Synchronize with version 0.46 of the Intel PIIX/ICH driver:
- carry over Alan's and my own fixes in the tuneproc() method and my cleanups
both there and in the ratemask() method;
- SLC90E66 only supports MW DMA modes 1/2 and SW DMA mode 2 (just like Intel
chips), so don't claim support for other MW/SW DMA modes;
- don't check dor non-NULL drive->id in the ide_dma_check() method -- this is
assumed to be true in all other drivers;
- do some coding/formatting cleanups while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix/cleanup the driver's tuneproc() and ratemask() methods:
- PPE, IE, and TIME bits need to be cleared beforehand for the slave drive as
well as master (Alan probably just forgot about it);
- this driver only supports PIO modes up to 4, so must pass the correct limit
to ide_get_best_pio_mode();
- use min_t() macro instead of min();
- simplify slave vs master drive evaluation;
- do come coding and formatting cleanups...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to the datasheet, Intel 82371MX (MPIIX) actually has only a
single IDE channel mapped to the primary or secondary ports depending on
the value of the bit 14 of the IDETIM register at PCI config. offset 0x6C
(the register at 0x6F which the driver refers to. doesn't exist). So,
disguise the controller as dual channel and set enablebits masks/values
such that only either primary or secondary channel is detected enabled.
Also, preclude the IDE probing code from reading PCI BARs, this controller
just doesn't have them (it's not the separate PCI function like the other
PCI controllers), it only decodes the legacy addresses.
[ Alan sayeth " MPIIX does not work with or without the change. It needs its
own different driver and not to use setup-pci. Huge job and since it works
well with libata who cares. Ditto the early PIIX chip." ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix minor coding mistake in the HPT36x PCI clock detection code noticed by
Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing
'break' statements. This, however, most probably never mattered -- in fact, I
was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes
didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e.
supported only 33 MHz PCI.
Note that in the original driver there was another bug: 25 and 40 MHz cases
were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks,
a lower clock count just *cannot* correspond to a higher frequency, i. e. it
should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Finally, rework the driver init. code to correctly handle all the chip
variants HighPoint has created so far. This should cure the rest of the
timing issues in the driver (especially, on 66 MHz PCI) caused by the
HighPoint's habit of switching the base DPLL clock with every new revision
of the chips...
- switch to using the enumeration type to differ between the numerous chip
variants, matching PCI device/revision ID with the chip type early, at the
init_setup stage;
- extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
stop duplicating it for each channel by storing the pointer in the pci_dev
structure: first, at the init_setup stage, point it to a static "template"
with only the chip type and its specific base DPLL frequency, the highest
supported DMA mode, and the chip settings table pointer filled, then, at
the init_chipset stage, allocate per-chip instance and fill it with the
rest of the necessary information;
- get rid of the constant thresholds in the HPT37x PCI clock detection code,
switch to calculating PCI clock frequency based on the chip's base DPLL
frequency;
- switch to using the DPLL clock and enable UltraATA/133 mode by default on
anything newer than HPT370/A;
- fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
unify the HPT36x/37x setup code and the speedproc handlers by joining the
register setting lists into the table indexed by the clock selected;
- add enablebits for all the chips to avoid touching disabled channels
(though the HighPoint BIOS seem to only disable the primary one on
HPT371/N);
- separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
when setting an UltraDMA mode in hpt37x_tune_chipset().
This version has been tested on HPT370/302/371N.
Thanks to Alan for the inspiration. Hopefully, his libata driver will also
benefit from the work done on this "obsolete" driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clean up DMA timeout handling for HPT370:
- hpt370_lostirq_timeout() cleared the DMA status which made __ide_dma_end()
called afterwards return the incorrect result, and the DMA engine was reset
both before and after stopping DMA while the HighPoint drivers only do it
after (which seems logical) -- fix this and also rename the function;
- get rid of the needless mutual recursion in hpt370_ide_dma_end() and
hpt370_ide_dma_timeout();
- get rid of hpt370_lostirq_timeout() since hwif->ide_dma_end() called from
the driver's interrupt handler later does all its work.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Continue with the driver rewrite:
- move the interrupt twiddling code from the speedproc handlers into the
init_hwif_hpt366 which allows to merge the two HPT37x speedproc handlers
into one;
- get rid of in init_hpt366 which solely consists of the duplicate code, then
fold init_hpt37x() into init_chipset_hpt366();
- fix hpt3xx_tune_drive() to always set the PIO mode requested, not the best
possible one, change hpt366_config_drive_xfer_rate() accordingly, simplify
it a bit;
- group all the DMA related code together init_hwif_hpt366(), and generally
clean up and beautify it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Begin the real driver redesign. For the starters:
- cache the offset of the IDE channel's MISC. control registers which are used
throughout the driver in hwif->select_data;
- only touch the relevant MCR when detecting the cable type on HPT374's
function 1;
- make HPT36x's speedproc handler look the same way as HPT37x ones; fix the
PIO timing register mask for HPT37x.
- rename all the HPT3xx register related variables consistently; clean up the
whitespace.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Switch to using pci_get_slot() to get to the function 1 of HPT36x/374 chips --
there's no need for the driver itself to walk the list of the PCI devices, and
it also forgets to check the bus number of the device found.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- Rework the driver setup code so that it prefixes the driver startup
messages with the real chip name.
- Print the measured f_CNT value and the DPLL setting for non-HPT3xx
chips as well.
- Claim the extra 240 bytes of I/O space for all chips, not only for
those having PCI device ID of 0x0004.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- Rework hpt3xx_ratemask() and hpt3xx_ratefilter() so that the former
returns the max. mode computed at the load time and doesn't have to do
bad Ultra33 drive list lookups anymore; remove the duplicate code from
the latter function. Move the quirky drive list lookup into
hpt3xx_quirkproc() where it should have been from the start...
- Disable UltraATA/100 for HPT370 by default as the 33 MHz ATA clock
being used does not allow for it, and this *greatly* increases the
transfer speed.
- Save some space by using byte-wide fields in struct hpt_info; switch to
reading the 8-bit PCI revision ID reg. only, not the whole 32-bit reg.
- Start incrementing the driver version number with each patch (should
have been done from the first one posted).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the structures and routines needed for PS3 vuart port device registration
to asm-powerpc/ps3.h.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the PS3 system bus routines from drivers/ps3 to
arch/powerpc/platforms/ps3.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the inline function "is_power_of_2()" to log2.h, where the value
zero is *not* considered to be a power of two.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 irq allocation routines to take an argument indicating which
cpu (processor thread) the interrupt should be serviced on.
