Some gcc versions warn about prototypes without "inline" when the declaration
includes the "inline" keyword. The fix generates a false error message
"marked inline, but without a definition" with sparse below 0.4.2.
Signed-off-by: Chris Friesen <chris.friesen@genband.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If overlapping networks with different interfaces was added to
the set, the type did not handle it properly. Example
ipset create test hash:net,iface
ipset add test 192.168.0.0/16,eth0
ipset add test 192.168.0.0/24,eth1
Now, if a packet was sent from 192.168.0.0/24,eth0, the type returned
a match.
In the patch the algorithm is fixed in order to correctly handle
overlapping networks.
Limitation: the same network cannot be stored with more than 64 different
interfaces in a single set.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Non default Drive Strength cannot be set automatically. It is a function
of the board design and only if there is a specific platform handler can
it be set. The platform handler needs to take into account the board
design. Pass to the platform code the necessary information.
For example: The card and host controller may indicate they support HIGH
and LOW drive strength. There is no way to know what should be chosen
without specific board knowledge. Setting HIGH may lead to reflections
and setting LOW may not suffice. There is no mechanism (like ethernet
duplex or speed pulses) to determine what should be done automatically.
If no platform handler is defined -- use the default value.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously there has only been one function mmc_wait_for_req()
to start and wait for a request. This patch adds:
* mmc_start_req() - starts a request wihtout waiting
If there is on ongoing request wait for completion
of that request and start the new one and return.
Does not wait for the new command to complete.
This patch also adds new function members in struct mmc_host_ops
only called from core.c:
* pre_req - asks the host driver to prepare for the next job
* post_req - asks the host driver to clean up after a completed job
The intention is to use pre_req() and post_req() to do cache maintenance
while a request is active. pre_req() can be called while a request is
active to minimize latency to start next job. post_req() can be used after
the next job is started to clean up the request. This will minimize the
host driver request end latency. post_req() is typically used before
ending the block request and handing over the buffer to the block layer.
Add a host-private member in mmc_data to be used by pre_req to mark the
data. The host driver will then check this mark to see if the data is
prepared or not.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.
Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some host controllers will not operate without a hardware
timeout that is limited in value. However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.
A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.
However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change. For that case Preferred Erase Size
is used instead.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.
Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.
Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.
Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reflects at least the current usage of this register
and I think it improves the readability of the code ever so slightly.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the MMC_SEND_STATUS command is not successful, we should not return
a zero status word, but instead allow the caller to know positively
that an error occurred.
Convert the open-coded get_card_status() to use the helper function,
and provide definitions for the card state field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Reduce high order allocations for some setups.
(NR_CPUS=4096 -> we need 64KB per kmem_cache struct)
We now allocate exact needed size (using nr_cpu_ids and nr_node_ids)
This also makes code a bit smaller on x86_64, since some field offsets
are less than the 127 limit :
Before patch :
# size mm/slab.o
text data bss dec hex filename
22605 361665 32 384302 5dd2e mm/slab.o
After patch :
# size mm/slab.o
text data bss dec hex filename
22349 353473 8224 384046 5dc2e mm/slab.o
CC: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Allow for sched_domain spans that overlap by giving such domains their
own sched_group list instead of sharing the sched_groups amongst
each-other.
This is needed for machines with more than 16 nodes, because
sched_domain_node_span() will generate a node mask from the
16 nearest nodes without regard if these masks have any overlap.
Currently sched_domains have a sched_group that maps to their child
sched_domain span, and since there is no overlap we share the
sched_group between the sched_domains of the various CPUs. If however
there is overlap, we would need to link the sched_group list in
different ways for each cpu, and hence sharing isn't possible.
In order to solve this, allocate private sched_groups for each CPU's
sched_domain but have the sched_groups share a sched_group_power
structure such that we can uniquely track the power.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-08bxqw9wis3qti9u5inifh3y@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to prepare for non-unique sched_groups per domain, we need to
carry the cpu_power elsewhere, so put a level of indirection in.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-qkho2byuhe4482fuknss40ad@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The RCU_BOOST commits for TREE_PREEMPT_RCU introduced an other-task
write to a new RCU_READ_UNLOCK_BOOSTED bit in the task_struct structure's
->rcu_read_unlock_special field, but, as noted by Steven Rostedt, without
correctly synchronizing all accesses to ->rcu_read_unlock_special.
