To have the detailed property on each PHY specifier, this patch revises
the #phy-cells property.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document RZ/G1C (R8A77470) SoC bindings.
For RZ/G1C, this driver is used to enable interrupt generation and
initializing timing registers which is part of phy_init code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB PHY support for r8a77470 SoC. Renesas RZ/G1C (R8A77470)
USB PHY is similar to the R-Car Gen2 family, but has the below
feature compared to other RZ/G1 and R-Car Gen2/3 SoCs
It has a shared pll reset for usbphy0/usbphy1 and this register
reside in usbphy0 block.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add UFS M-PHY node document for MediaTek SoC chips.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch documents the new proprty drive-impedance-ohm for
Rockchip's eMMC PHY node.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a resets property to the PHY that represents the PHY reset
register in the UFS controller itself. This better describes the
complete specification of the PHY, and allows the PHY to perform
its initialization in a single function, rather than relying on
back-channel sequencing of initialization through the PHY framework.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a required reset to the SDM845 UFS phy to express the PHY reset
bit inside the UFS controller register space. Before this change, this
reset was not expressed in the DT, and the driver utilized two different
callbacks (phy_init and phy_poweron) to implement a two-phase
initialization procedure that involved deasserting this reset between
init and poweron. This abused the two callbacks and diluted their
purpose.
That scheme does not work as regulators cannot be turned off in
phy_poweroff because they were turned on in init, rather than poweron.
The net result is that regulators are left on in suspend that shouldn't
be.
This new scheme gives the UFS reset to the PHY, so that it can fully
initialize itself in a single callback. We can then turn regulators on
during poweron and off during poweroff.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable Qualcomm UFS controllers to expose the PHY reset via a reset
controller.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the Amlogic G12A Family USB3 + PCIE Combo PHY Bindings.
This PHY can provide exclusively USB3 or PCIE support on shared I/Os.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the Amlogic G12A Family USB2 OTG PHY Bindings
The PHY can work in host or peripheral modes depending on it's position.
Configuration of the mode is part of the USBCTRL registers which are
outside of the PHY registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT binding document for Stingray USB PHY.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Extend the bindings to cover the set of features found in Tegra186. Note
that, technically, there are four more supplies connected to the XUSB
pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
the power sequencing requirements of Tegra186 require these to be under
the control of the PMIC.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+ZFI
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.1' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Just a couple of small fixes and cleanups:
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)"
* tag 'fbdev-v5.1' of git://github.com/bzolnier/linux:
fbdev: mbx: fix a misspelled variable name
fbdev: omap2: fix warnings in dss core
video: fbdev: Fix potential NULL pointer dereference
fbcon: Silence fbcon logo on 'quiet' boots
printk: Export console_printk
ARM: dts: imx28-cfa10036: Fix the reset gpio signal polarity
video: ssd1307fb: Do not hard code active-low reset sequence
dt-bindings: display: ssd1307fb: Remove reset-active-low from examples
fbdev: fbmem: fix memory access if logo is bigger than the screen
video/fbdev: refactor video= cmdline parsing
fbdev: mbx: fix up debugfs file creation
fbdev: omap2: no need to check return value of debugfs_create functions
video: fbdev: geode: remove ifdef OLPC noise
video: offb: annotate implicit fall throughs
omapfb: fix typo
fbdev: Use of_node_name_eq for node name comparisons
fbcon: use kvmalloc() for scrollback buffer
fbdev: chipsfb: remove set but not used variable 'size'
fbdev/via: fix spelling mistake "Expandsion" -> "Expansion"
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs.
-----BEGIN PGP SIGNATURE-----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=4xC9
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.1' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs"
* tag 'rproc-v5.1' of git://github.com/andersson/remoteproc: (33 commits)
remoteproc: fix for "dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag"
remoteproc: fix rproc_check_carveout_da() returned error and comments
remoteproc: fix trace buffer va initialization
remoteproc: fix rproc_alloc_carveout() for rproc with iommu domain
remoteproc: add warning on resource table cast
remoteproc: fix rproc_alloc_carveout() bad variable cast
remoteproc: fix rproc_da_to_va in case of unallocated carveout
remoteproc: correct rproc_mem_entry_init() comments
remoteproc: fix recovery procedure
rpmsg: virtio: change header file sort style
rpmsg: virtio: allocate buffer from parent
remoteproc: st: add reserved memory support
remoteproc: create vdev subdevice with specific dma memory pool
remoteproc: q6v5_adsp: Remove voting for lpass_aon clock
dt-binding: remoteproc: Remove lpass_aon clock from adsp pil clock list
remoteproc: q6v5-mss: Active powerdomain for SDM845
remoteproc: q6v5-mss: Vote for rpmh power domains
remoteproc: qcom: Add support for parsing fw dt bindings
remoteproc: qcom_q6v5: don't auto boot remote processor
remoteproc: qcom: Wait for shutdown-ack/ind on sysmon shutdown
...