The current system configuration favors device interrupts that are serviced
on cpu0, so that is used as the default.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix two minor bugs in the PS3 system bus mmio region code. First, on error or
when freeing a region, retain the bus_addr and len fields to allow subsequent
calls to create the region. Second, correct the region address argument to the
lv1_unmap_device_mmio_region() call.
Fixes modprobe/rmmod of some drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes cpm uart able to work using OF-passed parameters
in case of CPM stuff (found on most mpc8xx reference and custom
boards). The idea is to keep ppc stuff working yet making it able to be
used for powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/net/amd8111e.c::amd8111e_poll() contains local_irq_disable() after
local_save_flags(). Turn it into local_irq_save().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/3c59x.c::poll_vortex() contains local_irq_disable() after
local_save_flags(). Turn it into local_irq_save().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pci_module_init() to pci_register_driver().
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Added ethtool support for user level firmware management utilities.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark this as 1.10 because WOL now works
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add WOL support for Yukon chipsets in skge device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use dev_printk related macros for PCI related errors and warnings
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some motherboards are broken and have no address set. Failing at probe time
prevents the device from ever being used (like to download a fixed BIOS). Instead
warn on probe and check again when device is brought up. That way the address
can be set.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
USB HID: handle multi-interface devices for Apple macbook pro properly
HID: move away from DEBUG defines in favor of CONFIG_HID_DEBUG
USB HID: fix bogus comment in hid_get_class_descriptor()
USB HID: remove hid_find_field_by_usage()
HID: API - fix leftovers of hidinput API in USB HID
HID: hid debug from hid-debug.h to hid layer
hid: force feedback driver for PantherLord USB/PS2 2in1 Adapter
hid: quirk for multi-input devices with unneeded output reports
hid: allow force feedback for multi-input devices
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Remove obsolete prototypes
IB/ehca: Remove use of do_mmap()
RDMA/addr: Handle ethernet neighbour updates during route resolution
IB: Make sure struct ib_user_mad.data is aligned
IB/srp: Don't wait for response when QP is in error state.
IB: Return qp pointer as part of ib_wc
IB: Include <linux/kref.h> explicitly in <rdma/ib_verbs.h>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (32 commits)
mmc: tifm: replace kmap with page_address
mmc: sdhci: fix voltage ocr
mmc: sdhci: replace kmap with page_address
mmc: wbsd: replace kmap with page_address
mmc: handle pci_enable_device() return value in sdhci
mmc: Proper unclaim in mmc_block
mmc: change wbsd mailing list
mmc: Graceful fallback for fancy features
mmc: Handle wbsd's stupid command list
mmc: Allow host drivers to specify max block count
mmc: Allow host drivers to specify a max block size
tifm_sd: add suspend and resume functionality
tifm_core: add suspend/resume infrastructure for tifm devices
tifm_7xx1: prettify
tifm_7xx1: recognize device 0xac8f as supported
tifm_7xx1: switch from workqueue to kthread
tifm_7xx1: Merge media insert and media remove functions
tifm_7xx1: simplify eject function
Add dummy_signal_irq function to save check in ISR
Remove unused return value from signal_irq callback
...
Replace uses of the obsolete pci_module_init function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed namespace collisions due to usage of nic_t as per Ralf's patch
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Fix for updating skb->truesize properly.
2. Disable NAPI only if more than one ring configured in case of MSI/MSI-X
interrupts. Previously we were disabling NAPI irrespective of number of
rings when MSI/MSI-X interrupts were used.
3. Code cleanup.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Fix for reset and link handling.
2. Allow for promiscuos mode and multicast state be maintained through
ifconfig up and down.
3. Support to print adapter serial number.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds two load parameters napi and ufo. Previously NAPI was
compilation option with these changes wan enable disable NAPI using load
parameter. Also we are introducing ufo load parameter to enable/disable
ufo feature
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch adds an alternative driver "pc300too" for PCI WAN
cards PC300/RSV and PC300/X21 made by Cyclades Corp. (now Avocent Corp).
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some cases, SG_DATA_INTR won't clear on read and the following
interrupt may cause us to assert because NAPI is already scheduled.
Remove the assertion, NAPI can handle attempts to rearm it while
it's already scheduled.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove a status error string from the pci-x context
and add it where it belongs - the pci-e context.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove tx credit coalescing done in SW.
The HW is caring care of it already.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up FW version checking.
The supported FW version is now 3.1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since it's no longer used, this "#define BCM_TSO 1" can now be removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A kmalloc casting cleanup patch.
Signed-off-by: Ahmed Darwish <darwish.07@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If alloc_etherdev() failed, then sky2_init_netdev will return NULL,
and sky2_probe would end up returning 0 instead of -ENOMEM.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain packet statistics in software rather than hardware.
This is slightly slower, but allows easier debugging of problems
where packets are still being received by PHY but not being handled
by hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch optimizes the data paths that can support hw counters. It
removes the sw counted statistics.
This is the last patch for the optimization set. Bumping up version of
driver.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces hw statistics for older devices that supported it.
It breaks up the counters supported into separate versions.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a limit to how much tx work can be done in each
iteration of tx processing. If the max limit is reached, remaining tx
completions will be handled by timer interrupt.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch optimizes the irq data paths and cleans up the code.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch optimizes the rx data paths and cleans up the code.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch optimizes the tx data paths and cleans up the code (removes
vlan from descr1/2 since only valid for desc3, changes to make code
easier to read, etc).
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch optimizes the logic for tx limiting. It adds a flag to check
on the completion side instead of recalculating the number of empty
slots. Also, it removes the fields that were previous used for limiting
since they have no value.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch breaks up the routines into two versions, one for legacy
descriptor versions (ver 1 and ver 2) and one for desc ver 3. This will
make the new desc functions more leaner and further reductions will be
made in next few patches.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The existing code would blindly attempt to create the
bonding_masters file (in /sys/class/net) every time the module was
loaded. When the module is loaded multiple times (which is the
historical method used by initscripts and sysconfig to create multiple
bonding interfaces), this caused load failure of the second module load
attempt, as the creation request would fail.
This changes the code to note the failure, arrange to not remove
the bonding_masters file upon module exit, and then return success.
Bonding interfaces created by the second or subsequent loads of
the module will not exist in bonding_masters. This is not a significant
change, as previously only the interfaces from the most recent load of
the module would be listed. Both situations are less than optimal, but
this case permits compatibility with existing distro configuration
scripts, and is consistent.
