This patch adds basic support for monitor mode. Also change the open
call that we set the transceiver mac setting on an interface up. Futher
patches will add a better handling while interface up an interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds error handling after skb_clone and deliver only if
skb_clone was successful.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the !netif_running(sdata->dev) instead we doing a
!ieee802154_sdata_running(sdata). Also move this in two separate if
branches to compare with mac80211 code.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds rx stats incrementation when the monitor interface
recevied a frame.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes netif_rx_ni call. Instead we call netif_receive_skb,
we can do that since commit c5c47e67bc
("mac802154: rx: use tasklet instead workqueue").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes pkt_type set to PACKET_HOST while monitor receiving.
This should be PACKET_OTHERHOST on monitor mode which already set
before.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new hardware flag which indicate that the transceiver
doesn't support check for bad checksum via hardware. Also add a handling of
this while receive.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the actual crc handling while receive. Currently the
IEEE802154_HW_RX_OMIT_CKSUM flag is used to filter a frame with a bad crc.
This patch changes the behaviour of IEEE802154_HW_RX_OMIT_CKSUM to add a
crc while receiving for the monitor interface. After monitor receiving
we remove the crc for frame parsing. This affect the driver layer
because all drivers sets IEEE802154_HW_RX_OMIT_CKSUM and deliver without
checksum.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes a not used parameter in ieee802154_deliver_skb.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch splits the IEEE802154_HW_OMIT_CKSUM hardware flag into
IEEE802154_HW_TX_OMIT_CKSUM and IEEE802154_HW_RX_OMIT_CKSUM. This is
useful to deliver the received crc from the driver layer to the monitor
interface. At the moment we can't do that without change the xmit
handling.
The received checksum should be visible in monitor mode only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new driver operation to bring the transceiver into
promiscuous mode.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes an unnecessary include of driver-ops header file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the open_count variable increment in open and close
calls of netdev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions can be static in mac_cmd file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These channel attributes was part of "channel context switch while xmit"
which was removed by commit dc67c6b30f
("mac802154: tx: remove xmit channel context switch"). This patch
removes these unnecessary variables and use the current_page and
current_channel by wpan_phy struct now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These variables should already be zero, so we remove the extra assign to
zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds synchronization handling in start and stop driver ops
calls. This patch is mostly grab from mac80211 which was introduced by
commit ea77f12f2c ("mac80211: remove
tasklet enable/disable"). This is to be sure that we don't run into same
issues.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the current handling of started boolean. This is
actually dead code, because mac802154_netdev_register can't never be
called before ieee802154_register_hw. This means that local->started is
always be true when mac802154_netdev_register is called. Instead we
using this now like mac80211 to indicate that an instance of sdata is
running.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This variable should be handled like ieee80211_local struct of mac80211.
We rename this variable to started now to have the same name convention.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the handling for setting the state like mac80211. We
use bit's instead a bool variable. The mutex is not needed because it use
test and set bits which are atomic operations.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the driver ops callbacks inside of wpan_phy struct.
It was used to check if a phy supports this driver ops call. We do this
now via hardware flags.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces all directly called driver ops by previous
introduced driver-ops function wrappers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a driver-ops header file with function wrappers to
call the driver ops. These wrappers checking on right context
information and warn if optional driver ops are called when these aren't
implemented. This behaviour is like mac80211 driver-ops header file,
just without function tracing calls.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions can be static inside the iface file, because it's not
used anywhere else. This patch moves these functions into iface file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the monitor implementation file and put all monitor
stuff into iface file. It's now small enough to put all necessary
handling into iface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the naming convention of mac802154 rx file. It should
be more named like mac80211 stack. Furthermore we introduce a new frame
parsing implementation which is much similar the mac80211
implementation.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of twice lock and unlock mechanism this patch hold these locks
only once at one position.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the skb_reset_mac_header call before frame parsing
while wpan rx and before monitor deliver functionality.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a PACKET_OTHERHOST setting when a monitor interface
receives a skb. All receiving skb's to the monitor interface should
be PACKET_OTHERHOST.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds CHECKSUM_UNNECESSARY to skb->ip_summed before delivery.