This could result in bits in ->rcu_read_unlock_special being spuriously
set and cleared due to conflicting accesses, which in turn could result
in deadlocks between the rcu_node structure's ->lock and the scheduler's
rq and pi locks. These deadlocks would result from RCU incorrectly
believing that the just-ended RCU read-side critical section had been
preempted and/or boosted. If that RCU read-side critical section was
executed with either rq or pi locks held, RCU's ensuing (incorrect)
calls to the scheduler would cause the scheduler to attempt to once
again acquire the rq and pi locks, resulting in deadlock. More complex
deadlock cycles are also possible, involving multiple rq and pi locks
as well as locks from multiple rcu_node structures.
This commit fixes synchronization by creating ->rcu_boosted field in
task_struct that is accessed and modified only when holding the ->lock
in the rcu_node structure on which the task is queued (on that rcu_node
structure's ->blkd_tasks list). This results in tasks accessing only
their own current->rcu_read_unlock_special fields, making unsynchronized
access once again legal, and keeping the rcu_read_unlock() fastpath free
of atomic instructions and memory barriers.
The reason that the rcu_read_unlock() fastpath does not need to access
the new current->rcu_boosted field is that this new field cannot
be non-zero unless the RCU_READ_UNLOCK_BLOCKED bit is set in the
current->rcu_read_unlock_special field. Therefore, rcu_read_unlock()
need only test current->rcu_read_unlock_special: if that is zero, then
current->rcu_boosted must also be zero.
This bug does not affect TINY_PREEMPT_RCU because this implementation
of RCU accesses current->rcu_read_unlock_special with irqs disabled,
thus preventing races on the !SMP systems that TINY_PREEMPT_RCU runs on.
Maybe-reported-by: Dave Jones <davej@redhat.com>
Maybe-reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Introduces a new nfnetlink type that applies a given
verdict to all queued packets with an id <= the id in the verdict
message.
If a mark is provided it is applied to all matched packets.
This reduces the number of verdicts that have to be sent.
Applications that make use of this feature need to maintain
a timeout to send a batchverdict periodically to avoid starvation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move the various definitions and mad structures needed for software
implementation of IBA PM agent from the ipath and qib drivers into a
single include file, which in turn could be used by more consumers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs. Each such counter tracks receive
and transmit packets and bytes of these QPs. This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations. Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the address handle portion of the QP context structure to have the
correct bit location for the counter index field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags. Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability. Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add IB GID change event type. This is needed for IBoE when the HW
driver updates the GID (e.g when new VLANs are added/deleted) table
and the change should be reflected to the IB core cache.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
of_address.h makes reference to some of the error code #defines, so it
needs to include errno.h. If CONFIG_PCI is not selected, then some files
will fail to compile.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
of_find_matching_node_by_address() can be used to find a device tree
node for a device at a specific address.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change adds a procfs connector event, which is emitted on every
successful process tracer attach or detach.
If some process connects to other one, kernelspace connector reports
process id and thread group id of both these involved processes. On
disconnection null process id is returned.
Such an event allows to create a simple automated userspace mechanism
to be aware about processes connecting to others, therefore predefined
process policies can be applied to them if needed.
Note, a detach signal is emitted only in case, if a tracer process
explicitly executes PTRACE_DETACH request. In other cases like tracee
or tracer exit detach event from proc connector is not reported.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
`make headers_check` complains that
linux-2.6/usr/include/linux/sdla.h:116: userspace cannot reference
function or variable defined in the kernel
this is due to that there is no such a kernel function,
void sdla(void *cfg_info, char *dev, struct frad_conf *conf, int quiet);
I don't know why we have it in a kernel header, so remove it.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new field 'force_sf_dma_mode' to plat_stmmacenet_data
struct to allow users to specify if they want to use force store forward
eventhough tx_coe is not available in hw.
without this flag stmmac driver will use cut-thru mode not use
store-forward mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goal of this patch is to permit nfnetlink providers not mandate
nfnl_mutex being held while nfnetlink_rcv_msg() calls them.