Note that previously, the sysfs create request would overwrite
the exsting bonding_masters file and succeed, allowing multiple loads of
the module. The sysfs code has recently changed to return an error if
the file being created already exists.
Patrick McHardy <kaber@trash.net>, who reported this problem,
observed crashes on the old kernel (before sysfs checked for
duplicates). I did not experience such crashes, but this change should
resolve them.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The existing code did not correctly handle failures to create
the per-interface sysfs group for bonding.
Modified code to notice errors, and correctly unwind.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to select names for the bonding interfaces was, for the
non-sysfs creation case, always using a hard-coded set of bond0, bond1,
etc, up to max_bonds. This caused conflicts for the second or
subsequent loads of the module.
Changed the code to obtain device names from dev_alloc_name().
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use bitrev8 for bmac, mace, macmace, macsonic, and skfp drivers.
[akpm@osdl.org: use the API, not the array]
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mirko Lindner <mlindner@syskonnect.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.
If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Qlogic 4032 chip is an incremental change from the 4022.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The OAKNET driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup receive processing some more:
* do the reserve padding of skb during setup
* don't pass constants to get_packet
* do smart prefetch of skb
* make copybreak a module parameter
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Speedup and cleanup the receive processing by eliminating the
mmio read and a lock round trip.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hdlc_setup was exported, but this export was never used.
If a driver using it actually shows up it can still be exported again.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes the code that recycled the skb on error. This will
help in reducing the branches in the main data paths.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reduces the amount of code within the lock to only the
critical sections.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch modifys ring access by using pointers. This avoids computing
the current index and avoids accessing the base address of the rings.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows the hardware to fetch the tx and rx ring descriptors
with 64 bytes per access instead of 32 bytes.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SKMC driver has:
- already been marked as BROKEN in 2.6.0 three years ago and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the Silan SC92031/Rsltek 8139D NIC chip.
This chip is found on at least one counterfeit Encore ENL832-TX-RENT NIC
[1], which came with a mini-CD with the 2.4 driver. A slightly older
version of the driver was found at [2]. The main difference between them
is that the newer one has a small bugfix in the RX path, a lot of
gratuitous renaming of functions, all the printable strings changed to show
as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead of 2031. The
driver on this patch is a rewrite of the vendor drivers (based mostly on
the older one).
Changes from the previous patch sent to netdev:
- Use MMIO instead of PIO
- Changed TX bounce buffers allocation
- Use skb_copy_and_csum_dev
- Several small bug fixes
- Tested for more than just a few minutes each time
[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
[3] To compile on 2.6.17, simply add back the last argument to the
interrupt handler in two places, and copy the boolean declarations
from 2.6.19
[akpm@osdl.org: build fixes]
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve power management and error handling by using pci_set_power_state(),
instead of driver doing PCI PM register changes in the driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some debugging and error printing.
The show_rx_chain() prints out the status of the rx chain,
which shows that the status of the descriptors gets
messed up after the second & subsequent RX ramfulls.
Print out contents of bad packets if error occurs.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delete possible source of chain corruption; the hardware
already knows the location of the tail, and writing it
again is likely to mess it up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add memory barrier to make sure that the rest of the
RX descriptor state is flushed to memory before we tell
the hardware that its ready to go.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tell the hardware the location of the rx ring tail.
More punctuation cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused variable; this makes code easier to read.
Tweak commentary.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The invocation of the rx ring refill routine is haphazard,
it can be called from a central location.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the somewhat convoluted use of return codes
in the rx buffer handling.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another skb leak in an error branch. Fix this by adding
call to dev_kfree_skb_irq() after moving to a more
appropriate spot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One of the unlikely error branches has an skb memory leak.
Fix this by handling the error conditions consistently.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no need to pass a flag into spider_net_decode_one_descr()
so remove this, and perform some othre minor cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of the rxramfull tasklet, and let the NAPI poll routine
deal with this situation. (The rxramfull interrupt is simply
stating that the h/w has run out of room for incoming packets).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds net_ratelimit to many of the printks in order to
limit extraneous warning messages (created in response to Bug 28554).
This patch supercedes all previous ratelimit patches.
This has been tested, please apply.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <jlinas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current driver code performs 512 DMA mappings of a bunch of
32-byte ring descriptor structures. This is silly, as they are
all in contiguous memory. This patch changes the code to
dma_map_coherent() each rx/tx ring as a whole.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Let's try to avoid some code duplication.
- cxgb2
The data are contiguous. Use plain memcpy.
- ixf1010/pm3393/vsc7326
The cast of &mac->stats to (u64 *) is not wonderful but it is not clear
if it is worth to add an ad-hoc union under the struct cmac_statistics.
vsc7326_reg.h suggests that more statistics could be available.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
- duplicated code in sge::free_cmdQ_buffers ;
- NET_IP_ALIGN is already defined in (included) <linux/skbuff.h> ;
- pci_alloc_consistent() returns void * ;
- pci_alloc_consistent() returns a zeroed chunk of memory ;
- early return in restart_tx_queues.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
pci_get_drvadata() is necessarily distinct from NULL if
cxgb2::init_one succeeded. cxgb2::remove_one is solely
issued through the PCI device callback.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch add ipw2200 support for iwconfig rts/frag auto.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Marijn Schouten
zd1211b chip 0586:340f v4810 high 00-13-49 AL2230_RF pa0 g---
FCC ID: I88G220V2
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for "ethtool -i" to prism54 driver.
ethtool -i queries the specified device for
associated driver information.
This helps tools like Fedora's system-config-network to
provide GUI management of network devices.
I learned how to write this patch by reading the ipw2100
driver code.
Signed-off-by: Kai Engert <kengert@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bcm43xx driver ignores any wireless-enable switches on mini-PCI
and mini-PCI-E cards. This patch implements a new routine to interrogate the
radio hardware enabled bit in the interface, logs the initial state and any
changes in the switch (if debugging enabled), activates the LED to show the
state, and changes the periodic work handler to provide 1 second response
to switch changes and to account for changes in the periodic work specs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Henrik Hjelte
zd1211b chip 13b1:0024 v4802 high 00-14-bf AL2230_RF pa0 ----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.
There are two ugly parts:
- fw_reg_addr() is needed to compute addresses of firmware registers, as this
is dynamic based upon firmware
- inc_addr() needs a small hack to handle byte vs word addressing
However, both of those are only small, and we don't use fw_regs a whole
lot anyway.
