Copy the FPU state to the task's thread_info->fpregs for the VIS emulation
functions to access.
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix boot crash with numcpus=0 on certain systems
Fix early exception in __get_smp_config with nosmp.
Bail out early when there is no MP table.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes CONFIG_PCI_LEGACY (which is not needed) and consequently
several compiler warnings.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
KVM host support was recently enabled in ppc44x_defconfig, but since then the
config option was renamed. Update ppc44x_defconfig to match.
Also, KVM guests aren't very interesting without networking, so enable
CONFIG_TUN and CONFIG_BRIDGE.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Commit 0c65f459ce intended to fix truncation issues with fls() on
ARMv5+ by renaming it to __fls() and wrapping it into a C function.
However that didn't take into account the fact that __fls() already
already had different semantics in the kernel.
Let's move the __fls() code into fls() function directly, and redefine
__fls() with the appropriate semantics. While at it, bring a generic
__fls() definition for pre ARMv5 too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes some bugs in VIS emulation that cause the GCC test
failure
FAIL: gcc.target/sparc/pdist-3.c execution test
for both 32-bit and 64-bit testing on hardware lacking these
instructions. The emulation code for the pdist instruction uses
RS1(insn) for both source registers rs1 and rs2, which is obviously
wrong and leads to the instruction doing nothing (the observed
problem), and further inspection of the code shows that RS1 uses a
shift of 24 and RD a shift of 25, which clearly cannot both be right;
examining SPARC documentation indicates the correct shift for RS1 is
14.
This patch fixes the bug if single-stepping over the affected
instruction in the debugger, but not if the testcase is run
standalone. For that, Wind River has another patch I hope they will
send as a followup to this patch submission.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce into the MN10300 gdbstub 16550 driver a couple of barrier() calls to
replace the removed volatility of the input/output index variables for the Rx
ring buffer. A previous patch added them into the on-chip serial port driver.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bitops_64.h includes the generic one; pretty sure 32 should too.
(Found by using __fls in generic code and breaking sparc defconfig build:
thanks Stephen and linux-next!)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates the dts files for each core and splits the devices
between the two cores for MPC8572DS.
core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1.
core1 has L2, dma2, eth2, eth3, pci2, msi.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The flag MPIC_WANTS_RESET shouldn't be set if we are doing cooperative
asymmetric MP. The second linux shouldn't reset the pic or the first
one gets very confused.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add NOR and NAND flash partitions for mpc8572ds board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic support for the GPIO available on the SBC610 VPX Single Board Computer
from GE Fanuc (PowerPC MPC8641D).
This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO
functionality is exposed through the AFIX pins on the backplane, unless used
by an AFIX card.
This code currently does not support switching between totem-pole and
open-drain outputs (when used as outputs, GPIOs default to totem-pole).
The interrupt capabilites of the GPIO lines is also not currently supported.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch we can compile the qe_lib/usb.c without the UCC
support (that is, without UCC_GETH and/or SERIAL_QE).
Fixes following link error (CONFIG_SMP should be =y to trigger this):
arch/powerpc/sysdev/built-in.o: In function `qe_usb_clock_set':
(.text+0x3cae): undefined reference to `cmxgcr_lock'
make: *** [.tmp_vmlinux1] Error 1
While at it, also add missing spinlock.h includes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_mds.c: In function 'board_fixups':
arch/powerpc/platforms/85xx/mpc85xx_mds.c:244: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
arch/powerpc/platforms/85xx/mpc85xx_mds.c:250: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Alan Jenkins wrote:
> This is on an EeePC 701, /proc/cpuinfo as attached.
>
> Is this expected? Will the next release work?
>
> Thanks, Alan
>
> # opcontrol --setup --no-vmlinux
> cpu_type 'unset' is not valid
> you should upgrade oprofile or force the use of timer mode
>
> # opcontrol -v
> opcontrol: oprofile 0.9.4 compiled on Nov 29 2008 22:44:10
>
> # cat /dev/oprofile/cpu_type
> i386/p6
> # uname -r
> 2.6.28-rc6eeepc
Hi Alan,
Looking at the kernel driver code for oprofile it can return the "i386/p6" for
the cpu_type. However, looking at the user-space oprofile code there isn't the
matching entry in libop/op_cpu_type.c or the events/unit_mask files in
events/i386 directory.
The Intel AP-485 says this is a "Intel Pentium M processor model D". Seems like
the oprofile kernel driver should be identifying the processor as "i386/p6_mobile"
The driver identification code doesn't look quite right in nmi_init.c
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=blob;f=arch/x86/oprofile/nmi_int.c;h=022cd41ea9b4106e5884277096e80e9088a7c7a9;hb=HEAD
has:
409 case 10 ... 13:
410 *cpu_type = "i386/p6";
411 break;
Referring to the Intel AP-485:
case 10 and 11 should produce "i386/piii"
case 13 should produce "i386/p6_mobile"
I didn't see anything for case 12.