If struct nfnl_callback contains a non NULL call_rcu(), then
nfnetlink_rcv_msg() will use it instead of call() field, holding
rcu_read_lock instead of nfnl_mutex
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Florian Westphal <fw@strlen.de>
CC: Eric Leblond <eric@regit.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
In the future dst entries will be neigh-less. In that environment we
need to have an easy transition point for current users of
dst->neighbour outside of the packet output fast path.
Signed-off-by: David S. Miller <davem@davemloft.net>
It just makes it harder to see 1) what the code is doing
and 2) grep for all users of dst{->,.}neighbour
Signed-off-by: David S. Miller <davem@davemloft.net>
This will get us closer to being able to do "neigh stuff"
completely independent of the underlying dst_entry for
protocols (ipv4/ipv6) that wish to do so.
We will also be able to make dst entries neigh-less.
Signed-off-by: David S. Miller <davem@davemloft.net>
there is only one user of vlan_find_dev outside of the actual vlan code:
qlcnic uses it to iterate over some VLANs it knows.
let's just make vlan_find_dev private to the VLAN code and have the
iteration in qlcnic be a bit more direct. (a few rcu dereferences less
too)
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Amit Kumar Salecha <amit.salecha@qlogic.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
define ETH_P_8021AD to 88a8 (assigned by IEEE) and add ETH_P_QINQ{1,2,3}
for the pre-standard 9{1,2,3}00 types. all of them use 802.1q frame
format, with 1 bit used differently in some cases.
also define ETH_P_8021AH to 88e7 (assigned by IEEE). this is Mac-in-Mac
and uses a different, 16-byte header.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fake SIGSTOP during attach has numerous problems. PTRACE_SEIZE
is already fine, but we have basically the same problems is SIGSTOP
is sent on auto-attach, the tracer can't know if this signal signal
should be cancelled or not.
Change ptrace_event() to set JOBCTL_TRAP_STOP if the new child is
PT_SEIZED, this triggers the PTRACE_EVENT_STOP report.
Thereafter a PT_SEIZED task can never report the bogus SIGSTOP.
Test-case:
#define PTRACE_SEIZE 0x4206
#define PTRACE_SEIZE_DEVEL 0x80000000
#define PTRACE_EVENT_STOP 7
#define WEVENT(s) ((s & 0xFF0000) >> 16)
int main(void)
{
int child, grand_child, status;
long message;
child = fork();
if (!child) {
kill(getpid(), SIGSTOP);
fork();
assert(0);
return 0x23;
}
assert(ptrace(PTRACE_SEIZE, child, 0,PTRACE_SEIZE_DEVEL) == 0);
assert(wait(&status) == child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGSTOP);
assert(ptrace(PTRACE_SETOPTIONS, child, 0, PTRACE_O_TRACEFORK) == 0);
assert(ptrace(PTRACE_CONT, child, 0,0) == 0);
assert(waitpid(child, &status, 0) == child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGTRAP);
assert(WEVENT(status) == PTRACE_EVENT_FORK);
assert(ptrace(PTRACE_GETEVENTMSG, child, 0, &message) == 0);
grand_child = message;
assert(waitpid(grand_child, &status, 0) == grand_child);
assert(WIFSTOPPED(status) && WSTOPSIG(status) == SIGTRAP);
assert(WEVENT(status) == PTRACE_EVENT_STOP);
kill(child, SIGKILL);
kill(grand_child, SIGKILL);
return 0;
}
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
If the new child is traced, do_fork() adds the pending SIGSTOP.
It assumes that either it is traced because of auto-attach or the
tracer attached later, in both cases sigaddset/set_thread_flag is
correct even if SIGSTOP is already pending.