The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.
Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:
Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:
x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)
x_LEN: Segment length
x_y_LEN: Length of component y of segment x
x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)
I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many of the registers written during ZD1211 HMAC initialization are
duplicated exactly for ZD1211B. Move the identical ones into a generic
part, and write the hardware-specific ones separately.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver was still mis-calculating the number of bytes sent during
transmit, now the driver computes what appears to be exactly 100%
correct byte counts (not including CRC) when figuring out how many
bytes and frames were sent during the current transmit packet.
Since the driver sets the IP checksum insertion bit (IXSM in Status
field) in transmit context descriptors, it should clear the IP checksum
bits of any garbage so as not to confuse the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Print RX/TX flow control setting at link up time to display the
actual link FC properties instead of the advertised values.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This fix attempts to solve a customer (IBM) reported issue with NAPI
enabled e1000 having bad performance when transmitting simultaneously
on four ports. The issue comes down to an interaction between NAPI,
hardware interrupt balancing, and the driver rescheduling poll on
the same processor. Try to fix by allowing the driver to re-enable
interrupts sooner instead of polling one more time, when there was
recently all the work completed in cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unfortunately the read-free MSI interrupt handler needs to flush write
the icr register and thus we can't be read-free. Our MSI irq routine
thus becomes a lot more simpler since we don't need to track link state
anymore.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preset the bogomips number to the cpu capacity value reported by
store system information in SYSIB 1.2.2. This value is constant
for a particular machine model and can be used to determine
relative performance differences between machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
3592 tape devices are able to write data encrpyted on tape mediums.
This z/Linux device driver support includes the following functions:
* ioctl to switch on/off encryption
* ioctl to query encryption status of drive
* ioctls to set and query key encrypting keys (kekls)
* long busy interrupt handling
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Starting with the z9 the CPU Cryptographic Assist Facility comes with
an integrated Pseudo Random Number Generator. The generator creates
random numbers by an algorithm similar to the ANSI X9.17 standard.
The pseudo-random numbers can be accessed via a character device driver
node called /dev/prandom. Similar to /dev/urandom any amount of bytes
can be read from the device without blocking.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lower priority of "Blacklisted device detected" messages so we don't
overwrite more useful messages.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change CHSC event handling to be more easily extensible.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we have a subchannel id which has been generated via
for_each_subchannel(), it might contain an invalid subchannel set id.
We need to catch the ensuing operand exception by using stsch_err()
instead of stsch() in all possible cases.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The reserve/release IOCTLs sometimes do not work. If second system
does a 'steal lock' the pending unit check (Format 3 Msg F) is
delivered. Since ERP is disabled for reserve/release, the IOCTL call
fails. We have to allow basic ERP (retries) for reserve/release IOCTLs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Logging of relevant information is already done by disciplines
dump_sense function.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpu_relax() has barrier() semantics hence there is no need to use both
of them in conjunction in sclp_sync_wait(). Also change cpu_relax()
so it's more obvious that it has barrier semantics.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create/remove the channel measurement binary files with
device_{create,remove}_bin_file instead of sysfs_{create,remove}_bin_file.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
local_bh_disable/_local_bh_enable must not be called if in_irq() is
true. Besides that if in_interrupt() is true bottom halves are
disabled anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently loaded DCSS segments are now listed in /proc/iomem with
their name followed by a trailing "(DCSS)".
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we try to start path verification when an unsolicited interrupt
is already pending, stctl shows status pending and we delay path
verification again. We need to check for the doverify bit when the
unsolicited interrupt comes in and then do path verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The initialization of the dasd_eer code is one of the last steps of the
dasd driver initialization. When initialization fails in one of the
earlier steps, the dasd_exit function is called to clean up what has been
done so far. So the dasd_eer_exit function may be called, although the
dasd_eer_init function wasn't called before and dasd_eer_exit tries to
unregister a misc device that wasn't registered, which results in a BUG.
Make sure that dasd_eer_exit can be called without initialization. Use a
dynamically allocated struct miscdevice instead of a static one, so we
only try to unregister the device if it exists and was actually registered.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Requests are aborted when the sclp interface reports 'not operational'
even though they may still be active at the sclp, leading to concurrent
writes to request memory by both the kernel and the sclp interface.
Do not abort requests for which the sclp interface reports not
operational status during request retry.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>5A
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since ssd_info is now available before the subchannel is registered,
we don't need to check whether it is available.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some HID devices by Apple have both keyboard and mouse interfaces; the
keyboard interface is handled by usbhid, but the mouse (really
touchpad) interface must be handled by the separate 'appletouch'
driver. Using HID_QUIRK_IGNORE will make hiddev ignore both
interfaces, therefore a new quirk flag to ignore only the mouse
interface is required.
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_INPUT_DEBUG is non-existent option, so remove anything depending
on it.
Also, as we have new CONFIG_HID_DEBUG, this should be used on places
where ifdef DEBUG was used before.
Suggested by Adrian Bunk.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The comment in hid_get_class_descriptor() says a very obvious thing
and is also violating codingstyle. Just remove it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The unused hid_find_field_by_usage() function has been commented out for
a pretty long time. Remove it completely.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidinput_{open,close}() functions do not belong to usbhid, but
to the generic HID layer. Move them, and fix hooks in struct
hid_device, so that now the callbacks are done to transport-specific
_open() functions, but not input_open() functions.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-debug.h contains a lot of code, and should not therefore
be a header.
This patch moves the code to generic hid layer as .c source, and
introduces CONFIG_HID_DEBUG to conditionally compile it, instead
of playing with #define DEBUG and including hid-debug.h.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a force feedback driver for PantherLord USB/PS2 2in1 Adapter,
0810:0001. The device identifies itself as "Twin USB Joystick".
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new quirk HID_QUIRK_SKIP_OUTPUT_REPORTS to skip output reports
when enumerating reports on a hid-input device. Add this quirk and
HID_QUIRK_MULTI_INPUT to 0810:0001.
PantherLord Twin USB Joystick, 0810:0001 has separate input reports
for 2 distinct game controllers in the same interface, so it needs
HID_QUIRK_MULTI_INPUT. However, the device also contains one output
report per controller which is used to control the force feedback
function, and we do not want those to appear as separate input
devices as well. The simplest approach seems to be to add a quirk to
skip output reports on 0810:0001, and allow the force feedback
driver to handle those.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow hid devices with HID_QUIRK_MULTI_INPUT to have force feedback.
