The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.
Fixes: bee9d41b37 ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.
Fixes: bee9d41b37 ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc driver can get repeated calls to netvsc_rx_mode during
network setup; each of these calls ends up scheduling the lower
layers to update tha packet filter. This update requires an
request/response to the host. So avoid doing this if we already
know that the correct packet filter value is set.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.
Fixes: 009f766ca2 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaoVCFAAoJEG4XJFUm622bRiQIAKJ9HmZQwda8Y7Ypj/y2YIJr
Rqmd+PSjfD+FNT33Ue+x/LPCfM2SnFQdnL61kqOSIgOCDS+uwwe8mDVa+DtaT+Dd
sU5ftjVjBXuYiqs2XW0n8dPszFftc7omCNVAeAJcBISqrqKkXUi3Bg47jK02kV6E
AAGvyJwxIMr187nFaC8N55cas0At7Mbbsvh0YRNjxnoqKOmC3NpJZPskv3C/gvUs
ADJkFPUwImqE9+BwoEguAGcqV8hLVVnoXf87Ro4L1SrFl11gJSiifq/FqwXHXm8E
YyJNo6lGdaw5uuX2T9wW6QfBghMoncE/tmwgLKdLyjyV8H2c6iEMKMygZIN0eTI=
=HvdQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo:
====================
wireless-drivers fixes for 4.16
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The __send_and_alloc_skb() receives a skb ptr as a parameter but in
case it fails the skb is not valid:
- Send failed and released the skb internally.
- Allocation failed.
The current code tries to release the skb in case of failure which
causes redundant freeing.
Fixes: 9b00cf2d10 ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:
Call trace:
phy_detach+0x94/0x150
phy_disconnect+0x40/0x50
smsc911x_stop+0x104/0x128 [smsc911x]
__dev_close_many+0xb4/0x138
dev_close_many+0xbc/0x190
rollback_registered_many+0x140/0x460
rollback_registered+0x68/0xb0
unregister_netdevice_queue+0x100/0x118
unregister_netdev+0x28/0x38
smsc911x_drv_remove+0x58/0x130 [smsc911x]
platform_drv_remove+0x30/0x50
device_release_driver_internal+0x15c/0x1f8
driver_detach+0x54/0x98
bus_remove_driver+0x64/0xe8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
SyS_delete_module+0x1e8/0x238
__sys_trace_return+0x0/0x4
This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()
To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.
Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).
An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.
The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.
In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-03-05
This series contains fixes to e1000e only.
Benjamin Poirier provides all but one fix in this series, starting with
workaround for a VMWare e1000e emulation issue where ICR reads 0x0 on
the emulated device. Partially reverted a previous commit dealing with
the "Other" interrupt throttling to avoid unforeseen fallout from these
changes that are not strictly necessary. Restored the ICS write for
receive and transmit queue interrupts in the case that txq or rxq bits
were set in ICR and the Other interrupt handler read and cleared ICR
before the queue interrupt was raised. Fixed an bug where interrupts
may be missed if ICR is read while INT_ASSERTED is not set, so avoid the
problem by setting all bits related to events that can trigger the Other
interrupt in IMS. Fixed the return value for check_for_link() when
auto-negotiation is off.
Pierre-Yves Kerbrat fixes e1000e to use dma_zalloc_coherent() to make
sure the ring is memset to 0 to prevent the area from containing
garbage.
v2: added an additional e1000e fix to the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The feature module needs to evaluate the actual firmware error return
upon a control command. This adds a flag to struct brcmf_if that the
caller can set. This flag is checked to determine the error code that
needs to be returned.
Fixes: b69c1df472 ("brcmfmac: separate firmware errors from i/o errors")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct spelling of National Semi-conductor (no hyphen)
in drivers/net/ethernet/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 820ee17b8d ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 2b2427d064 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: d2fa47d9dd ("phy: marvell: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)
This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.
Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Use an appropriate TSQ pacing shift in mac80211, from Toke
Høiland-Jørgensen.
2) Just like ipv4's ip_route_me_harder(), we have to use skb_to_full_sk
in ip6_route_me_harder, from Eric Dumazet.
3) Fix several shutdown races and similar other problems in l2tp, from
James Chapman.
4) Handle missing XDP flush properly in tuntap, for real this time.
From Jason Wang.
5) Out-of-bounds access in powerpc ebpf tailcalls, from Daniel
Borkmann.
6) Fix phy_resume() locking, from Andrew Lunn.
