In certain circumstances the PSL (Power Service Layer, which provides
translation services for CXL hardware) can send an interrupt for a
segment miss that the kernel has already handled. This can happen if
multiple translations for the same segment are queued in the PSL before
the kernel has restarted the first translation.
The CXL driver does not expect this situation and does not check if a
segment had already been handled. This could cause a duplicate segment
table entry which in turn caused a PSL error taking down the card.
This patch fixes the issue by checking for existing entries in the
segment table that match the segment we are trying to insert, so as to
avoid inserting duplicate entries.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the segment table hash calculation from cxl_load_segment()
into find_free_sste() since that is the only place it is actually used.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch simplifies the process of finding a free segment table entry
by disabling the secondary hash. This reduces the number of possible
entries in the segment table for a given address from 16 to 8.
Due to the large segment sizes we use it is extremely unlikely that the
secondary hash would ever have been used in practice, so this should not
have any negative impacts and may even improve performance due to the
reduced number of comparisons that software & hardware need to perform.
This patch clears the SC bit in the hardware's state register
(CXL_PSL_SR_An) to disable the secondary hash in the hardware since we
can no longer fill out entries using it.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUQFBQAAoJENkgDmzRrbjxJRIP/1yCQRElQewxURSmJelyqCdU
0mHYB0R9Mf3tfre1xnofqs2lWeSMc/4ptKHsVR6pupoztSwnz7HsLHfEFvFJh4mj
KsaqYElxkNxTcfyHwLjyJS0/J6tG1tYypXGiimTBS0bvFHL3XZdimVgJ6WvX+gO7
YSaDEX8/EqCERafslS5+gKJlz3drDOnCZCe9y4BDSmsvl2k7bkpSxIn8vsR6jIC0
c5JpUy6QVF+3XA/J932M7yRs+xpqxNoUWiyY3ar9o3CtQAaQB0ZAetSxY6hTfvVc
GlNFzCifdsaQwsl2SVsE2h6tWaRhtMtcGWQuhHThIPyIf8XxhYyBRY2FLo70LMz1
eqtwy6F/Bg/nzUsdee4PZBMeoKHlAEL12RpsEKgfUoLzj16Aqa8ll+Agbglbkw8G
f3d2FwzKAlpY5NwHETC1wYy52PJ3efqksRWuhokmYpxNSbHJS/lsiJOE7272/4Qr
MtXuvRmo22tf34XFd5y7zqWjgZ58eeFOqQWi/K+6ZgpqVOvikjrXXKEuiVdjO0ZD
kTVR/sQKiR+79rzENk80XBhWaMveECNXF1TiZ/3MmURkmEOBRQMxRQ20BX3exvna
AJ/WVA5DcfXZc1yyqknE1NLGrvSBMJENH13x2QPwrqNWAryOOKuF1VKKIwWlDw5j
vtx5nXiJa8YYdxI2TJCN
=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
carma-fpga driver uses device control with custom FSLDMA_EXTERNAL_START
command. Since we wnat to deprecate the device control, move this driver to
use new fsl_dma_external_start() API
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_slave_config() and dmaengine_prep_dma_sg()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace duplicated code in all transports with a single wrapper in
virtio.c.
The only functional change is in virtio_mmio.c: if a buggy device sends
us an interrupt before driver is set, we previously returned IRQ_NONE,
now we return IRQ_HANDLED.
As this must not happen in practice, this does not look like a big deal.
See also commit 3fff0179e3
virtio-pci: do not oops on config change if driver not loaded.
for the original motivation behind the driver check.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: "Igor M. Liplianin" <liplianin@netup.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
If afu_read() returned due to a signal or the AFU file descriptor being
opened non-blocking it would not call finish_wait() before returning,
which could lead to a crash later when something else wakes up the wait
queue.
This patch restructures the wait logic to ensure that the cleanup is
done correctly.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This time around, the cleanup branch contains mostly code removal. A number
of board files for at91, imx and msm have become obsolete because of the
DT conversion and are now ready to be removed. The OMAP platform has
traditionally had its own DMA engine abstraction and as this is being
phased out, a lot of the original code is now unused and can be removed
as well.
S3C24xx can be simplified now that the restart code is a proper device
driver.
Finally, a number of cleanups in shmobile are done to prepare for
the addition of new code in other branches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Af7T
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"This time around, the cleanup branch contains mostly code removal. A
number of board files for at91, imx and msm have become obsolete
because of the DT conversion and are now ready to be removed. The
OMAP platform has traditionally had its own DMA engine abstraction and
as this is being phased out, a lot of the original code is now unused
and can be removed as well.
S3C24xx can be simplified now that the restart code is a proper device
driver.
Finally, a number of cleanups in shmobile are done to prepare for the
addition of new code in other branches"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91: Remove the support for the RSI EWS board
arm: mach-omap2: Convert pr_warning to pr_warn
ARM: OMAP: Remove unused pieces of legacy DMA API
ARM: at91: remove board file for Acme Systems Fox G20
ARM: orion5x: Convert pr_warning to pr_warn
ARM: S3C24XX: remove separate restart code
ARM: EXYNOS: Do not calculate boot address twice
ARM: sunxi: Remove sun4i reboot code from mach directory
ARM: imx: Remove mach-mxt_td60 board file
ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains()
ARM: shmobile: r8a7740: Clean up pm domain table
ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains()
ARM: shmobile: sh7372: Make domain_devices[] static __initdata
ARM: shmobile: mackerel: Make domain_devices[] static __initdata
clocksource: tcb_clksrc: sanitize IRQ request
ARM: at91/tclib: mask interruptions at shutdown and probe
ARM: at91/tclib: move initialization from alloc to probe
ARM: at91/tclib: prefer using of devm_* functions
ARM: clps711x: Switch CLPS711X subarch to use clk and clocksource driver
ARM: shmobile: r8a7791 is now called "R-Car M2-W"
...