This was previously disabled because there were not any force
feedback drivers for such devices. This will change with my upcoming
patch.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove prototypes for functions that don't exist.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes do_mmap() from ehca:
- Call remap_pfn_range() for hardware register block
- Use vm_insert_page() to register memory allocated for completion
queues and queue pairs
- The actual mmap() call/trigger is now controlled by user space,
ie. libehca
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iWARP connection manager uses the ib_addr services to do route
resolution (neighbour discovery in the IP world). The ib_addr
netevent callback routine, however, currently only acts on InfiniBand
neighbour updates. It needs to act on ethernet neighbour updates as
well.
This patch just removes filtering on device type altogether and will
trigger on any neighour updates where the nud_type is valid. This
simplifies the code some.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When there is a call to send_tsk_mgmt SRP posts a send and waits for 5
seconds to get a response.
When the QP is in the error state it is obvious that there will be no
response so it is quite useless to wait. In fact, the timeout causes
SRP to wait a long time to reconnect when a QP error occurs. (Each
abort and each reset_device calls send_tsk_mgmt, which waits for the
timeout). The following patch solves this problem by identifying the
failure and returning an immediate error code.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC high-speed, wide bus support and SD high-speed
are functions that aren't critical for correct
operation of the card. As such, they shouldn't mark
the card as bad or dead when there is a failure
activating these features.
This is needed in particular on some really stupid
hardware (e.g. Winbond's) where not all data transfer
commands are supported.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wbsd hardware is so incredibly brain damaged that it has an internal
list of commands that result in data transfers. The result being that
commands that aren't on this list aren't supported.
Instead of locking up, waiting for a data interrupt that will never come,
we try to fail a bit more gracefully.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Many controllers have an upper limit on the number of blocks that can be
transferred in one request. Allow the host drivers to specify this and make
sure we avoid hitting this limit.
Also change the max_sectors field to avoid confusion. This makes it map
less directly to the block layer limits, but as they didn't apply directly
on MMC cards anyway, this isn't a great loss.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix some spaces and tabs. No semantic changes are introduced.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch also adds symbolic defines for supported pci ids.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As there's only one work item (media_switcher) to handle and it's effectively
serialized with itself, I found it more convenient to use kthread instead of
workqueue. This also allows for a working implementation of suspend/resume,
which were totally broken in the past version.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hardware does not say whether card was inserted or removed when reporting
socket events. Moreover, during suspend, media can be removed or switched
to some other card type without notification. Therefore, for each socket
in the change set the following is performed:
1. If there's active device in the socket it's unregistered
2. Media detection is performed
3. If detection recognizes supportable media, new device is registered
This patch also alters some macros and variable names to enhance clarity.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Eject function can take advantage of the socket_id field instead of explicit
pointer comparison.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch introduces no semantic changes - it is here for estetic purposes.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In order to support correct suspend and resume several changes were needed:
1. Switch from work_struct to tasklet for command handling. When device
suspend is called workqueues are already frozen and can not be used.
2. Separate host initialization code from driver's probe and don't rely
on interrupts for host initialization. This, in turn, addresses two
problems:
a) Resume needs to re-initialize the host, but can not assume that
device interrupts were already re-armed.
b) Previously, probe will return successfully before really knowing
the state of the host, as host interrupts were not armed in time.
Now it uses polling to determine the real host state before returning.
3. Separate termination code from driver's remove. Termination may be caused
by resume, if media changed type or became unavailable during suspend.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The register access order when setting hardware timeout was incorrect and
causing problems (wrong timeout intervals). This is now fixed.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Two changes are introduced to software timeout handler in order to simplify
its management:
1. The implementation is switched from work_struct to timer
2. Previously, software timeout was rearmed with each interrupt. Now,
current request must complete entirely within timeout interval.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data buffer for PIO transfer used to be mapped in advance with kmap.
Abolish it in favor of on-demand kmap_atomic.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Previously, stop command was issued right after BRS (block received/sent)
event. Stop command completion event could interfere with the card busy
event, causing miscount of the written blocks.
This patch ensures that stop command issued as last action for a
particular command, after DMA sompletion event and written block
count verification.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:
i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.
ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.
iii) Read and write timeouts are fixed values and not calculated from
CSD values.
iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change the parent of cards to be a specific host (a class
device), not the physical controller. This is particularly
useful when the hardware has multiple slots, meaning
multiple hosts.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As card_busy was only used to indicate if the host was exclusively
claimed and not really used to identify a particular card, replacing
it with just a boolean makes things a lot more easily understandable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
That code doesn't do what its author apparently thought it would do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning
smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set fake hid for ejectable drive bay.
Match bay devices by checking the hid.
Remove .match method of Bay driver.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert the bay driver to be a platform driver, so that we can have
sysfs entries.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove all the procfs related code.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When determining if a device is on a dock station, we should
check the parent of the device as well.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/namespace/nsparse.c:126: warning: int format, different type arg (arg 7)
drivers/acpi/tables/tbfadt.c:224: warning: unsigned int format, different type arg (arg 6)
drivers/acpi/utilities/utdebug.c:184: warning: cast from pointer to integer of different size
drivers/acpi/utilities/utdebug.c:184: warning: cast from pointer to integer of different size
drivers/acpi/utilities/utdebug.c:197: warning: cast from pointer to integer of different size
drivers/acpi/processor_idle.c:1093: warning: long long unsigned int format, u64 arg (arg 5)
Signed-off-by: Len Brown <len.brown@intel.com>
Support for dynamic loading and unloading of ACPI SSDT tables upon slot
hotplugs and unplugs.
On SN platforms, we now represent every populated root bus slot with a single
ACPI SSDT table containing info for every device and PPB attached to the slot.
These SSDTs are generated by the prom at initial boot and hotplug time. The
info in these SSDT tables is used by the SN kernel IO "fixup" code (which is
called at boot and hotplug time).
On hotplugs (i.e. enable_slot()), if running with an ACPI capable prom,
attempt to obtain a new ACPI SSDT table for the slot being hotplugged. If
successful, add the table to the ACPI namespace (acpi_load_table()) and then
walk the new devices and add them to the ACPI infrastructure (acpi_bus_add()).
On hot unplugs (i.e. disable_slot()), if running with an ACPI capable prom,
attempt to remove the SSDT table associated with the slot from the ACPI
namespace (acpi_unload_table_id()) and infastructure (acpi_bus_trim()).
From: John Keller <jpk@sgi.com>
A bug was fixed where the sgi hotplug driver was removing
the slot's SSDT table from the ACPI namespace a bit too early in
disable_slot(). Also, we now call acpi_bus_start() subsequent
to acpi_bus_add().