There exist no transceiver with IP checksum functionality.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the skb->protocol setting to the position when it's
needed. It's only needed when frame parsing was successful.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the mac802154_subif_rx function and do the necessary
calls inside of ieee802154_rx function. The ieee802154_rx is small
enough to move the functionality inside this function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This removes the call of monitor receive funktion when any interface
type call xmit. There exist no such use case that a monitor interface
should receive the actual sending frame. One use case could be that a
wpan interface and monitor interface could be running at the same time
on one phy. Then the monitor interface receives the wpan frames also.
Furthermore we adding support for promiscous mode setting. With
promiscous mode setting we can't run a wpan and monitor interface at the
same time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes all relevant receiving functions inclusive frame
parsing into rx file. Like mac80211 we should implement the complete
receive handling and parsing in this file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is similar like d20ef63d32
("mac80211: document ieee80211_rx() context requirement"). The
netif_receive_skb call requires with softirqs disabled. This patch
adds a warning if softirqs are pending while calling ieee802154_rx.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tasklets have much less overhead than workqueues. This patch also
removes the heap allocation for the worker on receiving path.
Like mac80211 we should prefer use a tasklet here instead a workqueue to
getting fast out of interrupt context when ieee802154_rx_irqsafe is
called by driver. Like wireless inside the tasklet context we should
call netif_receive_skb instead netif_rx_ni anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the memcpy with a put_unaligned_le16. The placement
of crc inside of PSDU can also be unaligned. With memcpy this can fail
on some architectures.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the worker information struct out of skb control block.
Instead control block we declare it static inside of tx.c file. We can do
that, because the worker can't be used twice at the same time. It's
protected by stop and wake netdev queue.
This patch fix an issue that the "struct ieee802154_xmit_cb" doesn't fit
into the skb control block on some kernel configuartion reported by
kbuild test robot.
It was introduced by commit fe24371d66
("mac802154: tx: remove kmalloc in xmit hotpath").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the naming convention of the tx functions like
mac80211. Just with an 802154 instead 80211 inside the name.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the stats increment of successful transmitted packets
in the right place when the skb was really successful transmitted.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the pr_foo printout function to netdev_foo printout
function. Inside the xmit handling, the interface is already known.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch holds rtnl lock while sync xmit inside of workqueue.
Otherwise we could down the interface while worker xmit handling.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the existsing xmit callback to xmit_sync and
introduces an asynchronous xmit_async function. If ieee802154_ops
doesn't provide the xmit_async callback, then we have a fallback to
the xmit_sync callback.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of an error we should call kfree_skb instead of consume_skb which
is called by ieee802154_xmit_complete function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch uses the queue utility helpers inside the xmit worker of
mac802154 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new file net/mac802154/util.c which contains utility
functions for drivers, etc. This file contains functions to start and
stop queues for all virtual interfaces, this is useful for asynchronous
handling by driver level.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the channel hopping feature before xmit. There are
several issues to provide a real channel hopping (timing requirements,
etc...).
We don't have any known kernelspace protocol which really use this
feature. And I don't know an real user of this feature.
We simply drop this feature now.
