Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/imx53-ppd.dt.yaml
CHECK arch/arm/boot/dts/imx53-ppd.dt.yaml
arch/arm/boot/dts/imx53-ppd.dt.yaml: leds-brightness: 'alarm-brightness' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml
CHECK arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml
arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml: pwmleds: 'blue', 'green', 'red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use kernel LED interface for the alarm LEDs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.
At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'num-chipselects' property is not a valid property according
to Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt, so
let's remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Single child nodes in OF graph don't need an address and now dtc will
warn about this:
Warning (graph_child_address): /soc/aips@50000000/ldb@53fa8008/lvds-channel@0: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Since the LDB should always have an output port, fix the warning by
adding the output port, 2, to the DT.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds
Linus Walleij
Alexander Dahl
Uwe Kleine-König
Ian Ray
Rob Herring
Fabio Estevam
Sebastian Reichel
Fabio Estevam
Martyn Welch
Fabien Lahoudere