Add the required registers and commands to erase and write
flash pages / blocks.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
BCH registers are contiguous, not on every byte. Fix the
register definitions.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Making MTD_NAND_OMAP2 depend on ARCH_OMAP2PLUS instead of
oring with ARCH2/3/4.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows each CFI device map to use its own endianness. The
globally defined CFI endianness (CONFIG_MTD_CFI_NOSWAP,
CONFIG_MTD_CFI_BE_BYTE_SWAP or CONFIG_MTD_CFI_LE_BYTE_SWAP) becomes the
default value which can be overridden by a driver for a particular device.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some error paths in mtd_blkdevs were fixed in the following commit:
commit 94735ec404
mtd: mtd_blkdevs: fix error path in blktrans_open
But on these error paths, the block device's `dev->open' count is
already incremented before we check for errors. This meant that, while
the error path was handled correctly on the first time through
blktrans_open(), the device is erroneously considered already open on
the second time through.
This problem can be seen, for instance, when a UBI volume is
simultaneously mounted as a UBIFS partition and read through its
corresponding gluebi mtdblockX device. This results in blktrans_open()
passing its error checks (with `dev->open > 0') without actually having
a handle on the device. Here's a summarized log of the actions and
results with nandsim:
# modprobe nandsim
# modprobe mtdblock
# modprobe gluebi
# modprobe ubifs
# ubiattach /dev/ubi_ctrl -m 0
...
# ubimkvol /dev/ubi0 -N test -s 16MiB
...
# mount -t ubifs ubi0:test /mnt
# ls /dev/mtdblock*
/dev/mtdblock0 /dev/mtdblock1
# cat /dev/mtdblock1 > /dev/null
cat: can't open '/dev/mtdblock4': Device or resource busy
# cat /dev/mtdblock1 > /dev/null
CPU 0 Unable to handle kernel paging request at virtual address
fffffff0, epc == 8031536c, ra == 8031f280
Oops[#1]:
...
Call Trace:
[<8031536c>] ubi_leb_read+0x14/0x164
[<8031f280>] gluebi_read+0xf0/0x148
[<802edba8>] mtdblock_readsect+0x64/0x198
[<802ecfe4>] mtd_blktrans_thread+0x330/0x3f4
[<8005be98>] kthread+0x88/0x90
[<8000bc04>] kernel_thread_helper+0x10/0x18
Cc: stable@kernel.org [3.0+]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Macronix MX30LF1208AA is a 512 Mbit NAND with device code 0xF0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Macronix is produing SLC NAND MX30LF1208AA, so add their manufacturer
code to the manufacturer lists.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we fail to erase a PEB, we free the corresponding erase entry object,
but then re-schedule this object if the error code was something like -EAGAIN.
Obviously, it is a bug to use the object after we have freed it.
Reported-by: Emese Revfy <re.emese@gmail.com>
Cc: stable@kernel.org [v2.6.23+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch fixes usage of dma direction to adopt dma_transfer_direction.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
mtd_device_parse_register() registers the device as a whole if no
partition data is passed so there is no reason to call
mtd_device_register() after that.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make this work again.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function 'gpmi_nfc_init':
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: At top level:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:15: error: expected declaration specifiers or '...' before string constant
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: data definition has no type or storage class
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
and some more...
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit 9d7948c500 (mtd: ndfc: use
ofpart through generic parsing) we dereference a non pointer type
causing the following compiler error:
drivers/mtd/nand/ndfc.c: In function 'ndfc_chip_init':
drivers/mtd/nand/ndfc.c:191: error: invalid type argument of '->' (have 'struct mtd_part_parser_data')
Fix that.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Under some cases, when scrubbing the PEB if we did not get the lock on
the PEB it fails to scrub. Add that PEB again to the scrub list
Artem: minor amendments.
Cc: stable@kernel.org [2.6.31+]
Signed-off-by: Bhavesh Parekh <bparekh@nvidia.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MTD_PARTITIONS got killed in commit 6a8a98b22b. This means that since
v3.0 this Kconfig symbol doesn't exist anymore. Apparently selecting
a non-existant symbol is a nop. Drop that select.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
module.h was previously implicitly included through mtd/mtd.h.