Signed-off-by: Aaron Young <ayoung@sgi.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown<len.brown@intel.com>
Copy space_id of GAS structure to newly created GAS.
The previous FADT conversion code defaulted to IO space.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bad pointer was passed in the case where the DSDT is overridden.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added 2007 copyright to all module headers and signons. This affects
virtually every file in the ACPICA core subsystem, iASL compiler,
and the utilities.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow processor to be declered with the Device(), such as:
Device(CPU1234) {
Name(_HID, "ACPI007")
Name(_UID, 1234)
}
Signed-off-by: Len Brown <len.brown@intel.com>
Debugger: Enhanced the Statistics/Memory command to emit the
total (maximum) memory used during execution, as well as the
maximum memory consumed by each of the various object types.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Support for 16-bit ACPICA has been completely removed since it is
no longer necessary and it clutters the code. All 16-bit macros,
types, and conditional compiles have been removed, cleaning up
and simplifying the code across the entire subsystem.
DOS support is no longer needed since the Linux firmware kit
is now available.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
AcpiEnable will now fail if all of the required ACPI tables are not
loaded (FADT, FACS, DSDT). BZ 477
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added AcpiEvRemoveGlobalLockHandler
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optimized the Load operator in the case where the source operand is an
operation region. Simply map the operation region memory, instead of
performing a bytewise read.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Extra checks for valid handle/path combinations, BZ 478
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhancement to code that ignores temporary namespace nodes
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented _CID support for PCI Root Bridge detection. If the _HID
does not match the predefined root bridge IDs, the _CID list (if present)
is now obtained and also checked for an ID match
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with a possible race condition between threads executing
AcpiWalkNamespace and the AML interpreter. This condition was removed by
modifying AcpiWalkNamespace to (by default) ignore all temporary
namespace entries created during any concurrent control method execution
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed an AML interpreter performance enhancement for control method
execution. Previously a 2-pass parse/execution, control methods are now
completely parsed and executed in single pass. This improves overall
interpreter performance by ~25%, reduces code size, and reduces CPU stack use.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Restructured the AML ParseLoop function, breaking it into several
subfunctions in order to reduce CPU stack use and improve maintainability
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a possible memory leak and fault in acpi_ex_resolve_object_to_value()
during a read from a buffer or region field. (BZ 458)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove flags parameter for acpi_{get,set}_register().
It is no longer necessary now that these functions use a
spinlock for mutual exclusion.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the Global Lock where the lock could appear to be obtained before it is actually obtained, semaphore created with one unit.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a regression where an error was no
longer emitted if a control method attempts to create 2
objects of the same name. This previously and now returns
AE_ALREADY_EXISTS. When this exception occurs, it invokes
the mechanism that will dynamically serialize the control
method to possible prevent future errors. (BZ 440)
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Useful during disassembly where the target may
be in a different table and thus the type is unknown.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Required new table init interface since iASL does not use RSDP/XSDT.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved all FADT-related functions to a new file, tbfadt.c.
Eliminated the acpi_hw_initialize function - the
FADT registers are now validated when the table is loaded.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhanced the implementation of the interpreters'
serialized mode (boot with "acpi_serialize" to set
acpi_glb_all_methods_serialized flag.)
When this mode is specified, instead of creating a serialization
semaphore per control method, the interpreter lock is
simply no longer released before a blocking operation
during control method execution. This effectively makes
the AML Interpreter single-threaded. The overhead of a
semaphore per-method is eliminated.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed offset display, not needed.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split acpi_format_exception into two parts. New
function is acpi_ut_verify_exception and will be used to
verify exception codes returned by user.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update internal GPE data structure to simplify
debug, use gpe_number instead of register bitmask.
Signed-off-by: Bob Moore <bob.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update interface to acpi_ut_repair_name() to avoid
alignment issues on IA64
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change for GPE support: when a wake GPE is
received, now all wake GPEs are immediately disabled to
prevent the waking GPE from firing again, and to prevent
other wake GPEs from interrupting the wake process.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lint changes
Move RSDT/XSDT pointer extraction to separate function
Warning on 32-bit platforms if XSDT pointers use more than 32 bits.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Table Manager component has been completely
redesigned and reimplemented. The new design is much
simpler, and reduces the overall code and data size of
the kernel-resident ACPICA by approximately 5%. Also,
it is now possible to obtain the ACPI tables very early
during kernel initialization, even before dynamic memory
management is initialized.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Temporary fix for BankValue parameter of a Bank
Field to support all constant values, including Zero
and One. Must eventually be converted to a full TermArg
evaluation.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix for object premature deletion after CopyObject
on Operation Region (BZ 350)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI Global Lock interrupt handler no longer
queues the execution of a separate thread to signal the
global lock semaphore. Instead, the semaphore is signaled
directly from the interrupt handler.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a new design and implementation for
the ACPI Global Lock support. On the OS side, the global
lock is now treated as a standard AML mutex. Previously,
multiple OS threads could acquire the global lock
simultaneously, but this could cause the BIOS to be starved
by the lock in cases such as the Embedded Controller driver,
where there is a tight coupling between the OS and the BIOS.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Additional update for NumElements fix. Must handle
case where NumElements > Package list length, pad package
with null elements.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implement support within the AML interpreter for
package objects that contain a mismatch between the AML
length and package element count. In this case, the lesser
of the two is used. Some BIOS code apparently modifies
the package length on the fly, and this change supports
this. Provides compatibility with the MS AML interpreter.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
...by disabling CONFIG_ACPI when CONFIG_X86_NUMAQ=y
otherwise arch/i386/pci/Makefile forgets
that it needs to build acpi.o
drivers/built-in.o: In function `acpi_pci_root_add':
pci_root.c:(.text+0x45ec4): undefined reference to `pci_acpi_scan_root'
Signed-off-by: Len Brown <len.brown@intel.com>
sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 8237S was added to the chipsets but not to the comments. Fix this
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set. This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.
The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits. If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.
This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We forget to call spider_net_free_rx_chain_contents which does the
actual dev_kfree_skb. New skbs are allocated from skbuff_head_cache
on each "ifconfig up" letting the cache grow infinitely.
This patch fixes it.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e100: fix napi ifdefs removing needed code
From: Auke Kok <auke-jan.h.kok@intel.com>
The e100 driver is NAPI mode only. We need to netif_poll_disable
during suspend and shutdown. The non-NAPI driver code was removed
and is only avaiable in the out-of-tree e100 kernel driver.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
5709 A0 copper devices will not link up with some link partners
without this workaround.