7) IFLA_MTU values are ignored on newlink for some tunnel types, fix
from Xin Long.
8) Revert F-RTO middle box workarounds, they only handle one dimension
of the problem. From Yuchung Cheng.
9) Fix socket refcounting in RDS, from Ka-Cheong Poon.
10) Don't allow ppp unit registration to an unregistered channel, from
Guillaume Nault.
11) Various hv_netvsc fixes from Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (98 commits)
hv_netvsc: propagate rx filters to VF
hv_netvsc: filter multicast/broadcast
hv_netvsc: defer queue selection to VF
hv_netvsc: use napi_schedule_irqoff
hv_netvsc: fix race in napi poll when rescheduling
hv_netvsc: cancel subchannel setup before halting device
hv_netvsc: fix error unwind handling if vmbus_open fails
hv_netvsc: only wake transmit queue if link is up
hv_netvsc: avoid retry on send during shutdown
virtio-net: re enable XDP_REDIRECT for mergeable buffer
ppp: prevent unregistered channels from connecting to PPP units
tc-testing: skbmod: fix match value of ethertype
mlxsw: spectrum_switchdev: Check success of FDB add operation
net: make skb_gso_*_seglen functions private
net: xfrm: use skb_gso_validate_network_len() to check gso sizes
net: sched: tbf: handle GSO_BY_FRAGS case in enqueue
net: rename skb_gso_validate_mtu -> skb_gso_validate_network_len
rds: Incorrect reference counting in TCP socket creation
net: ethtool: don't ignore return from driver get_fecparam method
vrf: check forwarding on the original netdevice when generating ICMP dest unreachable
...
When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.
The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.
By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This partially reverts commit 4aea7a5c5e.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts. This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't wake transmit queues if link is not up yet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the initialization order so that the device is ready to transmit
(ie connect vsp is completed) before setting the internal reference
to the device with RCU.
This avoids any races on initialization and prevents retry issues
on shutdown.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_REDIRECT support for mergeable buffer was removed since commit
7324f5399b ("virtio_net: disable XDP_REDIRECT in receive_mergeable()
case"). This is because we don't reserve enough tailroom for struct
skb_shared_info which breaks XDP assumption. So this patch fixes this
by reserving enough tailroom and using fixed size of rx buffer.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we assumed that in case of error when adding FDB entries, the
write operation will fail, but this is not the case. Instead, we need to
check that the number of entries reported in the response is equal to
the number of entries specified in the request.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'default false' should be 'default n', though they happen to have the
same effect here, due to undefined symbols ('false' in this case)
evaluating to n in a tristate sense.
Remove the default instead of changing it. bool and tristate symbols
implicitly default to n.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.
As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were
directed to the broadcast station, however, as the broadcast station
did not have keys configured, these frames were sent unencrypted.
Fix this by using the multicast station which is the station for which
encryption keys are configured.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the GTK is installed, we install it to HW with the
station ID of the AP.
Mac80211 will try to remove it only after the AP sta is
removed, which will result in a failure to remove key
since we do not have any station for it.
This is a valid situation, but a previous commit removed
the early return and added a return with error value, which
resulted in an error message that is confusing to users.
Remove the error return value.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should add the multicast station before adding the
broadcast station.
However, in older FW, the firmware will start beaconing
when we add the multicast station, and since the broadcast
station is not added at this point so the transmission
of the beacon will fail on assert 0x2b00.
This is fixed in later firmware, so make the order
of addition depend on the TLV.
Fixes: 26d6c16bed ("iwlwifi: mvm: add multicast station")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.
Fixes: f5d8f50f27 ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.
Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While entering to D3 mode there is a gap between the time the
driver handles the D3_CONFIG_CMD response to the time the host is going
to sleep.
In between there might be cases which MARKER_CMD can tailgate.
Also during resume flow the MARKER_CMD might get sent while D0I3_CMD
is being handled in the FW.
Cancel MARKER_CMD timer and set it again properly during suspend
resume flows to prevent this command from being sent accidentlly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A toolstack may delete the vif frontend and backend xenstore entries
while xen-netfront is in the removal code path. In that case, the
checks for xenbus_read_driver_state would return XenbusStateUnknown, and
xennet_remove would hang indefinitely. This hang prevents system
shutdown.
xennet_remove must be able to handle XenbusStateUnknown, and
netback_changed must also wake up the wake_queue for that state as well.
Fixes: 5b5971df3b ("xen-netfront: remove warning when unloading module")
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Cc: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.
Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.
However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:
$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1
The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.
Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.
The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.
Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.
Fixes: 9df552ef3e ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables and
also memcpy size_params during devlink resource registration.
Also, introduce a convenient size_param_init helper.
Fixes: ef3116e540 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP_TTL, IP_ECN and IP_DSCP are using the same offset within the
scratchpad as L4 ports. Fix this by shifting all up.
Fixes: 5f57e09091 ("mlxsw: acl: Add ip ttl acl element")
Fixes: i80d0fe4710c ("mlxsw: acl: Add ip tos acl element")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to disable NAPI to prevent a single XDP TX queue being used by
multiple cpus. But we don't check if device is up (NAPI is enabled),
this could result stall because of infinite wait in
napi_disable(). Fixing this by checking device state through
netif_running() before.
Fixes: 4941d472bf ("virtio-net: do not reset during XDP set")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec7711 ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cinterion PL8 is an LTE modem with 2 possible WWAN interfaces.
The modem is controlled via AT commands through the exposed TTYs.
AT^SWWAN write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with AT+CGDCONT. UE supports
two WWAN adapter. Both WWAN adapters can be activated a the same time
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38 ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f5e64032a7 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a7 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't flush batched XDP packets through xdp_do_flush_map(), this
will cause packets stall at TX queue. Consider we don't do XDP on NAPI
poll(), the only possible fix is to call xdp_do_flush_map()
immediately after xdp_do_redirect().
Note, this in fact won't try to batch packets through devmap, we could
address in the future.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for tuntap, all other drivers' XDP was implemented at NAPI
poll() routine in a bh. This guarantees all XDP operation were done at
the same CPU which is required by e.g BFP_MAP_TYPE_PERCPU_ARRAY. But
for tuntap, we do it in process context and we try to protect XDP
processing by RCU reader lock. This is insufficient since
CONFIG_PREEMPT_RCU can preempt the RCU reader critical section which
breaks the assumption that all XDP were processed in the same CPU.
Fixing this by simply disabling preemption during XDP processing.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 762c330d67. The
reason is we try to batch packets for devmap which causes calling
xdp_do_flush() in the process context. Simply disabling preemption
may not work since process may move among processors which lead
xdp_do_flush() to miss some flushes on some processors.
So simply revert the patch, a follow-up patch will add the xdp flush
correctly.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 762c330d67 ("tuntap: add missing xdp flush")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add check for build_skb enabled ring in ixgbe_dma_sync_frag().
In that case &skb_shinfo(skb)->frags[0] may not always be set which
can lead to a crash. Instead we derive the page offset from skb->data.
Fixes: 42073d91a2
("ixgbe: Have the CPU take ownership of the buffers sooner")
CC: stable <stable@vger.kernel.org>
Reported-by: Ambarish Soman <asoman@redhat.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c713fb071e ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:
[10642.528443] BUG: KASAN: use-after-free in
macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352] dump_stack+0x5c/0x7c
[10643.035325] print_address_description+0x75/0x290
[10643.092938] kasan_report+0x28d/0x390
[10643.137971] ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963] macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978] macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532] rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964] kasan_kmalloc+0xa6/0xd0
[10646.343746] kmem_cache_alloc_trace+0xf1/0x210
[10646.397826] macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386] macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728] rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549] __kasan_slab_free+0x138/0x180
[10647.111468] kfree+0x9e/0x1c0
[10647.147869] macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411] rollback_registered_many+0x5b9/0xb10
[10647.268715] rollback_registered+0xd9/0x190
[10647.319675] register_netdevice+0x8eb/0xc70
[10647.370635] macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195] macvtap_newlink+0x171/0x260 [macvtap]
Commit d02fd6e7d2 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d2 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
-----BEGIN PGP SIGNATURE-----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=kwiY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.
Fixes: 34f0f4e3f4 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.
Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resuming from suspend, the PCI device support must re-enable the
interrupt setting so that interrupts are actually delivered.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver implements the ndo_xdp_xmit() function, there is
(currently) no generic way to determine whether it is safe to call.
It is e.g. unsafe to call the drivers ndo_xdp_xmit, if it have not
allocated the needed XDP TX queues yet. This is the case for
virtio_net, which first allocates the XDP TX queues once an XDP/bpf
prog is attached (in virtnet_xdp_set()).
Thus, a crash will occur for virtio_net when redirecting to another
virtio_net device's ndo_xdp_xmit, which have not attached a XDP prog.
