The commit [49fb18972581: ALSA: hda - Set stream_pm ops automatically
by generic parser] resulted in regressions on some Realtek and VIA
codecs because these drivers set patch_ops after calling the generic
parser, thus stream_pm got cleared to NULL again. I haven't noticed
since I tested with IDT codec.
Restore (partial revert) the stream_pm ops for them to fix the
regression.
Fixes: 49fb189725 ('ALSA: hda - Set stream_pm ops automatically by generic parser')
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When headphone mic boost is above zero, some 10 - 20 second delay
might occur before the headphone mic is operational.
Therefore disable the headphone mic boost control (recording gain is
sufficient even without it).
(Note: this patch is not about the headset mic, it's about the less
common mic-in only mode.)
BugLink: https://bugs.launchpad.net/bugs/1454235
Suggested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report that 4.1-rc causes noises on a Dell
laptop. Similar like Realtek codec, this seems also triggered by the
recent power_save_node feature. As this kind of issue is quite hard
to debug without actual hardware, disable the power_save_node flag for
this codec as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new AMD controller [1002:aac8] seems to need the quirk for other AMD
NS HDMI stuff, otherwise it gives noisy sounds.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99021
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows user to test power_save_node feature via sysfs or patch
firmware even on the codecs that don't specify it. It'll also save a
few lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7290006d8c.
Through the regression report, it was revealed that the
tpacpi_led_set() call to thinkpad_acpi helper doesn't only toggle the
mute LED but actually mutes the sound. This is contradiction to the
expectation, and rather confuses user.
According to Henrique, it's not trivial to judge which TP model
behaves "LED-only" and which model does whatever more intrusive, as
Lenovo's implementations vary model by model. So, from the safety
reason, we should revert the patch for now.
Reported-by: Martin Steigerwald <martin@lichtvoll.de>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got reports that ALC3226 (a Dell variant of ALC292) gives click
noises at transition from D3 to D0 when the widget power-saving is
enabled. Further debugging session showed that avoiding it isn't
trivial, unfortunately, since paths are basically activated
dynamically while the pins have been already enabled.
This patch disables the widget power-saving for such codecs.
Reported-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget (node) power-saves restore the widget states at each
transition from D3 to D0 on each node. This was added in the commit
[d545a57c5f84:ALSA: hda - Sync node attributes at resume from widget
power saving]. However, the test was rater false-positive; this
wasn't needed for any codecs.
Since the resync may take significant number of additional verbs to be
executed, it's better to reduce it. Let's disable it for now again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo ThinkPad L450 requires the ALC292_FIXUP_TPT440_DOCK fix in
order to get sound output on the docking stations audio port.
This patch was tested using a ThinkPad L450 (20DSS00B00) using kernel
4.0.3 and a ThinkPad Pro Dock.
Signed-off-by: Ansgar Hegerfeld <linux@hegerfeld.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for Conexant HD Audio codecs
CX20721, CX20722, CX20723 and CX20724.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1454656
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC662 does not need any special verbs to change the jack functionality,
and enables mic in through the headphone jack mode by changing the
direction of the headphone pin node.
BugLink: https://bugs.launchpad.net/bugs/1454235
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This enables the headset microphone on Dell Inspiron 5548,
or at least some variants of it.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1452175
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook
T731. Otherwise the headphone is always muted.
Reported-and-tested-by: Christian Weber <we_chris@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Looks like audigy emu10k2 (probably emu10k1 - sb live too) support two
modes for DMA. Second mode is useful for 64 bit os with more then 2 GB
of ram (fixes problems with big soundfont loading)
1) 32MB from 2 GB address space using 8192 pages (used now as default)
2) 16MB from 4 GB address space using 4096 pages
Mode is set using HCFG_EXPANDED_MEM flag in HCFG register.
Also format of emu10k2 page table is then different.
Signed-off-by: Peter Zubaj <pzubaj@marticonet.sk>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models provide too long string for the shortname that has 32bytes
including the terminator, and it results in a non-terminated string
exposed to the user-space. This isn't too critical, though, as the
string is stopped at the succeeding longname string.
This patch fixes such entries by dropping "SB" prefix (it's enough to
fit within 32 bytes, so far). Meanwhile, it also changes strcpy()
with strlcpy() to make sure that this kind of problem won't happen in
future, too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the missing flag to enable "Mute-LED Mode" mixer enum
ctl for Thinkpads that have also the software mute-LED control.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED mode control has the fixed on/off states that are
supposed to remain on/off regardless of the master switch. However,
this doesn't work actually because the vmaster hook is called in the
vmaster code itself.
This patch fixes it by calling the hook indirectly after checking the
mute LED mode.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell XPS13 produces a click noise at boot up, and Gabriele spotted out
that it's triggered by the initial pin control of the mic (NID 0x19).
This has to be set to Hi-Z Vref while the driver initializes to Vref
80% as a normal mic.
This patch fixes the generic parser code not to override the target
vref if it has been already set by the driver, and adds a proper
initialization of the target vref for this pin in the Realtek driver
side.
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Switch default pcbeep path to Line in path.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ALC256 does not have a mixer nid at 0x0b, and there's no
loopback path (the output pins are directly connected to the DACs).
