Following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), RTC wake-ups stopped working on Jetson TX2
and Jetson Xavier platforms. The Jetson TX2 uses the max77620 PMIC and
the Jetson Xavier uses max20024 PMIC. Both of these PMICs have the same
max77620 RTC controller.
For the max77620 RTC, the variable 'rtc_irq_from_platform' is defined as
true in the max77686 driver and because of this the IRQ passed to the
max77686 driver for RTC is the PMIC IRQ and not the parent. Hence,
following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), for the max77620 the RTC IRQ within the
PMIC is now getting disabled on entry to suspend and unable to wake the
system up. Fix this by only disabling interrupts on entry to suspend
in the max77686 RTC driver, if the interrupt is the parent interrupt.
Fixes: d8f090dbea ("rtc: max77686: Do not allow interrupt to fire before system resume")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806125431.699339-1-jonathanh@nvidia.com
The rtc-max77686 device shares the main interrupt line with parent MFD
device (max77686 driver). During the system suspend, the parent MFD
device disables this IRQ to prevent an early event happening before
resuming I2C bus controller.
The same should be done by rtc-max77686 driver because otherwise the
interrupt handler max77686_rtc_alarm_irq() will be called before its
resume function (max77686_rtc_resume()). Such issue is not fatal but
disabling shared IRQ by all users ensures correct behavior.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615161455.4420-1-krzk@kernel.org
The MAX77620 doesn't support bulk writes, so make sure the regmap code
breaks bulk writes into multiple single-byte writes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200417170825.2551367-3-thierry.reding@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I was about to simplify the call to i2c_unregister_device() when I
realized that converting to devm_i2c_new_dummy_device() will simplify
the driver a lot. So I took this approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190830133124.21633-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-rtc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-40-swboyd@chromium.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190722172618.4061-3-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In case of error, we return 0.
This is spurious and not consistent with the other functions of the driver.
Commit e115a2bf14 has modified more than what is said in the commit
message. Reverse part of it znd return an error when needed, as it was
previously.
Fixes: e115a2bf14 ("rtc: max77686: stop validating rtc_time in .read_time")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use macro REGMAP_IRQ_REG from regmap.h to initialise the
regmap irq table for max77686 to have better coding style
and improve readability.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.
Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cleanup of entire driver of its dmesg output:
1. Remove printing of the function name, because printing device name is
sufficient. This also makes the dev_err()-like functions more compact
and readable (not need of line break).
2. Lower from info to debug printing of each RTC interrupt (no need to
make noise on each alarm).
3. Remove dev_info() at beginning of probe because a message is already
always printed by either probe failure or from registering the RTC
device as /dev/rtcX.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d9 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC only supports a range of 99 years so instead of using
year 1900 as the base, the year 2000 is used. This means that 1900 to
1999 are unsupported years.
The driver was printing a warning for those values but was returning a
error so for consistency, print an error message instead and don't say
that a year 2000 is assumed, since the year is not set.
Also, it is better to use dev_* log functions instead of pr_* to print
information about the device in the kernel log in a standardized way.
This also allows to remove the local pr_fmt() defined macro.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:
0) The RTC registers layout and addresses are different.
1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
alarm enable while MAX77802 has a separate register for that.
2) The MAX77686 RTCYEAR register valid values range is 0..99 while
for MAX77802 is 0..199.
3) The MAX77686 has a separate I2C address for the RTC registers
while the MAX77802 uses the same I2C address as the PMIC regs.
5) The minimum delay before a RTC update (16 msecs vs 200 usecs).
There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 driver is generic enough that can be used for other
Maxim RTC IP blocks but these might not have the same registers
layout so instead of accessing the registers directly, add a map
to translate offsets to the real registers addresses for each IP.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver has some hard-coded values such as the minimum delay needed
before a RTC update or the mask used for the sec/min/hour/etc registers.
Use a data structure that contains these values and pass as driver data
using the platform device ID table for each device.
This allows to make the driver's ops callbacks more generic so other RTC
that are similar but don't have the same values can also be supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Documentation/timers/timers-howto.txt suggest to use usleep_range()
instead of msleep() for small msec (1ms - 20ms) since msleep() will
often sleep for 20ms for any value in that range.
