Since commit 2b279c0348 ("powerpc/32s: Allow mapping with BATs with
DEBUG_PAGEALLOC"), there is no real situation where mapping without
BATs is required.
In order to simplify memory handling, always map kernel text
and rodata with BATs even when "nobats" kernel parameter is set.
Also fix the 603 TLB miss exceptions that don't require anymore
kernel page table if DEBUG_PAGEALLOC.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/da51f7ec632825a4ce43290a904aad61648408c0.1606285013.git.christophe.leroy@csgroup.eu
When a TLB Invalidate is required for the Logical Partition, the following
sequence has to be performed:
1. Load MMIO ATSD AVA register with the necessary value, if required.
2. Write the MMIO ATSD launch register to initiate the TLB Invalidate
command.
3. Poll the MMIO ATSD status register to determine when the TLB Invalidate
has been completed.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201125155013.39955-3-clombard@linux.vnet.ibm.com
Platform specific function to assign a register set to a Logical Partition.
The "ibm,mmio-atsd" property, provided by the firmware, contains the 16
base ATSD physical addresses (ATSD0 through ATSD15) of the set of MMIO
registers (XTS MMIO ATSDx LPARID/AVA/launch/status register).
For the time being, the ATSD0 set of registers is used by default.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201125155013.39955-2-clombard@linux.vnet.ibm.com
PowerISA v3.1 introduces new control bit (PMCCEXT) for restricting
access to group B PMU registers in problem state when
MMCR0 PMCC=0b00. In problem state and when MMCR0 PMCC=0b00,
setting the Monitor Mode Control Register bit 54 (MMCR0 PMCCEXT),
will restrict read permission on Group B Performance Monitor
Registers (SIER, SIAR, SDAR and MMCR1). When this bit is set to zero,
group B registers will be readable. In other platforms (like power9),
the older behaviour is retained where group B PMU SPRs are readable.
Patch adds support for MMCR0 PMCCEXT bit in power10 by enabling
this bit during boot and during the PMU event enable/disable callback
functions.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-8-git-send-email-atrajeev@linux.vnet.ibm.com
Export l2l3 events (PM_L2_ST_MISS and PM_L2_ST) and LLC-prefetches
(PM_L3_PF_MISS_L3) via sysfs, and also add these to list of
cache_events.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-7-git-send-email-atrajeev@linux.vnet.ibm.com
Fix the event code for events: branch-instructions (to PM_BR_FIN),
branch-misses (to PM_MPRED_BR_FIN) and cache-misses (to
PM_LD_DEMAND_MISS_L1_FIN) for power10 PMU. Update the
list of generic events with this modified event code.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-6-git-send-email-atrajeev@linux.vnet.ibm.com
There are event code updates for some of the generic events
and cache events for power10. Inorder to maintain the current
event codes work with DD1 also, create a new array of generic_events,
cache_events and pmu_attr_groups with suffix _dd1, example,
power10_events_attr_dd1. So that further updates to event codes
can be made in the original list, ie, power10_events_attr. Update the
power10 pmu init code to pick the dd1 list while registering
the power PMU, based on the pvr (Processor Version Register) value.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-5-git-send-email-atrajeev@linux.vnet.ibm.com
The PMU group constraints mask for threshold events covers
all thresholding bits which includes threshold control value
(start/stop), select value as well as thresh_cmp value (MMCRA[9:18].
In power9, thresh_cmp bits were part of the event code. But in case
of power10, thresh_cmp bits are not part of event code due to
inclusion of MMCR3 bits. Hence thresh_cmp is not valid for
group constraints for power10.
Fix the PMU group constraints checking for threshold events in
power10 by using constraint mask and value for only threshold control
and select bits.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-4-git-send-email-atrajeev@linux.vnet.ibm.com
In Power9, L2/L3 bus events are always available as a
"bank" of 4 events. To obtain the counts for any of the
l2/l3 bus events in a given bank, the user will have to
program PMC4 with corresponding l2/l3 bus event for that
bank.
Commit 59029136d7 ("powerpc/perf: Add constraints for power9 l2/l3 bus events")
enforced this rule in Power9. But this is not valid for
Power10, since in Power10 Monitor Mode Control Register2
(MMCR2) has bits to configure l2/l3 event bits. Hence remove
this PMC4 constraint check from power10.
Since the l2/l3 bits in MMCR2 are not per-pmc, patch handles
group constrints checks for l2/l3 bits in MMCR2.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-3-git-send-email-atrajeev@linux.vnet.ibm.com
power10 uses bit 9 of the raw event code as RADIX_SCOPE_QUAL.
This bit is used for enabling the radix process events.
Patch fixes the PMU counter support functions to program bit
18 of MMCR1 ( Monitor Mode Control Register1 ) with the
RADIX_SCOPE_QUAL bit value. Since this field is not per-pmc,
add this to PMU group constraints to make sure events in a
group will have same bit value for this field. Use bit 21 as
constraint bit field for radix_scope_qual. Patch also updates
the power10 raw event encoding layout information, format field
and constraints bit layout to include the radix_scope_qual bit.