Something like the attached patch. I don't have a celeron machine to verify that
changes in this area of the kernel fix thing.
-Will
Signed-off-by: William Cohen <wcohen@redhat.com>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If oprofile statically compiled in kernel, a cpu unplug triggers
a panic in ppro_stop(), because a NULL pointer is dereferenced.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Added 85xx specifc smp_ops structure. We use ePAPR style boot release
and the MPIC for IPIs at this point.
Additionally added routines for secondary cpu entry and initializtion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The initial TLB mapping for the kernel boot didn't set the memory coherent
attribute, MAS2[M], in SMP mode.
If this code supported booting a secondary processor, which it doesn't yet,
but if it did, then when a secondary processor boots, it would probably signal
the primary processor by setting a variable called something like
__secondary_hold_acknowledge. However, due to the lack of the M bit, the
primary processor would not snoop the transaction (even if a transaction were
broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed
and the CPU would never see the ack. Which would have resulted in the primary
CPU spinning for a long time, perhaps a full second before it gives up, while
it would have waited for the ack from the secondary CPU that it wouldn't have
been able to see because of the stale cache.
The value of MAS2 for the boot page TLB1 entry is a compile time constant,
so there is no need to calculate it in powerpc assembly language.
Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent
offsets within a page are ignored and should be cleared." Existing code
didn't clear them, this code does.
The same when the page of KERNELBASE is found; we don't need to use asm to
mask the lower 12 bits off.
In the code that computes the address to rfi from, don't hard code the
offset to 24 bytes, but have the assembler figure that out for us.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch add the handlers of SPE/EFP exceptions.
The code is used to emulate float point arithmetic,
when MSR(SPE) is enabled and receive EFP data interrupt or EFP round interrupt.
This patch has no conflict with or dependence on FP math-emu.
The code has been tested by TestFloat.
Now the code doesn't support SPE/EFP instructions emulation
(it won't be called when receive program interrupt),
but it could be easily added.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FP_DECL_EX is already used, so ret is redundant.
And FP_SET_EXCEPTION will add status into return value.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using the same macro definition for _FP_CHOOSENAN as s390,
sh, sparc32/64. The original author didn't understand this and
matched what sparc64 was doing and they have updated to this definition.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PowerPC float point division emulation is derived from gcc.
I reported this problem on gcc maillist and got this reply:
http://gcc.gnu.org/ml/gcc/2008-03/msg00543.html
Since UDIV_NEEDS_NORMALIZATION is not used by kernel, we should use
_FP_DIV_MEAT_1_udiv_norm to make sure the single float point
is normalized before udiv_qrnnd.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After testing of various compiler flag combinations by Nate Case it was
determined that -mabi=no-spe has no impact on the compiler generating
SPE instructions. Only -mno-spe and -mspe=no do.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The access to the iommu->need_sync member needs to be protected by the
iommu->lock. Otherwise this is a possible race condition. Fix it with
this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In some rare cases a request can arrive an IOMMU with its originial
requestor id even it is aliased. Handle this by setting the device table
entry to the same protection domain for the original and the aliased
requestor id.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove 16 bytes of padding from struct amd_iommu on 64bit builds
reducing its size to 120 bytes, allowing it to span one fewer
cachelines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The name of the device_node field differ across the platforms, so we
have to implement inlined accessors. This is needed to avoid ugly
#ifdef in the generic code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ibmebus_free_irq() frees the IRQ but does not remove its mapping, which
results in stale entries in the map.
This fixes it by adding a call to irq_dispose_mapping() in
ibmebus_free_irq().
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As noted by Akinobu Mita in commit b1fceac2 ("x86: remove unnecessary
memset and NULL check after alloc_bootmem()"), alloc_bootmem and
related functions never return NULL and always return a zeroed region
of memory. Thus a NULL test or memset after calls to these functions
is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to swap these out once we start using swiotlb, so add
them to dma_ops. Create CONFIG_PPC_NEED_DMA_SYNC_OPS Kconfig
option; this is currently enabled automatically if we're
CONFIG_NOT_COHERENT_CACHE. In the future, this will also
be enabled for builds that need swiotlb. If PPC_NEED_DMA_SYNC_OPS
is not defined, the dma_sync_*_for_* ops compile to nothing.
Otherwise, they access the dma_ops pointers for the sync ops.
This patch also changes dma_sync_single_range_* to actually
sync the range - previously it was using a generous
dma_sync_single. dma_sync_single_* is now implemented
as a dma_sync_single_range with an offset of 0.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On my screen, when something crashes, I only have space for maybe 16
functions of the stack trace before the information above it scrolls
off the screen. It's easy to hack the kernel to print out only that
much, but it's harder to remember to do it. This introduces a config
option for it so that I can keep the setting in my config.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor the RCU based pte free code that was used on ppc64 to be used
on all powerpc.
