My enhancement to store the initial mapping size for later reuse in commit
486df8bc46 ("m68k: Increase initial mapping
to 8 or 16 MiB if possible") broke booting on machines where RAM doesn't
start at address zero.
Use pc-relative addressing to fix this.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
If the size of the first memory chunk is at least 8 or 16 MiB increase the
initial mapping to 8 resp. 16 MiB instead of 4 MiB.
This makes it possible to
1. Map more memory in the first node without running out of space for the
page tables,
2. Boot kernels that don't fit in 4 MiB (e.g. multi_defconfig).
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
- Add support for 8 MiB,
- Store initial mapping size in head.S for later reuse,
- Add comment about large kernels.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fix SCC initialization for Atari as was previously fixed for Mac. It's
probably not practical to share more code but some attempt is made to
align the Mac and Atari variants.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In a multi-platform kernel binary we only need one early console instance.
The difficulty here is that the common early console is started by
early_param(), whereas the MVME16x instance is started later by
config_mvme16x(). That means some interrupt setup must be done earlier.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert] Tag debug_cons_write() with __ref to kill section mismatch warning
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Make the boot console available to more m68k platforms by leveraging
the head.S debug console.
The boot console is enabled by the "earlyprintk" command line argument
which is how most other architectures do this.
This is a change of behaviour for the Mac but does not negatively impact
the common use-case which is not debugging.
This is also a change of behaviour for other platforms because it means
the serial port stays quiet when CONFIG_EARLY_PRINTK is not enabled. This
is also an improvement for the common use-case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert: CONSOLE_DEBUG should depend on CONFIG_FONT_SUPPORT]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Code subject to #ifdef CONSOLE is made more generic, as was apparently
intended by the original author.
Remove console_put_stats() routine. If it should be somehow useful, it
should also be useful on platforms without framebuffer debug logging. The
present implementation is only built #if defined CONFIG_MAC && defined
CONSOLE even though puts() works everywhere.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Allow CONFIG_LOGO to enable/disable the head.S penguin logo as well as the
framebuffer console logo. This should save a few bytes. It also gets rid
of the obscure CONSOLE_PENGUIN macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
For SCC initialization we cannot assume that the control register is in
the correct state to accept a register pointer. So first read from the
control register in order to "sync" up.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Export the bootinfo definitions that are used by bootstrap loaders, and
split them up in generic and platform-specific parts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
struct mac_booter_data is no longer part of the bootinfo API, hence move it
from <asm/bootinfo.h> to <asm/macintosh.h>, dropping all unused fields in
the process.
Also remove the no longer used mac_booter_data pointer from head.S.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since the introduction of init sections (which are located after BSS), the
bootinfo is no longer located right after the BSS, but after all kernel
sections.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The present code does not wait for the SCC to finish resetting itself
before trying to initialise the device. The result is that the SCC
interrupt sources become enabled (if they weren't already). This leads to
an early boot crash (unexpected interrupt) given CONFIG_EARLY_PRINTK. Fix
this by adding a delay. A successful reset disables the interrupt sources.
Also, after the reset for channel A setup, the SCC then gets a second
reset for channel B setup which leaves channel A uninitialised again. Fix
this by performing the reset only once.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: stable@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Revive the old mac_serial_print() routine as mac_early_print(). mac_serial_print() did not function because it did not use the right offsets for its stack arguments. Fix this and make compilation conditional on CONFIG_EARLY_PRINTK instead of the obscure MAC_SERIAL_DEBUG macro.
Give mac_early_print() a new string length parameter to fit the early console API.
Send output to the framebuffer as well as serial ports.
Change the line rate to 38400 baud to match the default for the real (pmac_zilog) serial console.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running a HP300-enabled kernel on non-HP300 hardware, a test in the early
startup code jumps to the wrong label, causing a double bus fault.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. tell modpost that entry point code (that has to be outside
of .init.text for external reasons) is OK to refer to .init.*
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat various m68k files, so they actually look like Linux sources.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Geert Uytterhoeven
Andreas Schwab
Finn Thain
Lucas De Marchi
Sam Ravnborg
Tim Abbott
Al Viro
Roman Zippel
Jörn Engel
Sam Ravnborg
Linus Torvalds