This patch removes also the hold of pib lock which isn't needed by any
real driver xmit callback implementation.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce some new stack variables to avoid multiple
dereferencing inside the xmit worker function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the kmalloc allocation for workqueue data. This patch
replaces the kmalloc and uses the control block of skb. The control block
has enough space and isn't use by any other layer in this case.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the netdev xmit callback functions into the tx.c file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver_ops callback function is never used by any driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Small rename to use the name workqueue than dev_workqueue. To bring the
same naming convention like wireless into 802.15.4.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This function adds a wrapper to call netdev_priv to getting the sdata
attribute. This is similar like the IEEE80211_DEV_TO_SUB_IF function
inside wireless stack implementation.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the mac802154_to_priv macro with a static inline
function named hw_to_local. This brings a similar naming convention like
mac80211 stack.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renamens the slaves attribute in sdata to interfaces and
slaves_mtx to iflist_mtx. This is similar like the mac80211 stack naming
convention.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the hw attribute in struct ieee802154_sub_if_data to
local. This avoid confusing with the struct ieee802154_hw hw; inside of
local struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Like wireless this structure should named ieee802154_sub_if_data and not
mac802154_sub_if_data. This patch renames the struct and variables to
sdata instead priv sometimes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch rename the mac802154_priv to ieee802154_local. The
mac802154_priv structure is like ieee80211_local and so we name it
ieee802154_local.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identical struct of the wireless stack implementation is named
ieee80211_hw. This is useful to name the variable hw instead of get
confusing with netdev dev variable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the ieee802154 header into include/linux instead
include/net. Similar like wireless which have the ieee80211 header
inside of include/linux.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wpan-phy header contains the wpan_phy struct information. Later this
header will be have similar function like cfg80211 header. The cfg80211
header contains the wiphy struct which is identically the wpan_phy
struct inside 802.15.4 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wpan.c file contains the interface handling functions now. It's similar
like the mac80211 iface.c file. This patch renames this file to iface.c to
have similar naming convention in mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the mac802154.h internal header to ieee802154_i.h like
the wireless stack ieee80211_i.h file. This avoids confusing with the
not internal header include/net/mac802154.h header. Additional we get
the same naming conversion like mac80211 for this file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_dev functionality contains various function for
allocation and registration of an ieee802154_dev. This is equal to the
net/mac80211/main.c file. This patch rename the ieee802154_dev.c to
main.c to have the same behaviour.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixs a typo in address filter defines from IEEE802515 to
IEEE802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix a typo and fix align instead allign.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If received frame contains the reserved destination address mode. The
frame should be dropped and free the skb.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix a memory leak if received frame was not able to parse.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce the common error path on failure of Tx by
inserting the label 'err_tx'.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By introducing label fail, making the common error path for
mac802154_llsec_decrypt() and packet type default case.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the sizeof(struct rx_work) with sizeof(*work)
and directly passing the skb in mac802154_subif_rx()
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the coding style issues reported by checkpatch.pl
following issues fixed:
CHECK: Alignment should match open parenthesis
WARNING: line over 80 characters
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: networking block comments don't use an empty /* line, use /* Comment...
WARNING: Missing a blank line after declarations
WARNING: networking block comments start with * on subsequent lines
CHECK: braces {} should be used on all arms of this statement
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one WPAN devices can be active at any given time, so only deliver
packets to that one interface that is actually up. Multiple monitors may
be up at any given time, but we don't have to deliver to monitors that
are down either.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac802154 RX did not free skbs on decryption failure, assuming that the
caller would when the local rx handler returned _DROP. This was false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
During key removal, the key object is freed, but not taken out of the
llsec key list properly. Fix that.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key id comparison for type 1 keys (implicit source, with index) should
return true if mode and id are equal, not false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
llsec_do_encrypt will never return a positive value, so the restriction
to 0-or-negative on return is useless.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In encrypt, sec->lock is taken with read_lock_bh, so in the error path,
we must read_unlock_bh.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.15.4-2011 standard states that for each key, a list of devices
that use this key shall be kept. Previous patches have only considered
two options:
* a device "uses" (or may use) all keys, rendering the list useless
* a device is restricted to a certain set of keys
Another option would be that a device *may* use all keys, but need not
do so, and we are interested in the actual set of keys the device uses.
Recording keys used by any given device may have a noticable performance
impact and might not be needed as often. The common case, in which a
device will not switch keys too often, should still perform well.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds containers and mutators for the major ieee802154_llsec
structures to mac802154. Most of the (rather simple) ieee802154_llsec
structs are wrapped only to provide an rcu_head for orderly disposal,
but some structs - llsec keys notably - require more complex
bookkeeping.
Since each llsec key may be referenced by a number of llsec key table
entries (with differing key ids, but the same actual key), we want to
save memory and not allocate crypto transforms for each entry in the
table. Thus, the mac802154 llsec key is reference-counted instead.