This commit fixes an "num_steps = 0 for NID=0xb (ctl = Beep Playback Volume)"
error (and as a result, problems with amixer/alsamixer).
If there's pcbeep functionality, it certainly isn't controlled by setting an
amp on 0x0b, so disable beep functionality (at least for now).
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1446517
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only Intel Haswell and Broadwell have a separate HD-A controller (PCI device 3)
for display audio, which needs to get 24MHz HD-A link BCLK from the variable
display core clock through vendor specific registers EM4 & EM5. Other platforms
(Baytrail, Braswell and Skylake) don't have this feature.
So this patch checks the PCI device ID of the controller in haswell_set_bclk()
and only sync BCLK for HSW and BDW.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Muting the headphone output pin right before the codec suspension
prevents pop noises when headphones are plugged in (except for a
barely audible click noise).
This solution allows to truly save some power when headphones are
plugged in unlike the previous solution (033b0a7ca9c:
"ALSA: hda - Pop noises fix for XPS13 9333")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function is a bit unusual because it accepts negative values as
"conn_len". It's theoretically possible for both "cache_len" and
"conn_len" to be -ENOSPC and in that case we would oops trying to run
memcmp() on the uninitialized "list" pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [a551d91473e5: ALSA: hda - Use regmap for command verb
caches, too] introduced a regression due to a typo in the conversion;
the IEC958 status bits of slave digital devices aren't updated
correctly. This patch corrects it.
Fixes: a551d91473 ('ALSA: hda - Use regmap for command verb caches, too')
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DEVICE_ALI previously would jump to port_inited after calling
pci_iomap(), bypassing the check for bmaddr being NULL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because AZX_DCAPS_PM_RUNTIME is always defined as non-zero, the
initial part of the expression can be skipped.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Thinkpad T450 requires the ALC292_FIXUP_TPT440_DOCK as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T450 (20BVCTO1WW) using kernel 4.0-rc7 in
conjunction with a ThinkPad Ultradock.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The optical ports on the E-mu 1010 (and dock) can be configured
for ADAT- or S/PDIF-mode, which is currently hardcoded to ADAT.
Add two mixer elements to expose this setting.
Tested on an E-mu 1010 PCIe with connected Micro Dock.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the dock on an E-mu 1010 card is disconnected, all outputs get
muted by the hardware. Add logic to detect a disconnect and unmute.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model uses the same dock port as the previous generation.
Signed-off-by: Yves-Alexis Perez <corsac@debian.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read
acquire the emu_lock before accessing the FPGA. The function used
to access the FPGA (snd_emu1010_fpga_read) also tries to take
the emu_lock which causes a deadlock.
Remove the outer locking in the proc-functions (guarding only the
already safe fpga read) to prevent this deadlock.
[removed superfluous flags variables too -- tiwai]
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A comma was used instead of a semicolon, which may lead to a build
error.
Fixes: cffd396681 ('ALSA: hda/realtek - Fix the regression by widget power-saving')
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the case for Realtek, VIA codec driver needs this ops as
well for making the widget power-save working.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While enabling the widget power-saving for ALC269 & co, the important
setup was forgotten -- stream_pm ops. Without this setup, the paths
for PCM won't be powered up at all.
Also, the power_filter callbacks used in ALC269 & co need to chain to
the default snd_hda_gen_path_power_filter().
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the generic parser sets codec->power_filter when
power_save_node flag is set. But this overrides the existing filter
that has been already set by the codec driver, thus it looses some
features. Instead, set the default power_filter only when it's not
set yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the check of power_save_node flag at the beginning of the function
so that it skips the rest if the flag isn't set. In this way, we can
call this function safely no matter whether the widget power-saving is
really used or not.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the widget power-saving is enabled, the first automute hook
invocation checks through the whole pins and it also tries to
synchronize the power state. However, this results in a wrong state
because it calls unconditionally snd_hda_jack_detect_state().
This patch adds a check of jack detectability before the actual jack
detection call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new widget power-saving tries to apply the power change no matter
whether the node has a power cap or not. It's bad (although most of
codecs chip just ignore it). Check the capability properly
beforehand.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS version of Fujitsu Lifebook T731 seems to set up the
headphone pin (0x21) without the assoc number 0x0f while it's set only
to the output on the docking port (0x1a). With the recent commit
[03ad6a8c93b6: ALSA: hda - Fix "PCM" name being used on one DAC when
there are two DACs], this resulted in the weird mixer element
mapping where the headphone on the laptop is assigned as a shared
volume with the speaker and the docking port is assigned as an
individual headphone.
This patch improves the situation by correcting the headphone pin
config to the more appropriate value.
Reported-and-tested-by: Taylor Smock <smocktaylor@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell create new platform with ALC288 codec.
This patch will enable headset mode for Dino platform.
[slight code refactoring and compile fix by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang
Takashi Iwai
David Henningsson
Ansgar Hegerfeld
Peter Zubaj
Hui Wang
Mengdong Lin
Gabriele Mazzotta
Dan Carpenter
Scott Wood
Jo-Philipp Wich
Michael Gernoth
Yves-Alexis Perez