Create a driver with the generic watchdog interface
for the MEI iAMT watchdog device.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the watchdog core found on newer MediaTek Wifi
SoCs MT7621 and MT7628. There is no symbol for MT7628 as it is a subtype of
MT7620 so we depend on that instead.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds support for the Sigma Designs SMP86xx/SMP87xx family built-in
watchdog.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Zodiac Aerospace RAVE Watchdog Procesor.
This device implements a watchdog timer, accessible over I2C.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add WD support for Alphascale asm9260 SoC. This driver
provide support for different function modes:
- HW mode to trigger SoC reset on timeout
- SW mode do soft reset if needed
- DEBUG mode
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog is instantiated in a FPGA that is memory mapped. It is
made of only one register, called the feed register. Writing to this
register will re-arm the watchdog for a given time (and enable it if it
was disable). It can be disabled by writing a special value into it.
It is part of a syscon block, and the watchdog register offset in this
block varies from board to board. This offset is passed in the syscon
property after the phandle to the syscon node.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds watchdog driver for CSRatlas7 platform.
On CSRatlas7, the 6th timer can act as a watchdog timer
when the Watchdog mode is enabled.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: William Wang <William.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds following attributes to watchdog device's sysfs interface
to read its different status.
* state - reads whether device is active or not
* identity - reads Watchdog device's identity string.
* timeout - reads current timeout.
* timeleft - reads timeleft before watchdog generates a reset
* bootstatus - reads status of the watchdog device at boot
* status - reads watchdog device's internal status bits
* nowayout - reads whether nowayout feature was set or not
Testing with iTCO_wdt:
# cd /sys/class/watchdog/watchdog1/
# ls
bootstatus dev device identity nowayout power state
subsystem timeleft timeout uevent
# cat identity
iTCO_wdt
# cat timeout
30
# cat state
inactive
# echo > /dev/watchdog1
# cat timeleft
26
# cat state
active
# cat bootstatus
0
# cat nowayout
0
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If I2C is built as module, the iTCO watchdog driver must be built as module
as well. I2C_I801 must only be selected if I2C is configured.
This fixes the following build errors, seen if I2C=m and ITCO_WDT=y.
i2c-i801.c:(.text+0x2bf055): undefined reference to `i2c_del_adapter'
i2c-i801.c:(.text+0x2c13e0): undefined reference to `i2c_add_adapter'
i2c-i801.c:(.text+0x2c17bd): undefined reference to `i2c_new_device'
Fixes: 2a7a0e9bf7 ("watchdog: iTCO_wdt: Add support for TCO on Intel Sunrisepoint")
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
From SAMA5D4, the watchdog timer is upgrated with a new feature,
which is describled as in the datasheet, "WDT_MR can be written
until a LOCKMR command is issued in WDT_CR".
That is to say, as long as the bootstrap and u-boot don't issue
a LOCKMR command, WDT_MR can be written more than once in the driver.
So the SAMA5D4 watchdog driver's implementation is different from
the at91sam9260 watchdog driver implemented in file at91sam9_wdt.c.
The user application open the device file to enable the watchdog timer
hardware, and close to disable it, and set the watchdog timer timeout
by seting WDV and WDD fields of WDT_MR register, and ping the watchdog
by issuing WDRSTT command to WDT_CR register with hard-coded key.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The MPC5125 processor features a watchdog device that is identical to
the MPC8610 one. So allow to enable the driver for MPC512x kernel
configurations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer found in NXP LPC SoCs
family, which includes LPC18xx/LPC43xx. Other SoCs in that family may
share the same watchdog hardware.
Watchdog driver registers a restart handler that will restart the system
by performing an incorrect feed after ensuring the watchdog is enabled in
reset mode.
As watchdog cannot be disabled in hardware, driver's stop routine will
regularly send a keepalive ping using a timer.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The revision of the watchdog hardware in Sunrisepoint necessitates a new
"version" inside the TCO watchdog driver because some of the register
layouts have changed.
Also update the Kconfig entry to select both the LPC and SMBus drivers
since the TCO device is on the SMBus in Sunrisepoint.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In some situation, mainly when it's not possible to disable a
watchdog, you may want the watchdog driver to be started as soon
as possible.
Adding GPIO_WATCHDOG_ARCH_INITCALL to raise initcall from
module_init to arch_initcall.
This patch require watchdog registration deferral mechanism
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Not all architectures have io memory.
Fixes:
drivers/built-in.o: In function `cdns_wdt_probe':
cadence_wdt.c:(.text+0x33b7c9): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the ARM Kconfig dependency since the Maxim MAX63xx devices are
architecture independent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit add a driver for the watchdog functionality of the Conexant CX92755
SoC, from the Digicolor series of SoCs. Of 8 system timers provided by the
CX92755, the first one, timer A, can reset the chip when its counter reaches
zero. This driver uses this capability to provide userspace with a standard
watchdog, using the watchdog timer driver core framework. This driver also
implements a reboot handler for the reboot(2) system call.
The watchdog driver shares the timer registers with the CX92755 timer driver
(drivers/clocksource/timer-digicolor.c). The timer driver, however, uses only
timers other than A, so both drivers should coexist.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert OCTEON watchdog to WATCHDOG_CORE API. This enables support
for multiple watchdogs on OCTEON boards.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove Kconfig dependency and enable driver for
all ARCHs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use a syscon regmap to access the system timer registers.