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
The changes for this cycle are across the board. The bulk of it is
cleanups, but there's also new device support in some drivers as well as
more conversions to the atomic API.
-----BEGIN PGP SIGNATURE-----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=TyJJ
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this cycle are across the board.
The bulk of it is cleanups, but there's also new device support in
some drivers as well as more conversions to the atomic API"
* tag 'pwm/for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: atmel: Remove useless symbolic definitions
pwm: bcm-kona: Update macros to remove braces around numbers
pwm: imx27: Only enable the clocks once in .get_state()
pwm: rcar: Improve calculation of divider
pwm: rcar: Remove legacy APIs
pwm: rcar: Use "atomic" API on rcar_pwm_resume()
pwm: rcar: Add support "atomic" API
pwm: atmel: Add support for SAM9X60's PWM controller
pwm: atmel: Add PWM binding for SAM9X60
pwm: atmel: Rename objects of type atmel_pwm_data
pwm: atmel: Add support for controllers with 32 bit counters
pwm: atmel: Add struct atmel_pwm_data
pwm: Add MediaTek MT8183 display PWM driver support
pwm: hibvt: Add hi3559v100 support
dt-bindings: pwm: hibvt: Add hi3559v100 support
pwm: hibvt: Use individual struct per of-data
pwm: imx: Signedness bug in imx_pwm_get_state()
pwm: imx: Split into two drivers
pwm: imx: Don't print an error on -EPROBE_DEFER
pwm: imx: Set driver data earlier simplifying the end of ->probe()
...
Add documentation for a new optional property local-mac-address which
is described in ethernet.txt.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
Pull networking fixes from David Miller:
"First batch of fixes in the new merge window:
1) Double dst_cache free in act_tunnel_key, from Wenxu.
2) Avoid NULL deref in IN_DEV_MFORWARD() by failing early in the
ip_route_input_rcu() path, from Paolo Abeni.
3) Fix appletalk compile regression, from Arnd Bergmann.
4) If SLAB objects reach the TCP sendpage method we are in serious
trouble, so put a debugging check there. From Vasily Averin.
5) Memory leak in hsr layer, from Mao Wenan.
6) Only test GSO type on GSO packets, from Willem de Bruijn.
7) Fix crash in xsk_diag_put_umem(), from Eric Dumazet.
8) Fix VNIC mailbox length in nfp, from Dirk van der Merwe.
9) Fix race in ipv4 route exception handling, from Xin Long.
10) Missing DMA memory barrier in hns3 driver, from Jian Shen.
11) Use after free in __tcf_chain_put(), from Vlad Buslov.
12) Handle inet_csk_reqsk_queue_add() failures, from Guillaume Nault.
13) Return value correction when ip_mc_may_pull() fails, from Eric
Dumazet.
14) Use after free in x25_device_event(), also from Eric"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
gro_cells: make sure device is up in gro_cells_receive()
vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()
net/x25: fix use-after-free in x25_device_event()
isdn: mISDNinfineon: fix potential NULL pointer dereference
net: hns3: fix to stop multiple HNS reset due to the AER changes
ip: fix ip_mc_may_pull() return value
net: keep refcount warning in reqsk_free()
net: stmmac: Avoid one more sometimes uninitialized Clang warning
net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
rxrpc: Fix client call queueing, waiting for channel
tcp: handle inet_csk_reqsk_queue_add() failures
net: ethernet: sun: Zero initialize class in default case in niu_add_ethtool_tcam_entry
8139too : Add support for U.S. Robotics USR997901A 10/100 Cardbus NIC
fou, fou6: avoid uninit-value in gue_err() and gue6_err()
net: sched: fix potential use-after-free in __tcf_chain_put()
vhost: silence an unused-variable warning
vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock
connector: fix unsafe usage of ->real_parent
vxlan: do not need BH again in vxlan_cleanup()
net: hns3: add dma_rmb() for rx description
...