This is fine in this case since 16ms is the _minimum_ delay required
by max77686 for an RTC update but by using usleep_range() instead of
msleep(), the driver can support other RTC IP blocks with a shorter
minimum delay (i.e: in the range of usecs instead of msecs).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is better to use the ARRAY_SIZE() macro instead of the array length
to avoid bugs if the array is later changed and the length not updated.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function is always returning zero even in case of failures since
the ret value was not propagated to the callers. Fix the error path.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77686 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
max77686_rtc_calculate_wday() is used to calculate the day of the week
to be filled in struct rtc_time but that function only calculates the
number of bits shifted. So the ffs() function can be used to find the
first bit set instead of a special function.
[akpm@linux-foundation.org: add comment clarifying ffs() use]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If devm_rtc_device_register() fails a dev_err() is already reported so
there is no need to do an additional dev_info().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The max77686 mfd driver adds a regmap IRQ chip which creates an IRQ
domain that is used to map the virtual RTC alarm1 interrupt.
The RTC driver assumes that this will always be true since the PMIC IRQ
is a required property according to the max77686 DT binding doc. If an
"interrupts" property is not defined for a max77686 PMIC, then the mfd
probe function will fail and the RTC platform driver will never be
probed.
But even when it is not possible to probe the rtc-max77686 driver
without a regmap IRQ chip, it's better to explicitly check if the IRQ
chip data is not NULL and gracefully fail instead of getting an OOPS.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAX77686 RTC chip has two features called SMPL (Sudden Momentary
Power Loss) and WTSR (Watchdog Timeout and Software Resets). Support
for these features seems to be implemented in the driver but compilation
is disabled using a C pre-processor conditional.
This code has been disabled since the driver was original merged in
commit fca1dd031a ("rtc: max77686: add Maxim 77686 driver").
So, since this code has never been built, let's just remove it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series add support for the Real Time clock present in the Maxim 77802
Power Managment IC. The version number is quite high because it
previously was part of a bigger series [0] that aimed to add support for
all the devices in the max77802 PMIC. But now that the max77802
dependencies were already merged for 3.17, the series were split but I
kept the version numbering.
While working on the max77802 rtc support a lot of feedback was given and
the issues pointed out also apply to a driver for a similar PMIC RTC
(max77686). So patches 01/06 to 05/06 in the series are cleanups for the
max77686 driver and patch 06/06 adds the support for the max77802 RTC.
The series were tested on an Exynos5250 Snow (max77686) and
Exynos5420 Peach Pit (max77802) machines.
This patch (of 6):
The max77686 includes an RTC that keeps power during suspend. It's
convenient to be able to use it as a wakeup source.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By using the generic IRQ support in the Register map API, it
is possible to get rid max77686-irq.c and simplify the code.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a read of the wrong register when checking whether the RTC timer has
reached the alarm time.
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the switch to devm_* functions and the removal of
rtc_device_unregister(), the 'remove' function does not do anything.
Delete it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the following warning:
WARNING: space prohibited before semicolon
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ret' was not initialized to error code before returning. While
at it also remove some redundant code and cleanup.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Laxman dewangan <ldewangan@nvidia.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_rtc_device_register() is device managed and makes cleanup
paths simpler. Also, this patch uses devm_request_threaded_irq().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_info()/dev_emerg() are preferred to pr_info()/pr_emerg().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix indentation of bit definitions to enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_kzalloc() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing module author name to MODULE_AUTHOR macro.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use module_platform_driver() macro which makes the code smaller and
simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a driver to support max77686 rtc. MAX77686 rtc support smpl and wtsr
mode. It has two alarm register which can be used for alarming to wake
system up. This drvier uses regmap to access its register.
[akpm@linux-foundation.org: remove inline, __devinit annotations]
[jg1.han@samsung.com: fix build warnings]
[akpm@linux-foundation.org: simplify code]
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jon Hunter
Krzysztof Kozlowski
Thierry Reding
Wolfram Sang
Stephen Boyd
Christophe JAILLET
Alexandre Belloni
Laxman Dewangan
Krzysztof Kozlowski
Javier Martinez Canillas
Javier Martinez Canillas
Joe Perches
Wolfram Sang
Doug Anderson
Sangjung Woo
Sachin Kamat
Jingoo Han
Jonghwa Lee