In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.
In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.
Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf1a
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.
Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.
The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed
mode switch")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
mmc_test_check_result_async() requires that struct mmc_async_req is
contained within struct mmc_test_async_req. Fix the "Commands during
non-blocking write" tests so that is the case.
Fixes: 4bbb9aac9a ("mmc: mmc_test: Add tests for sending commands during transfer")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang. Fix by
only clearing the data command for data interrupts that are expected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD line reset during an ongoing data transfer can cause the data transfer
to hang. Fix by delaying the reset until the data transfer is finished.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This basicly reverts commit e534f3e9 (staging:nvec: Introduce the use of
the managed version of kzalloc). Serio struct should never by managed
because it is refcounted. Doing so will lead to a double free oops on module
remove.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Fixes: e534f3e942 ("staging:nvec: Introduce the use of the managed version of kzalloc")
Cc: stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 36b30d6138.
This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.
Commit ec6184b1c7 changed the way
auto-detection is performed on ports marked as pass through and made the
issue apparent.
A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).
Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Fixes: 36b30d6138 ("staging: nvec: ps2: change serio type to passthrough")
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.
To prevent this from happening just let every party do its part of the
job.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the device reference taken by of_find_device_by_node()
before returning from arche_platform_change_state().
Note that this code is expected to be removed, but let's fix up the leak
nonetheless.
Fixes: 886aba558b ("greybus: arche-platform: Export fn to allow...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <hvaibhav.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`ni_tio_clock_period_ps()` used to return the clock period in
picoseconds, and had a `BUG()` call for invalid cases. It was changed
to pass the clock period back via a pointer parameter and return an
error for the invalid cases. Unfortunately the code to handle
user-specified clock sources with user-specified clock period is still
returning the clock period the old way, which can lead to the caller not
getting the clock period, or seeing an unexpected error. Fix it by
passing the clock period via the pointer parameter and returning `0`.
Fixes: b42ca86ad6 ("staging: comedi: ni_tio: remove BUG() checks for ni_tio_get_clock_src()")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Early commit 30ca5cb63c ("staging: sm750fb: change definition of
PANEL_PLANE_TL fields") and 27b047bbe1 ("staging: sm750fb: change
definition of PANEL_PLANE_BR fields") modify the register bit fields
definitions. But the modifications are wrong, because the bit mask of
"bit field 10:0" is not 0xeff, but 0x7ff. The wrong definition bugs
makes display very strange.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
variable struct usb_cdc_parsed_header h may be used
uninitialized in acm_probe.
In kernel 4.8.
/* handle quirks deadly to normal probing*/
if (quirks == NO_UNION_NORMAL)
...
goto skip_normal_probe;
}
we bypass call to
cdc_parse_cdc_header(&h, intf, buffer, buflen);
but later use h in
if (h.usb_cdc_country_functional_desc) { /* export the country data */
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reported-by: Victor Sologoubov <victor0@rambler.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never seen XHCI auto handoff working on TI and RENESAS cards.
Eventually, we force handoff. This code forces the handoff
unconditionally. It saves 5 seconds boot time for each card.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This suppresses printing the error message "failed to get phy" in the
kernel log when the error is -EPROBE_DEFER. This prevents usless noise
in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phy fixes:
*) Add a empty function for phy_reset when CONFIG_GENERIC_PHY is not set
*) change the phy lookup table for da8xx-usb to match it with the name
present in the board configuraion file (used for non-dt boot)
*) Fix incorrect programming sequence in w.r.t deassert of phy_rst
in phy-rockchip-pcie
*) Fix to avoid NULL pointer dereferencing error in sun4i phy
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uTAz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.9 -rc
phy fixes:
*) Add a empty function for phy_reset when CONFIG_GENERIC_PHY is not set
*) change the phy lookup table for da8xx-usb to match it with the name
present in the board configuraion file (used for non-dt boot)
*) Fix incorrect programming sequence in w.r.t deassert of phy_rst
in phy-rockchip-pcie
*) Fix to avoid NULL pointer dereferencing error in sun4i phy
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Interestingly scale related fixes for accelerometers at both ends of
the range. Obviously more varied devices turning up than we've seen before!