Fixes the following build failure after the module.h cleanup:
CC drivers/mtd/maps/bcm963xx-flash.o
drivers/mtd/maps/bcm963xx-flash.c: In function 'bcm963xx_probe':
drivers/mtd/maps/bcm963xx-flash.c:208:29: error: 'THIS_MODULE' undeclared (first use in this function)
[...]
drivers/mtd/maps/bcm963xx-flash.c:276:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/mtd/maps/bcm963xx-flash.c:276:15: warning: function declaration isn't a prototype
make[7]: *** [drivers/mtd/maps/bcm963xx-flash.o] Error 1
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
We are cleaning up the implicit presence of module.h that these
drivers are taking advantage of. Fix them in advance of the
cleanup operation.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two common macros will be no longer present everywhere.
Call out the include needs of them explicitly where required.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The tests may erase mtd devices, so annotate them as suggested per
coding style and add a paragraph to the help text as well.
Artem: amended the help test a bit.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
mtd tests may erase the mtd device, so force the user to specify which
mtd device to test by using the module parameter. Disable the default
(using mtd0) since this may destroy a vital part of the flash if the
module is inserted accidently or carelessly.
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@intel.com>
Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.
And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 2 functions add_mtd_partitions and del_mtd_partitions were renamed to
mtd_device_register and mtd_device_unregister.
Signed-of-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Our `ops' information was converted to a local variable recently, and
apparently, old code relied on the fact that the global version was
often left in a valid mode. We can't make this assumption on local
structs, and we shouldn't be relying on a previous state anyway.
Instead, we initialize mode to 0 for don't-care situations (i.e., the
operation does not use OOB anyway) and MTD_OPS_PLACE_OOB when we want to
place OOB data.
This fixes a bug with nand_default_block_markbad(), where we catch on
the BUG() call in nand_fill_oob():
Kernel bug detected[#1]:
...
Call Trace:
[<80307350>] nand_fill_oob.clone.5+0xa4/0x15c
[<803075d8>] nand_do_write_oob+0x1d0/0x260
[<803077c4>] nand_default_block_markbad+0x15c/0x1a8
[<802e8c2c>] part_block_markbad+0x80/0x98
[<802ebc74>] mtd_ioctl+0x6d8/0xbd0
[<802ec1a4>] mtd_unlocked_ioctl+0x38/0x5c
[<800d9c60>] do_vfs_ioctl+0xa4/0x6e4
[<800da2e4>] sys_ioctl+0x44/0xa0
[<8001381c>] stack_done+0x20/0x40
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
parse_mtd_partitions takes a list of partition types; if the driver
isn't loaded, it attempts to load it, and then it grabs the partition
parser. For redboot, the module name is "redboot.ko", while the parser
name is "RedBoot". Since modprobe is case-sensitive, attempting to
modprobe "RedBoot" will never work. I suspect the embedded systems that
make use of redboot just always manually loaded redboot prior to loading
their specific nand chip drivers (or statically compiled it in).
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org
On some platforms such as P3060QDS, has multiple spi flashes, but they are
not available at same time, so if their status is 'disabled', which is set
by u-boot, will not be probed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This driver has been broken through all of git history and
cannot even be built. Better mark it as broken. Next stop is
removing from the tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
- no flash writes/erases are implemented
- ECC fixes are not implemented
- powerdown is not implemented
- IPL handling is not yet done
On the brighter side, the chip reading does work.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add support for EON spi flash EN25Q32B, which is not listed in id table,
need to add it in the id table to support the EON flash.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This is similar to what the nbd driver does, among others.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
It is not used outside this driver so no need to make the symbol global.
Also make r852_suspend and r852_resume static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For NFC v1, the unlock end block address was 0x4000, which would only
unlock the first 32 blocks of the NAND flash. Change that value to
0xffff to unlock all available blocks, as is done for NFC v21 as well.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
A portion of the `check_pattern()' function is basically a `memcmp()'.
Since it's possible for `memcmp()' to be optimized for a particular
architecture, we should use it instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
In rare cases, we are given an unaligned parameter `from' in
`nand_do_read_ops()'. In such cases, we use the page cache
(chip->buffers->databuf) as an intermediate buffer before dumping to the
client buffer. However, there are also cases where this buffer is not
cleanly reusable. In those cases, we need to make sure that we
explicitly invalidate the cache.
This patch prevents accidental reusage of the page cache, and for me,
this solves some problems I come across when reading a corrupted BBT
from flash (NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Note: the rare "unaligned" case is a result of the extra BBT pattern +
version located in the data area instead of OOB.