The sample xdp_redirect_map tries to attach a dummy XDP prog to take
this into account, but it can also easily fail if the virtio_net (or
actually underlying vhost driver) have not allocated enough extra
queues for the device.
Allocating more queue this is currently a manual config.
Hint for libvirt XML add:
<driver name='vhost' queues='16'>
<host mrg_rxbuf='off'/>
<guest tso4='off' tso6='off' ecn='off' ufo='off'/>
</driver>
The solution in this patch is to check that the device have loaded an
XDP/bpf prog before proceeding. This is similar to the check
performed in driver ixgbe.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_REDIRECT calling xdp_do_redirect() can fail for multiple reasons
(which can be inspected by tracepoints). The current semantics is that
on failure the driver calling xdp_do_redirect() must handle freeing or
recycling the page associated with this frame. This can be seen as an
optimization, as drivers usually have an optimized XDP_DROP code path
for frame recycling in place already.
The virtio_net driver didn't handle when xdp_do_redirect() failed.
This caused a memory leak as the page refcnt wasn't decremented on
failures.
The function __virtnet_xdp_xmit() did handle one type of failure,
when the xmit queue virtqueue_add_outbuf() is full, which "hides"
releasing a refcnt on the page. Instead the function __virtnet_xdp_xmit()
must follow API of xdp_do_redirect(), which on errors leave it up to
the caller to free the page, of the failed send operation.
Fixes: 186b3c998c ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring virtio_net to use the code path 'receive_small()',
in-order to get correct XDP_REDIRECT support, I discovered TCP packets
would get silently dropped when loading an XDP program action XDP_PASS.
The bug seems to be that receive_small() when XDP is loaded check that
hdr->hdr.flags is zero, which seems wrong as hdr.flags contains the
flags VIRTIO_NET_HDR_F_* :
#define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 /* Use csum_start, csum_offset */
#define VIRTIO_NET_HDR_F_DATA_VALID 2 /* Csum is valid */
TCP got dropped as it had the VIRTIO_NET_HDR_F_DATA_VALID flag set.
The flags that are relevant here are the VIRTIO_NET_HDR_GSO_* flags
stored in hdr->hdr.gso_type. Thus, the fix is just check that none of
the gso_type flags have been set.
Fixes: bb91accf27 ("virtio-net: XDP support for small buffers")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virtio_net code have three different RX code-paths in receive_buf().
Two of these code paths can handle XDP, but one of them is broken for
at least XDP_REDIRECT.
Function(1): receive_big() does not support XDP.
Function(2): receive_small() support XDP fully and uses build_skb().
Function(3): receive_mergeable() broken XDP_REDIRECT uses napi_alloc_skb().
The simple explanation is that receive_mergeable() is broken because
it uses napi_alloc_skb(), which violates XDP given XDP assumes packet
header+data in single page and enough tail room for skb_shared_info.
The longer explaination is that receive_mergeable() tries to
work-around and satisfy these XDP requiresments e.g. by having a
function xdp_linearize_page() that allocates and memcpy RX buffers
around (in case packet is scattered across multiple rx buffers). This
does currently satisfy XDP_PASS, XDP_DROP and XDP_TX (but only because
we have not implemented bpf_xdp_adjust_tail yet).
The XDP_REDIRECT action combined with cpumap is broken, and cause hard
to debug crashes. The main issue is that the RX packet does not have
the needed tail-room (SKB_DATA_ALIGN(skb_shared_info)), causing
skb_shared_info to overlap the next packets head-room (in which cpumap
stores info).
Reproducing depend on the packet payload length and if RX-buffer size
happened to have tail-room for skb_shared_info or not. But to make
this even harder to troubleshoot, the RX-buffer size is runtime
dynamically change based on an Exponentially Weighted Moving Average
(EWMA) over the packet length, when refilling RX rings.
This patch only disable XDP_REDIRECT support in receive_mergeable()
case, because it can cause a real crash.
IMHO we should consider NOT supporting XDP in receive_mergeable() at
all, because the principles behind XDP are to gain speed by (1) code
simplicity, (2) sacrificing memory and (3) where possible moving
runtime checks to setup time. These principles are clearly being
violated in receive_mergeable(), that e.g. runtime track average
buffer size to save memory consumption.
In the longer run, we should consider introducing a separate receive
function when attaching an XDP program, and also change the memory
model to be compatible with XDP when attaching an XDP prog.