Also, rename the driver atmel_st_watchdog to stop conflicting with
at91sam9_wdt.c
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
BCM5301X (ARCH_BCM_5301X) is a new Broadcom architecture using the same
SoC bus driver (bcma) as BCM47XX but based on ARM instead of MIPS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog functionality in both chips is almost identical to NCT6779.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
They need HAS_IOMEM, so let them depend on it, the related error (with
allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined!
ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUNZQwAAoJEMsfJm/On5mBxZEQAIf555P39+4fkRIrf3oYUuC2
q1tXNP0u8Z74eDFfwYYobt+NCJG5KW3H3kFaO5WCTjySfVwjUin9Fc6DkLl2m3U+
4FfH/2rO1y1upVRQemLAhe7BAYJAzABuNFWbLqqbGbZytyf5sHzhP52vjJ5VNmvr
5zcn/sGJdB5M9tj3isvfrac0itNu+D7K3qxknk4wI5gb6YzKg+uovXscPVx4Xa7w
eHKXJWITtBAZdD5bDV5YAzlTR15ASG3h+yyV7G5rKgslYyCMuRfIDm8Rl5zzHUmq
DjLwwib469NMii6CjdC7kEpYOgJ2ZxK/2XQ5IAeGax8GLdIHB6lhp3GrXIzzRwiW
5mtsMdRB7y41p050rIXN7AIXGVqSvtZtKf0r8w1p5YElat/wtX9gv0lGTgOq4sSa
0SOE7E6W0cfe75dYgJP/6HIkuZZ7PweBelQYDfWrN00u/rdIcwC2nRnW/nDbctkr
TmQLiS0ql2mXPWXD+Lk9v3bUALuYOPuQpX2aARj7en7jeBagP6KX0d70GaoAEzGk
Gw6z4X4gI3TasuIck4LZx3kaiijEnDOgnIaEQah4b3k7ABEiuOYVBBpnWvqECaSD
p9/lwFAs2POCsYSuADiclzxH6FLCMRJLE2V7dgMun9uK60o+0pGUqBL1PG/5/w+r
jGdB/75PCOEn3Y/VlfZg
=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
Added driver to support the 14F021P00 BMC Watchdog.
The BMC is a Board Management Controller including watchdog functionality.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The help text for DIAG288_WATCHDOG in drivers/watchdog/Kconfig
still mentioned the misleading old module name vmwatchdog.
This patch changes that to the correct new name diag288_wdt.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Add initial Intel MID watchdog driver support.
This driver is an initial implementation of generic Intel MID watchdog
driver. Currently it supports Intel Merrifield platform.
Signed-off-by: Eric Ernst <eric.ernst@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All three iop variants we support in Linux (iop32x, iop33x and
iop13xx) seem to have support for the watchdog hardware, but this
driver fails to build for the first two of these because it
uses the IOP13XX_WDTCR_IB_RESET macro that is only defined for
iop13xx.
This clarifies the dependency in Kconfig to avoid randconfig
build errors. It is unlikely that anyone will ever miss support
for this driver on the ancient iop3xx platforms, so we don't
need to bother trying to fix it properly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Since both chips are now supported by the w83627hf watchdog driver,
the chip specific drivers are no longer needed and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert the imx2_wdt driver to the new watchdog core api.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver will be working on IMX2+, Vybrid, LS1, LS2+
platforms, and will be in different endianness mode in those SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
IMX2+ LE LE
Vybird LE LE
LS1 LE BE
LS2 LE LE
Other possible SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
Soc1 BE BE
Soc2 BE LE
And also the watchdog's registers will be 32-bits for some versions,
and though it is 16-bits in IMX2+, Vybird and LS+.
Using the regmap APIs, could be more easy to support different
endianness and also more easy to support 32-bits version...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to its Kconfig help text, the sbc8360 watchdog driver is
only used on the Axiomtek SBC8360 single-board computer. This piece of
hardware is 32-bit x86 so the driver is useless beyond X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the LPAR variant of the diag 288 watchdog to the driver.
The only available action on timeout for LPAR is a PSW restart.
Signed-off-by: Philipp Hachtmann <phacht@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tomas Winkler
John Crispin
Mans Rullgard
Martyn Welch
Oleksij Rempel
Damien Riegel
Guo Zeng
Pratyush Anand
Shaohui Xie
Justin Chen
Guenter Roeck
Linus Torvalds
Wenyou Yang
Uwe Kleine-König
Ariel D'Alessandro
Matt Fleming
Jean-Baptiste Theou
S Twiss
Geert Uytterhoeven
Richard Weinberger
Vivien Didelot
Baruch Siach
Lee Jones
Aaro Koskinen
Michal Simek
Alexandre Belloni
Rafał Miłecki
Matthias Brugger
Naidu Tellapati
Nicolas Ferre
Chen Gang
Carlo Caione
Krystian Garbaciak
Beniamino Galvani
Josh Cartwright
Harini Katakam
Andreas Werner
Andrew Lunn
Philipp Hachtmann
David Cohen
Arnd Bergmann
Anatolij Gustschin
Xiubo Li
Jean Delvare
Philipp Hachtmann