LASI_BASE_BAUD
into 8250_gsc, and fix the obsolete comment about reserving serial port slots.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Compaq TC1000 and Fujitsu Stylistic range of tablet machines use
touchscreens from FPI. These are implemented as serial interfaces,
generally exposed in the ACPIPNP information on the system. This patch
adds them to the 8250_pnp driver tables, avoiding the need to mess
around with setserial to set them up.
I haven't been able to confirm what FUJ02B5, FUJ02BA and FUJ02BB are.
FUJ02B1 refers to the controller for the system hotkeys. FUJ02BC appears
to be the last in the range - after this, they moved to Wacom-based
systems.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Serial is _slow_ sometimes. So slow, that the NMI watchdog kicks in.
NMI Watchdog detected LOCKUP on CPU2CPU 2
Modules linked in: loop usb_storage md5 ipv6 parport_pc lp parport autofs4 i2c_dev i2c_core rfcomm l2cap bluetooth sunrpc pcdPid: 3138, comm: gpm Not tainted 2.6.11-1.1290_FC4smp
RIP: 0010:[<ffffffff80273b8a>] <ffffffff80273b8a>{serial_in+106}
RSP: 0018:ffff81003afc3d50 EFLAGS: 00000002
RAX: 0000000000000020 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff804dcd60
RBP: 00000000000024fc R08: 000000000000000a R09: 0000000000000033
R10: ffff81001beb7c20 R11: 0000000000000020 R12: ffffffff804dcd60
R13: ffffffff804ade76 R14: 000000000000002b R15: 000000000000002c
FS: 00002aaaaaac4920(0000) GS:ffffffff804fca00(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002aaaaabcb000 CR3: 000000003c0d0000 CR4: 00000000000006e0
Process gpm (pid: 3138, threadinfo ffff81003afc2000, task ffff81003eb63780)
Stack: ffffffff80275f2e 0000000000000000 ffffffff80448380 0000000000007d6b
000000000000002c fffffffffffffbbf 0000000000000292 0000000000008000
ffffffff80138e8c 0000000000007d97
Call Trace:<ffffffff80275f2e>{serial8250_console_write+270} <ffffffff80138e8c>{__call_console_drivers+76}
<ffffffff8013914b>{release_console_sem+315} <ffffffff80260325>{con_open+149}
<ffffffff80254e99>{tty_open+537} <ffffffff80192713>{chrdev_open+387}
<ffffffff80188824>{dentry_open+260} <ffffffff80188994>{filp_open+68}
<ffffffff80187b73>{get_unused_fd+227} <ffffffff80188a6c>{sys_open+76}
<ffffffff8010ebc6>{tracesys+209}
Code: 0f b6 c0 c3 66 90 41 57 49 89 f7 41 56 41 be 00 01 00 00 41
console shuts up ...
I initially did the patch below a year ago for the Fedora kernel, and have
been keeping it up to date since. I recently got the same thing happening
on a vanilla kernel, so figured it was time to repost this.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, pcmcia_dev_present() returns false when a device is
suspended, so checking this on resume does not work too well. Omit
this test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below is necessary for 115200 baud on an OMAP1510 internal UART.
It's been in the linux-omap tree for some time and with it applied to a
vanilla Linus git tree the serial console on the Amstrad Delta (which is
OMAP1510 based and whose initial bootloader runs at 115200) works fine (it
doesn't without it).
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the issue of returning 0 even in case of error from uart_set_info
function. Now it returns the error EBUSY when it can not set new port.
Signed-off-by: Ram Gupta <r.gupta@astronautics.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/proc/tty/driver/serial incorrectly claims that UARTs having iotype of
UPIO_MEM32, UPIO_AU, or UPIO_TSI are I/O mapped.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
8250.c and serial_txx9.c port suspend/resume handler still have this obsolete
argument documented...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I think register ranges obviously need to be claimed/released for all UARTs
including those with UPIO_MEM32 and UPIO_TSI iotype.
Also, serial8250_request_rsa_resources() returns false positives with
UPIO_MEM32, UPIO_AU, and UPIO_TSI iotype -- I don't think this makes any sense.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mauro Ziliani reports that this card has a higher clock rate.
Rather than tweak the 8250 driver to handle this, add a quirk to
pass the correct clock rate to the driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the existing code, Nokia only make single-port cards,
but are detected as multi-port cards. Handle this in roughly the
same way via the config quirk - forcing it to be a real single port
card (info->multi=0) changes the way we allocate the IO memory,
which might stop the card working.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a quirk primerily to handle tweaks to the link->conf structure,
eg as required for Socket cards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move IBM quirk handling into its own quirk entry. Note that doing
quirk handling after we've registered the ports is racy, but since
I don't know if moving this will have an undesired effect, it's
probably better to leave where it is.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some quirks we will introduce next apply to (eg) all cards of one
manufacturer. Therefore, we need a way to list these in the quirk
table - use ~0 - this is not a possible device ID value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- rename multi_id table to serial_quirk / quirks[]
- use named initialisers
- store a pointer to the quirk table in the serial_info structure
so we can use the quirk table entry later.
- apply multi-port quirk after the multi-port guessing code,
but only if it's != -1.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Use ARRAY_SIZE() instead of home grown based version.
- use parse->manfid.card rather than le16_to_cpu(buf[1]) -
manfid.card is already converted to this format.
- use info->prodid in subsequent tests rather than
parse->manfid.card.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
m32r_sio re-uses a custom defined BASE_BAUD from asm/serial.h,
and replaces SERIAL_PORT_DFNS with its own driver private copy.
Since asm/serial.h is supposed to define 8250-based ports using
these symbols, this isn't a sane idea.
Hence, eliminate asm/serial.h from m32r_sio.c.
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David S. Miller <davem@sunset.davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the Kconfig entry for console on AMBA PL011 to match the code.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Haavard Skinnemoen
Linus Torvalds
Matthew Wilcox
Carlos O'Donell
Dave Jones
Uwe Zeisberger
Matt LaPlante
Jeff Dike
Matthew Garrett
Russell King
Alexey Dobriyan
Jonathan McDowell
Ram Gupta
Sergei Shtylyov
Amol Lad
David S. Miller
Peter Korsgaard