* ad5933
- fix an uninitialized value in a return case that is winding up GCC.
* hid sensors
- missing pm function prevents hid rotations sensors from working on newer
ISH hubs (works by luck on older ones)
- increase of scale precision needed to fix a case where on a yoga 260
the reported scale is 0 (presumably a high precision but very low g sensor).
* st_sensors
- fix an issue seen with the hs3lis331dl where the range is much greater
than previous devices (100's of g) and hence the per bit scale is greater
than 1.
-----BEGIN PGP SIGNATURE-----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=KcFP
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Second set of IIO fixes for the 4.9 cycle.
Interestingly scale related fixes for accelerometers at both ends of
the range. Obviously more varied devices turning up than we've seen before!
* ad5933
- fix an uninitialized value in a return case that is winding up GCC.
* hid sensors
- missing pm function prevents hid rotations sensors from working on newer
ISH hubs (works by luck on older ones)
- increase of scale precision needed to fix a case where on a yoga 260
the reported scale is 0 (presumably a high precision but very low g sensor).
* st_sensors
- fix an issue seen with the hs3lis331dl where the range is much greater
than previous devices (100's of g) and hence the per bit scale is greater
than 1.
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add reset-names property for binding dw-mmc controller.
It might be used together with "reset" property.
- Note: It must be "reset" as name.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes for some msm issues
* 'msm-fixes-4.9' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Fix error handling crashes seen when VRAM allocation fails
drm/msm/mdp5: 8x16 actually has 8 mixer stages
drm/msm/mdp5: no scaling support on RGBn pipes for 8x16
drm/msm/mdp5: handle non-fullscreen base plane case
drm/msm: Set CLK_IGNORE_UNUSED flag for PLL clocks
drm/msm/dsi: Queue HPD helper work in attach/detach callbacks
A few more fixes for 4.9.
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add some error handling to amdgpu_init v2
drm/amd: fix scheduler fence teardown order v2
drm/amd/powerplay: don't succeed in getters if fan is missing
drm/amdgpu: make sure ddc_bus is valid in connector unregister
drm/radeon: Fix kernel panic on shutdown
drm/amdgpu: disable runtime pm in certain cases
drm/radeon: disable runtime pm in certain cases
drm/amdgpu: add support for new smc firmware on iceland
drm/amdgpu: add support for new smc firmware on tonga
'blk_mq_alloc_request()' returns an error pointer in case of error, not
NULL. So test it with IS_ERR.
Fixes: fd8383fd88 ("nbd: convert to blkmq")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
Starting from 4.9-rc1 kernel, I started noticing some test failures
of sendfile(2) and splice(2) (sendfile0N and splice01 from LTP) when
testing on sub-page block size filesystems (tested both XFS and
ext4), these syscalls start to return EIO in the tests. e.g.
sendfile02 1 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 26, got: -1
sendfile02 2 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 24, got: -1
sendfile02 3 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 22, got: -1
sendfile02 4 TFAIL : sendfile02.c:133: sendfile(2) failed to return expected value, expected: 20, got: -1
This is because that in sub-page block size cases, we don't need the
whole page to be uptodate, only the part we care about is uptodate
is OK (if fs has ->is_partially_uptodate defined). But
page_cache_pipe_buf_confirm() doesn't have the ability to check the
partially-uptodate case, it needs the whole page to be uptodate. So
it returns EIO in this case.
This is a regression introduced by commit 82c156f853 ("switch
generic_file_splice_read() to use of ->read_iter()"). Prior to the
change, generic_file_splice_read() doesn't allow partially-uptodate
page either, so it worked fine.
Fix it by skipping the partially-uptodate check if we're working on
a pipe in do_generic_file_read(), so we read the whole page from
disk as long as the page is not uptodate.
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull i2c fix from Wolfram Sang:
"A bugfix for the I2C core fixing a (rare) race condition"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: fix NULL pointer dereference under race condition
Commit efd9e03fac ("arm64: Use static keys for CPU features")
introduced support for static keys in asm/cpufeature.h, including
linux/jump_label.h. When CC_HAVE_ASM_GOTO is not defined, this causes a
circular dependency via linux/atomic.h, asm/lse.h and asm/cpufeature.h.
