Return an error from wm_hubs_read_dc_servo() if hubs->dcs_readback_mode is not
correctly initialized. You might as well bail out since nothing is likely to
work correctly afterwards.
sound/soc/codecs/wm_hubs.c:321:11: warning: 'reg_r' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm_hubs.c:251:13: note: 'reg_r' was declared here
sound/soc/codecs/wm_hubs.c:322:11: warning: 'reg_l' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm_hubs.c:251:6: note: 'reg_l' was declared here
gcc version 4.6.3
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some circumstances we may need to flush volume updates to the device
after switching to class W mode. Do this unconditionally to ensure that
these situations are handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's currently only used in one place but another user will be added
shortly and there's an argument it's clearer anyway.
Also add support for readback in mode 1, though it's not currently used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than invalidating the cached DCS value every time the headphone
gain changes store multiple values, indexed by gain. This allows the
optimisation we get from the cache to take effect more often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Class W can be used for any path where only data from the DAC is routed
to the headphones. Currently we only enable it when the direct DAC to
headphone path is used but it can also be enabled for paths that go via
the output mixer providing the DAC is the only input to the output mixer.
Implement support for this, including updates to the class W status when
the output mixer configuration is changed. This also allows us to enable
the DC servo optimisations for DAC to headphone paths where the output
mixer is used.
In general the direct DAC path is still preferred as this will offer
better performance on most wm_hubs devices but these additional paths
can simplify use case management.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the analogue portions of the checks for class W are the same over
all the devices factor out these checks into wm_hubs and while we're at
it also use wm_hubs_dac_hp_direct() to enable class W optimisations on
more paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimisations which we can do with caching the headphone DCS result in
wm_hubs have only been enabled in cases where class W is enabled. However,
there are more use cases which can benefit from the cache, especially with
WM8994 series devices with their more advanced digital routing.
Rather than keying off the class W information from the CODECs have a
check in wm_hubs for a suitable path and use that to determine if we can
deploy our headphone optimisations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While we need to clean up unused single ended line outputs we don't want
to do this if the outputs are in differential mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IN1L/R is routed to both line output mixers, we don't route IN1 to LINEOUT1
and IN2 to LINEOUT2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The thermal shutdown support in wm_hubs devices is tied to the speaker
drivers (which are the only high power subsystems within the device).
Ensure minimal current usage when the thermal shutdown support is not
required by disabling the circuit when the speaker drivers are powered
down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_soc_*_volsw_2r functionality has been merged to
*volsw callbacks.
Few places still used the get, or put variant of volsw_2r,
replace those with the corresponding *_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the macros for controls require custom get/put function.
This is to make sure that the soc_mixer_control is used
consistently among the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently this does not actually do anything, it is being introduced in
order to facilitate additional power optimisations for current generation
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some devices can have performance optimized by setting different offsets
for left and right channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Later WM8994 devices implement a new DC servo readback mode with the
register used to access the offset moved to register 0x59. Implement
support for this and enable it on the appropriate devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This does not function correctly in all circumstances so disable the
periodic updates unconditionally for stable; a future patch will reenable
where appropriate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It was consistently wrong for everything except WM8993 so should be no
functional change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.comm>
Some devices do not support manual updates of the DC servo.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Also fix a left/right typo while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com.
Cc: stable@kernel.org
Tim Gardner
Mark Brown
Liam Girdwood
UK KIM
Clemens Ladisch
Peter Ujfalusi