Use of the cec notifier framework is required to support
CEC_CAP_CONNECTOR_INFO but some devices do not want physical address
updates from the notifier. This adds an option to allow registering
with a cec notifier without getting address updates.
[hans: document the new adap_controls_phys_addr bool]
Signed-off-by: Jeff Chase <jnchase@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ch7322 is a Chrontel CEC controller.
Signed-off-by: Jeff Chase <jnchase@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable err is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since components are registered in a list, the numeric component id that
specified a location in an array is not necessary.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions mtk_mdp_register/unregister_component have been created to
add / remove items from the list of components.
This will eventually enable us to specify a list of components in the
device tree instead of hardcoding them into this driver.
The list is modified by a single thread at driver probe time, and will
not be traversed by another thread until the call to pm_runtime_enable
at the end of probing.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These fields are not used and can be removed.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mtk-mdp driver uses states to check if the formats have been set
on the capture and output when turning the streaming on, setting
controls or setting the selection rectangles.
Those states are reset when 0 buffers are requested like when checking
capabilities.
This patch removes all format checks and set one by default as queues in
V4L2 are expected to always have a format set.
https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-streamon.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-ctrl.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-selection.html
Signed-off-by: Francois Buergisser <fbuergisser@chromium.org>
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If fw_csr_string() returns -ENOENT, then "name" is uninitialized. So
then the "strlen(model_names[i]) <= name_len" is true because strlen()
is unsigned and -ENOENT is type promoted to a very high positive value.
Then the "strncmp(name, model_names[i], name_len)" uses uninitialized
data because "name" is uninitialized.
Fixes: 92374e886c ("[media] firedtv: drop obsolete backend abstraction")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes coccicheck warning:
./drivers/media/platform/coda/coda-jpeg.c:331:3-31:
alloc with no test, possible model on line 354
Add NULL check after kmalloc.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently for msm_csiphy, msm_csid, and msm_ispif subdevices the media
entity function field is set to MEDIA_ENT_F_IO_V4L. This is incorrect
as MEDIA_ENT_F_IO_V4L implies V4L2 video node.
Change it to MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER as this is the best
fit from the functions defined in include/uapi/linux/media.h.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rkisp1 supports RGB encoding with 6 bits per
color with the following format:
- - b5 b4 b3 b2 b1 b0 - - g5 g4 g3 g2 g1 g0 - - r5 r4 r3 r2 r1 r0 - - - - - - - -
This is not how V4L2_PIX_FMT_BGR666 is defined, so remove
this format from the driver's formats list.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Syzbot reports a NULL-ptr deref in the kref_put() call:
BUG: KASAN: null-ptr-deref in media_request_put drivers/media/mc/mc-request.c:81 [inline]
kref_put include/linux/kref.h:64 [inline]
media_request_put drivers/media/mc/mc-request.c:81 [inline]
media_request_close+0x4d/0x170 drivers/media/mc/mc-request.c:89
__fput+0x2ed/0x750 fs/file_table.c:281
task_work_run+0x147/0x1d0 kernel/task_work.c:123
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_usermode_loop arch/x86/entry/common.c:165 [inline]
prepare_exit_to_usermode+0x48e/0x600 arch/x86/entry/common.c:196
What led to this crash was an injected memory allocation failure in
media_request_alloc():
FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 0
should_failslab+0x5/0x20
kmem_cache_alloc_trace+0x57/0x300
? anon_inode_getfile+0xe5/0x170
media_request_alloc+0x339/0x440
media_device_request_alloc+0x94/0xc0
media_device_ioctl+0x1fb/0x330
? do_vfs_ioctl+0x6ea/0x1a00
? media_ioctl+0x101/0x120
? __media_device_usb_init+0x430/0x430
? media_poll+0x110/0x110
__se_sys_ioctl+0xf9/0x160
do_syscall_64+0xf3/0x1b0
When that allocation fails, filp->private_data is left uninitialized
which media_request_close() does not expect and crashes.
To avoid this, reorder media_request_alloc() such that
allocating the struct file happens as the last step thus
media_request_close() will no longer get called for a partially created
media request.
Reported-by: syzbot+6bed2d543cf7e48b822b@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Fixes: 10905d70d7 ("media: media-request: implement media requests")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov2740 includes 512bytes of one-time programmable memory and
256 bytes are reserved for customers which can be used to store
customized information. This patch provide an NVMEM interface
to support read out the customized data in OTP.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The bus_type field of v4l2_fwnode_endpoint structure passed as the argument
to v4l2_fwnode_endpoint_alloc_parse() function must be initiaized.
Set it to V4L2_MBUS_CSI2_DPHY, and check for -ENXIO which is returned
when the requested media bus type doesn't match the fwnode.
Also remove v4l2_fwnode_endpoint field from struct imx290 as it is only
needed in the probe function: use the local variable for this purpose.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The 10ms settle time is needed only at the end of all consecutive
register writes. So move the delay to outside of the for loop of
imx290_set_register_array().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to enumerate all frame sizes supported by IMX290. This is
required for using with userspace tools such as libcamera.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX290 is capable of outputting frames in both Raw Bayer (packed) 10 and
12 bit formats. Since the driver already supports RAW10 mode, let's add
the missing RAW12 mode as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX290 operates with multiple link frequency and pixel rate combinations.
