Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.
It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.
Fixes: 76723bca28 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.
Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to configure TC map 0 for VSI 391
This reverts commit 3d2504663c.
Fixes: 3d2504663c (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 2afeec08ab.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 1f2565780e.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().
Fixes: d7df09f5e7 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().
This resolves the issue of garbage values output when querying with self
test via ethtool.
before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 1768697188
Health Test 758528120
Loopback Test 3288687
after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 0
Health Test 0
Loopback Test 0
Fixes: 7990b1b5e8 ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.
Fix by returning error in case flow is matching on tunnel key.
Fixes: 72046a91d1 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.
Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.
Fixes: f828ca6a2f ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.
Fixes: 0a1498ebfa ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.
Fixes: 806401c20a ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.
Fixes: 03a9d11e6e ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This kind of action is not supported by firmware and generates a
syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fixes: d7e75a325c ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Fixes: 1182f36593 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.
Fixes: bb64143eee ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.
Fixes: 465e7baab6 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.
Fixes: 9a99c8f125 ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.
Fixes: 92ab1eb392 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.
This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.
Fixes: f79a609ea6 ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.
This patch replaces the hard-coded threshold with a dynamic value.
Fixes: 1c58651412 ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When adding a rule with 32 destinations, we hit the following out-of-band
access issue:
BUG: KASAN: slab-out-of-bounds in mlx5_cmd_dr_create_fte+0x18ee/0x1e70
This patch fixes the issue by both increasing the allocated buffers to
accommodate for the needed actions and by checking the number of actions
to prevent this issue when a rule with too many actions is provided.
Fixes: 1ffd498901 ("net/mlx5: DR, Increase supported num of actions to 32")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:
rcu: INFO: rcu_sched self-detected stall on CPU
To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.
Fixes: 29cf8febd1 ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add the upcoming BlueField-4 and ConnectX-8 device IDs.
Fixes: 2e9d3e83ab ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.
It is caused by below procedures in the driver:
1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule
After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.
Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.
Fixes: 334c424147 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.
PHY detect failure started to show after commit 7590fc6f80 ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.
10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes: 3c4153394e ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db76 ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped. This is correct because a FW reset during
ifdown will clear these register mappings. If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.
But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.
Fixes: 8cc95ceb70 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes: 7d2837dd7a ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b9 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.
After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.
Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.
Fixes: b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-18
This series contains updates to ice driver only.
Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.
Michal removes accidental unconditional setting of l4 port filtering
flag.
Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.
Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.
In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.
So set it to -1.
Fixes: 20cce88650 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ldo->phy_type_low |= ((u64)buf << (i * 16));
~~~~~~~~~~~~~~~~~ ^
When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv. So initialize.
Fixes: ea78ce4dab ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
is a garbage value
set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64(). This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c503e63200 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Accidentally filter flag for none encapsulated l4 port field is always
set. Even if user wants to add encapsulated l4 port field.
Remove this unnecessary flag setting.
Fixes: 9e300987d4 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In switchdev mode, slow-path rules need to match all protocols, in order
to correctly redirect unfiltered or missed packets to the uplink. To set
this up for the virtual function to uplink flow, the rule that redirects
packets to the control VSI must have the tunnel type set to
ICE_SW_TUN_AND_NON_TUN. As a result of that new tunnel type being set,
ice_get_compat_fv_bitmap will select ICE_PROF_ALL. At that point all
profiles would be selected for this rule, resulting in the desired
behavior. Without this change slow-path would not work with
tunnel protocols.
Fixes: 8b032a55c1 ("ice: low level support for tunnels")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f0 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().
This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_sendmsg() |
ax25_queue_xmit() |
... |
sp_xmit() |
sp_encaps() | sixpack_close()
sp_xmit_on_air() | del_timer_sync(&sp->tx_t)
mod_timer(&sp->tx_t,...) | ...
| unregister_netdev()
| ...
(wait a while) | tty_release()
| tty_release_struct()
| release_tty()
sp_xmit_on_air() | tty_kref_put(tty_struct) //FREE
pty_write(tty_struct) //USE | ...
The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
...
queue_work_on+0x3f/0x50
pty_write+0xcd/0xe0pty_write+0xcd/0xe0
sp_xmit_on_air+0xb2/0x1f0
call_timer_fn+0x28/0x150
__run_timers.part.0+0x3c2/0x470
run_timer_softirq+0x3b/0x80
__do_softirq+0xf1/0x380
...
This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices,
avoid FW assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Nrzq
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes: ff59c4563a ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mauri Sandberg
Mateusz Palczewski
Manish Chopra
Marek Marczykowski-Górecki
Gal Pressman
Lama Kayal
Maor Dickman
Roi Dayan
Tariq Toukan
Maor Gottlieb
Chris Mi
Ariel Levkovich
Maher Sanalla
Yevgeny Kliteynik
Meir Lichtinger
Heyi Guo
Sukadev Bhattiprolu
Baruch Siach
Kalesh AP
Michael Chan
Pavan Chebbi
Somnath Kotur
Svenning Sørensen
David S. Miller
Christophe JAILLET
Jeremy Linton
Tom Rix
Jacob Keller
Michal Swiatkowski
Wojciech Drewek
Xiaoke Wang
Oliver Neukum
Duoming Zhou
Linus Torvalds
Zhang Changzhong