Fixes: a64e697cef ("powerpc/perf: power10 Performance Monitoring support")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-2-git-send-email-atrajeev@linux.vnet.ibm.com
If FTR_BOOK3S_KUAP is disabled, kernel will continue to run with the same AMR
value with which it was entered. Hence there is a high chance that
we can return without restoring the AMR value. This also helps the case
when applications are not using the pkey feature. In this case, different
applications will have the same AMR values and hence we can avoid restoring
AMR in this case too.
Also avoid isync() if not really needed.
Do the same for IAMR.
null-syscall benchmark results:
With smap/smep disabled:
Without patch:
957.95 ns 2778.17 cycles
With patch:
858.38 ns 2489.30 cycles
With smap/smep enabled:
Without patch:
1017.26 ns 2950.36 cycles
With patch:
1021.51 ns 2962.44 cycles
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-23-aneesh.kumar@linux.ibm.com
With hash translation use DSISR_KEYFAULT to identify a wrong access.
With Radix we look at the AMR value and type of fault.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-17-aneesh.kumar@linux.ibm.com
If an application has configured address protection such that read/write is
denied using pkey even the kernel should receive a FAULT on accessing the same.
This patch use user AMR value stored in pt_regs.amr to achieve the same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-16-aneesh.kumar@linux.ibm.com
Now that kernel correctly store/restore userspace AMR/IAMR values, avoid
manipulating AMR and IAMR from the kernel on behalf of userspace.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-15-aneesh.kumar@linux.ibm.com
On fork, we inherit from the parent and on exec, we should switch to default_amr values.
Also, avoid changing the AMR register value within the kernel. The kernel now runs with
different AMR values.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-13-aneesh.kumar@linux.ibm.com
Child thread.kuap value is inherited from the parent in copy_thread_tls. We still
need to make sure when the child returns from a fork in the kernel we start with the kernel
default AMR value.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-12-aneesh.kumar@linux.ibm.com
This prepare kernel to operate with a different value than userspace AMR/IAMR.
For this, AMR/IAMR need to be saved and restored on entry and return from the
kernel.
With KUAP we modify kernel AMR when accessing user address from the kernel
via copy_to/from_user interfaces. We don't need to modify IAMR value in
similar fashion.
If MMU_FTR_PKEY is enabled we need to save AMR/IAMR in pt_regs on entering
kernel from userspace. If not we can assume that AMR/IAMR is not modified
from userspace.
We need to save AMR if we have MMU_FTR_BOOK3S_KUAP feature enabled and we are
interrupted within kernel. This is required so that if we get interrupted
within copy_to/from_user we continue with the right AMR value.
If we hae MMU_FTR_BOOK3S_KUEP enabled we need to restore IAMR on
return to userspace beause kernel will be running with a different
IAMR value.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-11-aneesh.kumar@linux.ibm.com
In later patches during exec, we would like to access default regs.amr to
control access to the user mapping. Having thread.regs set early makes the
code changes simpler.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-10-aneesh.kumar@linux.ibm.com
This patch updates kernel hash page table entries to use storage key 3
for its mapping. This implies all kernel access will now use key 3 to
control READ/WRITE. The patch also prevents the allocation of key 3 from
userspace and UAMOR value is updated such that userspace cannot modify key 3.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-9-aneesh.kumar@linux.ibm.com
This is in preparation to adding support for kuap with hash translation.
In preparation for that rename/move kuap related functions to
non radix names. Also move the feature bit closer to MMU_FTR_KUEP.
MMU_FTR_KUEP is renamed to MMU_FTR_BOOK3S_KUEP to indicate the feature
is only relevant to BOOK3S_64
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-8-aneesh.kumar@linux.ibm.com
The next set of patches adds support for kuep with hash translation.
In preparation for that rename/move kuap related functions to
non radix names.
Also set MMU_FTR_KUEP and add the missing isync().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-7-aneesh.kumar@linux.ibm.com
The next set of patches adds support for kuap with hash translation.
In preparation for that rename/move kuap related functions to
non radix names.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-6-aneesh.kumar@linux.ibm.com
This patch consolidates UAMOR update across pkey, kuap and kuep features.
The boot cpu initialize UAMOR via pkey init and both radix/hash do the
secondary cpu UAMOR init in early_init_mmu_secondary.
We don't check for mmu_feature in radix secondary init because UAMOR
is a supported SPRN with all CPUs supporting radix translation.
The old code was not updating UAMOR if we had smap disabled and smep enabled.
This change handles that case.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-5-aneesh.kumar@linux.ibm.com
The config CONFIG_PPC_PKEY is used to select the base support that is
required for PPC_MEM_KEYS, KUAP, and KUEP. Adding this dependency
reduces the code complexity(in terms of #ifdefs) and enables us to
move some of the initialization code to pkeys.c
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-4-aneesh.kumar@linux.ibm.com
With power7 and above we expect the cpu to support keys. The
number of keys are firmware controlled based on device tree.