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
Including:
- A big cleanup and optimization patch-set for the
Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and
Intel VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some
aliased devices, needed for future devices which send IRQ
messages from more than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable
outside of the IOMMU code
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEr9jSbILcajRFYWYyK/BELZcBGuMFAlyCNlIACgkQK/BELZcB
GuNDiRAAscgYj0BdqpZVUNHl4PySR12QJpS1myl/OC4HEbdB/EOh+bYT4Q1vptCU
GNK6Gt9SVfcbtWrLiGfcP9ODXmbqZ6AIOIbHKv9cvw1mnyYAtVvT/kck7B/W5jEr
/aP/5RTO7XcqscWO44zBkrtLFupegtpQFB0jXYTJYTrwQoNKRqCUqfetZGzMkXjL
x/h7kFTTIRcVP8RFcOeAMwC6EieaI8z8HN976Gu7xSV8g0VJqoNsBN8jbUuBh5AN
oPyd9nl1KBcIQEC1HsbN8I5wIhTh1sJ2UDqFHAgtlnO59zWHORuFUUt6SXbC9UqJ
okJTzFp9Dh2BqmFPXxBTxAf3j+eJP2XPpDI9Ask6SytEPhgw39fdlOOn2MWfSFoW
TaBJ4ww/r98GzVxCP7Up98xFZuHGDICL3/M7Mk3mRac/lgbNRbtfcBa5NV4fyQhY
184t656Zm/9gdWgGAvYQtApr6/iI+wRMLkIwuw63wqH09yfbDcpTOo6DEQE3B5KR
4H1qSIiVGVVZlWQateR6N32ZmY4dWzpnL2b8CfsdBytzHHFb/c3dPnZB8fxx9mwF
onyvjg9nkIiv7mdcN4Ox2WXrAExTeSftyPajN0WWawNJU3uPTBgNrqNHyWSkiaN4
dAvEepfGuFQGz2Fj03Pv7OqY8veyRezErVRLwiMJRNyy7pi6Wng=
=cKsD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- A big cleanup and optimization patch-set for the Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and Intel
VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some aliased
devices, needed for future devices which send IRQ messages from more
than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable outside of
the IOMMU code
- Various other small fixes and cleanups
* tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Get domain ID before clear pasid entry
iommu/vt-d: Fix NULL pointer reference in intel_svm_bind_mm()
iommu/vt-d: Set context field after value initialized
iommu/vt-d: Disable ATS support on untrusted devices
iommu/mediatek: Fix semicolon code style issue
MAINTAINERS: Add Hyper-V IOMMU driver into Hyper-V CORE AND DRIVERS scope
iommu/hyper-v: Add Hyper-V stub IOMMU driver
x86/Hyper-V: Set x2apic destination mode to physical when x2apic is available
PCI/ATS: Add inline to pci_prg_resp_pasid_required()
iommu/vt-d: Check identity map for hot-added devices
iommu: Fix IOMMU debugfs fallout
iommu: Document iommu_ops.is_attach_deferred()
iommu: Document iommu_ops.iotlb_sync_map()
iommu/vt-d: Enable ATS only if the device uses page aligned address.
PCI/ATS: Add pci_ats_page_aligned() interface
iommu/vt-d: Fix PRI/PASID dependency issue.
PCI/ATS: Add pci_prg_resp_pasid_required() interface.
iommu/vt-d: Allow interrupts from the entire bus for aliased devices
iommu/vt-d: Add helper to set an IRTE to verify only the bus number
iommu: Fix flush_tlb_all typo
...