Now that we have PTRACE_SEIZE this is no longer right in the latter
case. If the tracer does PTRACE_SEIZE after copy_process() makes the
child visible the queued SIGSTOP is wrong.
We could check PT_SEIZED bit and change ptrace_attach() to set both
PT_PTRACED and PT_SEIZED bits simultaneously but see the next patch,
we need to know whether this child was auto-attached or not anyway.
So this patch simply moves this code to ptrace_init_task(), this
way we can never race with ptrace_attach().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
new_child->jobctl is not initialized during the fork, it is copied
from parent->jobctl. Currently this is harmless, the forking task
is running and copy_process() can't succeed if signal_pending() is
true, so only JOBCTL_STOP_DEQUEUED can be copied. Still this is a
bit fragile, it would be more clean to set ->jobctl = 0 explicitly.
Also, check ->ptrace != 0 instead of PT_PTRACED, move the
CONFIG_HAVE_HW_BREAKPOINT code up.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
It's just taking on one of two possible values, either
neigh_ops->output or dev_queue_xmit(). And this is purely depending
upon whether nud_state has NUD_CONNECTED set or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add overview documentation in Documentation/ABI/stable/firewire-cdev.
Improve the inline reference documentation in firewire-cdev.h:
- Add /* available since kernel... */ comments to event numbers
consistent with the comments on ioctl numbers.
- Shorten some documentation on an event and an ioctl that are
less interesting to current programming because there are newer
preferable variants.
- Spell Configuration ROM (name of an IEEE 1212 register) in
upper case.
- Move the dummy FW_CDEV_VERSION out of the reader's field of
vision. We should remove it from the header next year or so.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Between open(2) of a /dev/fw* and the first FW_CDEV_IOC_GET_INFO
ioctl(2) on it, the kernel already queues FW_CDEV_EVENT_BUS_RESET events
to be read(2) by the client. The get_info ioctl is practically always
issued right away after open, hence this condition only occurs if the
client opens during a bus reset, especially during a rapid series of bus
resets.
The problem with this condition is twofold:
- These bus reset events carry the (as yet undocumented) @closure
value of 0. But it is not the kernel's place to choose closures;
they are privat to the client. E.g., this 0 value forced from the
kernel makes it unsafe for clients to dereference it as a pointer to
a closure object without NULL pointer check.
- It is impossible for clients to determine the relative order of bus
reset events from get_info ioctl(2) versus those from read(2),
except in one way: By comparison of closure values. Again, such a
procedure imposes complexity on clients and reduces freedom in use
of the bus reset closure.
So, change the ABI to suppress queuing of bus reset events before the
first FW_CDEV_IOC_GET_INFO ioctl was issued by the client.
Note, this ABI change cannot be version-controlled. The kernel cannot
distinguish old from new clients before the first FW_CDEV_IOC_GET_INFO
ioctl.
We will try to back-merge this change into currently maintained stable/
longterm series, and we only document the new behaviour. The old
behavior is now considered a kernel bug, which it basically is.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
A system or a device may need to control suspend/wakeup events. It may
want to wakeup the system after a predefined amount of time or at a
predefined event decided while entering suspend for polling or delayed
work. Then, it may want to enter suspend again if its predefined wakeup
condition is the only wakeup reason and there is no outstanding events;
thus, it does not wakeup the userspace unnecessary or unnecessary
devices and keeps suspended as long as possible (saving the power).
Enabling a system to wakeup after a specified time can be easily
achieved by using RTC. However, to enter suspend again immediately
without invoking userland and unrelated devices, we need additional
features in the suspend framework.
Such need comes from:
1. Monitoring a critical device status without interrupts that can
wakeup the system. (in-suspend polling)
An example is ambient temperature monitoring that needs to shut down
the system or a specific device function if it is too hot or cold. The
temperature of a specific device may be needed to be monitored as well;
e.g., a charger monitors battery temperature in order to stop charging
if overheated.
2. Execute critical "delayed work" at suspend.
A driver or a system/board may have a delayed work (or any similar
things) that it wants to execute at the requested time.