Additionally refactor pte_free() & pte_free_kernel() into common code
between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The tlb invalidates in kmap_atomic/kunmap_atomic can be called from
IRQ context, however they are only local invalidates (on the processor
that the kmap was called on). In the future we want to use IPIs to
do tlb invalidates this causes issue since flush_tlb_page() is considered
a broadcast invalidate.
Add local_flush_tlb_page() as a non-broadcast invalidate and use it in
kmap_atomic() since we don't have enough information in the
flush_tlb_page() call to determine its local.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the ifdefs so we only use hash_page_sync if we have
CONFIG_SMP && CONFIG_PPC_STD_MMU_32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit hash code didn't need it so far so we don't update
mm->cpu_vm_mask on context switch. This however will break when we
merge the RCU based page table freeing patch and other upcoming 32-bit
embedded SMP work, so this adds the update.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: remove stale IOTLB entries
In the non-default nofullflush case the GART is only flushed when
next_bit wraps around. But it can happen that an unmap operation unmaps
memory which is behind the current next_bit location. If these addresses
are reused it may result in stale GART IO/TLB entries. Fix this by
setting the GART next_bit always behind an unmapped location.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From: Chris Torek <chris.torek@windriver.com>
>The SPARC64 kernel code for PTRACE_SETFPREGS64 appears to be an exact copy
>of that for PTRACE_GETFPREGS64. This means that gdbserver and native
>64-bit GDB cannot set floating-point registers.
It looks like a simple typo.
Signed-off-by: David S. Miller <davem@davemloft.net>
On PowerPC 4xx or other non cache-coherent platforms, we lost the
appropriate cache flushing in dma_map_sg() when merging the 32 and
64-bit DMA code (commit 4fc665b88a,
"powerpc: Merge 32 and 64-bit dma code"). This restores it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: avoid creation of unreachable pages in the shadow
KVM: ppc: stop leaking host memory on VM exit
KVM: MMU: fix sync of ptes addressed at owner pagetable
KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
KVM: ia64: Fix incorrect kbuild CFLAGS override
KVM: VMX: Fix interrupt loss during race with NMI
KVM: s390: Fix problem state handling in guest sigp handler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.28-rc7
macfb: Do not overflow fb_fix_screeninfo.id
This fixes the MN10300 kernel module linking to match the toolchain. RELA
relocs don't use the value at the location being relocated. This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id. We were writing that directly
into the HW register.
We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the error handling in sys_mmap2(). Currently, if the pgoff check
fails, fput() might have to be called (which it isn't), so do the pgoff
check first, before fget() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of sillies, from missing 'const' to using
'return' in void functions, to functions with no arguments not even
'void' and a cast which isn't required.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: do not expose a control that has no effect
Fix to prevent sched_mc_power_saving from being exported through sysfs
on single-socket systems. (Say multicore single socket (Laptop))
CPU core map of the boot cpu should be equal to possible number
of cpus for single socket system.
This fix has been developed at FOSS.in kernel workout.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the
attribute removal with the same condition. This fixes this build error
on 32-bit SMP configurations:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function)
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING
= y, if a program sets the SO (summary overflow) bit in the XER and
then does a system call, the SO bit in CR0 will be set on return
regardless of whether the system call detected an error. Since CR0.SO
is used as the error indication from the system call, this means that
all system calls appear to fail.
The reason is that the workaround for the timebase bug on Cell uses a
compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the
ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a
compare instruction, which copies XER.SO to CR0.SO. Since we were
doing this in the system call entry patch after clearing CR0.SO but
before saving the CR, this meant that the saved CR image had CR0.SO
set if XER.SO was set on entry.
This fixes it by moving the clearing of CR0.SO to after the
ACCOUNT_CPU_USER_ENTRY call in the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An earlier patch from Jens Osterkamp attempted to fix GDB
watchpoints by enabling the DABRX register at boot time.
Unfortunately, this did not work on SMP setups, where
secondary CPUs were still using the power-on DABRX value.
This introduces the same change for secondary CPUs on cell
as well.
Reported-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Tested-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MSI capture logic for the axon bridge can sometimes
lose interrupts in case of high DMA and interrupt load,
when it signals an MSI interrupt to the MPIC interrupt
controller while we are already handling another MSI.
Each MSI vector gets written into a FIFO buffer in main
memory using DMA, and that DMA access is normally flushed
by the actual interrupt packet on the IOIF. An MMIO
register in the MSIC holds the position of the last
entry in the FIFO buffer that was written. However,
reading that position does not flush the DMA, so that
we can observe stale data in the buffer.
In a stress test, we have observed the DMA to arrive
up to 14 microseconds after reading the register.
This patch works around this problem by retrying the
access to the FIFO buffer.
We can reliably detect the conditioning by writing
an invalid MSI vector into the FIFO buffer after
reading from it, assuming that all MSIs we get
are valid. After detecting an invalid MSI vector,
we udelay(1) in the interrupt cascade for up to
100 times before giving up.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I got a bug report about a distro kernel not booting on a particular
machine. It would freeze during boot:
> ...
