Eliminate the following coccicheck warning:
./drivers/hid/i2c-hid/i2c-hid-core.c:357:56-57: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All I2C communications in the driver use driver-private buffers that are
DMA-safe, so mark them as such.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can stop defining a union for HID descriptor data as we now only access
individual members of it by names and using proper types instead of
accessing by offset from the beginning of the data structure.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is better to use helpers to do endian conversion as it documents
and draws attention to it, and might be a bit more performant as
well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Explicitly prepare command for i2c_hid_get_report() which makes the logic
clearer and allows us to get rid of __i2c_hid_command() and related command
definitions.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will allow us to drop i2c_hid_command() wrapper and get close
to removing __i2c_hid_command().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Another case where creating a dedicated helper allows for cleaner code that
shows exactly what communication happens with the device when toggling its
power.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Handling simple read of device registers in __i2c_hid_command() makes it
too complicated and the need of special handling for the HID descriptor
register adds even more complexity. Instead, let's create simple
i2c_hid_read_register() helper on base of i2c_hid_xfer() and use it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of relying on __i2c_hid_command() that tries to handle all
commands and because of that is very complicated, let's define a
new dumb helper i2c_hid_xfer() that actually transfers (write and
read) data, and use it when sending and setting reports. By doing
that we can save on number of copy operations we have to execute,
and make logic of sending reports much clearer.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Reset" is the only command that needs to wait for interrupt from
the device before continuing, so let's factor our waiting logic from
__i2c_hid_command() to make it simpler.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The main object in the driver is struct i2c_hid so it makes more sense
to pass it around instead of passing i2c_client and then fetching
i2c_hid associated with it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Internally kernel prepends all report buffers, for both numbered and
unnumbered reports, with report ID, therefore to properly handle unnumbered
reports we should prepend it ourselves.
For the same reason we should skip the first byte of the buffer when
calling i2c_hid_set_or_send_report() which then will take care of properly
formatting the transfer buffer based on its separate report ID argument
along with report payload.
[jkosina@suse.cz: finalize trimmed sentence in changelog as spotted by Benjamin]
Fixes: 9b5a9ae885 ("HID: i2c-hid: implement ll_driver transport-layer callbacks")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Special handling of numbered reports with IDs of 15 and above is only
needed when executing what HID-I2C spec is calling "Class Specific
Requests", and not when simply sending output reports.
Additionally, our mangling of report ID in i2c_hid_set_or_send_report()
resulted in incorrect report ID being written into SET_REPORT command
payload.
To solve it let's move all the report ID manipulation into
__i2c_hid_command() where we form the command data structure.
Signed-off-by: Angela Czubak <acz@semihalf.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I'm was on the receiving end of a lockdep splat from this driver and after
scratching my head I couldn't be entirely sure it was a false positive
given we would also have to think about whether the regulator locking is
safe (since the notifier is called whilst holding regulator locks which
are also needed for regulator_is_enabled() ).
Regardless of whether it is a real bug or not, the mutex isn't needed.
We can use reference counting tricks instead to avoid races with the
notifier calls.
The observed splat follows:
------------------------------------------------------
kworker/u16:3/127 is trying to acquire lock:
ffff00008021fb20 (&ihid_goodix->regulator_mutex){+.+.}-{4:4}, at: ihid_goodix_vdd_notify+0x30/0x94
but task is already holding lock:
ffff0000835c60c0 (&(&rdev->notifier)->rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x30/0x70
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(&rdev->notifier)->rwsem){++++}-{4:4}:
down_write+0x68/0x8c
blocking_notifier_chain_register+0x54/0x70
regulator_register_notifier+0x1c/0x24
devm_regulator_register_notifier+0x58/0x98
i2c_hid_of_goodix_probe+0xdc/0x158
i2c_device_probe+0x25d/0x270
really_probe+0x174/0x2cc
__driver_probe_device+0xc0/0xd8
driver_probe_device+0x50/0xe4
__device_attach_driver+0xa8/0xc0
bus_for_each_drv+0x9c/0xc0
__device_attach_async_helper+0x6c/0xbc
async_run_entry_fn+0x38/0x100
process_one_work+0x294/0x438
worker_thread+0x180/0x258
kthread+0x120/0x130
ret_from_fork+0x10/0x20
-> #0 (&ihid_goodix->regulator_mutex){+.+.}-{4:4}:
__lock_acquire+0xd24/0xfe8
lock_acquire+0x288/0x2f4
__mutex_lock+0xa0/0x338
mutex_lock_nested+0x3c/0x5c
