With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Power values in the 100s of watt range can easily blow past
32bit math limits when processing everything in microwatts.
Use 64bit math instead to avoid these issues on common 32bit ARM
BMC platforms.
Fixes: 442aba7872 ("hwmon: PMBus device driver")
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Drivers for MAX31785 and MAX6621
- Support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- Various driver cleanups and minor improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NpxT
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- drivers for MAX31785 and MAX6621
- support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- various driver cleanups and minor improvements
* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
dt-bindings: pmbus: Add Maxim MAX31785 documentation
pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
hwmon: (aspeed-pwm-tacho) Sort headers
hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
hwmon: (max6621) Inverted if condition in max6621_read()
hwmon: (asc7621) remove redundant assignment to newval
hwmon: (xgene) Support hwmon v2
hwmon: (gpio-fan) Fix null pointer dereference at probe
hwmon: (gpio-fan) Convert to use GPIO descriptors
hwmon: (gpio-fan) Rename GPIO line state variables
hwmon: (gpio-fan) Get rid of the gpio alarm struct
hwmon: (gpio-fan) Get rid of platform data struct
hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
hwmon: (gpio-fan) Send around device pointer
hwmon: (gpio-fan) Localize platform data
hwmon: (gpio-fan) Use local variable pointers
hwmon: (gpio-fan) Move DT bindings to the right place
Documentation: devicetree: add max6621 device
hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
hwmon: (w83793) make const array watchdog_minors static, reduces object code size
...
The Maxim MAX31785 is a PMBus device providing closed-loop, multi-channel
fan management with temperature and remote voltage sensing. It supports
various fan control features, including PWM frequency control, temperature
hysteresis, dual tachometer measurements, and fan health monitoring.
This patch presents a basic driver using only the existing features of the
PMBus subsystem.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
[groeck: Modified description to clarify that fan control is not yet provided]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the un-necessary ifdef CONFIG_ACPI and directly
uses the acpi_match_table from the driver pdev.
Signed-off-by: Hoan Tran <hotran@apm.com>
[groeck: Dropped unnecessary initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We intended to test for failure here but accidentally tested for
success. It means that we don't set "*val" to true and it means that
if i2c_smbus_write_byte() does fail then we return success.
Fixes: e7895864b0d7 ("hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The setting of newval to zero is redundant as the following if/else
stanzas will always update newval to a new value. Remove the
redundant setting, cleans up clang build warning:
drivers/hwmon/asc7621.c:582:2: warning: Value stored to 'newval' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch supports xgene-hwmon v2 which uses the non-cachable memory
as the PCC shared memory.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit changed the argument list of gpio_fan_get_of_data(),
removing the "struct *dev" argument and retrieving it instead from the
gpio_fan_data structure. The "dev" entry of gpio_fan_data was then
dereferenced to access the of_node field, leading to a kernel panic
during the probe as the "dev" entry of the gpio_fan_data structure was
not filled yet.
Fix this by setting fan_data->dev before calling gpio_fan_get_of_data().
Fixes: 5859d8d30737 ("hwmon: (gpio-fan) Get rid of platform data struct")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This converts the GPIO fan driver to use GPIO descriptors. This way
we avoid indirection since the gpiolib anyway just use descriptors
inside, and we also get rid of explicit polarity handling: the
descriptors internally knows if the line is active high or active
low.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[groeck: Line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "ctrl" and "num_ctrl" entries in the state container struct is
ambiguously named "ctrl" and "num_ctrl" overlapping with some hwmon
lingo and making it hard to understand. Since this array actually
contains the GPIO line numbers, from the Linux global GPIO numberspace,
used to control the different fan speeds. Rename these fields to
"gpios" (pluralis) and "num_gpios" so as to make it unambiguous.
Convert some instances of "unsigned" to "unsigned int" to keep
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no point in storing the GPIO alarm settings in their
own struct so merge this into the main state container.
Convert the variables from "unsigned" to "unsigned int" to
make checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We are not passing the platform data struct into the driver from the
outside, there is no point of having it around separately so instead
of first populating the platform data struct and assigning the result
into the same variables in the state container (struct gpio_fan_data)
just assign the configuration from the device tree directly into the
state container members.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have no users of platform data, we made platform data driver-local,
so cut all #ifdefs for the platform data case, and depend on the
Kconfig CONFIG_OF_GPIO symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver is storing the struct platform_device *pdev pointer
but what it is really using and want to pass around is a
struct device *dev pointer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is not a single user of the platform data header in
<linux/gpio-fan.h>. We can conclude that all current users are
probing from the device tree, so start simplifying the code by
pulling the header into the driver.
Convert "unsigned" to "unsigned int" in the process to make
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Create local struct device *dev and device_node *np pointers to
make the code easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate const array watchdog_minors on the stack, instead make it
static. Makes the object code smaller by over 350 bytes:
Before:
text data bss dec hex filename
48019 38144 256 86419 15193 drivers/hwmon/w83793.o
After:
text data bss dec hex filename
47574 38232 256 86062 1502e drivers/hwmon/w83793.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previous value reduced the time required to determine
the fan value, however, it's also used as the final timeout
mechanism. The prevous value would work for any fan speed
greater than around 3k RPM. This increased value, lets the fan
speeds return quickly but will wait longer to handle speeds below 3k
RPM.