Also, this patch disables caching on raw reads, since we are reading
without error correction. This is, obviously, prone to errors and should
not be cached.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Updates to our default function for creating bad block patterns have
broken the "no OOB" feature. The NAND_BBT_NO_OOB option should not be
set while scanning for bad blocks, but we've been passing all BBT
options from nand_chip.bbt_options to the bad block scan. This causes us
to hit the:
BUG_ON(bd->options & NAND_BBT_NO_OOB);
in create_bbt() when we scan the flash for bad blocks.
Thus, while it can be legal to set NAND_BBT_NO_OOB in a custom badblock
pattern descriptor (presumably with NAND_BBT_CREATE disabled?), we
should not pass it through in our default function.
Also, to help clarify and emphasize that the function creates bad block
patterns only (not, for example, table descriptors for locating
flash-based BBT), I renamed `nand_create_default_bbt_descr' to
`nand_create_badblock_pattern'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Because there are so many cases of checking, writing, and re-writing of
the bad block table(s), we might as well wait until the we've settled on
a valid, clean copy of the table. This also prevents us from falsely
incrementing the table version. For example, we may have the following:
Primary table, with version 0x02
Mirror table, with version 0x01
Primary table has uncorrectable ECC errors
If we don't have this fix applied, then we will:
Choose to read the primary table (higher version)
Set mirror table version to 0x02
Read back primary table
Invalidate table because of ECC errors
Retry readback operation with mirror table, now version 0x02
Mirrored table reads cleanly
Writeback BBT to primary table location (with "version 0x02")
However, the mirrored table shouldn't have a new version number.
Instead, we actually want:
Choose to read the primary table (higher version)
Read back primary table
Invalidate table because of ECC errors
Retry readback with mirror table (version 0x01)
Mirrored table reads cleanly
Set both tables to version 0x01
Writeback BBT to primary table location (version 0x01)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Now that `read_bbt()' returns ECC error codes properly, we handle those
codes when checking the integrity of our flash-based BBT.
The modifications can be described by this new policy:
*) On any uncorrected ECC error, we invalidate the corresponding table
and retry our version-checking integrity logic.
*) On corrected bitflips, we mark both tables for re-writing to flash
(a.k.a. scrubbing).
Current integrity checks (i.e., comparing version numbers, etc.) should
take care of all the cases that result in rescanning the device for bad
blocks or falling back to the BBT as found in the mirror descriptor.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Instead of just printing a warning when encountering ECC errors, we
should return a proper error status and print a more informative
warning. Later, we will handle these error messages in the upper layers
of the BBT scan.
Note that this patch makes our check for ECC error codes a little bit
more restrictive, leaving all unrecognized errors to the generic "else"
clause. This shouldn't cause problems and could even be a benefit.
This code is based on some findings reported by Matthieu Castet.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This is a second step in restructuring `check_create()'. When we don't
rely on goto statements for our main functionality, the code will become
a little easier to manipulate.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We will begin restructuring the code for check_create so that we can
make some important changes. For now, we should just begin to get rid of
some goto statements to make things cleaner. This is the first step of a
few, which are separated to make them easier to follow.
This step should just be a code refactor.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Remove some extra spaces
Consistently use '0x' prefix for bitfield-like constants
Spelling: "aplies" -> "applies"
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
`writeops' is unnecessary in the function `nand_update_bbt()'
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
There are a few reasons not to ignore ECC errors here.
First, mtd->read_oob is being called in raw mode, so there should be no
error correction in the first place.
Second, if we change this such that there *is* error correction in this
function, then we will want to pass the error message upward.
In fact, the code I introduced to "ignore ECC errors" would have been
better if it had just placed this test down in `scan_block_full()' in
the first place. We would like to ignore ECC errors when we are simply
checking for bad block markers (e.g., factory marked), but we may not
want to ignore ECC errors when scanning OOB for a flash-based BBT
pattern (in `scan_read_raw()'; note that the return codes from
`scan_read_raw()' are not actually handled yet).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
A few pieces of code are unnecessarily duplicated. For easier
maintenance, we should fix this.
This should have no functional effect.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The integrator flash has been deleted, even from the Makefile.