This patch moves the capability macros out out of asm/cpufeature.h into
a separate asm/cpucaps.h and modifies some of the #includes accordingly.
Fixes: efd9e03fac ("arm64: Use static keys for CPU features")
Reported-by: Artem Savkov <asavkov@redhat.com>
Tested-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull stack vmap fixups from Thomas Gleixner:
"Two small patches related to sched_show_task():
- make sure to hold a reference on the task stack while accessing it
- remove the thread_saved_pc printout
.. and add a sanity check into release_task_stack() to catch problems
with task stack references"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Remove pointless printout in sched_show_task()
sched/core: Fix oops in sched_show_task()
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fork: Add task stack refcounting sanity check and prevent premature task stack freeing
Pull MD fixes from Shaohua Li:
"There are several bug fixes queued:
- fix raid5-cache recovery bugs
- fix discard IO error handling for raid1/10
- fix array sync writes bogus position to superblock
- fix IO error handling for raid array with external metadata"
* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: be careful not lot leak internal curr_resync value into metadata. -- (all)
raid1: handle read error also in readonly mode
raid5-cache: correct condition for empty metadata write
md: report 'write_pending' state when array in sync
md/raid5: write an empty meta-block when creating log super-block
md/raid5: initialize next_checkpoint field before use
RAID10: ignore discard error
RAID1: ignore discard error
Two more important data integrity fixes related to RAID device drivers which
wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID path and a
memory leak in the scsi_debug driver
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYHd5nAAoJEAVr7HOZEZN4BeIP/RmOchL8Xdm2GObAJYeeC5Jv
7jYqcjsV3LHz8ubebRk/GmrcXVmF52VJ0nc6IgcoAhG44kaY99kapah7wDioMci4
DC1m9twxQMfclEjk+8nL59iC4HR+A5TlMRnXf3XRTQ399w9KxGe1jGS2/OIOYpPd
goeQdSfSLxQX87c4eZldotQDY/9NUDe/O0Af3JboX5ySCDnqKiu+xqhE+kXKY7oY
bfsBurF875bER63YCeRIjmc/iO/klYGcm/7wsEJfxDZerY2/Sr6LaAd+bcComWX2
YAcoTwOGHwbjhKUbkHGjsQIaT+VFNOCDfXF1Bm37WTF5/AFiBfHRgQEClXm5I6kD
aRfcwfXeb6jDvUujCksIngSCeQc6/3np9gvmBV6hjKEmn07ny8j7vsDbI2gUL6rs
IVzMrFUw8O/InyooJD9CubnV7cgKnU+3/WIw3J92UudiEDRJSpCiBszoKL7JnOeA
aAeUl3hhQBr50w0nLCFcm65PnHjCY/4VuJ7ZXF6Z1e6y+yd81zrbzHYC4rb9sFsa
3KJ4UgIajhC0t5FxDbwFfOj/b0WhLzqJeMrOnTyI+mrjpHWexNW+iIMw6qRi6yv9
YuL9XvaaRblnmxOEma3A3xiTCQ6mFl4yYcMa4ppBlDgbTZSJff4kRB+Nma/qw1+v
VrKlOiKXC5wYp8jPlRwT
=xrlP
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
- Add missing input validation to the firewire-net driver.
Invalid IP-over-1394 encapsulation headers could trigger
buffer overflows (CVE 2016-8633).
- IP-over-1394 link fragmentation headers were read and written
incorrectly, breaking fragmented RX/TX with other OS's stacks.
