Direct IO can be used in case of hardware encryption. The following
scenario results into data corruption issue in this path -
Thread A - Thread B-
-> write file#1 in direct IO
-> GC gets kicked in
-> GC submitted bio on meta mapping
for file#1, but pending completion
-> write file#1 again with new data
in direct IO
-> GC bio gets completed now
-> GC writes old data to the new
location and thus file#1 is
corrupted.
Fix this by submitting and waiting for pending io on meta mapping
for direct IO case in f2fs_map_blocks().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We need to drop PG_checked flag on page as well when we clear PG_uptodate
flag, in order to avoid treating the page as GCing one later.
Signed-off-by: Weichao Guo <guoweichao@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As rbtree supports caching leftmost node natively, update f2fs codes
to use rb_*_cached helpers to speed up leftmost node visiting.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Note that, it requires "f2fs: return correct errno in f2fs_gc".
This adds a lightweight non-persistent snapshotting scheme to f2fs.
To use, mount with the option checkpoint=disable, and to return to
normal operation, remount with checkpoint=enable. If the filesystem
is shut down before remounting with checkpoint=enable, it will revert
back to its apparent state when it was first mounted with
checkpoint=disable. This is useful for situations where you wish to be
able to roll back the state of the disk in case of some critical
failure.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
[Jaegeuk Kim: use SB_RDONLY instead of MS_RDONLY]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There is one case that we can leave bio in f2fs, result in hanging
page writeback waiter.
Thread A Thread B
- f2fs_write_cache_pages
- f2fs_submit_page_write
page #0 cached in bio #0 of cold log
- f2fs_submit_page_write
page #1 cached in bio #1 of warm log
- f2fs_write_cache_pages
- f2fs_submit_page_write
bio is full, submit bio #1 contain page #1
- f2fs_submit_merged_write_cond(, page #1)
fail to submit bio #0 due to page #1 is not in any cached bios.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch supports to account meta IO, it enables to show write IO
from f2fs more comprehensively via 'status' debugfs entry.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch avoids BUG_ON when f2fs_get_meta_page_nofail got EIO during
xfstests/generic/475.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This helps to control the frequency of submission of discard and
GC requests independently, based on the need.
Suggested-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Remove the verbose license text from f2fs files and replace them with
SPDX tags. This does not change the license of any of the code.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
1. Create a file in an encrypted directory
2. Do GC & drop caches
3. Read stale data before its bio for metapage was not issued yet
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Don't limit printing log, so that we will not miss any key messages.
This reverts commit a36c106dff.
In addition, we use printk_ratelimited to avoid too many log prints.
- error injection
- discard submission failure
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When dev is busy, discard thread wake up timeout can be aligned with the
exact time that it needs to wait for dev to come out of busy. This helps
to avoid unnecessary periodic wakeups and thus save some power.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
https://bugzilla.kernel.org/show_bug.cgi?id=200951
These is a NULL pointer dereference issue reported in bugzilla:
Hi,
in the setup there is a SATA SSD connected to a SATA-to-USB bridge.
The disc is "Samsung SSD 850 PRO 256G" which supports TRIM.
There are four partitions:
sda1: FAT /boot
sda2: F2FS /
sda3: F2FS /home
sda4: F2FS
The bridge is ASMT1153e which uses the "uas" driver.
There is no TRIM pass-through, so, when mounting it reports:
mounting with "discard" option, but the device does not support discard
The USB host is USB3.0 and UASP capable. It is the one on RK3399.
Given this everything works fine, except there is no TRIM support.
In order to enable TRIM a new UDEV rule is added [1]:
/etc/udev/rules.d/10-sata-bridge-trim.rules:
ACTION=="add|change", ATTRS{idVendor}=="174c", ATTRS{idProduct}=="55aa", SUBSYSTEM=="scsi_disk", ATTR{provisioning_mode}="unmap"
After reboot any F2FS write hangs forever and dmesg reports:
Unable to handle kernel NULL pointer dereference
Also tested on a x86_64 system: works fine even with TRIM enabled.
same disc
same bridge
different usb host controller
different cpu architecture
not root filesystem
Regards,
Vicenç.