ihid_goodix_vdd_notify+0x30/0x94
notifier_call_chain+0x6c/0x8c
blocking_notifier_call_chain+0x48/0x70
_notifier_call_chain.isra.0+0x18/0x20
_regulator_enable+0xc0/0x178
regulator_enable+0x40/0x7c
goodix_i2c_hid_power_up+0x18/0x20
i2c_hid_core_power_up.isra.0+0x1c/0x2c
i2c_hid_core_probe+0xd8/0x3d4
i2c_hid_of_goodix_probe+0x14c/0x158
i2c_device_probe+0x25c/0x270
really_probe+0x174/0x2cc
__driver_probe_device+0xc0/0xd8
driver_probe_device+0x50/0xe4
__device_attach_driver+0xa8/0xc0
bus_for_each_drv+0x9c/0xc0
__device_attach_async_helper+0x6c/0xbc
async_run_entry_fn+0x38/0x100
process_one_work+0x294/0x438
worker_thread+0x180/0x258
kthread+0x120/0x130
ret_from_fork+0x10/0x20
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&rdev->notifier)->rwsem);
lock(&ihid_goodix->regulator_mutex);
lock(&(&rdev->notifier)->rwsem);
lock(&ihid_goodix->regulator_mutex);
*** DEADLOCK ***
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Fixes: 18eeef46d3 ("HID: i2c-hid: goodix: Tie the reset line to true state of the regulator")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow the touchscreen-inverted-x/y device tree properties to control the
HID_QUIRK_X_INVERT/HID_QUIRK_Y_INVERT quirks for the hid-input device.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Rob Herring <robh@kernel.org>
[bentiss: silence checkpatch warnings]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20211208124045.61815-3-alistair@alistair23.me
There is a lot of duplication of code in the HID low level drivers.
Better have everything in one place so we can eventually extend it
in a generic way.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211202095334.14399-4-benjamin.tissoires@redhat.com
The i2c-hid driver generally supports wakeup, bit it currently
doesn't report wakeup events to the PM subsystem. Change that.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A quirk was recently added for Elan devices that has same device match
as an entry earlier in the list. The i2c_hid_lookup_quirk function will
always return the last match in the list, so the new entry shadows the
old entry. The quirk in the previous entry, I2C_HID_QUIRK_BOGUS_IRQ,
silenced a flood of messages which have reappeared in the 5.13 kernel.
This change moves the two quirk flags into the same entry.
Fixes: ca66a6770b (HID: i2c-hid: Skip ELAN power-on command after reset)
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 18eeef46d3 ("HID: i2c-hid: goodix: Tie the reset line to
true state of the regulator") I added a call to
regulator_register_notifier() but no call to unregister. That's a
bug. Let's use the devm variant to handle the unregistering.
Fixes: 18eeef46d3 ("HID: i2c-hid: goodix: Tie the reset line to true state of the regulator")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The regulator for the touchscreen could be:
* A dedicated regulator just for the touchscreen.
* A regulator shared with something else in the system.
* An always-on regulator.
How we want the "reset" line to behave depends a bit on which of those
three cases we're in. Currently the code is written with the
assumption that it has a dedicated regulator, but that's not really
guaranteed to be the case.
The problem we run into is that if we leave the touchscreen powered on
(because someone else is requesting the regulator or it's an always-on
regulator) and we assert reset then we apparently burn an extra 67 mW
of power. That's not great.
Let's instead tie the control of the reset line to the true state of
the regulator as reported by regulator notifiers. If we have an
always-on regulator our notifier will never be called. If we have a
shared regulator then our notifier will be called when the touchscreen
is truly turned on or truly turned off.
Using notifiers like this nicely handles all the cases without
resorting to hacks like pretending that there is no "reset" GPIO if we
have an always-on regulator.
NOTE: if the regulator is on a shared line it's still possible that
things could be a little off. Specifically, this case is not handled
even after this patch:
1. Suspend goodix (send "sleep", goodix stops requesting regulator on)
2. Other regulator user turns off (regulator fully turns off).
3. Goodix driver gets notified and asserts reset.
4. Other regulator user turns on.
5. Goodix driver gets notified and deasserts reset.
6. Nobody resumes goodix.
With that set of steps we'll have reset deasserted but we will have
lost the results of the I2C_HID_PWR_SLEEP from the suspend path. That
means we might be in higher power than we could be even if the goodix
driver thinks things are suspended. Presumably, however, we're still
in better shape than if we were asserting "reset" the whole time. If
somehow the above situation is actually affecting someone and we want
to do better we can deal with it when we have a real use case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
clang doesn't like printing a 32-bit integer using %hX format string:
drivers/hid/i2c-hid/i2c-hid-core.c:994:18: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~
drivers/hid/i2c-hid/i2c-hid-core.c:994:31: error: format specifies type 'unsigned short' but the argument has type '__u32' (aka 'unsigned int') [-Werror,-Wformat]
client->name, hid->vendor, hid->product);
^~~~~~~~~~~~
Use an explicit cast to truncate it to the low 16 bits instead.