-----BEGIN PGP SIGNATURE-----
iQI3BAABCAAhBQJYHgSgGhxzdGVmYW5yQHM1cjYuaW4tYmVybGluLmRlAAoJEHnz
b7JUXXnQFGIP/AvXrsLFgO8vOZd967145Jz0FydmwRBsX1F90xugFIxJI8kRQSN4
MQ/WHPaHl55LqX88VrxDTfN04TAtb243CDPXDnMN6rEzaSY4O7J6JO/zaUKMGyaW
rocX3s3uufIqk/GXDk2+I0Ze6xHynbWEPaoDh0rHYkJcD0NHHi9SJPFZf8RnCx3g
s7GAiU5V9o1SZydY9dCGo66Zl3JSujOsxpbVllT2ux+FWRReea5+O9ntWpPcW+E0
Elc9v7Nt3BcOEDXrVYg8UIIX6RCt8IBDCaF6D7n8JrhU/ag+OH8+KondktU5P+BI
MXcsm92UbM+/739RC7V6JbDSodUn1DisoOTyNmH58ZZerKWWt+7E27WXWuRu9ch7
rBra6pcOhkhO9sHkrwf3DlP9nubAfVbznVxZFOI4O96fnpn284J0RX8brsMOeHcF
iPAIpGc5PLyvyhczZSfokKj9S4kUvbwhNwCnHs32ttdrGSHRIVFKHsipsFFtcts2
K7QAN9mxWtBeP8i3gd5tJO8FT7tvg4Ixtt/BzpsFpxaYk9b/k2RnrSt4b4/0mC2q
fQ6urSQalvffmbU9eMm78NbaFV26s217gZHqqD++tAVLLgkwRaC2k/MucOJJz4xb
5PYoGLDfCusReBP/MYdpqOhAUEBeeZ03IQT7gaGGDQ27x8k1UIpB57Sk
=PxAL
-----END PGP SIGNATURE-----
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull FireWire (IEEE 1394) fixes from Stefan Richter:
- add missing input validation to the firewire-net driver. Invalid
IP-over-1394 encapsulation headers could trigger buffer overflows
(CVE 2016-8633).
- IP-over-1394 link fragmentation headers were read and written
incorrectly, breaking fragmented RX/TX with other OS's stacks.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: net: fix fragmented datagram_size off-by-one
firewire: net: guard against rx buffer overflows
-----BEGIN PGP SIGNATURE-----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=MRLH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYHO/8AAoJEFmIoMA60/r8z/0P/1JT1lHNtDgC3RBr5NRy6x+K
9xAfxeHJjxS/6YbFCBgPlzQJBzZMiSHptb/Y44Cqpr8Gz5WWnn18gbdMoBGQFc6k
n7iVvEGlvf2YR3CulqdsUH3/B2hDjNbM45HT2Rwd1agq+qku6nMpXdUix+z7TNEg
Tht/a8XAs77/XOl/uhGSCy5hvGKErcLNrZ1qFWmiUJEsFFgzSx3eqtx2MNJSiJyv
/F9dzDIgNKAOdOv34hYndE+VLwyFAwqzvIgB5J4oLL23+FzRW68yvQgmt45cogTF
NA4uFCfnaSK2Dy7qFOfevRE2AfQcSSfvvsGukQQaFoKyY8Jb6Z8w6WWO0P/RBQsY
ZvmP10JfyjQ5z2SSAMcVNDXR2dL58zc6kuGZISUToX22mMSUsmFMhLq2350657C9
0A8BkfO86z4EfgmO8aiBfgE7A6RrCR6yfouQTTGJ91COYEG60D/mPhlhtkmHE4yd
3tqmBSEw11yv92OLU4DdoXFA7Cbm7DElEk6fPcw5TbbWCwbToTHNo/jHbe+0+Esy
je5AFZe8IIuBHVkN3tcsoaRw2KKCtnBrLbfdyLME6KDXj7eZMg3WWoU0E5uwzIO3
jLOSCBb2dtqrJmiE4sNiYob8wI+jOLsC/XHHczYWnIzLiYyvYeZP6cBhHao0KCLD
/ao0YY6m3eUtwSJZbU2q
=n738
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix for a Qualcomm driver issue that causes a use-before-set crash
- fix for DesignWare iATU unroll support that causes external aborts
when enabling the host bridge
* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
* MAINTAINERS updates to reflect some new maintainers/submaintainers -- we
have some great volunteers who've been developing and reviewing already.
We're going to try a group maintainership model, so eventually you'll
probably see pull requests from people besides me.
* NAND fixes from Boris:
"""
Three simple fixes:
- the first one is fixing a non-critical bug in the gpmi driver
- the second one is fixing a bug in the 'automatic NAND timings
selection' feature introduced in 4.9-rc1
- the last one is fixing a false positive uninitialized-var warning
"""
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7VFh
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates to reflect some new maintainers/submaintainers.
