Pull MIPS fixes from Ralf Baechle:
"Random small fixes across the MIPS code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: CMP: Fix physical core number calculation logic
MIPS: JZ4740: Forward declare struct uart_port in header.
MIPS: JZ4740: Fix '#include guard' in serial.h
MIPS: hugetlbfs: Fix hazard between tlb write and pagemask restoration.
MIPS: Restore pagemask after dumping the TLB.
MIPS: Hugetlbfs: Handle huge pages correctly in pmd_bad()
MIPS: R5000: Fix TLB hazard handling.
MIPS: tlbex: Deal with re-definition of label
MIPS: Make __{,n,u}delay declarations match definitions and generic delay.h
The CPUNum Field in EBase register is 10bit wide, so after 1 bit right
shift, the mask value should be 0x1ff.
Signed-off-by: jerin jacob <jerinjacobk@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Place comments in:
arch/mips/include/asm/Kbuild
arch/tile/include/arch/Kbuild
to make them non-empty so that the patch program doesn't remove them when it
reduces them to nothing.
Possibly they should be just deleted, but it's possible that they'll acquire
generic-y or genhdr-y lines in future, so I'm keeping them around for the
moment.
Note that MIPS will compile happily if the file is deleted instead. I haven't
tested TILE, but I suspect it will be the same there.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Ralf Baechle <ralf@linux-mips.org>
cc: Chris Metcalf <cmetcalf@tilera.com>
On some CPU the write to pagemask might complete before the TLB write
instruction reads from the pagemask register.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R5000 and the Nevada CPUs (RM5230, RM5231, RM5260, RM5261, RM5270 and
RM5271) are basically the same CPU core and all are documented to require
two instructions separating a write to c0_pagemask, c0_entryhi, c0_entrylo0,
c0_entrylo1 or c0_index.
So far we were only providing on cycle before / after a TLBR/TLBWI
for R5000 but 3 cycles before and 1 cycles after for the Nevadas.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The microassembler used in tlbex.c does not notice if a label is redefined
resulting in relocations against such labels silently missrelocated.
The issues exists since commit add6eb04776db4189ea89f596cbcde31b899be9d
[Synthesize TLB exception handlers at runtime.] in 2.6.10 and went unnoticed
for so long because the relocations for the affected branches got computed
to do something *almost* sensible.
The issue affects R4000, R4400, QED/IDT RM5230, RM5231, RM5260, RM5261,
RM5270 and RM5271 processors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
At some recent point arch/mips/include/asm/delay.h has started being
included into csrc-octeon.c where the __?delay() functions are defined.
This causes a compile failure due to conflicting declarations and
definitions of the functions.
It turns out that the generic definitions in arch/mips/lib/delay.c also
conflict.
Proposed fix: Declare the functions to take unsigned long parameters
just like asm-generic (and x86) does. Update __delay to agree
(__ndelay and __udelay need no change).
Bonus: Get rid of 'inline' from __delay() definition, as it is globally
visible, and the compiler should be making this decision itself (it does
in fact inline the function without being told to).
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.
For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.
This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.
Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This fault was detected using the kgdb test suite on boot and it
crashes recursively due to the fact that CONFIG_KPROBES on mips adds
an extra die notifier in the page fault handler. The crash signature
looks like this:
kgdbts:RUN bad memory access test
KGDB: re-enter exception: ALL breakpoints killed
Call Trace:
[<807b7548>] dump_stack+0x20/0x54
[<807b7548>] dump_stack+0x20/0x54
The fix for now is to have kgdb return immediately if the fault type
is DIE_PAGE_FAULT and allow the kprobe code to decide what is supposed
to happen.
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
The new SCCNXP driver supports the SC2681 chips used in RM400 machines.
We now use the new driver instead of the old SC26xx driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4417/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
LD arch/mips/pci/built-in.o
WARNING: arch/mips/pci/built-in.o(.devinit.text+0x2a0): Section mismatch in reference from the function malta_piix_func0_fixup() to the variable .init.data:pci_irq
The function __devinit malta_piix_func0_fixup() references
a variable __initdata pci_irq.
If pci_irq is only used by malta_piix_func0_fixup then
annotate pci_irq with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Originally added in 05b541489c48e7fbeec19a92acf8683230750d0a [Merge with
Linux 2.5.5.] over 10 years ago but never been used.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1100/1500 are similar to their DB-cousins but with a few
more devices on the bus.