[1] Post #5 in https://bbs.archlinux.org/viewtopic.php?id=236280
Unable to handle kernel NULL pointer dereference at virtual address 000000000000003e
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000626e3122
[000000000000003e] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: overlay snd_soc_hdmi_codec rc_cec dw_hdmi_i2s_audio dw_hdmi_cec snd_soc_simple_card snd_soc_simple_card_utils snd_soc_rockchip_i2s rockchip_rga snd_soc_rockchip_pcm rockchipdrm videobuf2_dma_sg v4l2_mem2mem rtc_rk808 videobuf2_memops analogix_dp videobuf2_v4l2 videobuf2_common dw_hdmi dw_wdt cec rc_core videodev drm_kms_helper media drm rockchip_thermal rockchip_saradc realtek drm_panel_orientation_quirks syscopyarea sysfillrect sysimgblt fb_sys_fops dwmac_rk stmmac_platform stmmac pwm_bl squashfs loop crypto_user gpio_keys hid_kensington
CPU: 5 PID: 957 Comm: nvim Not tainted 4.19.0-rc1-1-ARCH #1
Hardware name: Sapphire-RK3399 Board (DT)
pstate: 00000005 (nzcv daif -PAN -UAO)
pc : update_sit_entry+0x304/0x4b0
lr : update_sit_entry+0x108/0x4b0
sp : ffff00000ca13bd0
x29: ffff00000ca13bd0 x28: 000000000000003e
x27: 0000000000000020 x26: 0000000000080000
x25: 0000000000000048 x24: ffff8000ebb85cf8
x23: 0000000000000253 x22: 00000000ffffffff
x21: 00000000000535f2 x20: 00000000ffffffdf
x19: ffff8000eb9e6800 x18: ffff8000eb9e6be8
x17: 0000000007ce6926 x16: 000000001c83ffa8
x15: 0000000000000000 x14: ffff8000f602df90
x13: 0000000000000006 x12: 0000000000000040
x11: 0000000000000228 x10: 0000000000000000
x9 : 0000000000000000 x8 : 0000000000000000
x7 : 00000000000535f2 x6 : ffff8000ebff3440
x5 : ffff8000ebff3440 x4 : ffff8000ebe3a6c8
x3 : 00000000ffffffff x2 : 0000000000000020
x1 : 0000000000000000 x0 : ffff8000eb9e5800
Process nvim (pid: 957, stack limit = 0x0000000063a78320)
Call trace:
update_sit_entry+0x304/0x4b0
f2fs_invalidate_blocks+0x98/0x140
truncate_node+0x90/0x400
f2fs_remove_inode_page+0xe8/0x340
f2fs_evict_inode+0x2b0/0x408
evict+0xe0/0x1e0
iput+0x160/0x260
do_unlinkat+0x214/0x298
__arm64_sys_unlinkat+0x3c/0x68
el0_svc_handler+0x94/0x118
el0_svc+0x8/0xc
Code: f9400800 b9488400 36080140 f9400f01 (387c4820)
---[ end trace a0f21a307118c477 ]---
The reason is it is possible to enable discard flag on block queue via
UDEV, but during mount, f2fs will initialize se->discard_map only if
this flag is set, once the flag is set after mount, f2fs may dereference
NULL pointer on se->discard_map.
So this patch does below changes to fix this issue:
- initialize and update se->discard_map all the time.
- don't clear DISCARD option if device has no QUEUE_FLAG_DISCARD flag
during mount.
- don't issue small discard on zoned block device.
- introduce some functions to enhance the readability.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The f2fs_gc() called by f2fs_balance_fs() requires to be called outside of
fi->i_gc_rwsem[WRITE], since f2fs_gc() can try to grab it in a loop.
If it hits the miximum retrials in GC, let's give a chance to release
gc_mutex for a short time in order not to go into live lock in the worst
case.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This reverts the commit - "b93f771 - f2fs: remove writepages lock"
to fix the drop in sequential read throughput.
Test: ./tiotest -t 32 -d /data/tio_tmp -f 32 -b 524288 -k 1 -k 3 -L
device: UFS
Before -
read throughput: 185 MB/s
total read requests: 85177 (of these ~80000 are 4KB size requests).
total write requests: 2546 (of these ~2208 requests are written in 512KB).
After -
read throughput: 758 MB/s
total read requests: 2417 (of these ~2042 are 512KB reads).
total write requests: 2701 (of these ~2034 requests are written in 512KB).
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When CONFIG_F2FS_FAULT_INJECTION is disabled, we get a warning about an
unused label:
fs/f2fs/segment.c: In function '__submit_discard_cmd':
fs/f2fs/segment.c:1059:1: error: label 'submit' defined but not used [-Werror=unused-label]
This could be fixed by adding another #ifdef around it, but the more
reliable way of doing this seems to be to remove the other #ifdefs
where that is easily possible.
By defining time_to_inject() as a trivial stub, most of the checks for
CONFIG_F2FS_FAULT_INJECTION can go away. This also leads to nicer
formatting of the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As Dan Carpenter reported:
The patch 20ee4382322c: "f2fs: issue small discard by LBA order" from
Jul 8, 2018, leads to the following Smatch warning:
fs/f2fs/segment.c:1277 __issue_discard_cmd_orderly()
warn: 'dc' was already freed.
