The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A full HW reset is not required for all baseband watchdog
signatures. Some BB watchdog updates are benign and can
be discarded, some require re-programming of certain registers
and others require a chip reset.
This patch adds a routine to identify such signatures.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for adding separate hang check
routines for AR9002 and AR9003.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW hang checks have to be done on a per-chip basis.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw should not depend on any ath9k data structures like ath_softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused fields, pass timer info in usec instead of TU.
Preparation for fixing nexttbtt calculation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM
data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware does not have support for ATIM processing, and the driver
does not set up ah->atim_window anywhere. Additionally, the code can
clobber the timer used by P2P powersave.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Use generic bitops instead of custom hackery
- Move interrupt enable/disable logic from ath9k to ath9k_hw
- Decouple ISR call from btcoex
- Make the overflow callback optional (to prevent IRQ storms)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.
By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.
The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This HW config option is always set to true and is not needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the PLL is turned off for AR9485 when
switching to a low power state, but AR9485 has an issue
where the card will become unresponsive if left idle
for a long time without any traffic. To fix this,
force the PLL to always be on using a different initval
array, ar9485_1_1_pll_on_cdr_on_clkreq_disable_L1.
This is done for most of the AR9485 based cards
like HB125, WB225 etc. but certain models require the
feature to be turned off. Identify such cards and use
default values for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.
Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.
In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:
http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates
Example usage:
iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up
iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4
echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing it to get the current operating channel is racy and in the way
of further channel handling related changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some duplication between channelFlags and chanmode, as well as
a lot of redundant checks based on the combinations of flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware is always configured with OFDM support enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware 802.11b-only mode isn't supported by the driver (the device is
configured for 802.11n/g instead). Simplify the code by removing checks
for it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use wrappers where available. Simplifies code and helps with further
improvements to the channel data structure
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:
* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.
Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the L1 entrance latency is not calibrated properly
in the EEPROM in WB222 boards, there could be problems
in connectivity. Check and correct the calibrated value
if it doesn't match the optimal value for WB222, 4us.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves RX diversity and performance for AR9485.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.
Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "ath9k_hw_set_bt_ant_diversity" instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This flag is used for indicating channel interference and
we currently do nothing with it, so remove it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are no longer needed for ANI functionality
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan
Felix Fietkau
Luis R. Rodriguez
Zefir Kurtisi
John W. Linville