Fixes: 9ee3e06610 ("HID: i2c-hid: override HID descriptors for certain devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For ELAN touchscreen, we found our boot code of IC was not flexible enough
to receive and handle this command.
Once the FW main code of our controller is crashed for some reason,
the controller could not be enumerated successfully to be recognized
by the system host. therefore, it lost touch functionality.
Add quirk for skip send power-on command after reset.
It will impact to ELAN touchscreen and touchpad on HID over I2C projects.
Fixes: 43b7029f47 ("HID: i2c-hid: Send power-on command after reset").
Cc: stable@vger.kernel.org
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The driver depends on ACPI, ACPI_PTR() resolution is always the same.
Otherwise a compiler may produce a warning.
That said, the rule of thumb either ugly ifdeffery with ACPI_PTR or
none should be used in a driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move static GUID variable out of the function and add a comment
how it looks like in the human readable representation.
While at it, include uuid.h since the guid_t type is defined in it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to the new style i2c-driver probe_new probe function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the ACPI companion and handle are retrieved and checked
a few times in different functions. Instead get ACPI companion only
once and reuse it everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ITE8568 EC on the Voyo Winpad A15 presents itself as an I2C-HID
attached keyboard and mouse (which seems to never send any events).
This needs the I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirk, otherwise we get
the following errors:
[ 3688.770850] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3694.915865] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3701.059717] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3707.205944] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3708.227940] i2c_hid i2c-ITE8568:00: can't add hid device: -61
[ 3708.236518] i2c_hid: probe of i2c-ITE8568:00 failed with error -61
Which leads to a significant boot delay.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Goodix i2c-hid touchscreens are mostly i2c-hid compliant but have some
special power sequencing requirements, including the need to drive a
reset line during the sequencing.
Let's use the new rejiggering of i2c-hid to support this with a thin
wrapper driver to support the first Goodix i2c-hid touchscreen:
GT7375P
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch rejiggers the i2c-hid code so that the OF (Open Firmware
aka Device Tree) and ACPI support is separated out a bit. The OF and
ACPI drivers are now separate modules that wrap the core module.
Essentially, what we're doing here:
* Make "power up" and "power down" a function that can be (optionally)
implemented by a given user of the i2c-hid core.
* The OF and ACPI modules are drivers on their own, so they implement
probe / remove / suspend / resume / shutdown. The core code
provides implementations that OF and ACPI can call into.
We'll organize this so that we now have 3 modules: the old i2c-hid
module becomes the "core" module and two new modules will depend on
it, handling probing the specific device.
As part of this work, we'll remove the i2c-hid "platform data"
concept since it's not needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Cc: stable@vger.kernel.org
Signed-off-by: Julian Sax <jsbc@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The i2c-hid driver would quietly fail to probe the i2c-hid sensor-hub
with an ACPI device-id of SMO91D0 every other boot.
Specifically, the i2c_smbus_read_byte() "Make sure there is something at
this address" check would fail every other boot.
It seems that the BIOS does not properly reset/power-cycle the device
leaving it in a confused state where it refuses to respond to i2c-xfers.
On boots where probing the device failed, the driver-core puts the device
in D3 after the probe-failure, which causes the probe to succeed the next
boot.
Putting the device in D3 from the shutdown-handler fixes the sensors not
working every other boot.
This has been tested on both a Lenovo Miix 2-10 and a Dell Venue 8 Pro 5830
both of which use an i2c-hid sensor-hub with an ACPI id of SMO91D0.
Note that it is safe to call acpi_device_set_power() with a NULL pointer
as first argument, so on none ACPI enumerated devices this change is a
no-op.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many laptops can be woken up from Suspend-to-Idle by touchpad. This is
also the default behavior on other OSes.
However, if touchpad and touchscreen contact to each other when lid is
closed, wakeup events can be triggered inadventertly.