PR KVM do not expose key details via device tree. Hence when running with PR KVM
we do run with MMU_FTR_KEY support disabled. But we can still
get updates on UAMOR. Hence ignore access to them and for mfstpr return
0 indicating no AMR/IAMR update is no allowed.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201127044424.40686-3-aneesh.kumar@linux.ibm.com
Since ISA v3.0, SLB no longer uses the slb_cache, and stab_rr is no
longer correlated with SLB allocation. Move those to pre-3.0.
While here, improve some alignments and reduce whitespace.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-9-npiggin@gmail.com
"Host" caused machine check is printed when the kernel sees a MCE
hit in this kernel or userspace, and "Guest" if it hit one of its
guests. This is confusing when a guest kernel handles a hypervisor-
delivered MCE, it also prints "Host".
Just remove "Host". "Guest" is adequate to make the distinction.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-8-npiggin@gmail.com
Don't treat ERAT MCEs as SLB, don't save the SLB and use a specific
ERAT flush to recover it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-7-npiggin@gmail.com
Harmless HMI errors can be triggered by guests in some cases, and don't
contain much useful information anyway. Ratelimit these to avoid
flooding the console/logs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use dedicated ratelimit state, not printk_ratelimit()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-6-npiggin@gmail.com
A number of machine check exceptions are triggerable by the guest.
Ratelimit these to avoid a guest flooding the host console and logs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use dedicated ratelimit state, not printk_ratelimit()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-5-npiggin@gmail.com
Guests that can deal with machine checks would actually prefer the
hypervisor not to try recover for them. For example if SLB multi-hits
are recovered by the hypervisor by clearing the SLB then the guest
will not be able to log the contents and debug its programming error.
If guests don't register for FWNMI, they may not be so capable and so
the hypervisor will continue to recover for those.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-4-npiggin@gmail.com
KVM has strategies to perform machine check recovery. If a MCE hits
in a guest, have the low level handler just decode and save the MCE
but not try to recover anything, so KVM can deal with it.
The host does not own SLBs and does not need to report the SLB state
in case of a multi-hit for example, or know about the virtual memory
map of the guest.
UE and memory poisoning of guest pages in the host is one thing that
is possibly not completely robust at the moment, but this too needs
to go via KVM (possibly via the guest and back out to host via hcall)
rather than being handled at a low level in the host handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201128070728.825934-3-npiggin@gmail.com
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. For the shutdown callback
it's ps3_system_bus_shutdown() which ignores the return value.
To simplify the quest to make struct device_driver::remove return void,
let struct ps3_system_bus_driver::remove return void, too. All users
already unconditionally return 0, this commit makes it obvious that
returning an error code is a bad idea and ensures future users behave
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126165950.2554997-2-u.kleine-koenig@pengutronix.de
Introduce a static branch that would be set during boot if the OS
happens to be a KVM guest. Subsequent checks to see if we are on KVM
will rely on this static branch. This static branch would be used in
vcpu_is_preempted() in a subsequent patch.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201202050456.164005-4-srikar@linux.vnet.ibm.com
We want to reuse the is_kvm_guest() name in a subsequent patch but
with a new body. Hence rename is_kvm_guest() to check_kvm_guest(). No
additional changes.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: kernel test robot <lkp@intel.com> # int -> bool fix
[mpe: Fold in fix from lkp to use true/false not 0/1]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201202050456.164005-3-srikar@linux.vnet.ibm.com
Only code/declaration movement, in anticipation of doing a KVM-aware
vcpu_is_preempted(). No additional changes.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201202050456.164005-2-srikar@linux.vnet.ibm.com
The power_pmu_event_init() callback access per-cpu variable
(cpu_hw_events) to check for event constraints and Branch Stack
(BHRB). Current usage is to disable preemption when accessing the
per-cpu variable, but this does not prevent timer callback from
interrupting event_init. Fix this by using 'local_irq_save/restore'
to make sure the code path is invoked with disabled interrupts.
This change is tested in mambo simulator to ensure that, if a timer
interrupt comes in during the per-cpu access in event_init, it will be
soft masked and replayed later. For testing purpose, introduced a
udelay() in power_pmu_event_init() to make sure a timer interrupt arrives
while in per-cpu variable access code between local_irq_save/resore.
As expected the timer interrupt was replayed later during local_irq_restore
called from power_pmu_event_init. This was confirmed by adding
breakpoint in mambo and checking the backtrace when timer_interrupt
was hit.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606814880-1720-1-git-send-email-atrajeev@linux.vnet.ibm.com
In a bunch of our security flushes, we use a comma rather than
a semicolon to 'terminate' an assignment. Nothing breaks, but
checkpatch picks it up if you copy it into another flush.
Switch to semicolons for ending statements.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201201144344.1228421-1-dja@axtens.net
Christophe Leroy
Christophe Lombard
Athira Rajeev
Aneesh Kumar K.V
Nicholas Piggin
Uwe Kleine-König
Srikar Dronamraju
Daniel Axtens
Frederic Barrat