For example, some chargers want to check the battery voltage some
time (e.g., 30 seconds) after the battery is fully charged and the
charger has stopped. Then, the charger restarts charging if the voltage
has dropped more than a threshold, which is smaller than "restart-charger"
voltage, which is a threshold to restart charging regardless of the
time passed.
This patch allows to add "suspend_again" callback at struct
platform_suspend_ops and let the "suspend_again" callback return true if
the system is required to enter suspend again after the current instance
of wakeup. Device-wise suspend_again implemented at dev_pm_ops or
syscore is not done because: a) suspend_again feature is usually under
platform-wise decision and controls the behavior of the whole platform
and b) There are very limited devices related to the usage cases of
suspend_again; chargers and temperature sensors are mentioned so far.
With suspend_again callback registered at struct platform_suspend_ops
suspend_ops in kernel/power/suspend.c with suspend_set_ops by the
platform, the suspend framework tries to enter suspend again by
looping suspend_enter() if suspend_again has returned true and there has
been no errors in the suspending sequence or pending wakeups (by
pm_wakeup_pending).
Tested at Exynos4-NURI.
[rjw: Fixed up kerneldoc comment for suspend_enter().]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
cpufreq table allocated by opp_init_cpufreq_table is better
freed by OPP layer itself. This allows future modifications to
the table handling to be transparent to the users.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove it, as it indirectly exposes netdev features. It's not used in
iproute2 (2.6.38) - is anything else using its interface?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not used anywhere except net/core/dev.c now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.
The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock". Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.
To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock. Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.
This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Reviewed-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a new function pm_genpd_poweroff_unused() queuing up the
execution of pm_genpd_poweroff() for every initialized generic PM
domain. Calling it will cause every generic PM domain without
devices in use to be powered off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
This never, ever, happens.
Neighbour entries are always tied to one address family, and therefore
one set of dst_ops, and therefore one dst_ops->protocol "hh_type"
value.
This capability was blindly imported by Alexey Kuznetsov when he wrote
the neighbour layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.
Rename from arp_bind_neighbour to rt_bind_neighbour.
Use new helpers {__,}ipv4_neigh_lookup()
In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
Almost all of these have long outstayed their welcome.
And for every one of these macros, there are 10 features for which we
didn't add macros.
Let's just delete them all, and get out of habit of doing things this
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This boolean function simply returns whether or not the runtime status
of the device is 'suspended'. Unlike pm_runtime_suspended(), this
function returns the runtime status whether or not runtime PM for the
device has been disabled or not.
Also add entry to Documentation/power/runtime.txt
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
RX rings should use GFP_KERNEL allocations if possible, add
__netdev_alloc_skb_ip_align() helper to ease this.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
A deadlock may occur if one of the PM domains' .start_device() or
.stop_device() callbacks or a device driver's .runtime_suspend() or
.runtime_resume() callback executed by the core generic PM domain
code uses a "wrong" runtime PM helper function. This happens, for
example, if .runtime_resume() from one device's driver calls
pm_runtime_resume() for another device in the same PM domain.
A similar situation may take place if a device's parent is in the
same PM domain, in which case the runtime PM framework may execute
pm_genpd_runtime_resume() automatically for the parent (if it is
suspended at the moment). This, of course, is undesirable, so
the generic PM domains code should be modified to prevent it from
happening.
The runtime PM framework guarantees that pm_genpd_runtime_suspend()
and pm_genpd_runtime_resume() won't be executed in parallel for
the same device, so the generic PM domains code need not worry
about those cases. Still, it needs to prevent the other possible
race conditions between pm_genpd_runtime_suspend(),
pm_genpd_runtime_resume(), pm_genpd_poweron() and pm_genpd_poweroff()
from happening and it needs to avoid deadlocks at the same time.
To this end, modify the generic PM domains code to relax
synchronization rules so that:
* pm_genpd_poweron() doesn't wait for the PM domain status to
change from GPD_STATE_BUSY. If it finds that the status is
not GPD_STATE_POWER_OFF, it returns without powering the domain on
(it may modify the status depending on the circumstances).