Update driver to 1.5.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change SysRq showBlockedTasks from sysrq-X to sysrq-W and show that in the
Help message.
It was previously done via X, but X is already used for Xmon on ppc & powerpc
platforms and this collision needs to be avoided.
All callers of register_sysrq_key() are now marked in the sysrq op/key table.
I didn't mark 'h' as Help because Help is just printed for any unknown key,
such as '?'.
Added some omitted sysrq key entries in the sysrq.txt file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel hosts, without long mode, and with nx support disabled in the bios
have an efer that is readable but not writable. This causes a lockup on
switch to guest mode (even though it should exit with reason 34 according
to the documentation).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove these recently-added warnings. They don't tell us anythng very
interesting and Kumar says "On an embedded PPC reference system I see this
message 6 times when I've got no cards in the PCI slots."
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add special handling for the VT82C686.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Won't build (request_irq()/free_irq()), even if you manage to find an
s390 box with 8250-compatible UART they are expecting.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) cleanup_module() should be __exit
b) externs should match reality
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI_BUTTON_HID_POWERF was changed, but this change was not propogated to
button.c, thus breaking detection of fixed power and sleep buttons.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix pb_fnmode and move it to generic HID
HID: fix hid-input mapping for Firefly Mini Remote Control
USB HID: fix hid_blacklist clash for 0x08ca/0x0010
HID: fix memleaking of collection
Fix a dangling pointer bug in ipmi_timeout_handler. A list of timedout
messages is not re-initialized before reuse, causing the head of the list
to point to freed memory.
Signed-off-by: David Barksdale <amatus@ocgnet.org>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
jmicron module detects all JMB36x as JMB361 and PATA0 has wrong pin status
of XICBLID.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix VIA quirks that were recently broken by Alan Cox in the upstream
kernel (commit 1597cacbe3).
My understanding is that pci_find_present() doesn't work yet at the time
the quirks are run. So I used a two-step quirk as is done for some other
quirks already. First we detect the VIA south bridges and set the right
low and high device limits, then we are ready to actually run the quirks on
the affected devices.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 0c0b3ae68e.
Quoth David:
"Jeff, please revert
It's wrong. We had a lengthy analysis of this piece of code
several months ago, and it is correct.
Consider, if we run the loop and we get an error
the following happens:
1) attempt of ifb_init_one(i) fails, therefore we should
not try to "ifb_free_one()" on "i" since it failed
2) the loop iteration first increments "i", then it
check for error
Therefore we must decrement "i" twice before the first
free during the cleanup. One to "undo" the for() loop
increment, and one to "skip" the ifb_init_one() case which
failed."
Reported-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix translation for START STOP UNIT
libata-scsi: ata_task_ioctl should return ATA registers from sense data
pata_platform: set_mode fix
ata_if_xfermask() word 51 fix
pata_sil680: PIO1 taskfile transfers overclocking fix (repost)
libata: fix ata_eh_suspend() return value
ahci: port_no should be used when clearing IRQ in ahci_thaw()
Fix trivial conflict in drivers/ata/pata_platform.c manually
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Add new IDs to VIA AGP.
[AGPGART] Remove pointless assignment.
[AGPGART] Remove pointless typedef in ati-agp
[AGPGART] Prevent (unlikely) memory leak in amd_create_gatt_pages()
[AGPGART] intel_agp: restore graphics device's pci space early in resume
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx/pata_via: correct PCI_DEVICE_ID_VIA_SATA_EIDE ID and add support for CX700 and 8237S
ide: unregister idepnp driver on unload
ide: add missing __init tags to IDE PCI host drivers
ia64: add pci_get_legacy_ide_irq()
ide/generic: Jmicron has its own drivers now
atiixp.c: add cable detection support for ATI IDE
atiixp.c: sb600 ide only has one channel
atiixp.c: remove unused code
jmicron: fix warning
ide: update MAINTAINERS entry
What DMA for 16bit pcmcia card, anyway? We never do request_dma()
there and ->dma_channel never changes since initialization to -1.
IOW, that call is dead code.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4117/1: S3C2412: Fix writel() usage in selection code
[ARM] 4111/1: Allow VFP to work with thread migration on SMP
[ARM] 4112/1: Only ioremap to supersections if DOMAIN_IO is zero
[ARM] 4106/1: S3C2410: typo fixes in register definitions
[ARM] 4102/1: Allow for PHYS_OFFSET on any valid 2MiB address
[ARM] Fix AMBA serial drivers for non-first serial ports
[ARM] 4100/1: iop3xx: fix cpu mask for iop333
[ARM] Update mach-types
[ARM] Fix show_mem() for discontigmem
[ARM] 4096/1: S3C24XX: change return code form s3c2410_gpio_getcfg()
[ARM] 4095/1: S3C24XX: Fix GPIO set for Bank A
[ARM] 4092/1: i.MX/MX1 CPU Frequency scaling latency definition
[ARM] 4089/1: AT91: GPIO wake IRQ cleanup
[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
[ARM] 4087/1: AT91: CPU reset for SAM9x processors
[ARM] 4086/1: AT91: Whitespace cleanup
[ARM] 4085/1: AT91: Header fixes.
[ARM] 4084/1: Remove CONFIG_DEBUG_WAITQ
Fix what looks like an obvious typo in the file drivers/kvm/svm.c.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some issues in b44_resume().
- Return value of pci_enable_device() was ignored.
- If request_irq() has failed we have to just disable device and exit.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e100: fix irq leak on suspend/resume
From: Frederik Deweerdt <frederik.deweerdt@gmail.com>
The e100_resume() function should be calling netif_device_detach and
free_irq. This fixes multiple irq's being allocated after resume.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While working with the latest bonding code I noticed a nasty problem that
will prevent arp monitoring from always functioning correctly on x86_64
systems. Comparing ints to longs and expecting reliable results on x86_64
is a bad idea. With this patch, arp monitoring works correctly again.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the wrong query and logging of the per interface jumbo frames
enabled/disabled status.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1069: warning: cast from pointer to integer of different size
drivers/net/82596.c: In function 'i82596_probe':
drivers/net/82596.c:1249: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updated direct resource pass with ioremap call, make it grant proper IRQ
mapping, stuff incompatible with the new approach were respectively put
under #ifndef CONFIG_PPC_MERGE. It is required so that both ppc and
powerpc could utilize fs_enet effectively.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On error we should start freeing resources at [i-1] not [i-2].