So let's disable the wakeup by default, but enable the wakeup capability
so users can enable it at their own discretion.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix following warnings caused by mismatch bewteen function parameters
and comments.
drivers/hid/i2c-hid/i2c-hid-core.c:331: warning: Function parameter or member 'data_len' not described in 'i2c_hid_set_or_send_report'
drivers/hid/i2c-hid/i2c-hid-core.c:331: warning: Excess function parameter 'len' description in 'i2c_hid_set_or_send_report'
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding printouts to the i2c_hid_probe() function shows that it takes
quite some time. It used to take about 70 ms, but after commit
eef4016243 ("HID: i2c-hid: Always sleep 60ms after I2C_HID_PWR_ON
commands") it takes about 190 ms. This is not tons of time but it's
not trivial. Because we haven't yet specified that we'd prefer
asynchronous probe for this driver then, if the driver is builtin to
the kernel, we'll wait for this driver to finish before we start
probes for more drivers. Let's set the flag to enable asynchronous
for this driver so that other drivers aren't blocked from probing
until we finish.
Since this driver can be configured as a module and modules are
always asynchronously probed this is quite a safe change and will
benefit anyone who has a reason to build this driver into the kernel
instead of using it as a module.
[jkosina@suse.cz: drop spurious whitespace addition]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before this commit i2c_hid_parse() consists of the following steps:
1. Send power on cmd
2. usleep_range(1000, 5000)
3. Send reset cmd
4. Wait for reset to complete (device interrupt, or msleep(100))
5. Send power on cmd
6. Try to read HID descriptor
Notice how there is an usleep_range(1000, 5000) after the first power-on
command, but not after the second power-on command.
Testing has shown that at least on the BMAX Y13 laptop's i2c-hid touchpad,
not having a delay after the second power-on command causes the HID
descriptor to read as all zeros.
In case we hit this on other devices too, the descriptor being all zeros
can be recognized by the following message being logged many, many times:
hid-generic 0018:0911:5288.0002: unknown main item tag 0x0
At the same time as the BMAX Y13's touchpad issue was debugged,
Kai-Heng was working on debugging some issues with Goodix i2c-hid
touchpads. It turns out that these need a delay after a PWR_ON command
too, otherwise they stop working after a suspend/resume cycle.
According to Goodix a delay of minimal 60ms is needed.
Having multiple cases where we need a delay after sending the power-on
command, seems to indicate that we should always sleep after the power-on
command.
This commit fixes the mentioned issues by moving the existing 1ms sleep to
the i2c_hid_set_power() function and changing it to a 60ms sleep.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208247
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-and-tested-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- linked list race condition fix in hid-steam driver from Rodrigo Rivas
Costa
- assorted deviceID-specific quirks and other small cosmetic cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: avoid repeated "multiplier = " log messages
HID: logitech: Use HIDPP_RECEIVER_INDEX instead of 0xff
HID: quirks: Ignore Simply Automated UPB PIM
HID: apple: Disable Fn-key key-re-mapping on clone keyboards
MAINTAINERS: update uhid and hid-wiimote entry
HID: steam: fixes race in handling device list.
HID: magicmouse: do not set up autorepeat
HID: alps: support devices with report id 2
HID: quirks: Always poll Obins Anne Pro 2 keyboard
HID: i2c-hid: add Mediacom FlexBook edge13 to descriptor override
The Mediacom FlexBook edge13 uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Signed-off-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Cc: stable@vger.kernel.org
Signed-off-by: Julian Sax <jsbc@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On the Dell XPS 9570, the Synaptics SYNA2393 touchpad generates spurious
interrupts after resuming from suspend until it receives some input or
is reset. Add it to the quirk I2C_HID_QUIRK_RESET_ON_RESUME so that it
is reset when resuming from suspend.
More information about the bug can be found in this mailing list
discussion: https://www.spinics.net/lists/linux-input/msg59530.html
Signed-off-by: Daniel Playfair Cal <daniel.playfair.cal@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Surfbook E11B uses the SIPODEV SP1064 touchpad, which does not supply
descriptors, so it has to be added to the override list.
BugLink: https://bugs.launchpad.net/bugs/1858299
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Jiri Kosina
Yang Li
Dmitry Torokhov
Angela Czubak
Daniel Thompson
Alistair Francis
Benjamin Tissoires
Matthias Kaehlcke
Jim Broadus
Douglas Anderson
Arnd Bergmann
Johnny Chuang
Andy Shevchenko
Hans de Goede
Julian Sax
Coiby Xu
Kai-Heng Feng
Xiaofei Tan
Linus Torvalds
Federico Ricchiuto
Masahiro Yamada
Daniel Playfair Cal
Pavel Balan