> Could not find start_pfn for node 1
> [boot]0015 Setup Done
> Built 2 zonelists in Node order, mobility grouping on. Total pages: 123783
> Policy zone: DMA
> Kernel command line:
> [boot]0020 XICS Init
> [boot]0021 XICS Done
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> clocksource: timebase mult[7d0000] shift[22] registered
> Console: colour dummy device 80x25
> console handover: boot [udbg0] -> real [hvc0]
> Dentry cache hash table entries: 1048576 (order: 7, 8388608 bytes)
> Inode-cache hash table entries: 524288 (order: 6, 4194304 bytes)
> freeing bootmem node 0
I've reproduced this on 2.6.27.7. It is caused by commit
8f64e1f2d1 ("powerpc: Reserve in bootmem
lmb reserved regions that cross NUMA nodes").
The problem is that Jon took a loop which was (in pseudocode):
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
reserve_node_bootmem(nid);
and broke it up into:
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
for_each_node(nid)
reserve_node_bootmem(nid);
The issue comes in when the 'careful_alloc()' is called on a node with
no memory. It falls back to using bootmem from a previously-initialized
node. But, bootmem has not yet been reserved when Jon's patch is
applied. It gives back bogus memory (0xc000000000000000) and pukes
later in boot.
The following patch collapses the loop back together. It also breaks
the mark_reserved_regions_for_nid() code out into a function and adds
some comments. I think a huge part of introducing this bug is because
for loop was too long and hard to read.
The actual bug fix here is the:
+ if (end_pfn <= node->node_start_pfn ||
+ start_pfn >= node_end_pfn)
+ continue;
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, some PCIe devices on POWER6 machines do not get interrupts
assigned correctly. The problem is that OF doesn't create an
"interrupt" property for them. The fix is for of_irq_map_pci to fall
back to using the value in the PCI interrupt-pin register in config
space, as we do when there is no OF device-tree node for the device.
I have verified that this works fine with a pair of Squib-E SAS
adapter on a P6-570.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: struct device - replace bus_id with dev_name(), dev_set_name()
parisc: fix kernel crash when unwinding a userspace process
parisc: __kernel_time_t is always long
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq.h: fix missing/extra kernel-doc
genirq: __irq_set_trigger: change pr_warning to pr_debug
irq: fix typo
x86: apic honour irq affinity which was set in early boot
genirq: fix the affinity setting in setup_irq
genirq: keep affinities set from userspace across free/request_irq()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: always define DECLARE_PCI_UNMAP* macros
x86: fixup config space size of CPU functions for AMD family 11h
x86, bts: fix wrmsr and spinlock over kmalloc
x86, pebs: fix PEBS record size configuration
x86, bts: turn macro into static inline function
x86, bts: exclude ds.c from build when disabled
arch/x86/kernel/pci-calgary_64.c: change simple_strtol to simple_strtoul
x86: use limited register constraint for setnz
xen: pin correct PGD on suspend
x86: revert irq number limitation
x86: fixing __cpuinit/__init tangle, xsave_cntxt_init()
x86: fix __cpuinit/__init tangle in init_thread_xstate()
oprofile: fix an overflow in ppro code
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: ignore out-of-range PstateStatus value
[CPUFREQ] Documentation: Add Blackfin to list of supported processors
Compress a set of consecutive switch cases into a case-range.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... so get xen-ops.h in agreement with xen/smp.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual "introduce .text.head, put it in front of TEXT_TEXT in vmlinux.lds.S,
make the stuff up to jump to start_kernel live in it", same as on other
targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All noise since we don't have CPU hotplug there. However, they
did expose something very odd-looking in there - poke_viking()
does a bunch of identical btfixup each time it's called (i.e.
for each CPU). That one is left alone for now; just the trivial
misannotation fixes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
called only from __init, calls __init. Incidentally, it ought to be static
in file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pure noise - alpha doesn't have CPU hotplug
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Devices like b44 ethernet can't dma from addresses above 1GB. The driver
handles this cases by falling back to GFP_DMA allocation. But for detecting
the problem it needs to get an indication from dma_mapping_error.
The bug is triggered by using a VMSPLIT option of 2G/2G.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot crash on AMD IOMMU if CONFIG_GART_IOMMU is off
Currently these macros evaluate to a no-op except the kernel is compiled
with GART or Calgary support. But we also need these macros when we have
SWIOTLB, VT-d or AMD IOMMU in the kernel. Since we always compile at
least with SWIOTLB we can define these macros always.
This patch is also for stable backport for the same reason the SWIOTLB
default selection patch is.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need an alignment of 16384 bytes for the initial kernel stack if
the kernel is configured for 16384 bytes stacks but the linker script
currently guarantees only an alignment of 8192 bytes.