Fixes: 186b3c998c ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJajJahAAoJEEg/ir3gV/o+PTQIALd4/l5VEU1vWqXp6PPaIaRP
fCt4CKXkeIozyOhkiaYLcNAvPnsJRi54a/PGyUbHwxadkjuOhS8WETyQwMf8gbKF
g+LTDseqKjWcu6fUMqe7TmjrNHSo2VErjOjHw1+7emKSkBZuc8zBBND9PqHtOQY6
f1KoUY6IBs22dwqzynxkC5A62VQbTYd0FPnf1n9wN8ubFXSb37KUgKoW4kmMFmLe
JsYEcsAKxpfepnP+EYLyDrVcT1LA9edi5DI5uxSfNgas6bTtjRPhtyZCznDF8rly
jEWv3O2c+HhchuysoACTLiTllviHGj0Myv+rGb0ouhjZWMtulgPPQ04lbYjjr84=
=uF0v
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-02-20
The following pull request includes some fixes for the mlx5 core and
netdevice driver.
Please pull and let me know if there's any issue.
-stable 4.10.y:
('net/mlx5e: Fix loopback self test when GRO is off')
-stable 4.12.y:
('net/mlx5e: Specify numa node when allocating drop rq')
-stable 4.13.y:
('net/mlx5e: Verify inline header size do not exceed SKB linear size')
-stable 4.15.y:
('net/mlx5e: Fix TCP checksum in LRO buffers')
('net/mlx5: Fix error handling when adding flow rules')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If building match list or adding existing fg fails when
node is locked, function returned without unlocking it.
This happened if node version changed or adding existing fg
returned with EAGAIN after jumping to search_again_locked label.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
First use of drop counters happens in esw_apply_vport_conf function,
while they are allocated later in the flow. Fix that by moving
esw_vport_create_drop_counters function to be called before the first use.
Fixes: b8a0dbe3a9 ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can't allow only some of the rules sharing an FTE to ask for
header re-write, add it to the conflicting action checks.
Fixes: 0d235c3fab ('net/mlx5: Add hash table to search FTEs in a flow-group')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The adapter uses the cache_line_128byte setting to set the bounds for
end padding. On systems where the cacheline size is greater than 128B
use 128B instead of the default of 64B. This results in fewer partial
cacheline writes. There's a 50% chance it will pad to the end of a 256B
cache line vs only 25% when using 64B.
Fixes: f32f5bd2eb ("net/mlx5: Configure cache line size for start and end padding")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When allocating a drop rq, no numa node is explicitly set which means
allocations are done on node zero. This is not necessarily the nearest
numa node to the HCA, and even worse, might even be a memoryless numa
node.
Choose the numa_node given to us by the pci device in order to properly
allocate the coherent dma memory instead of assuming zero is valid.
Fixes: 556dd1b9c3 ("net/mlx5e: Set drop RQ's necessary parameters only")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This isn't supported when we emulate eswitch vlan push action which
is the current state of things.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:
[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.
Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.
This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.
Fixes: 6aace17e64 ("net/mlx5e: Fix inline header size for small packets")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When GRO is off, the transport header pointer in sk_buff is
initialized to network's header.
To find the udp header, instead of using udp_hdr() which assumes
skb_network_header was set, manually calculate the udp header offset.
Fixes: 0952da791c ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed. We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.
Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).
This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.
It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After introduction of commit d0869c0071, there were some instances of
RX queue entries from a previous session (before the device was closed
and reopened) returned to the NAPI polling routine. Since the corresponding
socket buffers were freed, this resulted in a panic on reopen. Include
a check for a NULL skb here to avoid this.