We have some great volunteers who've been developing and reviewing
already. We're going to try a group maintainership model, so
eventually you'll probably see pull requests from people besides me.
- NAND fixes from Boris:
"Three simple fixes:
- fix a non-critical bug in the gpmi driver
- fix a bug in the 'automatic NAND timings selection' feature
introduced in 4.9-rc1
- fix a false positive uninitialized-var warning"
* tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd:
mtd: mtk: avoid warning in mtk_ecc_encode
mtd: nand: Fix data interface configuration logic
mtd: nand: gpmi: disable the clocks on errors
MAINTAINERS: add more people to the MTD maintainer team
MAINTAINERS: add a maintainer for the SPI NOR subsystem
While testing, it was observed that on some platforms the scale value
from iio sysfs for gyroscope is always 0 (E.g. Yoga 260). This results
in the final angular velocity component values to be zeros.
This is caused by insufficient precision of scale value displayed in sysfs.
If the precision is changed to nano from current micro, then this is
sufficient to display the scale value on this platform.
Since this can be a problem for all other HID sensors, increase scale
precision of all HID sensors to nano from current micro.
Results on Yoga 260:
name scale before scale now
--------------------------------------------
gyro_3d 0.000000 0.000000174
als 0.001000 0.001000000
magn_3d 0.000001 0.000001000
accel_3d 0.000009 0.000009806
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fix makes newer ISH hubs work. Previous ones worked by lucky
coincidence.
Rotation sensor function does not work due to miss PM function.
Add common hid sensor iio pm function for rotation sensor.
Further clarification from Srinivas:
If CONFIG_PM is not defined, then this prevents this sensor to
function. So above commit caused this.
This sensor was supposed to be always on to trigger wake up in prior
external hubs. But with the new ISH hub this is not the case.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Fixes: 2b89635e9a ("iio: hid_sensor_hub: Common PM functions")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Fix a nasty file descriptor leak when getting line handles.
- A fix for a cleanup that seemed innocent but created a problem
for drivers instantiating several gpiochips for one single
OF node.
- Fix a unpredictable problem using irq_domain_simple() in the
mvebu driver by converting it to a lineas irqdomain.
-----BEGIN PGP SIGNATURE-----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=QmJl
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.9 series:
- Fix a nasty file descriptor leak when getting line handles.
- A fix for a cleanup that seemed innocent but created a problem for
drivers instantiating several gpiochips for one single OF node.
- Fix a unpredictable problem using irq_domain_simple() in the mvebu
driver by converting it to a lineas irqdomain"
* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/mvebu: Use irq_domain_add_linear
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak
User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.
But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.
This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allwinner SoC's PHY 0, when used as OTG controller, have no pmu part.
The code that poke some unknown bit of PMU for H3/A64 didn't check
the PHY, and will cause kernel oops when PHY 0 is used.
This patch will check whether the pmu is not NULL before poking.
Fixes: b3e0d141ca (phy: sun4i: add support for A64 usb phy)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The deassert of phy_rst from exit callback is incorrect as when
doing phy_exit, we expect the phy_rst is on asserted state which was
done by power_off callback, but not deasserted state. Meanwhile when
disabling clk_pciephy_ref, the assert/deassert signal can't actually
take effect on the phy. So let's fix it anyway.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The ohci device name has changed in the board configuraion files,
hence, change the phy lookup table to match the new name.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a dummy function for phy_reset in case the CONFIG_GENERIC_PHY
is disabled.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Ulf Hansson
Adrian Hunter
Marc Dietrich
Paul Fertser
Johan Hovold
Ian Abbott
Andrew Jeffery
Huacai Chen
Oliver Neukum
Babu Moger
Kirill Esipov
David Lechner
Greg Kroah-Hartman
Jaehoon Chung
Dave Airlie
Christophe JAILLET
Eryu Guan
Guenter Roeck
Linus Torvalds
Catalin Marinas
Song Hongyan
Ooi, Joyce
Srinivas Pandruvada
Even Xu
Icenowy Zheng
Shawn Lin
Axel Haslam
Randy Li