Further, each key will have four associated crypto transforms - three
CCM transforms for the authsizes 4/8/16 and one CTR transform for
unauthenticated encryption. If we had a CCM* transform that allowed
authsize 0, and authsize as part of requests instead of transforms, this
would not be necessary.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link-layer security requires AES CCM for authenticated modes and AES CTR
for the unauthenticated encryption mode.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only used within the same translation unit, so mark it
static.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mac_cb handling of ieee802154 is rather awkward and limited.
Decompose the single flags field into multiple fields with the meanings
of each subfield of the flags field to make future extensions (for
example, link-layer security) easier. Also don't set the frame sequence
number in upper layers, since that's a thing the MAC is supposed to set
on frame transmit - we set it on header creation, but assuming that
upper layers do not blindly duplicate our headers, this is fine.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current WPAN header creation code checks for EMSGSIZE conditions,
but does not account for the MIC field that link layer security may add
at the end of the frame. Now that we can accurately calculate the
maximum payload size of packets, use that to check for EMSGSIZE
conditions.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit e6278d9200 ("mac802154: use header operations to
create/parse headers") included the header
net/ieee802154_netdev.h
which had been included by the commit b70ab2e87f ("ieee802154:
enforce consistent endianness in the 802.15.4 stack"). Fix this
duplicate #include by deleting the latter one as the required header
has already been in place.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Cc: linux-zigbee-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b2777d608 (ieee802154: add TX power control to wpan_phy)
and following erroneously added CSMA and CCA parameters for 802.15.4
devices as PHY parameters, while they are actually MAC parameters and
can differ for any two WPAN instances. Since it is now sensible to have
multiple WPAN devices with differing CSMA/CCA parameters, make these
parameters MAC parameters instead.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 802.15.4 PHY devices with drivers in tree can support only one WPAN
at any given time, yet the stack allows arbitrarily many WPAN devices to
be created and up at the same time. This cannot work with what the
hardware provides, and in the current implementation, provides an easy
DoS vector to any process on the system that may call socket() and
sendmsg().
Thus, allow only one WPAN per PHY to be up at once, just like mac80211
does for managed devices.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mac802154 header_ops.create fail with -EMSGSIZE if the length
passed will be too large to fit a frame. Since 6lowpan will ensure that
no packet payload will be too large, pass a length of 0 there. 802.15.4
dgram sockets will also return -EMSGSIZE on payloads larger than the
device MTU instead of -EINVAL.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all internal uses of ieee802154_addr_sa to ieee802154_addr,
except for those instances that communicate directly with userspace.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the operations on 802.15.4 header structs introduced in a previous
patch to create and parse all headers in the mac802154 stack. This patch
reduces code duplication between different parts of the mac802154 stack
that needed information from headers, and also fixes a few bugs that
seem to have gone unnoticed until now:
* 802.15.4 dgram sockets would return a slightly incorrect value for
the SIOCINQ ioctl
* mac802154 would not drop frames with the "security enabled" bit set,
even though it does not support security, in violation of the
standard
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.
Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new netlink attributes for SET_PHY_ATTRS:
* CSMA minimal backoff exponent
* CSMA maximal backoff exponent
* CSMA retry limit
* frame retransmission limit
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpath.pl:
WARNING: Prefer pr_warn(... to pr_warning(...
#447: FILE: ./wpan.c:447:
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the mac header length while creating the 802.15.4 mac header.
Drop the function for recalculate mac header length in upper layers
which was static and works for intra pan communication only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change MAC802154_CHAN_NONE from ~(u8)0 to 0xff, or the comparison in
mac802154_wpan_xmit() for ``chan == MAC802154_CHAN_NONE'' will not
succeed.
This bug can be boiled down to ``u8 foo = 0xff; if (foo == ~(u8)0)
[...] else [...]'' where the condition will always take the else
branch.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two sections checked whether the current channel != the new channel
without ever setting the current channel variables.
1. net/mac802154/tx.c: Prevent set_channel() from getting called every
time a packet is sent.
2. net/mac802154/mib.c: Lock (pib_lock) accesses to current_channel and
current_page and make sure they are updated when the channel has been
changed.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the buffer length from 10 to 300 packets. Consider that traffic on
mac802154 devices will often be 6LoWPAN, and a full-length (1280 octet)
IPv6 packet will fragment into 15 6LoWPAN fragments (because the MTU of
IEEE 802.15.4 is 127). A 300-packet queue is really 20 full-length IPv6
packets.