The initial driver used a single setting for both but since we now have
the lane count support in place, let's add configurable link frequency
and pixel rate.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit
adds support for 2 lane mode in addition to the 4 lane and also
configuring the data lane settings in the driver based on system
configuration.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The macro is defined as SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn),
so imx290_power_off must be the 1st arg, and imx290_power_on the 2nd.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
preview_init_entities() does not call v4l2_ctrl_handler_free() when
it fails.
Add the missed function to fix it.
Fixes: de1135d44f ("[media] omap3isp: CCDC, preview engine and resizer")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mccic_register() forgets to cleanup the notifier in its error handler.
mccic_shutdown() also misses calling v4l2_async_notifier_cleanup().
Add the missed calls to fix them.
Fixes: 3eefe36cc0 ("media: marvell-ccic: use async notifier to get the sensor")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the ACPI id of ov2740 camera sensor was registered as "INT3474",
current ov2740 driver is supposed to be working with ACPI only.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the convenience function pm_runtime_get_if_active() instead of a
number of calls to runtime PM to figure out if the device was already
powered up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When v4l2_async_register_subdev_sensor_common() returns
an error code, a pairing runtime PM usage counter
decrement is needed to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cec_adapter struct contained a waitq field that isn't used
anywhere, so drop this.
It also contained a phys_addrs array to store any reported physical
addresses. However, this was never actually used, so this field is
removed as well. The original idea was to let the core keep track of
this information, but nothing was ever done with this. Should this
be needed in the future then it is easy enough to resurrect this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CEC_ADAP_G_CAPS documentation of the cec_caps struct was missing
the available_log_addrs field. Add this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
budget_register() has no error handling after its failure.
Add the missed undo functions for error handling to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MyGica T230* receivers also do DVB-C and DVB-T: change their names.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CONFIG_DVB_USB_CXUSB_ANALOG is a 'bool' symbol with a dependency on the
tristate CONFIG_VIDEO_V4L2, which means it can be enabled as =y even
when its dependency is =m. This leads to a link failure:
drivers/media/usb/dvb-usb/cxusb-analog.o: In function `cxusb_medion_analog_init':
cxusb-analog.c:(.text+0x92): undefined reference to `v4l2_subdev_call_wrappers'
drivers/media/usb/dvb-usb/cxusb-analog.o: In function `cxusb_medion_register_analog':
cxusb-analog.c:(.text+0x466): undefined reference to `v4l2_device_register'
cxusb-analog.c:(.text+0x4c3): undefined reference to `v4l2_i2c_new_subdev'
cxusb-analog.c:(.text+0x4fb): undefined reference to `v4l2_subdev_call_wrappers'
...
Change the dependency only disallow the analog portion of the driver
in that configuration.
Fixes: e478d40540 ("media: cxusb: add analog mode support for Medion MD95700")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This has been maintained for some time, update MAINTAINERS to reflect.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IR Droid / IR Toy device used custom protocol over serial
line, so it is presenting itself as CDC ACM device.
Now that we have proper in-kernel driver for it we need to black-list the
device in cdc-acm driver.
http://dangerousprototypes.com/docs/USB_Infrared_Toyhttps://www.irdroid.com/irdroid-usb-ir-transceiver/
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media documents under the uAPI should be GFDL compatible.
So, make this one dual-licensed GPL-2.0 or GFDL-1.1+ with
no-invariant sections.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting the stateful encoder capture frame interval is only supported
if this flag is set. Document this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the V4L2_FMT_FLAG_ENC_CAP_FRAME_INTERVAL flag to signal that
the coded frame interval can be set separately from the raw frame
interval for stateful encoders.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add missing periods at the end of two sentences.
Although mandatory -> Although not mandatory
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This documentation is very outdated. In particular, it is
not obvious at all that this is used to change the framerate of
sensors.
Fix it, and include references to the stateful encoder API where
this works slightly different.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Due to complexity of the video encoding process, the V4L2 drivers of
stateful encoder hardware require specific sequences of V4L2 API calls
to be followed. These include capability enumeration, initialization,
encoding, encode parameters change, drain and reset.
Specifics of the above have been discussed during Media Workshops at
LinuxCon Europe 2012 in Barcelona and then later Embedded Linux
Conference Europe 2014 in Düsseldorf. The de facto Codec API that
originated at those events was later implemented by the drivers we already
have merged in mainline, such as s5p-mfc or coda.
The only thing missing was the real specification included as a part of
Linux Media documentation. Fix it now and document the encoder part of
the Codec API.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a cache_hints module param to control per-queue user space cache
hints support.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jeff Chase
Eugeniu Rosca
Colin Ian King
Eizan Miyamoto
Francois Buergisser
Dan Carpenter
Chen Zhou
Eugen Hristev
Gustavo A. R. Silva
Andrey Konovalov
Dafna Hirschfeld
Tuomas Tynkkynen
Qingwu Zhang
Manivannan Sadhasivam
Chuhong Yuan
Bingbu Cao
Sakari Ailus
Dinghao Liu
Hans Verkuil
Jia-Ju Bai
Jan Pieter van Woerkom
Arnd Bergmann
Sean Young
Mauro Carvalho Chehab
Tomasz Figa
Sergey Senozhatsky