maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we start building glue layers as modules,
we need to be careful with the fifo_mode changes
otherwise that weird ifdeferry won't evaluate
correctly. Add the missing _MODULE variants for
all glue layers to prevent everybody from using
fifo_mode 2.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.
This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if we have more endpoints configured than
enabled on fifo_mode, then we need to be
careful on save/restore context operations,
otherwise we will try to access uninitialized
__iomem pointer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function has no user in my tree. It looks like it belongs to
net2280 but it somehow morphed into the dummy_hcd. So I remove it
before it spreads into more drivers.
After some digging I figured out that the only user was removed in
|commit 9079e91b5b
|Author: David Brownell <david-b@pacbell.net>
|Date: Wed May 7 16:00:36 2008 -0700
|
| USB: serial gadget: cleanup/reorg
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taking the correct struct once avoids doing the speed dance.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gadget_to_dummy_hcd() already does the speed check, so
it's unnecessary to unroll that all the time.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit 53832daea ("usb: gadget: dummy_hcd: use the shared_hcd
infrastructure") the is_otg field was set in dummy_udc_probe(). It seems
to me that this field is used in gadget's bind function. Therefore I'm
moving it before the bind() callback is called.
Cc: Tatyana Brokhman <tlinder@codeaurora.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removed code does the same thing as dummy_pullup(). The only
difference is that in dummy_udc_stop() the first dummy_pullup()
did not call usb_hcd_poll_rh_status().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the gadget controller number is only used
during bind() to update descriptors and/or
check that a particular controller can support
a particular gadget driver.
Because of that, we can remove the ifdef
trickery as it's a rather small optimization
anyway.
While at that, also sort the entries
alphabetically and add a comment stating we
want to keep the list ordered alphabetically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 72c973d (usb: gadget: add usb_endpoint_descriptor
to struct usb_ep) has introduced a compile error to
ci13xxx_udc. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes the error path: If the second device fails to register
we never remove the first one.
This is compile-tested only. I don't see any difference between those
two. Maybe we should just use one name instead?
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it udev won't be able to load the driver once it notices the
device unbound.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case pci_register_driver() fails it error will be 0 in case
platform_driver_register() was fine. Also without PCI
pci_register_driver() evaluates to 1 which is well, special. If
platform_driver_register() returns EINVAL or EBUSY we end up with 0.
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new module parameter to dummy_hcd
called is_high_speed.
When set to false the connected device will be forced
to operate in full-speed mode. By default, this parameter
is set to 'true'.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.
USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.
A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
[ balbi@ti.com : slight change to commit log
fixed one coding style issue ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a preparation for adding SuperSpeed
support to dummy hcd.
It takes the master side fields out of the struct
dummy to a separate structure. The init process
was also modified to resemble the way it is
done by xHCI.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used by the Gadget drivers to specify
the maximum speed they support, meaning: the maximum
speed they can provide descriptors for.
The driver speed will be set in consideration of this
value.
[ balbi@ti.com : dropped the ifdeffery ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "channel_program" member was renamed to "adjust_channel_params",
but the documentation wasn't updated.
Reported-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch defines necessary fields to support
streaming for USB3.0.
It implements a new function, called
usb_ep_autoconfig_ss(), to be used instead of the
existing usb_ep_autoconfig() when working in
SuperSpeed mode and there is a need to search for
an endpoint according to the number of required
streams.
[ balbi@ti.com : slight changes to commit log ]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the coding style of a few switches on the
gadget framework.
[ balbi@ti.com : add a commit log ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add config_ep_by_speed() to configure the endpoint
according to the gadget speed.
Using this function will spare the FDs from handling
the endpoint chosen descriptor.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change usb_ep_enable() prototype to use endpoint
descriptor from usb_ep.
This optimization spares the FDs from saving the
endpoint chosen descriptor. This optimization is
not full though. To fully exploit this change, one
needs to update all the UDCs as well since in the
current implementation each of them saves the
endpoint descriptor in it's internal (and extended)
endpoint structure.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
peripheral drivers are using usb_add_gadget()/usb_del_gadget() to
register/unregister to the udc-core.
The udc-core will take the first available gadget driver and attach
function driver which is calling usb_gadget_register_driver(). This is
the same behaviour we have right now.
Only dummy_hcd was tested, the others were compiled tested.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Roy Huang <roy.huang@analog.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: cxie4 <cxie4@marvell.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this class will be used to abstract away several of the duplicated
operations scattered among the USB gadget controller drivers.
Later, we can add an atomic notifier to tell interested drivers about
what's happening with the controller. Notifications such as suspend,
resume, enumerated, etc. will be useful, at a minimum, for implementing
usb charger detection.
As part of the converting process usb_gadget_probe_driver() is no longer
part of each udc but pushed into the ->stap() callback. The same for his
couterpart.
The core is currently set explicit to 'n'. It will be changed to 'y' once
all users are converted since it provides functions which clash with
other drivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1471) deprecates the File-backed Storage Driver and
schedules its replacement for the 3.8 kernel release (about two years
from now). Users are advised to switch to the Mass Storage Gadget
instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes the connection fail happen on renesas_usbhs.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return error on out of range cpsdvsr value.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio/basic_mmio: add missing include of spinlock_types.h
gpio/nomadik: fix sleepmode for elder Nomadik
We leak the memory allocated to 'phi' when the variable goes out of scope
in hfcsusb_ph_info().