With a queue length of 10, an entire IPv6 packet was unable to get queued
at one time, causing fragments to be dropped, and making reassembly
impossible.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_stop_queue() and netif_wake_queue() to control the flow of
packets to mac802154 devices. Since many IEEE 802.15.4 devices have no
output buffer, and since the mac802154 xmit() function is designed to
block, netif_stop_queue() is called after each packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ops->xmit() fails, drop the packet. Devices which support hardware
ack and retry (which include all devices currently supported by mainline),
will automatically retry sending the packet (in the hardware) up to 3
times, per the 802.15.4 spec. There is no need, and it is incorrect to
try to do it in mac802154.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring-over mac802154_dev_get_dsn() function that was present in the
Linux ZigBee kernel. This function is called by the 6LoWPAN code in
order to properly set the DSN (Data Sequence Number) value in the IEEE
802.15.4 frame.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
head buffer is only temporary available in mac802154_header_create.
So it's not necessary to put it on the heap.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
When using nanosleep() in an userspace application we get a
ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
This patch replaces netif_rx() with netif_rx_ni() which has
to be used from process/softirq context.
The process/softirq context will be called from fakelb driver.
See linux-kernel commit 481a819 for similar fix.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mutex_destroy() must be called before wpan_phy_free(), because it puts the last
reference and frees memory. Catched as overwritten poison in kmalloc-2048.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-zigbee-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb() indicates failure, which is where this is being used.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb() was not getting called in the case of some failures.
This was pointed out by Eric Dumazet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make symbols static to avoid the following warning shown up
by sparse:
warning: symbol ... was not declared. Should it be static?
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add method to get the device short 802.15.4 address. This call
needed by ieee802154 layer to satisfy 'iz list' request from
the user space.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add monitor receive callback to the TX datapath to catch all the
data sent to transceivers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic preparations to start the interface.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new method to set page and channel values for a transceiver
was added to the MIB.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A method to assign the IEEE802.15.4 short address was added to the
MIB implementation.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two methods intended to get and set the Private Area Network identifier
were added to the MIB implementation.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every real 802.15.4 transceiver, which works with software MAC layer,
can be classified as a wpan device in this stack. So the wpan device
implementation provides missing link in datapath between the device
drivers and the Linux network queue.
According to the IEEE 802.15.4 standard each packet can be one of the
following types:
- beacon
- MAC layer command
- ACK
- data
This patch adds support for the data packet-type only, but this is
enough to perform data transmission and receiving over radio.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed braces after 'if' operator.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for monitor device intended to capture all the network activity.
This interface could be used by networks sniffers and is already
supported by WireShark. That's a good test point to check that basic
MAC support works.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality for registration and removing slaves
in the stack.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic support for IEEE 802.15.4 management information base.
Current implementation contains a command to set HW address only.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare set of MAC-commands for reduced functionality interface.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slaves represent typical network interfaces available from userspace.
Each ieee802154 device/transceiver may have several slaves and able
to be associated with several networks at the same time. So this
patch adds structure for slaves declaration.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main TX data path implementation between upper and physical layers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main RX data path implementation between physical and mac layers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An interface to allocate and register ieee802154 compatible device.
The allocated device has the following representation in memory:
+-----------------------+
| struct wpan_phy |
+-----------------------+
| struct mac802154_priv |
+-----------------------+
| driver's private data |
+-----------------------+
Used by device drivers to register new instance in the stack.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring
Julien Catalano
Linus Torvalds
John W. Linville
Masanari Iida
Martin Townsend
Varka Bhadram
Tom Gundersen
Varka Bhadram
Phoebe Buckheister
Jean Sacren
stephen hemminger
Weilong Chen
David S. Miller
Chen Gang
Alan Ott
Tony Cheneau
Kees Cook
Alexander Aring
Konstantin Khlebnikov
alex.bluesman.smirnov@gmail.com