Drop the Kconfig entry as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The ecctype and eccsize fields have been obsolete for a while. Since they
don't have any users, we can kill them and leave padding in their place
for now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The nand_chip.ops field is a struct that is passed around globally with
no particular reason. Every time it is used, it could just as easily be
replaced with a local struct that is updated on each operation. So make
it local.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Implement a new ioctl for writing both page data and OOB to flash at the
same time. This ioctl is intended to be a generic interface that can
replace other ioctls (MEMWRITEOOB and MEMWRITEOOB64) and cover the
functionality of several other old ones, e.g., MEMWRITE can:
* write autoplaced OOB instead of using ECCGETLAYOUT (deprecated) and
working around the reserved areas
* write raw (no ECC) OOB instead of using MTDFILEMODE to set the
per-file-descriptor MTD_FILE_MODE_RAW
* write raw (no ECC) data instead of using MTDFILEMODE
(MTD_FILE_MODE_RAW) and using standard character device "write"
This ioctl is especially useful for MLC NAND, which cannot be written
twice (i.e., we cannot successfully write the page data and OOB in two
separate operations). Instead, MEMWRITE can write both in a single
operation.
Note that this ioctl is not affected by the MTD file mode (i.e.,
MTD_FILE_MODE_RAW vs. MTD_FILE_MODE_NORMAL), since it receives its write
mode as an input parameter.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes hold their state only for the life of their file descriptor,
and they overlap functionality with the MTD_OPS_* modes. Particularly,
MTD_MODE_RAW and MTD_OPS_RAW cover the same function: to provide raw
(i.e., without ECC) access to the flash. In fact, although it may not be
clear, MTD_MODE_RAW implied that operations should enable the
MTD_OPS_RAW mode.
Thus, we should be specific on what each mode means. This is a start,
where MTD_FILE_MODE_* actually represents a "file mode," not necessarily
a true global MTD mode.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We will want to use the MTD_OOB_{PLACE,AUTO,RAW} modes in user-space
applications through the introduction of new ioctls, so we should make
this enum a shared type.
This enum is now anonymous.
Artem: tweaked the patch.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nanddump -n' and the MEMREADOOB[64] ioctls on
hardware that performs error correction when reading only OOB data. A
driver for such hardware needs to know when we're doing a RAW vs. a
normal write, but mtd_do_read_oob does not pass such information to the
lower layers (e.g., NAND). We should pass MTD_OOB_RAW or MTD_OOB_PLACE
based on the MTD file mode.
For now, most drivers can get away with just setting:
chip->ecc.read_oob_raw = chip->ecc.read_oob
This is done by default; but for systems that behave as described above,
you must supply your own replacement function.
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nandwrite -n -o' and the MEMWRITEOOB[64] ioctls
on hardware that writes ECC when writing OOB. The problem arises as
follows: `nandwrite -n' can write page data to flash without applying
ECC, but when used with the `-o' option, ECC is applied (incorrectly),
contrary to the `--noecc' option.
I found that this is the case because my hardware computes and writes
ECC data to flash upon either OOB write or page write. Thus, to support
a proper "no ECC" write, my driver must know when we're performing a raw
OOB write vs. a normal ECC OOB write. However, MTD does not pass any raw
mode information to the write_oob functions. This patch addresses the
problems by:
1) Passing MTD_OOB_RAW down to lower layers, instead of just defaulting
to MTD_OOB_PLACE
2) Handling MTD_OOB_RAW within the NAND layer's `nand_do_write_oob'
3) Adding a new (replaceable) function pointer in struct ecc_ctrl; this
function should support writing OOB without ECC data. Current
hardware often can use the same OOB write function when writing
either with or without ECC
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These files contain the common code for the GPMI-NAND driver.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
add the GPMI-NAND driver in the relevant Kconfig and Makefile in the MTD.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The code has the check for parts but it called after kmemdup,
kmemdup(parts, sizeof(*parts) * nr_parts,...)
if (!parts)
return -ENOMEM
In fact, we need check parts before safely using it.
and we also need check the real_parts to make sure kmemdup
allocation sucessfully.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Previous generations of MTDs all used OOB sizes that were powers of 2,
(e.g., 64, 128). However, newer generations of flash, especially NAND,
use irregular OOB sizes that are not powers of 2 (e.g., 218, 224, 448).
This means we cannot use masks like "mtd->oobsize - 1" to assume that we
will get a proper bitmask for OOB operations.