Testing: this value was determined through experimentation on the ast2400
on the Quanta-q71l. This configurations runs 8 fans attached to the
controller.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new device tree binding for max1619.
Signed-off-by: Alan Tull <atull@kernel.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit removed bit or'ing into to the integer status
so now status is now always zero. This means that the non-zero check on
status and the sht15_send_status call will never occur; it is deadcode.
Clean this up by removing the dead code.
Detected by: CoverityScan CID#1456835 ("Logically dead code")
Fixes: aa7ab80c578c ("hwmon: (sht15) Root out platform data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After finding out there are active users of this sensor I noticed:
- It has a single PXA27x board file using the platform data
- The platform data is only used to carry two GPIO pins, all other
fields are unused
- The driver does not use GPIO descriptors but the legacy GPIO
API
I saw we can swiftly fix this by:
- Killing off the platform data entirely
- Define a GPIO descriptor lookup table in the board file
- Use the standard devm_gpiod_get() to grab the GPIO descriptors
from either the device tree or the board file table.
This compiles, but needs testing.
Cc: arm@kernel.org
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Davide Hug <d@videhug.ch>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handling temperature offset values for various AMD CPUs,
similar to the code used in the coretemp driver for Intel CPUs. This is
primarily for Ryzen CPUs (which has documented temperature offsets),
but the code is kept generic to simplify adding additional CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce a local data structure and determine the temperature read
function at probe time to reduce runtime complexity.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function snprintf already cares for the terminating NUL at the end of
the string, the caller doesn't need to do it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andrea Merello <andrea.merello@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core may call read/write word data functions with a page value
of -1, intending to perform the operation without setting the page.
However, the read/write word data functions accept only unsigned 8-bit
page numbers, and therefore cannot check for negative page number to
avoid setting the page. This results in setting the page number to 0xFF.
This may result in errors or undefined behavior of some devices
(specifically the ir35221, which allows the page to be set to 0xFF,
but some subsequent operations to read registers may fail).
Switch the pmbus_set_page page parameter to an integer and perform the
check for negative page there. Make read/write functions consistent in
accepting an integer page number parameter.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Fixes: cbcdec6202 ("hwmon: (pmbus): Access word data for STATUS_WORD")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read
delay") reduced the initial temperature read delay and made it dependent
on the chip's shutdown mode. If the chip was not in shutdown mode at probe,
the read delay no longer applies.
This ignores the fact that the chip initialization changes the temperature
sensor resolution, and that the temperature register values change when
the resolution is changed. As a result, the reported temperature is twice
as high as the real temperature until the first temperature conversion
after the configuration change is complete. This can result in unexpected
behavior and, worst case, in a system shutdown. To fix the problem,
let's just always wait for a conversion to complete before reporting
a temperature.
Fixes: 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read delay")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197167
Reported-by: Ralf Goebel <ralf.goebel@imago-technologies.com>
Cc: Ralf Goebel <ralf.goebel@imago-technologies.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TSI channel, which is usually used for touchscreen support, but can
be used as 4 general purpose ADCs. When used as a touchscreen interface
the touchscreen driver switches the device into 1ms sampling mode (rather
than the default 10ms economy mode) as recommended by the manufacturer.
When using the TSI channels as a general purpose ADC we are currently not
doing this and testing suggests that this can result in ADC timeouts:
[ 5827.198289] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5827.728293] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5993.808335] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.328441] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.848291] da9052 spi2.0: timeout waiting for ADC conversion interrupt
Switching to the 1ms timing resolves this issue.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 2ca492e22c has moved the call to 'kfifo_alloc()' from after the
main 'if' statement to before it.
But it has not updated the error handling paths accordingly.
Fix all that:
- if 'kfifo_alloc()' fails we can return directly
- direct returns after 'kfifo_alloc()' must now go to 'out_mbox_free'
- 'goto out_mbox_free' must be replaced by 'goto out', otherwise the
'[pcc_]mbox_free_channel()' call will be missed.
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by over 950 bytes:
Before:
text data bss dec hex filename
26144 18768 352 45264 b0d0 drivers/hwmon/asc7621.o
After:
text data bss dec hex filename
25029 18928 352 44309 ad15 drivers/hwmon/asc7621.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TI LM5066I hotswap controller is a more accurate version of the
LM5066 device already supported. It has different measurement conversion
coefficients than the LM5066, so it needs to be recognized as a
different device.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When converting the DIRECT format CURRENT_IN and POWER commands, make
the offset coefficient ("b") predicate on the value of the current limit
setting.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps:
- VR13.0 mode, 10-mV DAC - 0x24
- VR13.0 mode, 5-mV DAC - 0x27
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor IBM CFF power supplies with hwmon over
pmbus.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: drop 'default n'; include bitops.h instead of jiffies.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TSI channel has a 4 channel mux connected to it and is normally
used for touchscreen support. The hardware may alternatively
use it as general purpose adc.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Rosin
Robert Lippert
Andy Shevchenko
Guenter Roeck
Linus Torvalds
Andrew Jeffery
Joel
Greg Kroah-Hartman
hotran
Dan Carpenter
Colin Ian King
Miquel Raynal
Linus Walleij
Vadim Pasternak
Patrick Venture
Alan Tull
Jean Delvare
Edward A. James
Martyn Welch
Christophe Jaillet
Christoph Hellwig
Florian Eckert
Xo Wang
Arvind Yadav
Sebastian Reichel