Remove the temp2_type sysfs files for f8000 / f71858fg models,
this got in accidentally and is wrong as these models don't have a
Temperature Sensor Type Register at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the temp sysattr array for the standard models a 2d array, which allows
to use it for models with less temperatures too. This is a preparation
patch for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for adding support for more different models,
some of which have a sparse list of used voltage pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code for determining a sensort type for temp1 was based on me misreading
the datasheet, the tested registers do not determine what kind of sensor
is actually reported as temp1. Instead the enable / disable certain additional
digital sensor readouts throug PECI / AMDSI, etc. Independent of these settings
temp1 is still reading an external BJT or thermistor as configured by the
Temperature Sensor Type Register (0x6b).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Systems with NCT6775F reported temperature sensor labels for systems with
NCT6776F. This patch fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
NCT6776F and NCT6775F support debouncing the fan RPM signal. This can
help improve the stability of th RPM signal for some fans (Arctic cooling
fans for example).
This patch adds a module parameter fan_debounce, which when set to 1 enables
debounce for all fans that the chip supports.
Signed-off-by: Ian Dobson <i.dobson@planet-ian.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since the fan speed value can be above 0xff, we can no longer use
that value to determine if the fan speed reading is valid. This
makes it difficult to manipulate the stored fan speed register value.
If we store rpm instead of the fan speed register value, we do not
need to correct it if the fan divisor value is changed, and the above
mentioned problem no longer exists.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Some of the chips supported by this driver have 13 bit or 16 bit fan count
registers. This patch improves support for those registers, specifically for
NCT6775F. With the changes in this patch, fan speed is reported correctly even
if the fan divider is set to a low value, which results in a fan speed reading
above 0xff.
With this patch, the width of fan count registers is no longer used to determine
if the chip has fan divider register(s) or not. A dedicated flag is used instead
to determine if this is the case.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch adds support for NCT6775F and NCT6776F to the w83627ehf driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Ian Dobson <i.dobson@planet-ian.com> (NCT6776F)
Tested-by: Zachary Marzec <zmarzec@gmail.com> (ASUS P8P67 PRO/NCT6776F)
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
If SmartFan IV mode was configured at startup, it should be possible
to re-enable it later on.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
For newer chips, several registers are banked and thus need to be 16 bit.
Also, register addresses change.
To prepare for those chips, convert affected register arrays to 16 bit,
and change access to those registers to array pointers in struct w83627ehf_data.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Assume that each register is banked, and set the bank for each access.
Cache the bank number so it only needs to be set if it changes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This cleanup fixes most of the checkpatch warnings and errors in the w83627ehf
driver. Remaining warnings and errors are left untouched on purpose to avoid
making the code less readable.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch unifies temperature register access, and replaces simple_strtoXXX
with strict_strtoXXX throughout the driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
LTC4151 is High Voltage I2C Current and Voltage Monitor from Linear
Technology.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
LINEAR16 data format is unsigned, not signed. Impact is that affected
attributes report negative values in the upper half of the supported
value range.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
PMBus only has one set of limit registers for up to three temperature sensors.
Thus, changing a limit for one of the temperature sensors affects limits for
other temperature sensors in the same page (and potentially multiple pages
depending on the chip implementation). To handle this situation, re-read all
temperature limit registers when updating sensor data. This way, all affected
temperature limits are updated whenever the limit for a single sensor is
changed.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Assumption so far was that PMBus devices would support TEMP2 and TEMP3 registers
only on page 0, and that only the TEMP1 register would be used/supported
on other pages.
Turns out that is not correct. UCD92xx devices support TEMP1 and TEMP2 on
page 0, and TEMP2 on other pages. So it is necessary to change the core code
such that it does not make a page based assumptions about temperature register
support.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
So far, it seemed like fans would either all be in page 0, or that
there would be one page per fan.
Turns out this was a wrong assumption. There is at least one PMBus
fan controller which supports three pages with four fans each.
Update code to handle this situation.
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
Some PMBus chips do not support the VOUT_MODE register. To make matters worse,
such chips may not return an error when reading the register either, but instead
return 0xff.