Fixes: d0869c0071 ("ibmvnic: Clean RX pool buffers during device close")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89f ("mlxsw: spectrum_router: Provide offload indication using nexthop flags")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c457 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
BUG: sleeping function called from invalid context
in_atomic(): 0, irqs_disabled(): 0, pid: 5762, name: ip
Preemption disabled at:
[<ffffff9d49043564>] debug_object_active_state+0xa4/0x16c
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
PC is at ___might_sleep+0x13c/0x180
LR is at ___might_sleep+0x17c/0x180
[<ffffff9d48ce0924>] ___might_sleep+0x13c/0x180
[<ffffff9d48ce09c0>] __might_sleep+0x58/0x8c
[<ffffff9d49d6253c>] mutex_lock+0x2c/0x48
[<ffffff9d48ed4840>] kernfs_remove_by_name_ns+0x48/0xa8
[<ffffff9d48ed6ec8>] sysfs_remove_link+0x30/0x58
[<ffffff9d49b05840>] __netdev_adjacent_dev_remove+0x14c/0x1e0
[<ffffff9d49b05914>] __netdev_adjacent_dev_unlink_lists+0x40/0x68
[<ffffff9d49b08820>] netdev_upper_dev_unlink+0xb4/0x1fc
[<ffffff9d494a29f0>] rmnet_dev_walk_unreg+0x6c/0xc8
[<ffffff9d49b00b40>] netdev_walk_all_lower_dev_rcu+0x58/0xb4
[<ffffff9d494a30fc>] rmnet_config_notify_cb+0xf4/0x134
[<ffffff9d48cd21b4>] raw_notifier_call_chain+0x58/0x78
[<ffffff9d49b028a4>] call_netdevice_notifiers_info+0x48/0x78
[<ffffff9d49b0b568>] rollback_registered_many+0x230/0x3c8
[<ffffff9d49b0b738>] unregister_netdevice_many+0x38/0x94
[<ffffff9d49b1e110>] rtnl_delete_link+0x58/0x88
[<ffffff9d49b201dc>] rtnl_dellink+0xbc/0x1cc
[<ffffff9d49b2355c>] rtnetlink_rcv_msg+0xb0/0x244
[<ffffff9d49b5230c>] netlink_rcv_skb+0xb4/0xdc
[<ffffff9d49b204f4>] rtnetlink_rcv+0x34/0x44
[<ffffff9d49b51af0>] netlink_unicast+0x1ec/0x294
[<ffffff9d49b51fdc>] netlink_sendmsg+0x320/0x390
[<ffffff9d49ae6858>] sock_sendmsg+0x54/0x60
[<ffffff9d49ae6f94>] ___sys_sendmsg+0x298/0x2b0
[<ffffff9d49ae98f8>] SyS_sendmsg+0xb4/0xf0
[<ffffff9d48c83770>] el0_svc_naked+0x24/0x28
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're obviously not part of a memory reclaim path, so don't set the flag.
This also causes a warning in check_flush_dependency() since we end up
in a code path that flushes a non-reclaim workqueue, and we shouldn't do
that if we were really part of reclaim.
Reported-by: syzbot+41cdaf4232c50e658934@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
<Mark Rutland reported>
While fuzzing arm64 v4.16-rc1 with Syzkaller, I've been hitting a
misaligned atomic in __skb_clone:
atomic_inc(&(skb_shinfo(skb)->dataref));
where dataref doesn't have the required natural alignment, and the
atomic operation faults. e.g. i often see it aligned to a single
byte boundary rather than a four byte boundary.
AFAICT, the skb_shared_info is misaligned at the instant it's
allocated in __napi_alloc_skb() __napi_alloc_skb()
</end of report>
Problem is caused by tun_napi_alloc_frags() using
napi_alloc_frag() with user provided seg sizes,
leading to other users of this API getting unaligned
page fragments.
Since we would like to not necessarily add paddings or alignments to
the frags that tun_napi_alloc_frags() attaches to the skb, switch to
another page frag allocator.
As a bonus skb_page_frag_refill() can use GFP_KERNEL allocations,
meaning that we can not deplete memory reserves as easily.
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794c ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger
David S. Miller
Arkadi Sharshevsky
Ganesh Goudar
Jeremy Linton
Hemanth Puranik
Michal Kalderon
Eric Dumazet
Denis Kirjanov
Arend Van Spriel
Randy Dunlap
Florian Fainelli
Pierre-Yves Kerbrat
Linus Torvalds
Benjamin Poirier
Jason Wang
Guillaume Nault
Shalom Toledo
Ulf Magnusson
Ilan Peer
Sara Sharon
Shaul Triebitz
Andrei Otcheretianski
Haim Dreyfuss
Jason Andryuk
Ido Schimmel
Jiri Pirko
Claudiu Manoil
Bassem Boubaker
Sergei Shtylyov
Andrew Lunn
Denis Du
Emil Tantilov
Larry Finger
Andy Spencer
Alexey Kodanev
Dan Carpenter
Thomas Falcon
Finn Thain
Tom Lendacky
Jesper Dangaard Brouer
Vlad Buslov
Eugenia Emantayev
Or Gerlitz
Daniel Jurgens
Gal Pressman
Eran Ben Elisha
Inbar Karmy
Prashant Sreedharan
Subash Abhinov Kasiviswanathan
Johannes Berg
Casey Leedom