This patch adds PB1100/1500 support to the existing DB1100/1500
code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: lnux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1550 is more or less a DB1550 without the PCI IDE controller,
a more complicated (read: configurable) Flash setup and some other
minor changes. Like the DB1550 it can be automatically detected by
reading the CPLD ID register bits.
This patch adds PB1550 detection and setup to the DB1550 code.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We don't have to do a separate shift to eliminate the software bits,
just rotate them into the fill and they will be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4294/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most supported systems currently hardwire cpu_has_dsp to 0, so we also
can disable support for cpu_has_dsp2 resulting in a slightly smaller
kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[ralf@linux-mips.org: This patch really only detects the ASE and passes its
existence on to userland via /proc/cpuinfo. The DSP ASE Rev 2. adds new
resources but no resources that would need management by the kernel.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a dual issue processor GCC generates code that saves a couple of
clock cycles per loop if we rearrange things slightly. Checking for
p != end saves a SLTU per loop, moving the increment to the middle can
let it dual issue on multi-issue processors.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add hardware performance counter support to kernel "perf" code for
BMIPS5000. The BMIPS5000 performance counters are similar to MIPS
MTI cores, so the changes were mostly made in perf_event_mipsxx.c
which is typically for MTI cores.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the Kconfig option CONFIG_MIPS_MT_SMP into CONFIG_MIPS_MT_SMP
and CONFIG_MIPS_PERF_SHARED_TC_COUNTERS so some of the code used
for performance counters that are shared between threads can be used
for MIPS cores that are not MT_SMP.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4108/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The #ifdef for CONFIG_HW_PERF_EVENTS is not needed because the
Makefile will only compile the module if this config option is set.
This means that the code under #else would never be compiled. This
may have been done to leave the original broken code around for
reference, but the FIXME comment above the code already shows the
broken code.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4107/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI (Program Counter Interrupt) bit in the "cause" register
is mandatory for MIPS32R2 cores, but has also been added to some R1
cores (BMIPS5000). This change adds a cpu feature bit to make it
easier to check for and use this feature.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the indicator from 0xffffffff in the "event_id" member to
zero in the "cntr_mask" member. This removes the need to initialize
entries that are unsupported. This also solves a problem where the
number of entries in the table was increased based on a globel enum
used for all platforms, but the new unsupported entries were not added
for mips. This was leaving new table entries of all zeros that we not
marked UNSUPPORTED.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can save an instruction in the TLB Refill path for kernel mappings
by aligning swapper_pg_dir on a 64K boundary. The address of
swapper_pg_dir can be generated with a single LUI instead of
LUI/{D}ADDUI.
The alignment of __init_end is bumped up to 64K so there are no holes
between it and swapper_pg_dir, which is placed at the very beginning
of .bss.
The alignment of invalid_pmd_table and invalid_pte_table can be
relaxed to PAGE_SIZE. We do this by using __page_aligned_bss, which
has the added benefit of eliminating alignment holes in .bss.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-arch@vger.kernel.org,
Cc: linux-kernel@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Patchwork: https://patchwork.linux-mips.org/patch/4220/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've maintained this patch, originally from Thiemo Seufer in 2004, for a
really long time, but I think it's time for it to get a look at for
possible inclusion. I have had no problems with it across various SGI
systems over the years.
To quote the post here:
http://www.linux-mips.org/archives/linux-mips/2004-12/msg00000.html
"the atomic functions use so far memory references for the inline
assembler to access the semaphore. This can lead to additional
instructions in the ll/sc loop, because newer compilers don't
expand the memory reference any more but leave it to the assembler.
The appended patch uses registers instead, and makes the ll/sc
arguments more explicit. In some cases it will lead also to better
register scheduling because the register isn't bound to an output
any more."