- Fix a unittest failure on UML. Preparation for converting to
kunit test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that
needs it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
-----BEGIN PGP SIGNATURE-----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=CnTd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix a unittest failure on UML. Preparation for converting to kunit
test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that needs
it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: unittest: unflatten device tree on UML when testing
dt-bindings: Add vendor prefix for feiyang
dt-bindings: Add vendor prefix for techstar
dt-bindings: display: add missing semicolon in example
of: mark early_init_dt_alloc_reserved_memory_arch static
of: add dtc annotations functionality to dtx_diff
of: unittest: add caution to function header comment
of: unittest: remove report of expected error
dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
dt-bindings: arm: l2x0: Convert L2 cache to json-schema
media: s5p-mfc: Fix memdev DMA configuration
dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by the
riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception level
and to avoid the propagation of the UNKNOWN FAR value into the si_code
for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
-----BEGIN PGP SIGNATURE-----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=2U56
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by
the riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception
level and to avoid the propagation of the UNKNOWN FAR value into the
si_code for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
arm64: mmu: drop paging_init comments
arm64: debug: Ensure debug handlers check triggering exception level
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
Revert "arm64: uaccess: Implement unsafe accessors"
arm64: avoid clang warning about self-assignment
arm64: Kconfig.platforms: fix warning unmet direct dependencies
lib/raid6: arm: optimize away a mask operation in NEON recovery routine
lib/raid6: use vdupq_n_u8 to avoid endianness warnings
arm64: io: Hook up __io_par() for inX() ordering
riscv: io: Update __io_[p]ar() macros to take an argument
asm-generic/io: Pass result of I/O accessor to __io_[p]ar()
arm64: Add workaround for Fujitsu A64FX erratum 010001
arm64: Rename get_thread_info()
arm64: Remove documentation about TIF_USEDFPU
arm64: irqflags: Fix clang build warnings
arm64: Enable the support of pseudo-NMIs
arm64: Skip irqflags tracing for NMI in IRQs disabled context
arm64: Skip preemption when exiting an NMI
arm64: Handle serror in NMI context
irqchip/gic-v3: Allow interrupts to be set as pseudo-NMI
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
-----BEGIN PGP SIGNATURE-----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=tD1x
-----END PGP SIGNATURE-----
Merge tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove sensor drivers that got converted from soc_camera
- remaining soc_camera drivers got moved to staging
- some documentation cleanups and improvements
- the imx staging driver now supports imx7
- the ov9640, mt9m001 and mt9m111 got converted from soc_camera
- the vim2m driver now does what a m2m convert driver expects to do
- epoll() fixes on media subsystems
- several drivers fixes, typos, cleanups and improvements
* tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (346 commits)
media: dvb/earth-pt1: fix wrong initialization for demod blocks
media: vim2m: Address some coding style issues
media: vim2m: don't use BUG()
media: vim2m: speedup passthrough copy
media: vim2m: add an horizontal scaler
media: vim2m: don't accept YUYV anymore as output format
media: vim2m: add vertical linear scaler
media: vim2m: better handle cap/out buffers with different sizes
media: vim2m: use different framesizes for bayer formats
media: vim2m: add support for VIDIOC_ENUM_FRAMESIZES
media: vim2m: ensure that width is multiple of two
media: vim2m: improve debug messages
media: vim2m: add bayer capture formats
media: a few more typos at staging, pci, platform, radio and usb
media: Documentation: fix several typos
media: staging: fix several typos
media: include: fix several typos
media: common: fix several typos
media: v4l2-core: fix several typos
media: usb: fix several typos
...
Add properties to support all Phy config
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
Subsystem:
- new quartz-load-femtofarads DT property for quartz load capacitance
- remove rtc_class_ops.read_callback
New drivers:
- Abracon AB-RTCMC-32.768kHz-EOZ9
- Amlogic Meson RTC
- Cadence RTC IP
- Microcrystal RV3028
- Whwave sd3078
Drivers:
- cmos: ignore bogus century byte
- ds1307: rework rx8130 support
- isl1208: add isl1209 support, nvmem support
- rs5C372: report invalid time when the oscillator stopped
- rx8581: add rx8571 support
-----BEGIN PGP SIGNATURE-----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=/Noj
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is an unusual amount of new drivers this cycle, and this
explains the number of insertions.
Other than that, the changes are the usual fixes and feature addition.