* pm_genpd_poweroff() returns as soon as it finds that the PM
domain's status changed from GPD_STATE_BUSY after it's released
the PM domain's lock.
* pm_genpd_runtime_suspend() doesn't wait for the PM domain status
to change from GPD_STATE_BUSY after executing the domain's
.stop_device() callback and executes pm_genpd_poweroff() only
if pm_genpd_runtime_resume() is not executed in parallel.
* pm_genpd_runtime_resume() doesn't wait for the PM domain status
to change from GPD_STATE_BUSY after executing pm_genpd_poweron()
and sets the domain's status to GPD_STATE_BUSY and increments its
counter of resuming devices (introduced by this change) immediately
after acquiring the lock. The counter of resuming devices is then
decremented after executing __pm_genpd_runtime_resume() for the
device and the domain's status is reset to GPD_STATE_ACTIVE (unless
there are more resuming devices in the domain, in which case the
status remains GPD_STATE_BUSY).
This way, for example, if a device driver's .runtime_resume()
callback executes pm_runtime_resume() for another device in the same
PM domain, pm_genpd_poweron() called by pm_genpd_runtime_resume()
invoked by the runtime PM framework will not block and it will see
that there's nothing to do for it. Next, the PM domain's lock will
be acquired without waiting for its status to change from
GPD_STATE_BUSY and the device driver's .runtime_resume() callback
will be executed. In turn, if pm_runtime_suspend() is executed by
one device driver's .runtime_resume() callback for another device in
the same PM domain, pm_genpd_poweroff() executed by
pm_genpd_runtime_suspend() invoked by the runtime PM framework as a
result will notice that one of the devices in the domain is being
resumed, so it will return immediately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, the .start_device() and .stop_device() callbacks from
struct generic_pm_domain() as well as the device drivers' runtime PM
callbacks used by the generic PM domains code are executed under
the generic PM domain lock. This, unfortunately, is prone to
deadlocks, for example if a device and its parent are boths members
of the same PM domain. For this reason, it would be better if the
PM domains code didn't execute device callbacks under the lock.
Rework the locking in the generic PM domains code so that the lock
is dropped for the execution of device callbacks. To this end,
introduce PM domains states reflecting the current status of a PM
domain and such that the PM domain lock cannot be acquired if the
status is GPD_STATE_BUSY. Make threads attempting to acquire a PM
domain's lock wait until the status changes to either
GPD_STATE_ACTIVE or GPD_STATE_POWER_OFF.
This change by itself doesn't fix the deadlock problem mentioned
above, but the mechanism introduced by it will be used for for this
purpose by a subsequent patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Looks like I forgot to document the "gfp" parameter
to cfg80211_gtk_rekey_notify, add it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 maintains a running average of the RSSI when a STA
is associated to an AP. Report threshold events to any driver
that has registered callbacks for getting RSSI measurements.
Implement callbacks in mac80211 so that driver can set thresholds.
Add callbacks in mac80211 which is invoked when an RSSI threshold
event occurs.
mac80211: add tracing to rssi_reports api and remove extraneous fn argument
mac80211: scale up rssi thresholds from driver by 16 before storing
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
And mask the hash function result by simply shifting
down the "->hash_shift" most significant bits.
Currently which bits we use is arbitrary since jhash
produces entropy evenly across the whole hash function
result.
But soon we'll be using universal hashing functions,
and in those cases more entropy exists in the higher
bits than the lower bits, because they use multiplies.
Signed-off-by: David S. Miller <davem@davemloft.net>
There can 3 reasons for the "command reject" reply produced
by the stack. Each such reply should be accompanied by the
relevand data ( as defined in spec. ). Currently there is one
instance of "command reject" reply with reason "invalid cid"
wich is fixed. Also, added clean-up definitions related to the
"command reject" replies.
Signed-off-by: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Rearrange struct sk_buff members comments to follow their
definition order. Also, add missing comments for ooo_okay
and dropcount members.
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>