arizona_spk_init uses snd_soc_dapm_new_control which since
commit 37e1df8c95 ("ASoC: dapm: handle probe deferrals") will
occasionally request a probe deferral. Which means we should propagate the
error out of our driver from it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As requirements to bring up audio paths are continuous getting tighter
and the DSP download to most ADSP devices happens over an external bus
it can become an important factor in the path bring up time. As such
sometimes it is a reasonable trade off to download the firmware ahead of
when it will be required and take a small hit on power consumption for
keeping the core powered up.
This "preloading" adds an additional control for each DSP core "DSPx
Preload Switch" that when set to true will power up the DSP core and
download the firmware currently selected in the "DSPx Firmware" control.
Whilst the core is preloaded the current firmware can not be changed and
the CODEC will be kept powered up and SYSCLK held on. Although future
improvements may allow the SYSCLK to be powered down as well because
the hardware only requires SYSCLK whilst the download is actually taking
place, but this is not covered in this series.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SYSCLK is attached to every compressed DAI as this follows the
pattern of attaching clocks to the chips inputs and outputs, however, it is
really the DSP that requires the clock here. As firmware download can be a
significant part of the path startup time for these devices occasionally it
would be desirable to download the firmware in advance of the path being
brought up.
To help facilitate this early firmware loading this patch attaches the
SYSCLK to the DSP preloader widget. This also saves us adding a new route
to SYSCLK every time a new compressed DAI is created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_codec_driver structures that are only passed to
snd_soc_register_codec or memcpy (2nd arg), for which the corresponding
parameters are declared const. Declare as const snd_soc_codec_driver
structures that have these properties.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_codec_driver i@p = { ... };
@ok@
identifier r.i;
expression e1,e2,e3;
position p;
@@
(
snd_soc_register_codec(e1,&i@p,e2,e3)
|
memcpy(e1,&i@p,e2)
)
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_codec_driver i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two clock domains are enabled based on each input and output of the
chip being connected to its respective clock domain. The ASRC however
can bridge the two domains and as such can function as an input/output
to either domain. The hardware also requires that both clocks are
enabled before the ASRC is. Ensure these constraints by linking the
ASRCs to both SYSCLK and ASYNCCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Output 3 is stereo on wm5110 and all inputs/outputs should have a
connection to SYSCLK. This patch adds the missing DAPM route.
Signed-off-by: Ajit Pandey <ajit.pandey@soctronics.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64-bit builds would generate a warning when we passed the core number as
a pointer through the notifier data:
sound/soc/codecs/cs47l24.c:1091:13: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
(void *)i);
Rather than just fix this up with more casting add a data structure that
holds information for the notifier chain. This will make it easier to
add additional information in the future as well.
Fixes: 7baa7e2490 ("ASoC: arizona: Add event notification on voice trigger events")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some situations the voice control firmware will by used
to only provide a trigger notification event. In this case a
compressed stream will not be opened by user-space, as such we
need to provide a virtual output to power on the DSP in this
use-case. This patch adds a virtual output 'DSP Voice Trigger'
that can be used for this, and a switch that lets it be connected
to the core when required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent is for SYSCLK to be tied to all input and output widgets such
that it turns on whenever the chip is in use. It is not tied to the DRC
signal activity detect virtual outputs, whilst in practice this is
unlikely to cause an issue (as an input will likely also be powered up)
best to correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inform the notifier chain if the DSP recognises a voice trigger.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly this adds DAI links for the audio trace, however, it is also
necessary to update the data IRQ handler to check more cores. We have
the handler check every core so it should not be necessary to update
this function if more compressed firmwares are added in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst there is nothing wrong with the error path here it looks a little
bit odd, this patches makes the code a little more idiomatic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was not unregistering the compressed platform in
wm5110_remove(). If the codec is built as a module, this would
lead to a NULL pointer deref if the module was unloaded and then
re-probed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
=d18k
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.5' into asoc-next
ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
# gpg: Signature made Wed 23 Dec 2015 00:42:40 GMT using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
Data is read in blocks of up to one fragment is size from the circular
buffer on the DSP and is re-packed to remove the padding byte that
exists in the DSP memory map.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here support is added for responding to DSP IRQs that are used to
indicate data being available on the DSP. The idea is that we check the
amount of data available upon receipt of an IRQ and on subsequent calls
to the pointer callback we recheck once less than one fragment is
available (to avoid excessive SPI traffic), if there is truely less than
one fragment available we ack the last IRQ and wait for a new one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't want to use a bypassed write in wm5110_clear_pga_volume,
we might disable the DRE whilst the CODEC is powered down. A
normal regmap_write will always go to the hardware (when not on
cache_only) even if the written value matches the cache. As using
a normal write will still achieve the desired behaviour of bring
the cache and hardware in sync, this patch updates the function
to use a normal write, which avoids issues when the CODEC is
powered down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
A couple of call sites were missed when the snd_soc_dapm_mutex_lock
function was added this patch fixes those up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream is created whilst the compressed stream is opened and a
buffer is created when the DSP powers up. It is necessary at a point
once both the DSP has powered up and the the stream has been opened to
connect a stream to a buffer on the DSP. This is done in the trigger
callback as this is after the DSP has been powered and obviously the
stream must be open. Note that whilst the connect is currently trivial
it is expected that this will get more complex when support for multiple
buffers/streams per DSP is added.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow user-space to open a compressed stream, although no data will be
passed yet, as part of this adding the ability to define supported
capabilities per firmware and check these match the stream being opened.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5110 device contains a hardware ANC block, this patch connects up
controls and routing for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier revisions of the wm5110/8280 silicon require a slightly more
complex procedure to enable analogue inputs. This patch adds this into
the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduced by:
commit 8019ff6cfc
("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit d1acd31883
("ASoC: wm5110: Add special DRE on/off handling for the headphone path")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we fail to add some DSPs or fail to add the controls we should call
wm_adsp2_codec_remove for all the cores we have already added. This
patch fixes this up on the wm5102 and wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the best performance the headphone path enable/disable must be
handled specially for the situations of DRE on and DRE off.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifying unstable coefficients for the low/high pass filters can have
a severe impact on the audio. This patchs adds a stability check on the
coefficients written to the low/high pass filter block to prevent this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifying unstable coefficients for the EQ can have a severe impact on
the audio. This patchs adds a stability check on the coefficients
written to the EQ, for this it is necessary to merge the mode control
and the coefficients as some coefficients may only be unstable with a
certain mode setting so it is ideal if these are always updated in sync.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown
Charles Keepax
Richard Fitzgerald
Julia Lawall
Kuninori Morimoto
Ajit Pandey
Nariman Poushin