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQcV6pAAoJEN0jrNd/PrOh594P/3NHPjnTiyAZpUICX4mJeoMd
1rX685HofCyX5jlHloS1pLRXYtIPZP97We5crNR/k/RujKcHAqAFzLtG2Jj93gxm
nRUwLZ4xbrAgeaZeJV8YG1naWx9R1OjrK2sv+FyHRWsn9UZus2vDMV7tB0oNWo9k
DMhtF1q7gQxx4nRu8z9FFybyItQinVREODNs+Gdv6AOJ36t+mOsGPL3LKZeFsIG3
LdaB1p3t/07Job4KwGYYRjkOR7bIQ+ADnnO8Pkk0a9lxkMI8rA0uFbLwgyx7Hohh
xZtm8R5il2IlHwqh52RzpShceWICxCZ3htuIXTRbVa1PSEsBzZ66W2CT7sy1jPm5
lJlHgc7abaiwijtoG76I+Lgslv5UTViBuIYHSX4dH2kF3Jgm2SgTBNzZYePI5MMT
BI3xc9WnwBpxgMybJsPHfU0Ff6O/9h9ab7q5lBOHkQJittahYxzWD+FgYlalcAa+
I919iFREKNZytewLnXu+4TG0RfacQoj6D5G+SquOGmXyKYRhhJ1O6WodnRZHi/0n
M6J0f6fLxpomI1RMn44VYP43OPJCDYxgXYoDLwCZQL9tSWYpdhXoDrjcIPO547w1
ZS5HTXUE4DrxeYjoeqL555vtQIooM9CuH4JwKlz5zzea8NPC8eVtmNFTTWE6wKWX
ZIOOLVvw/FI0/DSjBb8H
=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Merge patches from Andrew Morton:
"A few misc things and very nearly all of the MM tree. A tremendous
amount of stuff (again), including a significant rbtree library
rework."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (160 commits)
sparc64: Support transparent huge pages.
mm: thp: Use more portable PMD clearing sequenece in zap_huge_pmd().
mm: Add and use update_mmu_cache_pmd() in transparent huge page code.
sparc64: Document PGD and PMD layout.
sparc64: Eliminate PTE table memory wastage.
sparc64: Halve the size of PTE tables
sparc64: Only support 4MB huge pages and 8KB base pages.
memory-hotplug: suppress "Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning
mm: memcg: clean up mm_match_cgroup() signature
mm: document PageHuge somewhat
mm: use %pK for /proc/vmallocinfo
mm, thp: fix mlock statistics
mm, thp: fix mapped pages avoiding unevictable list on mlock
memory-hotplug: update memory block's state and notify userspace
memory-hotplug: preparation to notify memory block's state at memory hot remove
mm: avoid section mismatch warning for memblock_type_name
make GFP_NOTRACK definition unconditional
cma: decrease cc.nr_migratepages after reclaiming pagelist
CMA: migrate mlocked pages
kpageflags: fix wrong KPF_THP on non-huge compound pages
...
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core page allocator ensures that page flags are zeroed when freeing
pages via free_pages_check. A number of architectures (ARM, PPC, MIPS)
rely on this property to treat new pages as dirty with respect to the data
cache and perform the appropriate flushing before mapping the pages into
userspace.
This can lead to cache synchronisation problems when using hugepages,
since the allocator keeps its own pool of pages above the usual page
allocator and does not reset the page flags when freeing a page into the
pool.
This patch adds a new architecture hook, arch_clear_hugepage_flags, so
that architectures which rely on the page flags being in a particular
state for fresh allocations can adjust the flags accordingly when a page
is freed into the pool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_DEBUG_KMEMLEAK config option and select it in corresponding
architecture Kconfig files. DEBUG_KMEMLEAK now only depends on
HAVE_DEBUG_KMEMLEAK.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
Pull kbuild fixes from Michal Marek:
"Here are two fixes I intended to send after v3.6-rc7, but failed to do
so. So please pull them for v3.7-rc1 and they will be picked up by
stable.
The first one fixes gcc -x <language> syntax in various build-time
tests, which icecream and possible other gcc wrappers did not
understand (and yes, icecream is going to be fixed as well).
The second one fixes make tar-pkg so that unpacking the tarball does
not replace the /lib -> /usr/lib symlink on recent Fedora releases."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix gcc -x syntax
kbuild: Do not package /boot and /lib in make tar-pkg
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This is a prerequisite for allowing the PWM driver to be converted to
the PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This is a preparatory patch for the introduction of NT_SIGINFO elf note.
Make the location of compat_siginfo_t uniform across eight architectures
which have it. Now it can be pulled in by including asm/compat.h or
linux/compat.h.
Most of the copies are verbatim. compat_uid[32]_t had to be replaced by
__compat_uid[32]_t. compat_uptr_t had to be moved up before
compat_siginfo_t in asm/compat.h on a several architectures (tile already
had it moved up). compat_sigval_t had to be relocated from linux/compat.h
to asm/compat.h.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
jerin jacob
Ralf Baechle
Antony Pavlov
David Howells
David Daney
Jeff Layton
Jason Wessel
Thomas Bogendoerfer
Manuel Lauss
David Daney
Steven J. Hill
Al Cooper
Joshua Kinard
David Woodhouse
Shaohua Li
Will Deacon
Catalin Marinas
Thierry Reding
Denys Vlasenko