Check if the register exists using pmbus_check_byte_register() before reading
its value. In addition, validate the returned value and ignore it if it is 0xff
(which is invalid).
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
EMC6D103S is similar to EMC6D103, only it does not support registers 62[5:7],
6D[0:7], and 6E[0:7]. Register respective sysfs attributes and update affected
registers for all other chips only.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, the driver updates temp_auto_hyst and temp_auto_off if temp_auto_min changes.
This may cause problems if temp_auto_off was not configured before configuring
temp_auto_min, because one of the variables used (off_desired) is not initialized
in this case.
To simplify the code, and for consistency with other drivers, no longer update the delta
between "min" and "off" until the user sets the "off" value again.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADT7463 and ADT7468 optionally support VID5 instead of the standard +12V
measurement input. Use a boolean to identify the chip configuration instead of
hardcoding it several times.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the lis3lv02d SPI driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch initializes register CONFIG3 to a reasonable default PWM frequency
of 25kHz, to prevent audible sound in fan.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This avoids a possible race leading to trying to dereference NULL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
On systems where the temperature sensor is actually used, the BIOS is
likely to have locked the alarm registers. In that case, all writes
through the corresponding sysfs files would be silently ignored.
To prevent this, detect the locks and make the affected sysfs files
read-only.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In set_temp_crit_hyst(), make the variable 'val' have the correct
type for strict_strtoul().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
I2C address range included 0x2a, which the chips do not support.
Replace with 0x29 which is supported but was missing.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
LM64 has 16 degrees Celsius temperature offset on all
remote sensor registers.
This was not considered When LM64 support was added to lm63.c.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Turn down the no IRQ message - on some platforms that's a normal state of
affairs.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ASUS Sabertooth X58 has a bug in ACPI that prevents the reading of MCH
temperature when the "old" ATK0110 interface is used. Add a DMI entry
to override the detection heuristic and force the use of the "new"
interface on this board.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Joris Creyghton <jorisctn@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The switch to dynamically allocated sysfs attributes left the
internal lockdep members uninitialized, causing a formal bug.
This patch adds sysfs_attr_init() to the node creation function,
remedying the problem.
Reported-and-tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Minor cleanups. Mostly removing assignments in if statements to get
rid of checkpatch errors.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the 1.5V voltage monitoring input (in7) of the
SMSC SCH5127 chip.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
EMC1423 uses the similar register and adds a hardware shutdown pin to
protect exceed temperature. This function is set by resistor; it's not
necessary to do anything in the driver except add the emc1423 pid of 0x23.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
[Updated Kconfig/comments and minor further changes asked for by the hwmon
maintainers]
Signed-off-by: Alan Cox <alan@linux.intel.com>
[Fixed checkpatch warning]
Signed-of--by: Jean Delvare <khali@linux-fr.org>
This is the same case as fschmd, from which the code was copied as far
as I can see. So the same clean-up applies:
The WDIOC_GETSUPPORT ioctl only needs a mutex because it operates on a
static variable. There is no good reason to keep this variable static,
so let's just make it non-static and drop the now useless mutex
altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
As discussed one year ago, the WDIOC_GETSUPPORT ioctl only needs a
mutex because it operates on a static variable. There is no good
reason to keep this variable static, so let's just make it non-static
and drop the now useless mutex altogether.
See the discussion at:
http://marc.info/?l=lm-sensors&m=125563869402323&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
[JD: Also convert debug messages]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We have a standard intrusion detection interface now, drivers should
implement it. I've left the old interface in place for the time being,
with a deprecation warning, it will be removed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code triggers a false warning with older versions of gcc:
w83795.c: In function 'w83795_update_device':
w83795.c:475: warning: 'lsb' may be used uninitialized in this function
I admit that the code is a little tricky, but I see no way to write it
differently without hurting performance. So let's just silent the
warning with a needless initialization.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Trivial patch updating my email contact details due to change of
employer, and because I no longer have access to the previously used
domain.
Unfortunately I also no longer have access to any ads7828 hardware, but
am happy to support/maintain the driver if others are able to test
changes.