See also:
fs/f2fs/segment.c:2550 __issue_discard_cmd_range() warn: 'dc' was already freed.
In order to fix this issue, let's get error from __submit_discard_cmd(),
and release current discard command after we referenced next one.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds to support discard submission error injection for testing
error handling of __submit_discard_cmd().
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Some devices has small max_{hw,}discard_sectors, so that in
__blkdev_issue_discard(), one big size discard bio can be split
into multiple small size discard bios, result in heavy load in IO
scheduler and device, which can hang other sync IO for long time.
Now, f2fs is trying to control discard commands more elaboratively,
in order to make less conflict in between discard IO and user IO
to enhance application's performance, so in this patch, we will
split discard bio in f2fs in prior to in block layer to reduce
issuing multiple discard bios in a short time.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
generic/260 reported below error:
[+] Default length with start set (should succeed)
[+] Length beyond the end of fs (should succeed)
[+] Length beyond the end of fs with start set (should succeed)
+./tests/generic/260: line 94: [: 18446744073709551615: integer expression expected
+./tests/generic/260: line 104: [: 18446744073709551615: integer expression expected
Test done
...
In f2fs_trim_fs(), if there is no discard being trimmed, we need to correct
range->len before return.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Fsyncer will wait on all dnode pages of regular writeback before flushing,
if there are async dnode pages blocked by IO scheduler, it may decrease
fsync's performance.
In this patch, we choose to let f2fs_balance_fs_bg() to trigger checkpoint
to flush these dnode pages of regular, so async IO of dnode page can be
elimitnated, making fsyncer only need to wait for sync IO.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For the case when sbi->segs_per_sec > 1 with lfs mode, take
section:segment = 5 for example, if the section prefree_map is
...previous section | current section (1 1 0 1 1) | next section...,
then the start = x, end = x + 1, after start = start_segno +
sbi->segs_per_sec, start = x + 5, then it will skip x + 3 and x + 4, but
their bitmap is still set, which will cause duplicated
f2fs_issue_discard of this same section in the next write_checkpoint:
round 1: section bitmap : 1 1 1 1 1, all valid, prefree_map: 0 0 0 0 0
then rm data block NO.2, block NO.2 becomes invalid, prefree_map: 0 0 1 0 0
write_checkpoint: section bitmap: 1 1 0 1 1, prefree_map: 0 0 0 0 0,
prefree of NO.2 is cleared, and no discard issued
round 2: rm data block NO.0, NO.1, NO.3, NO.4
all invalid, but prefree bit of NO.2 is set and cleared in round 1, then
prefree_map: 1 1 0 1 1
write_checkpoint: section bitmap: 0 0 0 0 0, prefree_map: 0 0 0 1 1, no
valid blocks of this section, so discard issued, but this time prefree
bit of NO.3 and NO.4 is skipped due to start = start_segno + sbi->segs_per_sec;
round 3:
write_checkpoint: section bitmap: 0 0 0 0 0, prefree_map: 0 0 0 1 1 ->
0 0 0 0 0, no valid blocks of this section, so discard issued,
this time prefree bit of NO.3 and NO.4 is cleared, but the discard of
this section is sent again...
To fix this problem, we can align the start and end value to section
boundary for fstrim and real-time discard operation, and decide to issue
discard only when the whole section is invalid, which can issue discard
aligned to section size as much as possible and avoid redundant discard.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If caller of __get_meta_page() can handle error, let's propagate error
from __get_meta_page().
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For small granularity discard which size is smaller than 64KB, if we
issue those kind of discards orderly by size, their IOs will be spread
into entire logical address, so that in FTL, L2P table will be updated
randomly, result bad wear rate in the table.
In this patch, we choose to issue small discard by LBA order, by this
way, we can expect that L2P table updates from adjacent discard IOs can
be merged in the cache, so it can reduce lifetime wearing of flash.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For background discard policy, even if there is queued user IO, still
we will check max_requests times for next discard entry, it is unneeded,
let's just stop this round submission immediately.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We should account trimmed block number from __wait_all_discard_cmd
in __issue_discard_cmd_range, otherwise trimmed blocks returned
by f2fs_trim_fs will be wrong, this patch fixes it.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If there is millions of discard entries cached in rb tree, each
sanity check of it can cause very long latency as held cmd_lock
blocking other lock grabbers.
In other aspect, we have enabled the check very long time, as
we see, there is no such inconsistent condition caused by bugs.
But still we do not choose to kill it directly, instead, adding
an flag to disable the check now, if there is related code change,
we can reuse it to detect bugs.
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces verify_blkaddr to check meta/data block address
with valid range to detect bug earlier.
