The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200.
- Oneshot mode (used for NO_HZ and high res timers) uses the
alarm to emulate a real oneshot timer; the trickiest bit is
how to avoid some lowlevel races. Thanks to Remy Bohmer for
various fixes to this code.
- Tighten up periodic mode support using the PIT.
- Streamline reads of the 32KHz counter. Thanks to Marc Pignat
for some testing results: the CRTR register has *very* odd
behavior. The reread appears to work around stranger glitches
than just getting an old clock value (which would quickly
self-correct).
- Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100),
since that no longer acts correct (time increases too fast).
Note that the at91sam9 and at91x40 chips need other solutions,
since they don't have the same system timer module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by:Remy Bohmer <linux@bohmer.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Configuration support for the AT91x40 CPU and EB01 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Makefile build support for the Atmel AT91x40 CPU and EB01 board support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Atmel EB01 board (based on the Atmel AT91x40 CPU).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prototypes for the at91x40 CPU support functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Interrupt setup support for the Atmel AT91x40 CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the timers in the Atmel AT91x40 family of CPUs.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the AT91RM9200 platform-setup code to use the new atmel_spi
driver (and manually-driven chip-selects), instead of the legacy
AT91-only SPI stack.
The AT91SAM9 processors are already using the atmel_spi driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update csb337 board specific init to support "new style" rtc-ds1307 code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register the GPIO-connected buttons on the SAM9261-EK board as a
"gpio-keys" platform device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board-specific setup for the LCD on the Atmel AT91SAM9261-EK and
AT91SAM9263-EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 52ade9b3b9 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues. Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.
at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices. However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose. Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.
This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls. It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending to slow-clock mode, at91_pm_verify_clocks() is called to
ensure that all the clocks are disabled or in the correct state.
This patch replaces the "#warning TODO" messages for the SAM9 processors
with the correct code.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The number of programmable clocks available on the AT91 processors can
differ, therefore do not always display the contents of the PMC_PCKR(0)
.. PMC_PCKR(3) registers (ie, assume there are 4 clocks).
If CONFIG_AT91_PROGRAMMABLE_CLOCKS is enabled, the programmable clocks
will be registered like the other system/peripheral clocks, and the
state of the programmable clocks will be displayed like with the other
clocks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9RL-EK development board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.
(Dependent on ARM patch #4370/2)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached you can find a patch needed to make the LEDS for 'CPU-Idle'
and 'Timer' work on the AT91SAM9261-EK board. The kernel configuration
options are already there, but the implementation is not available.
Signed-off-by: Remy Bohmer <l.pinguin@gmail.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK
boards.
SAM9260-EK:
- Register I2C device.
SAM9263-EK:
- Add platform_data and register MACB device.
(Patch by Nicolas Ferre)
- Add platform_data and register AC97 device.
(Patch by Nicolas Ferre)
- Register I2C device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9263-EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9261-EK board.
Original patch by Morten Larsen.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define and register the remaining peripheral clocks for the AT91
processors.
AT91SAM9261 clocks patch by Ivan Zhakov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton found a section mismatch warning in x86_64 triggered by a
wrongly placed __initdata marker.
git grep "struct __initdata" revealed that board-sam9260.c had the same
problem.
This patch fixes this by placing the __initdata marker correct. It was
checked with objdump that the variable was moved to .init.data by this
change.
Fixed an unrelated section mismatch warning while touching the file.
Both changes are only compile tested but obvious correct.
[Used at91sam9260ek_defconfig to get compile coverage]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the picotux 200 ARM board:
- Enable its machine type in the filter in head.S
- Add configuration option
- Add board initialisation
- Add default configuration
Signed-off-by: Simon Richter <Simon.Richter@kleinhenz.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new gpio_direction_input() and gpio_direction_output() functions
were both enabling output mode. When configuring a GPIO for input mode,
you need to program the ODR (Output Disable Register).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.
Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
- Remove a duplicated define for AT91_RSTC_KEY
- Set AT91_RSTC_KEY to the correct value
- Replace the hardcoded keys in at91sam9620.c and at91sam9261.c
by AT91_RSTC_KEY
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9XE range of processors. These are
basically AT91SAM9260's with different amounts of internal SRAM and
Flash.
We make use of the existing AT91SAM9260 support, but just perform
run-time detection of the size of the internal SRAM.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MACB Ethernet driver searches for a "macb_clk" clock, so rename the
"ether_clk" on the SAM9260 and SAM9263 to "macb_clk".
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unconditionally disabling the PCKs (Programmable Clocks) is not a good
idea as it breaks boards that depend on those clocks being enabled by
bootloaders.
Therefore only disable unused clocks late in the init process, giving
the board init code the chance to claim the clock.
Patch from Steven Scholz.
Since the HCK clocks on SAM9261 are already being registered as a
independent clocks, we don't need the special case for HCK0 on the
SAM9261. Platform-init code and drivers should use the clock API to
enable/disable the clock.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO pin setup should be handed by the platform-setup code, and not
directly by the driver.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an overrun in the AT91SAM9 gettimeoffset() function. This causes
the time value returned by gettimeofday() to jump "backwards".
Original patch from Michel Benoit.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the physically mapped flash on the Cogent CSB337 and CSB637
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the Timer/Counter Unit clocks on the AT91RM9200, AT91SAM9260 and
AT91SAM9261 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263-EK board.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263 processor. It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rafael J. Wysocki
David Brownell
Greg Ungerer
Jan Altenberg
Andrew Victor
Russell King
Simon Arlott
Matt LaPlante
Bernhard Walle
Linus Torvalds
Johannes Berg
Sam Ravnborg
Simon Richter
Jan Altenberg