Here's the big set of driver patches for char/misc drivers. Nothing
major in here, the shortlog below goes into the details. All have been
in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0ZXYACgkQMUfUDdst+ymiEgCgrKcYUluvdrbjdkhrENk332YN
lcUAoMzgQpbkYhswrDNQet7NtAbFN9LV
=ZPDy
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big set of driver patches for char/misc drivers. Nothing
major in here, the shortlog goes into the details. All have been in
the linux-next tree for a while with no issues"
* tag 'char-misc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (80 commits)
mei: mei_txe_fw_sts can be static
mei: fix kernel-doc warnings
mei: fix KDoc documentation formatting
mei: drop me_client_presentation_num
mei: trivial: fix errors in prints in comments
mei: remove include to pci header from mei module files
mei: push pci cfg structure me hw
mei: remove the reference to pdev from mei_device
mei: move fw_status back to hw ops handlers
mei: get rid of most of the pci dependencies in mei
mei: push all standard settings into mei_device_init
mei: move mei_hbm_hdr function from hbm.h the hbm.c
mei: kill error message for allocation failure
mei: nfc: fix style warning
mei: fix style warning: Missing a blank line after declarations
mei: pg: fix cat and paste error in comments
mei: debugfs: add single buffer indicator
mei: debugfs: adjust print buffer
mei: add hbm and pg state in devstate debugfs print
Drivers: hv: vmbus: Enable interrupt driven flow control
...
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the core of the cxl driver.
It adds support for using cxl cards in the powernv environment only (ie POWER8
bare metal). It allows access to cxl accelerators by userspace using the
/dev/cxl/afuM.N char devices.
The kernel driver has no knowledge of the function implemented by the
accelerator. It provides services to userspace via the /dev/cxl/afuM.N
devices. When a program opens this device and runs the start work IOCTL, the
accelerator will have coherent access to that processes memory using the same
virtual addresses. That process may mmap the device to access any MMIO space
the accelerator provides. Also, reads on the device will allow interrupts to
be received. These services are further documented in a later patch in
Documentation/powerpc/cxl.txt.
Documentation of the cxl hardware architecture and userspace API is provided in
subsequent patches.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the base cxl support that cannot be built as a module. Specifically
it adds the cxl callbacks that are called from the core powerpc mm code which
must always exist irrespective of if the cxl module is loaded or not. This is
similar to how cell works with CONFIG_SPU_BASE.
This adds a cxl_slbia() call (similar to spu_flush_all_slbs()) which checks if
the cxl module is loaded and in use, returning immediately if it is not. If it
is in use it calls into the cxl SLB invalidation code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
me_client_presentation_num field is not used for any
particular purpose now, so it can be safely dropped.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove inclusion of linux/pci.h in mei layer
however we need to include the headers that before
got included implicitly from linux/pci.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device specific configurations are currently only needed by me hw
so we can remove it from txe
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For purpose of adding testing HW we would like
to get rid of pci dependency in generic mei code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fw status retrieval has pci specific implementation
so we push it back to the hw layer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For purpose of adding testing HW we would like
to get rid of pci dependency in generic mei code
This patch provides only straight forward changes
FW status and prob quirks need to be handled separately
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting of hw_ops and device has should be in
mei_device_init.
We add reference to the parent device and remove
pci dependent cfg
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_hbm_hder helper function is only used in hbm.c
so there is no need to define it in a header file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to log memory allocation errors as
this is already done by the memory subsystem.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix style warning:
void function return statements are not generally useful
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix new style warning: Missing a blank line after declarations
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add indication whether the client operates in single
buffer mode
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of many me clients (15 and more) 1K buffer
is not enough for full information print.
Calculate buffer size according to real clients number.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add hbm state, pg enablement and state to devstate file in debugfs
(<debugfs>/mei/devstate)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move PCI_VENDOR_ID_VMWARE from device-specific files to pci_ids.h.
It is useful to always have access to it, especially when accessing
subsystem_vendor_id on emulated devices.
[bhelgaas: keep pci_ids.h sorted and use lower-case hex]
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is untrusted user data from vmci_host_do_send_datagram() so the
VMCI_DG_SIZE() macro can have an integer overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the GenWQE hardware queue was busy, the driver returned simply
-EBUSY. This caused polling by applications which increased the load
on the already busy system. This change implements the possiblity to
sleep on a waitqueue instead when the DDCB queue is busy. The
requestor is woken up when there is free space on the queue again.
The old way to get -EBUSY is still available if the device is openend
with O_NONBLOCKING. The default is now blocking behavior.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a problem we found during debug on PPC64 when
reading HSI status and Retc.
Signed-off-by: Eberhard S. Amann <esa@linux.vnet.ibm.com>
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The checkpatch.pl script got improved. I ran it on the latest GenWQE
sources and fixed what it complained about.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Forgetting to check this, can lead to problems on systems which
do not support SRIOV.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow up patch to the one from Sebastian Ott. There is no need to
change the return code once it fails. And Sebastians version is tested
now and works nicely on our test-system.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Munsie
Linus Torvalds
Vinod Koul
Michael S. Tsirkin
Rasmus Villemoes
Al Viro
Fengguang Wu
Alexander Usyskin
Tomas Winkler
Geert Uytterhoeven
Olof Johansson
Francesco Ruggeri
Dan Carpenter
Frank Haverkamp
Eberhard S. Amann