These masks are really only intended to hide the "page" portion of the
offset, leaving any OOB offset intact, so a masking with the writesize
(which *is* always a power of 2) is valid and makes more sense.
This has been tested for read/write of NAND devices (nanddump/nandwrite)
using nandsim and actual NAND flash.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This has already been tested with Samsung NAND: K9LAG08U0M
on MX53EVK board, ubi/ubifs has already been tested OK too.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Convert error handling code to use gotos. At the same time, this adds
calls to kfree and iounmap in a few cases where they were overlooked.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
clk_get() return a pointer to the struct clk or an ERR_PTR().
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
use MTD_NAND_OMAP2 also for OMAP4 arch.
testes with omap4430
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Some messages that were tied to CONFIG_MTD_DEBUG_VERBOSE can now simply
be enabled using dynamic debugging features, if necessary. There's no
need for special debugging functions here.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We don't need a custom DEBUG() macro here. Just use the built-in kernel
code with dynamic debugging features.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.
(See Documentation/dynamic-debug-howto.txt)
Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This is a cleanup of some punctuation, indentation, and capitalization
on the lines affected affected by the last patch.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Instead of directly calling printk, it's simpler to use the built-in
pr_* functions. This shortens code and allows easy customization through
the definition of a pr_fmt() macro (not used currently). Ideally, we
could implement much of this with dev_* functions, but the MTD subsystem
does not necessarily register all its master `mtd_info.dev` device, so
we cannot use dev_* consistently. See:
http://lists.infradead.org/pipermail/linux-mtd/2011-July/036950.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Soon we will change many printk statements into pr_* statements, i.e.,
'printk(KERN_INFO, ...)' becomes 'pr_info(...)'. However, this means that
KERN_DEBUG messages will become pr_debug() statements and therefore will
not be activated by default - they must be enabled using dynamic debug.
So, for important DEBUG messages, we will simply upgrade these to INFO
so that they appear by default.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
It adds device tree probe support for mtd_dataflash driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Current pxa3xx_nand controller has two chip select which
both be workable. This patch enable this feature.
Update platform driver to support this feature.
Another notice should be taken that:
When you want to use this feature, you should not enable the
keep configuration feature, for two chip select could be
attached with different nand chip. The different page size
and timing requirement make the keep configuration impossible.
Signed-off-by: Lei Wen <leiwen@marvell.com>
This patch add protection on the suspend&resume path to prevent
some unexpected behavior, like interrupt occur at the very second
of resume back and it don't follow normal command path, which lead
to bug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
For PIO NAND access functions, we use the features of the SMC:
- no need to take into account the NAND bus width: SMC will deal with this
- use of an IO memcpy on the NAND chip-select space is able to generate
proper SMC behavior.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
The global data fsl_lbc_ctrl_dev->nand don't have to be freed in
fsl_elbc_chip_remove(). The right place to do that is in fsl_elbc_nand_remove()
if elbc_fcm_ctrl->counter is zero.
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
there is a bug in nand_flash_detect_onfi, busw need to be passed
by pointer to return it.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
This comment was unclear regarding which NAND functions do and do not
support ECC on the spare area. This update should reflect the current
status of the NAND system but can be updated if changes are made in
the standard functions.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
read_oob may now return ECC error codes. If the code is -EUCLEAN, then
we can safely ignore the error as a corrected bitflip.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Now that nand_do_readoob() may return -EUCLEAN or -EBADMSG on ECC errors,
we need to handle the return value specially in some cases.
When scanning for simple bad block markers, reacting to an ECC error is
not very useful, as we assume that the relevant markers are still
non-0xFF for true bad blocks.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
While the standard NAND OOB functions do not do ECC on the spare area,
it is possible for a driver to supply its own OOB ECC functions (e.g., HW
ECC). nand_do_read_oob should act like nand_do_read_ops in checking the
ECC stats and returning -EBADMSG or -EUCLEAN on uncorrectable errors or
correctable bitflips, respectively. These error codes could be used in
flash-based BBT code or in YAFFS, for example.
Doing this, however, messes with the behavior of mtd_do_readoob. Now,
mtd_do_readoob should check whether we had -EUCLEAN or -EBADMSG errors
and discard those as "non-fatal" so that the ioctls can still succeed
with (possibly uncorrected) data.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
As ofpart now uses a standard mtd partitions parser interface, make it
buildable as a separate module. Also provide MODULE_DESCRIPTION and
MODULE_AUTHOR for this module.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
mtd_device_register() is a limited version of mtd_device_parse_register.