So fix this and simply use THREAD_SIZE as alignment value which will
always do the right thing.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When running several kvm processes with lots of memory overcommitment,
we have seen an oops during process shutdown:
------------[ cut here ]------------
Kernel BUG at 0000000000193434 [verbose debug info unavailable]
addressing exception: 0005 [#1] PREEMPT SMP
Modules linked in: kvm sunrpc qeth_l2 dm_mod qeth ccwgroup
CPU: 10 Not tainted 2.6.28-rc4-kvm-bigiron-00521-g0ccca08-dirty #8
Process kuli (pid: 14460, task: 0000000149822338, ksp: 0000000024f57650)
Krnl PSW : 0704e00180000000 0000000000193434 (unmap_vmas+0x884/0xf10)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 EA:3
Krnl GPRS: 0000000000000002 0000000000000000 000000051008d000 000003e05e6034e0
00000000001933f6 00000000000001e9 0000000407259e0a 00000002be88c400
00000200001c1000 0000000407259608 0000000407259e08 0000000024f577f0
0000000407259e09 0000000000445fa8 00000000001933f6 0000000024f577f0
Krnl Code: 0000000000193426: eb22000c000d sllg %r2,%r2,12
000000000019342c: a7180000 lhi %r1,0
0000000000193430: b2290012 iske %r1,%r2
>0000000000193434: a7110002 tmll %r1,2
0000000000193438: a7840006 brc 8,193444
000000000019343c: 9602c000 oi 0(%r12),2
0000000000193440: 96806000 oi 0(%r6),128
0000000000193444: a7110004 tmll %r1,4
Call Trace:
([<00000000001933f6>] unmap_vmas+0x846/0xf10)
[<0000000000199680>] exit_mmap+0x210/0x458
[<000000000012a8f8>] mmput+0x54/0xfc
[<000000000012f714>] exit_mm+0x134/0x144
[<000000000013120c>] do_exit+0x240/0x878
[<00000000001318dc>] do_group_exit+0x98/0xc8
[<000000000013e6b0>] get_signal_to_deliver+0x30c/0x358
[<000000000010bee0>] do_signal+0xec/0x860
[<0000000000112e30>] sysc_sigpending+0xe/0x22
[<000002000013198a>] 0x2000013198a
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<00000000001a68d0>] free_swap_and_cache+0x1a0/0x1a4
<4>---[ end trace bc19f1d51ac9db7c ]---
The faulting instruction is the storage key operation (iske) in
ptep_rcp_copy (called by pte_clear, called by unmap_vmas). iske
reads dirty and reference bit information for a physical page and
requires a valid physical address. Since we are in pte_clear, we
cannot rely on the pte containing a valid address. Fortunately we
dont need these information in pte_clear - after all there is no
mapping. The best fix is to remove the needless call to ptep_rcp_copy
that contains the iske.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_PRINTK_TIME reveals that sched_clock has a wrong offset during boot:
..
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 775679
[ 0.000000] Kernel command line: dasd=4b6c root=/dev/dasda1 ro noinitrd
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[6920575.975232] console [ttyS0] enabled
[6920575.987586] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[6920575.991404] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
..
The s390 implementation of sched_clock uses the store clock instruction and
subtracts jiffies_timer_cc.
jiffies_timer_cc is a local variable in arch/s390/kernel/time.c and only used
for sched_clock and monotonic clock. For historical reasons there is an offset
on that value. With todays code this offset is unnecessary. By removing that
offset we can get a sched_clock which returns the nanoseconds after time_init.
This improves CONFIG_PRINTK_TIME.
Since sched_clock is the only user, I have also renamed jiffies_timer_cc to
sched_clock_base_cc. In addition, the local variable init_timer_cc is redundant
and can be romved as well.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
syscall_get_nr() currently returns a valid result only if the call
chain of the traced process includes do_syscall_trace_enter(). But
collect_syscall() can be called for any sleeping task, the result of
syscall_get_nr() in general is completely bogus.
To make syscall_get_nr() work for any sleeping task the traps field
in pt_regs is replace with svcnr - the system call number the process
is executing. If svcnr == 0 the process is not on a system call path.
The syscall_get_arguments and syscall_set_arguments use regs->gprs[2]
for the first system call parameter. This is incorrect since gprs[2]
may have been overwritten with the system call number if the call
chain includes do_syscall_trace_enter. Use regs->orig_gprs2 instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the correct wake-up enable register, and make it
work with 34xx also.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
(I did not compile or test it, please let me know, or help fixing
it, if something is wrong with the conversion)
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: linux-parisc@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Any user on existing parisc 32- and 64bit-kernels can easily crash
the kernel and as such enforce a DSO.
A simple testcase is available here:
http://gsyprf10.external.hp.com/~deller/crash.tgz
The problem is introduced by the fact, that the handle_interruption()
crash handler calls the show_regs() function, which in turn tries to
unwind the stack by calling parisc_show_stack(). Since the stack contains
userspace addresses, a try to unwind the stack is dangerous and useless
and leads to the crash.
The fix is trivial: For userspace processes
a) avoid to unwind the stack, and
b) avoid to resolve userspace addresses to kernel symbol names.
While touching this code, I converted print_symbol() to %pS
printk formats and made parisc_show_stack() static.