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King said:
>
> So, to summarize what its doing:
>
> 1. It allocates buffers for rx and tx.
> 2. It maps them with dma_map_single().
> This transfers ownership of the buffer to the DMA device.
> 3. In ep93xx_xmit,
> 3a. It copies the data into the buffer with skb_copy_and_csum_dev()
> This violates the DMA buffer ownership rules - the CPU should
> not be writing to this buffer while it is (in principle) owned
> by the DMA device.
> 3b. It then calls dma_sync_single_for_cpu() for the buffer.
> This transfers ownership of the buffer to the CPU, which surely
> is the wrong direction.
> 4. In ep93xx_rx,
> 4a. It calls dma_sync_single_for_cpu() for the buffer.
> This at least transfers the DMA buffer ownership to the CPU
> before the CPU reads the buffer
> 4b. It then uses skb_copy_to_linear_data() to copy the data out.
> At no point does it transfer ownership back to the DMA device.
> 5. When the driver is removed, it dma_unmap_single()'s the buffer.
> This transfers ownership of the buffer to the CPU.
> 6. It frees the buffer.
>
> While it may work on ep93xx, it's not respecting the DMA API rules,
> and with DMA debugging enabled it will probably encounter quite a few
> warnings.
This patch fixes these violations.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a197b59ae6 (mm: fail GFP_DMA allocations when ZONE_DMA is not
configured) made page allocator to return NULL if GFP_DMA is set but
CONFIG_ZONE_DMA is disabled.
This causes ep93xx_eth to fail:
WARNING: at mm/page_alloc.c:2251 __alloc_pages_nodemask+0x11c/0x638()
Modules linked in:
[<c0035498>] (unwind_backtrace+0x0/0xf4) from [<c0043da4>] (warn_slowpath_common+0x48/0x60)
[<c0043da4>] (warn_slowpath_common+0x48/0x60) from [<c0043dd8>] (warn_slowpath_null+0x1c/0x24)
[<c0043dd8>] (warn_slowpath_null+0x1c/0x24) from [<c0083b6c>] (__alloc_pages_nodemask+0x11c/0x638)
[<c0083b6c>] (__alloc_pages_nodemask+0x11c/0x638) from [<c00366fc>] (__dma_alloc+0x8c/0x3ec)
[<c00366fc>] (__dma_alloc+0x8c/0x3ec) from [<c0036adc>] (dma_alloc_coherent+0x54/0x60)
[<c0036adc>] (dma_alloc_coherent+0x54/0x60) from [<c0227808>] (ep93xx_open+0x20/0x864)
[<c0227808>] (ep93xx_open+0x20/0x864) from [<c0283144>] (__dev_open+0xb8/0x108)
[<c0283144>] (__dev_open+0xb8/0x108) from [<c0280528>] (__dev_change_flags+0x70/0x128)
[<c0280528>] (__dev_change_flags+0x70/0x128) from [<c0283054>] (dev_change_flags+0x10/0x48)
[<c0283054>] (dev_change_flags+0x10/0x48) from [<c001a720>] (ip_auto_config+0x190/0xf68)
[<c001a720>] (ip_auto_config+0x190/0xf68) from [<c00233b0>] (do_one_initcall+0x34/0x18c)
[<c00233b0>] (do_one_initcall+0x34/0x18c) from [<c0008400>] (kernel_init+0x94/0x134)
[<c0008400>] (kernel_init+0x94/0x134) from [<c0030858>] (kernel_thread_exit+0x0/0x8)
Since there is no restrictions for DMA on ep93xx, we can fix this by just
removing the GFP_DMA flag from the call.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use simply kmalloc() to allocate the buffers. This also simplifies the
code and allows us to perform DMA sync operations more easily.
Memory is allocated with only GFP_KERNEL since there are no DMA allocation
restrictions on this platform.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't use NULL for any DMA API functions, unless we are dealing with
ISA or EISA device. So pass correct struct dev pointer to these functions.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
/tmp/ccvoZ6h8.s: Assembler messages:
/tmp/ccvoZ6h8.s:284: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:881: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:1087: Warning: register range not in ascending order
by ensuring that we have temporary variables placed into specific
registers. Reorder the code a bit to allow the resulting assembly
to be slightly more optimal.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were clearing out the multicast filter whenever the interface was
upped, and not setting the mode bits correctly. This can cause
problems if there are any multicast addresses already set at this
point, or if ALLMULTI was set.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the compiler can (and does) optimize register reads away
from within loops, and other such optimizations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the legit warnings 'make W=3 drivers/ide/ide-cd.c'
generates is:
drivers/ide/ide-cd.c: In function ide_cd_do_request
drivers/ide/ide-cd.c:828:2: warning: conversion to int from \
unsigned int may change the sign of the result
drivers/ide/ide-cd.c:833:2: warning: conversion to int from \
unsigned int may change the sign of the result
nsectors is declared int, should be unsigned int.
blk_rq_sectors() returns unsigned int, and ide_complete_rq
expects unsigned int as well. Fixes both warnings.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Andrzej Siewior
Felipe Balbi
Tatyana Brokhman
Mike Frysinger
Alan Stern
Kuninori Morimoto
Greg Kroah-Hartman
Linus Torvalds
Virupax Sadashivpetimath
Jesper Juhl
Mika Westerberg
Daniel Hellstrom
Russell King - ARM Linux
Connor Hansen