Replace it with macro calling mtd_device_parse_register().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There is no need to pollute public header with a definition private
to mtdpart.c. Move it from mtd/partitions.h to mtdpart.c
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There is no need to export parse_mtd_partitions() now , as it's fully handled
by registration functions. So move the definition to private header and
remove respective EXPORT_SYMBOL_GPL.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
EDB7312 isn't supported by mainline kernel, so drop it now.
If the board support will ever be submitted to mainline,
one can revert this commit.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
EDB7312 isn't supported by mainline kernel, this driver wasn't working
before recent fixes, the same functionality can be achieved via physmap,
so drop it now. If the board support will ever be submitted to mainline,
one either can revert this commit, or use physmap mtd map driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There are two different 4KiB pagesize chips
KFM4G16Q4M series have NOP 4 with version ID 0x0131
But KFM4G16Q5M has NOP 1 with versoin ID 0x013e
Note that Q5M means that it has NOP 1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Move parse_obsolete_partitions() to ofpart.c and register it as an
ofoldpart partitions parser.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
All users have been converted to call of_mtd_parse_partitions through
parse_mtd_partitions() multiplexer. Drop obsolete API.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Prepare to convert of_mtd_parse_partitions() to usual partitions parser:
1) Register ofpart parser
2) Internally don't use passed device for error printing
3) Add device_node to mtd_part_parser_data struct
4) Move of_mtd_parse_partitions from __devinit to common text section
5) add ofpart to the default list of partition parsers
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Encapsulate last MTD partition parser argument into a separate
structure. Currently it holds only 'origin' field for RedBoot parser,
but will be extended in future to contain at least device_node for OF
devices.
Amended commentary to make kerneldoc happy
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
In nand_do_write_ops() code it is possible for a caller to provide
ops.oobbuf populated and ops.mode == MTD_OOB_AUTO, which currently
means that the chip->oob_poi buffer isn't initialised to all 0xFF.
The nand_fill_oob() method then carries out the task of copying
the provided OOB data to oob_poi, but with MTD_OOB_AUTO it skips
areas marked as unavailable by the layout struct, including the
bad block marker bytes.
An example of this causing issues is when the last OOB data read
was from the start of a bad block where the markers are not 0xFF,
and the caller wishes to write new OOB data at the beginning of
another block. In this scenario the caller would provide OOB data,
but nand_fill_oob() would skip the bad block marker bytes in
oob_poi before copying the OOB data provided by the caller.
This means that when the OOB data is written back to NAND,
the block is inadvertently marked as bad without the caller knowing.
This has been witnessed when using YAFFS2 where tags are stored
in the OOB.
To avoid this oob_poi is always initialised to 0xFF to make sure
no left over data is inadvertently written back to the OOB area.
Credits to Brian Norris <computersforpeace@gmail.com> for fixing this
patch.
Signed-off-by: Adam Thomson <adam.thomson@alcatel-lucent.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: stable@kernel.org [2.6.20+]
onenand_release() will call mtd_device_unregister(), thus remove the redundant
mtd_device_unregister() call before onenand_release().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Axel Lin <axel.lin@gmail.com>: fixed build error.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Axel Lin <axel.lin@gmail.com>: fixed build breakage
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Robert Jarzmik
Shubhrajyoti D
Aaron Sierra
Brian Norris
Linus Torvalds
Arnd Bergmann
Greg Kroah-Hartman
Artem Bityutskiy
Al Viro
Shawn Guo
Ilya Yanok
Manuel Lauss
Jonathan Cameron
Wolfram Sang
Tony Breeds
Bhavesh Parekh
Jean-Christophe PLAGNIOL-VILLARD
Paul Bolle
Jonas Gorski
Miklos Szeredi
Paul Gortmaker
John Crispin
Andres Salomon
Shaohui Xie
Dan McGee
Axel Lin
Mikhail Kshevetskiy
Wolfram Stering
Linus Walleij
Huang Shijie
Jason Liu
Julia Lawall
Michael Hench
Jonghwan Choi
Jan Weitzel
Lei Wen
Mike Hench
Nicolas Ferre
Liu Shuo
Matthieu CASTET
Dmitry Eremin-Solenikov
Kyungmin Park
THOMSON, Adam (Adam)