Subsystem updates:
- new quartz-load-femtofarads DT property for quartz load capacitance
- remove rtc_class_ops.read_callback
New drivers:
- Abracon AB-RTCMC-32.768kHz-EOZ9
- Amlogic Meson RTC
- Cadence RTC IP
- Microcrystal RV3028
- Whwave sd3078
Driver updates:
- cmos: ignore bogus century byte
- ds1307: rework rx8130 support
- isl1208: add isl1209 support, nvmem support
- rs5C372: report invalid time when the oscillator stopped
- rx8581: add rx8571 support"
* tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (66 commits)
rtc: pic32: convert to SPDX identifier
rtc: pic32: let the core handle range
rtc: pic32: convert to devm_rtc_allocate_device
rtc: update my email address
rtc: rv8803: convert to SPDX identifier
rtc: rv8803: let the core handle range
rtc: tx4939: convert to SPDX identifier
rtc: tx4939: use .set_time
rtc: tx4939: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: tx4939: set range
rtc: tx4939: remove useless test
rtc: zynqmp: let the core handle range
rtc: zynqmp: fix possible race condition
rtc: imx-sc: use rtc_time64_to_tm
rtc: rx8581: Add support for Epson rx8571 RTC
dt-bindings: rtc: add rx8571 compatible
rtc: pcf85063: remove dead code
rtc: remove rtc_class_ops.read_callback
rtc: add AB-RTCMC-32.768kHz-EOZ9 RTC support
dt-bindings: rtc: add ABEOZ9
...
Pull thermal soc updates from Eduardo Valentin:
"Specifics:
- mediatek thermal now supports MT8183
- broadcom thermal now supports Stingray
- qoirq now supports multiple sensors
- fixes on different drivers: rcar, tsens, tegra
Some new drivers are still pending further review and I chose to leave
them for the next merge window while still sending this material"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: rcar_gen3_thermal: Register hwmon sysfs interface
thermal/qcom/tsens-common : fix possible object reference leak
thermal: tegra: add get_trend ops
thermal: tegra: fix memory allocation
thermal: tegra: remove unnecessary warnings
thermal: mediatek: add support for MT8183
dt-bindings: thermal: add binding document for mt8183 thermal controller
thermal: mediatek: add flag for bank selection
thermal: mediatek: add thermal controller offset
thermal: mediatek: add calibration item
thermal: mediatek: add common index of vts settings.
thermal: mediatek: fix register index error
thermal: qoriq: add multiple sensors support
thermal: broadcom: Add Stingray thermal driver
dt-bindings: thermal: Add binding document for SR thermal
Pull i2c updates from Wolfram Sang:
- the I2C core gained helpers to assist drivers in handling their
suspended state, and drivers were converted to use it
- two new fault-injectors for stress-testing
- bigger refactoring and feature improvements for the ocores,
sh_mobile, and tegra drivers
- platform_data removal for the at24 EEPROM driver
- ... and various improvements and bugfixes all over the subsystem
* 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
i2c: Allow recovery of the initial IRQ by an I2C client device.
i2c: ocores: turn incomplete kdoc into a comment
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended
i2c: tegra: Only display error messages if DMA setup fails
i2c: gpio: fault-injector: add 'inject_panic' injector
i2c: gpio: fault-injector: add 'lose_arbitration' injector
i2c: tegra: remove multi-master support
i2c: tegra: remove master fifo support on tegra186
i2c: tegra: change phrasing, "fallbacking" to "falling back"
i2c: expand minor range when registering chrdev region
i2c: aspeed: Add multi-master use case support
i2c: core-smbus: don't trace smbus_reply data on errors
i2c: ocores: Add support for bus clock via platform data
i2c: ocores: Add support for IO mapper registers.
i2c: ocores: checkpatch fixes
i2c: ocores: add SPDX tag
i2c: ocores: add polling interface
i2c: ocores: do not handle IRQ if IF is not set
i2c: ocores: stop transfer on timeout
i2c: tegra: add i2c interface timing support
...