An initial patch for this was written by Kyle McMartin back in August:
http://marc.info/?l=linux-parisc&m=121805168830283&w=2
Compile and run-tested with a 64bit parisc kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, earlier...]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
__kernel_time_t is always long on PA-RISC, irrespective of CONFIG_64BIT,
hence move it out of the #ifdef CONFIG_64BIT / #else / #endif block.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
It is possible for a shadow page to have a parent link
pointing to a freed page. When zapping a high level table,
kvm_mmu_page_unlink_children fails to remove the parent_pte link.
For that to happen, the child must be unreachable via the shadow
tree, which can happen in shadow_walk_entry if the guest pte was
modified in between walk() and fetch(). Remove the parent pte
reference in such case.
Possible cause for oops in bug #2217430.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
0 is a valid GPIO number, use a negative number to specify, that this camera
doesn't have a GPIO for bus-width switching.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Impact: extend allowed configuration space access on 11h CPUs from 256 to 4K
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The second clk_deny_idle instance should be clk_allow_idle instead.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A workaround for AMD CPU family 11h erratum 311 might cause that the
P-state Status Register shows a "current P-state" which is larger than
the "current P-state limit" in P-state Current Limit Register. For the
wrong P-state value there is no ACPI _PSS object defined and
powernow-k8/cpufreq can't determine the proper CPU frequency for that
state.
As a consequence this can cause a panic during boot (potentially with
all recent kernel versions -- at least I have reproduced it with
various 2.6.27 kernels and with the current .28 series), as an
example:
powernow-k8: Found 1 AMD Turion(tm)X2 Ultra DualCore Mobile ZM-82 processors (2 \
)
powernow-k8: 0 : pstate 0 (2200 MHz)
powernow-k8: 1 : pstate 1 (1100 MHz)
powernow-k8: 2 : pstate 2 (600 MHz)
BUG: unable to handle kernel paging request at ffff88086e7528b8
IP: [<ffffffff80486361>] cpufreq_stats_update+0x4a/0x5f
PGD 202063 PUD 0
Oops: 0002 [#1] SMP
last sysfs file:
CPU 1
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.28-rc3-dirty #16
RIP: 0010:[<ffffffff80486361>] [<ffffffff80486361>] cpufreq_stats_update+0x4a/0\
f
Synaptics claims to have extended capabilities, but I'm not able to read them.<6\
6
RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffff88006e7528c0
RDX: 00000000ffffffff RSI: ffff88006e54af00 RDI: ffffffff808f056c
RBP: 00000000fffee697 R08: 0000000000000003 R09: ffff88006e73f080
R10: 0000000000000001 R11: 00000000002191c0 R12: ffff88006fb83c10
R13: 00000000ffffffff R14: 0000000000000001 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006fb50740(0000) knlGS:0000000000000000
Unable to initialize Synaptics hardware.
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffff88086e7528b8 CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff88006fb82000, task ffff88006fb816d0)
Stack:
ffff88006e74da50 0000000000000000 ffff88006e54af00 ffffffff804863c7
ffff88006e74da50 0000000000000000 00000000ffffffff 0000000000000000
ffff88006fb83c10 ffffffff8024b46c ffffffff808f0560 ffff88006fb83c10
Call Trace:
[<ffffffff804863c7>] ? cpufreq_stat_notifier_trans+0x51/0x83
[<ffffffff8024b46c>] ? notifier_call_chain+0x29/0x4c
[<ffffffff8024b561>] ? __srcu_notifier_call_chain+0x46/0x61
[<ffffffff8048496d>] ? cpufreq_notify_transition+0x93/0xa9
[<ffffffff8021ab8d>] ? powernowk8_target+0x1e8/0x5f3
[<ffffffff80486687>] ? cpufreq_governor_performance+0x1b/0x20
[<ffffffff80484886>] ? __cpufreq_governor+0x71/0xa8
[<ffffffff80484b21>] ? __cpufreq_set_policy+0x101/0x13e
[<ffffffff80485bcd>] ? cpufreq_add_dev+0x3f0/0x4cd
[<ffffffff8048577a>] ? handle_update+0x0/0x8
[<ffffffff803c2062>] ? sysdev_driver_register+0xb6/0x10d
[<ffffffff8056592c>] ? powernowk8_init+0x0/0x7e
[<ffffffff8048604c>] ? cpufreq_register_driver+0x8f/0x140
[<ffffffff80209056>] ? _stext+0x56/0x14f
[<ffffffff802c2234>] ? proc_register+0x122/0x17d
[<ffffffff802c23a0>] ? create_proc_entry+0x73/0x8a
[<ffffffff8025c259>] ? register_irq_proc+0x92/0xaa
[<ffffffff8025c2c8>] ? init_irq_proc+0x57/0x69
[<ffffffff807fc85f>] ? kernel_init+0x116/0x169
[<ffffffff8020cc79>] ? child_rip+0xa/0x11
[<ffffffff807fc749>] ? kernel_init+0x0/0x169
[<ffffffff8020cc6f>] ? child_rip+0x0/0x11
Code: 05 c5 83 36 00 48 c7 c2 48 5d 86 80 48 8b 04 d8 48 8b 40 08 48 8b 34 02 48\
RIP [<ffffffff80486361>] cpufreq_stats_update+0x4a/0x5f
RSP <ffff88006fb83b20>
CR2: ffff88086e7528b8
---[ end trace 0678bac75e67a2f7 ]---
Kernel panic - not syncing: Attempted to kill init!