In addition, once we encounter an invalid blkaddr, notice user to run
fsck to fix, and let the kernel panic.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Actually, we don't need to issue discard commands, if discard is on, as
mentioned in the comment.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we change system time to the past, get_mtime() will return a
overflowed time, and SIT_I(sbi)->max_mtime will be udpated
incorrectly, this patch fixes the two issues.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As Ted reported:
"Hi, I was looking at f2fs's sources recently, and I noticed that there
is a very large number of non-static symbols which don't have a f2fs
prefix. There's well over a hundred (see attached below).
As one example, in fs/f2fs/dir.c there is:
unsigned char get_de_type(struct f2fs_dir_entry *de)
This function is clearly only useful for f2fs, but it has a generic
name. This means that if any other file system tries to have the same
symbol name, there will be a symbol conflict and the kernel would not
successfully build. It also means that when someone is looking f2fs
sources, it's not at all obvious whether a function such as
read_data_page(), invalidate_blocks(), is a generic kernel function
found in the fs, mm, or block layers, or a f2fs specific function.
You might want to fix this at some point. Hopefully Kent's bcachefs
isn't similarly using genericly named functions, since that might
cause conflicts with f2fs's functions --- but just as this would be a
problem that we would rightly insist that Kent fix, this is something
that we should have rightly insisted that f2fs should have fixed
before it was integrated into the mainline kernel.
acquire_orphan_inode
add_ino_entry
add_orphan_inode
allocate_data_block
allocate_new_segments
alloc_nid
alloc_nid_done
alloc_nid_failed
available_free_memory
...."
This patch adds "f2fs_" prefix for all non-static symbols in order to:
a) avoid conflict with other kernel generic symbols;
b) to indicate the function is f2fs specific one instead of generic
one;
Reported-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
- f2fs_fill_super
- recover_fsync_data
- recover_data
- del_fsync_inode
- iput
- iput_final
- write_inode_now
- f2fs_write_inode
- f2fs_balance_fs
- f2fs_balance_fs_bg
- sync_dirty_inodes
With data_flush mount option, during recovery, in order to avoid entering
above writeback flow, let's detect recovery status and do skip in
f2fs_balance_fs_bg.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If SBI_NEED_FSCK is set, discard_wake will never be cleared. As a
result, the condition of wait_event_interruptible_timeout() is always
true, which gets discard thread run too frequently.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
f2fs doesn't allow abuse on atomic write class interface, so except
limiting in-mem pages' total memory usage capacity, we need to limit
atomic-write usage as well when filesystem is seriously fragmented,
otherwise we may run into infinite loop during foreground GC because
target blocks in victim segment are belong to atomic opened file for
long time.
Now, we will detect failure due to atomic write in foreground GC, if
the count exceeds threshold, we will drop all atomic written data in
cache, by this, I expect it can keep our system running safely to
prevent Dos attack.
In addition, his patch adds to show GC skip information in debugfs,
now it just shows count of skipped caused by atomic write.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For non-migration IO, we will keep order of data/node blocks' submitting
as allocation sequence by sorting IOs in per log io_list list, but for
migration IO, it could be out-of-order.
In LFS mode, we should keep all IOs including migration IO be ordered,
so that this patch fixes to add an additional lock to keep submitting
order.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
After revoking atomic write, related LBA can be reused by others, so we
need to wait page writeback before reusing the LBA, in order to avoid
interference between old atomic written in-flight IO and new IO.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
- rename is_valid_blkaddr() to is_valid_meta_blkaddr() for readability.
- introduce is_valid_blkaddr() for cleanup.
No logic change in this patch.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Since sit_i.min_mtime's type is unsigned long long, so we should
initialize it with max value of the type ULLONG_MAX instead of
LLONG_MAX.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Volatile file's data will be updated oftenly, so it'd better to place
its data into hot data segment.
In addition, for atomic file, we change to check FI_ATOMIC_FILE instead
of FI_HOT_DATA to make code readability better.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Introduce release_discard_addr() to include common codes for cleanup.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Fengguang Wu: declare static function, reported by kbuild test robot]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In build_sit_entries(), if valid_blocks in SIT block is smaller than
valid_blocks in journal, for below calculation:
sbi->discard_blks += old_valid_blocks - se->valid_blocks;
There will be two times potential overflow:
- old_valid_blocks - se->valid_blocks will overflow, and be a very
large number.
- sbi->discard_blks += result will overflow again, comes out a correct
result accidently.
Anyway, it should be fixed.
Fixes: d600af236d ("f2fs: avoid unneeded loop in build_sit_entries")
Fixes: 1f43e2ad7b ("f2fs: introduce CP_TRIMMED_FLAG to avoid unneeded discard")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>