* at91-reset: add sam9x60 support
* sc27xx: improve capacity logic
* goldfish_battery: enhance driver by adding many new properties
* isp1704: drop platform data and migrate to gpiod
* misc. small fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAlx+8LYACgkQ2O7X88g7
+prQew//RFv4KDosWXjxJ+2FgjYke8sjwf8oRN6CD2PyYdX0JY8O4fIucqGn6w+d
Xvw/JBTpV+e3J8C0ZEYC7eN3wbgFh+pBI1TYa+gepMLsgv/uqGCuBGQPJoddkiLy
AjTIDITBMDBJonQEmuxMxbA+FmnJ0FxLKOl6EInesDIU1UiEiMsmkDRU9gj88PQQ
DplsADjw8L5ktGvjfj11HY/iTAaJwSPa3X0jhpBpiR6zJs2iqN4JHYunoTm7ss+i
NSh19haS5E1yifRMmF8QTHXZB4KmaNGNSL2MFU7fwTP+tkZpn/MjWlTE57IuzT8v
MIGVoXZMsvWDIaMc9SRnYaQ2rFD+A3Z8fkXm5KYZdjvNtDe2y7R+omWjAaHHUOME
Nctj0qY4UcS4820LnZUsg8txsu7oDTpnh4GST5w9rBGtYqWrdAZ+B8e/a8bqO1Rt
2mUQdjIGSKzzamBJDswY26gFm0VozwND3WE8aKNFfFK2M6kkM1vqmqpV/QIpjBOY
QzhbGf3vMJbqfwmyrBbmkLbjlY02XAmxM7h0wlwVLg2vGz/9LOf5ilpdHu2YxLHL
OXB+RMQudgDou665Gc55PD5NwpJQGU2vImxIHjPUYrYOOwVfDci2MWyxxiFL+bEd
Bk62pNOVmsPmXkRXp8+1e02nta/dwtle1oTGFtqRN7v3RynMTM4=
=Etl6
-----END PGP SIGNATURE-----
Merge tag 'for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Nothing too fancy in the power-supply subsystem this time. There are
less patches than usual, since I did not have enough time to review
them in time. The good news is, that all patches have been in
linux-next for more than two weeks and there are no complicated
cross-subsystem patchsets this time!
Summary:
- at91-reset: add sam9x60 support
- sc27xx: improve capacity logic
- goldfish_battery: enhance driver by adding many new properties
- isp1704: drop platform data and migrate to gpiod
- misc small fixes and improvements"
* tag 'for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (25 commits)
power: reset: at91-reset: add support for sam9x60 SoC
dt-bindings: arm: atmel: add new sam9x60 reset controller binding
dt-bindings: arm: atmel: add missing samx7 to reset controller
max17042_battery: fix potential use-after-free on device remove
power: supply: core: Add a field to support battery max voltage
dt-bindings: power: supply: Add voltage-max-design-microvolt property
bq27x00: use cached flags
power: supply: ds2782: fix possible use-after-free on remove
power: supply: bq25890: show max charge current/voltage as configured
power: supply: sc27xx: Fix capacity saving function
power: supply: sc27xx: Fix the incorrect formula when converting capacity to coulomb counter
power: supply: sc27xx: Add one property to read charge voltage
dt-bindings: power: sc27xx: Add one IIO channel to read charge voltage
drivers: power: supply: goldfish_battery: Add support for reading more properties
power: supply: charger-manager: Fix trivial language typos
cpcap-charger: generate events for userspace
power: supply: remove some duplicated includes
power: twl4030: fix a missing check of return value
drivers: power: supply: goldfish_battery: Use tabs for alignment
drivers: power: supply: goldfish_battery: Fix alignment
...
* New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck)
* Altera SDRAM functionality carveout for separate enablement of RAS and
SDRAM capabilities on some Altera chips. (Thor Thayer)
* The usual round of cleanups and fixes
Last but not least:
* Recruit James Morse as a reviewer for the ARM side
-----BEGIN PGP SIGNATURE-----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=A1kA
-----END PGP SIGNATURE-----
Merge tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- A new EDAC AST 2500 SoC driver (Stefan M Schaeckeler)
- New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck)
- Altera SDRAM functionality carveout for separate enablement of RAS
and SDRAM capabilities on some Altera chips. (Thor Thayer)
- The usual round of cleanups and fixes
And last but not least: recruit James Morse as a reviewer for the ARM
side.
* tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC/altera: Add separate SDRAM EDAC config
EDAC, altera: Add missing of_node_put()
EDAC, skx_common: Add code to recognise new compound error code
EDAC, i10nm: Fix randconfig builds
EDAC, i10nm: Add a driver for Intel 10nm server processors
EDAC, skx_edac: Delete duplicated code
EDAC, skx_common: Separate common code out from skx_edac
EDAC: Do not check return value of debugfs_create() functions
EDAC: Add James Morse as a reviewer
dt-bindings, EDAC: Add Aspeed AST2500
EDAC, aspeed: Add an Aspeed AST2500 EDAC driver
Yoshihiro Shimoda
Biju Das
Stanley Chu
Christoph Muellner
Evan Green
Neil Armstrong
Srinath Mannam
Thierry Reding
Linus Torvalds
Vinod Koul
xiaofeis
Christophe Roullier
Stephen Boyd