Signed-off-by: Steve Hardy <shardy@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch fixes all checkpatch errors and most of the checkpatch warnings.
It also fixes the range check in applesmc_store_fan_speed().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
With the preceding patches, git blame assigns about half of
the file to the present author. Add a line to the copyright
to reflect this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the driver report a single line on success.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Given the dynamic node construction method, the setup of the
accelerometer, light sensor and keyboard backlight sysfs nodes
can be simplified. This patch does not contain any logic changes.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With the dynamic temperature group in place, the setup of fans
can be simplified. This patch sets up the fans dynamically, removing
a hundred lines of code.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With temperature keys being determined automatically, the dmi match
data is only used to assign features that can easily be detected from
the smc. This patch removes the dmi match data altogether, and reduces
the match table to the main machine models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent Macbooks have temperature registers of a new type.
This patch adds the logic to handle them.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The current driver creates temperature files based on a list
of temperature keys given per device. Apart from slow adaption
to new machine models, the number of sensors also depends on
the number of processors. This patch looks up the temperature
keys dynamically, thereby supporting all models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
One main problem with the current driver is the inability to quickly
search for supported keys, resulting in detailed feature maps per
machine model which are cumbersome to maintain.
This patch adds a register lookup table, which enables binary search
for supported keys. The lookup also reduces the io frequency, so the
original mutex is replaced by locks around the actual io.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
[guenter.roeck@ericsson.com: Added value range check to key_at_index_store()]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Cc: stable@kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch add support for the MacBookAir3,1 and MacBookAir3,2 to the
applesmc driver.
[rydberg@euromail.se: minor cleanup]
Cc: stable@kernel.org
Signed-off-by: Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The owner field was removed from struct attribute in
6fd69dc578, so don't assign it anymore.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Allow 1 as a valid div value as specified in the ADM1026 datasheet.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prevent setting fan_div from stomping on other fans that share the
same I2C register.
Signed-off-by: Gabriele Gorla <gorlik@penguintown.net>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The manual fan speed control logic of the IT8721F is much different
from what older devices had. Update the code to properly support that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This commit fixes the following compile warnings.
From v2.6.37-rc2/m68k/m68k-allmodconfig, v2.6.37-rc2/powerpc/powerpc-randconfig:
drivers/hwmon/lis3lv02d_i2c.c:222: warning: 'lis3_i2c_runtime_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:231: warning: 'lis3_i2c_runtime_resume' defined but not used
Seen if CONFIG_PM_RUNTIME is not set.
From v2.6.37-rc2/sh4/sh-allyesconfig:
drivers/hwmon/lis3lv02d_i2c.c:191: warning: 'lis3lv02d_i2c_suspend' defined but not used
drivers/hwmon/lis3lv02d_i2c.c:201: warning: 'lis3lv02d_i2c_resume' defined but not used
Seen if CONFIG_PM is set but CONFIG_PM_SLEEP is not.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the following compile warning.
drivers/hwmon/i5k_amb.c:500: warning: 'i5k_amb_ids' defined but not used
The warning is seen if the driver is built into the kernel (not as module).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current implementation, the sysfs entries is not removed before return -ENODEV.
Creating the sysfs attribute should be the last thing done by the function,
after all the rest has been successful.
Otherwise there is a small window during which user-space can access the attribute
but the driver isn't ready to deal with the requests.
Fix it by moving sysfs_create_group to be the last thing done by the function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Return proper error if i2c_check_functionality reports
the adapter does not support the capability we need.
Also remove unneeded initialization for err variable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.
Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Hans de Goede
Guenter Roeck
Ian Dobson
per.dalen@appeartv.com
Mark Brown
stigge@antcom.de
Grant Likely
axel lin
Jan Beulich
Clemens Ladisch
Dirk Eibach
Kalhan Trisal
Luca Tettamanti
Henrik Rydberg
Juerg Haefliger
Jekyll Lai
Jean Delvare
Joe Perches
Steven Hardy
Urs Fleisch
Davide Rizzo
Edgar Hucek
Maurus Cuelenaere
Linus Torvalds
Ira W. Snyder
Gabriele Gorla
Hans J. Koch