In short, aftereffect of the wrong P-state is that
cpufreq_stats_update() uses "-1" as index for some array in
cpufreq_stats_update (unsigned int cpu)
{
...
if (stat->time_in_state)
stat->time_in_state[stat->last_index] =
cputime64_add(stat->time_in_state[stat->last_index],
cputime_sub(cur_time, stat->last_time));
...
}
Fortunately, the wrong P-state value is returned only if the core is
in P-state 0. This fix solves the problem by detecting the
out-of-range P-state, ignoring it, and using "0" instead.
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: fix sleeping-with-spinlock-held bugs/crashes
- Turn a wrmsr to write the DS_AREA MSR into a wrmsrl.
- Use irqsave variants of spinlocks.
- Do not allocate memory while holding spinlocks.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix DS hw enablement on 64-bit x86
Fix the PEBS record size in the DS configuration.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Replace a macro with a static inline function.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Move the CONFIG guard from the .c file into the makefile.
Reported-by: Andi Kleen <andi-suse@firstfloor.org>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix theoretical option string parsing overflow
Since bridge is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: muli@il.ibm.com
Cc: jdmason@kudzu.us
Cc: discuss@x86-64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix with certain compilers
GCC can decide to use %dil when "r" is used, which is not valid for
setnz.
This bug was brought out by Stephen Rothwell's merging of the
branch tracer into linux-next.
[ Thanks to Uros Bizjak for recommending 'q' over 'Q' ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the VM exits, we must call put_page() for every page referenced in the
shadow TLB.
Without this patch, we usually leak 30-50 host pages (120 - 200 KiB with 4 KiB
pages). The maximum number of pages leaked is the size of our shadow TLB, 64
pages.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Often we do things like put BUG() in the default clause of a case
statement. Since it was not declared __noreturn, this could sometimes
lead to bogus compiler warnings that variables were used
uninitialized.
There is a small problem in that we have to put a magic while(1); loop to
fool GCC into really thinking it is noreturn. This makes the new
BUG() function 3 instructions long instead of just 1, but I think it
is worth it as it is now unnecessary to do extra work to silence the
'used uninitialized' warnings.
I also re-wrote BUG_ON so that if it is given a constant condition, it
just does BUG() instead of loading a constant value in to a register
and testing it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During page sync, if a pagetable contains a self referencing pte (that
points to the pagetable), the corresponding spte may be marked as
writable even though all mappings are supposed to be write protected.
Fix by clearing page unsync before syncing individual sptes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
PAL_VPS_RESUME_HANDLER should use r26 to hold vac fields according to SDM.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use CFLAGS_vcpu.o, not EXTRA_CFLAGS, to provide fixed register information
to the compiler.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If an interrupt cannot be injected for some reason (say, page fault
when fetching the IDT descriptor), the interrupt is marked for
reinjection. However, if an NMI is queued at this time, the NMI
will be injected instead and the NMI will be lost.
Fix by deferring the NMI injection until the interrupt has been
injected successfully.
Analyzed by Jan Kiszka.
Signed-off-by: Avi Kivity <avi@redhat.com>
We can get an exit for instructions starting with 0xae, even if the guest is
in userspace. Lets make sure, that the signal processor handler is only called
in guest supervisor mode. Otherwise, send a program check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: fix MSIx not enough irq numbers available regression
The manual revert of the sparse_irq patches missed to bring the number
of possible irqs back to the .27 status. This resulted in a regression
when two multichannel network cards were placed in a system with only
one IO_APIC - causing the networking driver to not have the right
IRQ and the device not coming up.
Remove the dynamic allocation logic leftovers and simply return
NR_IRQS in probe_nr_irqs() for now.
Fixes: http://lkml.org/lkml/2008/11/19/354
Reported-by: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jesper Dangaard Brouer <hawk@diku.dk>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
Currently, we can end up in an infinite loop if we get a signal
while the kernel has faulted in spufs_ps_fault. Eg:
alarm(1);
write(fd, some_spu_psmap_register_address, 4);
- the write's copy_from_user will fault on the ps mapping, and
signal_pending will be non-zero. Because returning from the fault
handler will never clear TIF_SIGPENDING, so we'll just keep faulting,
resulting in an unkillable process using 100% of CPU.
This change returns VM_FAULT_SIGBUS if there's a fatal signal pending,
letting us escape the loop.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:
* Base kernel code ran in permissive mode where the only traps
generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
unaligned accesses caused traps to the 0x5a00 unaligned reference
vector.
Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Signed-off-by: Tony Luck <tony.luck@intel.com>
When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used. If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.
This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: csrc-r4k: Fix declaration depending on the wrong CONFIG_ symbol.
MIPS: csrc-r4k: Fix spelling mistake.
MIPS: RB532: Provide functions for gpio configuration
MIPS: IP22: Make indy_sc_ops variable static
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
MIPS: Malta: Fix include paths in malta-amon.c
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: uaccess_64: fix return value in __copy_from_user()
x86: quirk for reboot stalls on a Dell Optiplex 330
Commit 81e192d6ce ("parisc: convert to
generic compat_sys_ptrace") introduced a bug which segfaults the parisc
64bit kernel when stracing 32bit applications:
Kernel Fault: Code=15 regs=00000000bafa42b0 (Addr=00000001baf5ab57)
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001101111111100001011 Tainted: G W
r00-03 000000ff0806ff0b 000000004068edc0 00000000401203f8 00000000fb3e2508
r04-07 0000000040686dc0 00000000baf5a800 fffffffffffffffc fffffffffb3e2508
r08-11 00000000baf5a800 000000000004b068 00000000000402b0 0000000000040d68
r12-15 0000000000042a9c 0000000000040a9c 0000000000040d60 0000000000042e9c
r16-19 000000000004b060 000000000004b058 0000000000042d9c ffffffffffffffff
r20-23 000000000800000b 0000000000000000 000000000800000b fffffffffb3e2508
r24-27 00000000fffffffc 0000000000000003 00000000fffffffc 0000000040686dc0
r28-31 00000001baf5a7ff 00000000bafa4280 00000000bafa42b0 00000000000001d7
sr00-03 0000000000fca000 0000000000000000 0000000000000000 0000000000fca000
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 0000000040120400 0000000040120404
IIR: 4b9a06b0 ISR: 0000000000000000 IOR: 00000001baf5ab57
CPU: 0 CR30: 00000000bafa4000 CR31: 00000000d22344e0
ORIG_R28: 00000000fb3e2248
IAOQ[0]: compat_arch_ptrace+0xb8/0x160
IAOQ[1]: compat_arch_ptrace+0xbc/0x160
RP(r2): compat_arch_ptrace+0xb0/0x160
Backtrace:
[<00000000401612ac>] compat_sys_ptrace+0x15c/0x180
[<0000000040104ef8>] syscall_exit+0x0/0x14
The problem is that compat_arch_ptrace() enters with an addr value of
type compat_ulong_t and calls translate_usr_offset() to translate the
address offset into a struct pt_regs offset like this:
addr = translate_usr_offset(addr)
this means that any return value of translate_usr_offset() is stored
back as compat_ulong_t type into the addr variable.
But since translate_usr_offset() returns -1 for invalid offsets, addr
can now get the value 0xffffffff which then fails the next return-value
sanity check and thus the kernel tries to access invalid memory:
if (addr < 0)
break;
Fix this bug by modifying translate_usr_offset() to take and return
values of type compat_ulong_t, and by returning the value
"sizeof(struct pt_regs)" as an error indicator.
Additionally change the sanity check to check for return values
for >= sizeof(struct pt_regs).
This patch survived my compile and run-tests.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The indy_sc_ops variable in arch/mips/mm/sc-ip22.c is needlessly defined
global, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.
Also define the zero offset of the alternate function register to allow
consistent access.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hong H. Pham
Andi Kleen
Benjamin Herrenschmidt
Stephen Rothwell
Hollis Blanchard
Nicolas Pitre
Joseph Myers
David Howells
Rusty Russell
Haiying Wang
Ingo Molnar
Martyn Welch
Anton Vorontsov
Kumar Gala
William Cohen
Eric Dumazet
Trent Piepho
Liu Yu
Joerg Roedel
Richard Kennedy
Sebastien Dugue
Julia Lawall
Becky Bruce
Johannes Berg
Paul Mackerras
Chris Torek
Linus Torvalds
Mark Salter
Saeed Bishara
Geert Uytterhoeven
Ben Dooks
Russell King
David S. Miller
Mahesh Salgaonkar
Milton Miller
Arnd Bergmann
Dave Hansen
Adhemerval Zanella
Robert P. J. Day
Christoph Hellwig
Al Viro
Thomas Bogendoerfer
Marek Vasut
Martin Schwidefsky
Heiko Carstens
Christian Borntraeger
Tero Kristo
Kay Sievers
Helge Deller
Marcelo Tosatti
Eric Miao
Guennadi Liakhovetski
Andreas Herrmann
Amit Kucheria
Markus Metzger
Steven Rostedt
David Daney
Xiantao Zhang
Avi Kivity
Ian Campbell
Thomas Gleixner
Robert Jarzmik
Jeremy Kerr
Isaku Yamahata
Huang Weiyi
Hidetoshi Seto
Tony Luck
Matthew Wilcox
Ralf Baechle
Phil Sutter
Dmitri Vorobiev
Florian Fainelli