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the issue of frequent link changes under heavy traffic reported
below:
http://bugzilla.kernel.org/show_bug.cgi?id=7696https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=216338
The b44 chip occasionally needs to be reset when ISTAT_ERRORS are
encountered. The reset sequence includes a PHY reset that will take many
seconds to complete and cause the link to go down and up. By skipping the
PHY reset, it will greatly reduce the interruption when ISTAT_ERRORS are
encountered.
Change the full_reset parameter to reset_kind parameter in b44_init_hw().
This will allow PHY reset to be skipped when ISTAT_ERRORS are encountered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata's SCSI translation for the SCSI START STOP UNIT command with the
START bit clear (i.e. stopping the drive) appears to be incorrect. It
sends an ATA STANDBY command with the time period set to 0, which the code
comment says means "now", but the ATA standard says this means disable the
standby timer, which effectively does nothing. Change this to issue a
STANDBY IMMEDIATE command which will actually spin the drive down. The SAT
(SCSI/ATA Translation) standard revision 9 concurs with this choice.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
User applications using the HDIO_DRIVE_TASK ioctl through libata expect
specific ATA registers to be returned to userspace. Verified that
ata_task_ioctl correctly returns register values to the smartctl
application.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/pata_platform.c:85: warning: initialization from incompatible pointer type
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If word 53 bit 1 isn't set, the maximum PIO mode is indicated by
the upper 8 bits of word 51, not the lower 8 bits. Fixes PIO mode
detection on old Compact Flash cards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix PIO mode 1 overclocked taskfile transfers -- probably a typo carried over
from drivers/ide/pci/siimage.c where I've found it by documentation check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.
This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-#ifdef CONFIG_ACPI_DEBUG_OUTPUT
+#ifdef ACPI_DEBUG_OUTPUT
As the former doesn't exist.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/proc/acpi/asus/lslvl is now /sys/.../asus-laptop/ls_level
/proc/acpi/asus/lssw is now /sys/.../asus-laptop/ls_switch nothing
else ..
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Ledd is a special led ... /sys/.../asus-laptop/ledd works like
/proc/acpi/asus/ledd
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
/sys/.../asus-laptop/display can now be used to switch displays
like the old /proc/acpi/asus/disp does
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds backlight support using backlight class. We now
change the brightness *and toggle the backlight !* via
/sys/class/backlight/asus-laptop/.
If the user switchs the backlight using the keyboard,
asus_hotk_notify looks for ATKD_LCD_OFF and ATKD_LCD_ON events,
and stores the right state into hotk->status and bd->props->power .
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
WLED and BLED are not handled like other leds (MLED, etc ..),
because sometime they also control the wlan/bluetooth device.
If the method for wireless_status is found, it's used to get the
status, otherwise hotk->status is used. We also use the HWRS
method, which tell if the bluetooth/wlan device is present or not.
This patch show why we need a ASUS_SET_DEVICE_ATTR macro : if
there is a bluetooth device, /sys/dev.../asus-laptop/bluetooth
is usable, else it's not but it's clean.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Add led support, using generic led class. Thomas Tuttle's patch
<http://lkml.org/lkml/2006/7/6/247> was very usefull. We use
hotk->status to store led status because it's very hard to find
acpi method to get the right status... To reduce the code,
I use a lot of macro (ASUS_LED, ASUS_LED_REGISTER, etc ...),
because the code is the same for all leds ...
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds the new driver and make ASUS_LAPTOP and ACPI_ASUS
incompatible. It may be strange to use ASUS_CREATE_DEVICE_ATTR
and ASUS_SET_DEVICE_ATTR now, but these macro will be very
usefull in next patchs. ASUS_HANDLE and ASUS_HANDLE_INIT comes
from IBM_HANDLE and IBM_HANDLE_INIT, with some modification,
and will also be used in next patchs.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Let's just backout the IRQ hack, and for those crap machines (like some
Sony VAIO's) can just disable MSI with the module parameter.
This reverts 44ade17824.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frédéric Riss <frederic.riss@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch to check sysfs_create_link return values.
Fail gracefully if needed.
Signed-off-by: Ahmed Darwish <darwish.07@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add an ACPI attribute to indicate ACPICA version.
/proc/acpi/version is deprecated by /sys/module/acpi/parameters/acpica_version.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Sergei Shtylyov
Andrew Morton
Paul Mackerras
Ishizaki Kou
Vitaly Bordug
Geoff Levand
Robert P. J. Day
Benjamin Herrenschmidt
Jiri Kosina
Richard Knutsson
Amit S. Kale
Stephen Hemminger
Al Viro
Linus Torvalds
Len Brown
Olof Johansson
Ralf Baechle
Sivakumar Subramani
Krzysztof Halasa
Divy Le Ray
Adrian Bunk
Ahmed S. Darwish
YOSHIFUJI Hideaki / 吉藤英明
Ayaz Abdulla
Jay Vosburgh
Akinobu Mita
Ron Mercer
Stephen Hemminger
Cesar Eduardo Barros
Arjan van de Ven
Linas Vepstas
Francois Romieu
Zhu Yi
Daniel Drake
Kai Engert
Larry Finger
Auke Kok
Jesse Brandeburg
Bruce Allan
Heiko Carstens
Martin Schwidefsky
Michael Holzheu
Jan Glauber
Cornelia Huck
Peter Oberparleiter
Horst Hummel
Gerald Schaefer
Stefan Weinhuber
Soeren Sonnenburg
Anssi Hannula
Hoang-Nam Nguyen
Steve Wise
Ishai Rabinovitz
Michael S. Tsirkin
Pierre Ossman
Alex Dubov
Philip Langdale
Darren Salt
Manuel Lauss
Al Viro
Peter Korsgaard
Zhang Rui
Kristen Carlson Accardi
Alexey Starikovskiy
John Keller
Bob Moore
Alexey Starikovskiy
Valery A. Podrezov
Mikhail Kouzmich
Fiodor Suietov
Nagendra Singh Tomar
Brian King
Alan
Tejun Heo
Jens Osterkamp
Auke Kok
Jeff Garzik
Michael Chan
Bartlomiej Zolnierkiewicz
Randy Dunlap
Avi Kivity
Jean Delvare
David Barksdale
ethanhsiao@jmicron.com
Dmitriy Monakhov
Andy Gospodarek
Thomas Klein
Mariusz Kozlowski
Robert Hancock
David Milburn
Lennert Buytenhek
Corentin Chary