md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The update of ->recovery_offset in sync_sbs is appropriate even then external
metadata is in use. However sync_sbs is only called when native
metadata is used.
So move that update in to the top of md_update_sb (which is the only
caller of sync_sbs) before the test on ->external.
This moves the update out of ->write_lock protection, but those fields
only need ->reconfig_mutex protection which they still have.
Also move the test on ->persistent up to where ->external is set as
for metadata update purposes they are the same.
Clear MD_CHANGE_DEVS and MD_CHANGE_CLEAN as they can only be confusing
if ->external is set or ->persistent isn't.
Finally move the update of ->utime down as it is only relevent (like
the ->events update) for native metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Enable discard support in the DM multipath target.
This discard support depends on a few discard-specific fixes to the
block layer's request stacking driver methods.
Discard requests are optional so don't allow a failed discard to trigger
path failures. If there is a real problem with a given path the
barriers associated with the discard (either before or after the
discard) will cause path failure. That said, unconditionally passing
discard failures up the stack is not ideal. This must be fixed once DM
has more information about the nature of the underlying storage failure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
The DM core will submit a discard bio to the stripe target for each
stripe in a striped DM device. The stripe target will determine
stripe-specific portions of the supplied bio to be remapped into
individual (at most 'num_discard_requests' extents). If a given
stripe-specific discard bio doesn't touch a particular stripe the bio
will be dropped.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Update __clone_and_map_discard to loop across all targets in a DM
device's table when it processes a discard bio. If a discard crosses a
target boundary it must be split accordingly.
Update __issue_target_requests and __issue_target_request to allow a
cloned discard bio to have a custom start sector and size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Optimize sector division: If the number of stripes is a power of two,
we can do shift and mask instead of division.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move sector to stripe translation into a function.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the error target respond to a discard request with a hard -EIO
rather than fail the request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the zero target silently drop a discard rather than fail the
request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split max_io_len_target_boundary out of max_io_len so that the discard
support can make use of it without duplicating max_io_len code.
Avoiding max_io_len's split_io logic enables DM's discard support to
submit the entire discard request to a target. But discards must still
be split on target boundaries.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename __flush_target to __issue_target_request now that it is used to
issue both flush and discard requests.
Introduce __issue_target_requests as a convenient wrapper to
__issue_target_request 'num_flush_requests' or 'num_discard_requests'
times per target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow discards to be passed through to linear mappings if at least one
underlying device supports it. Discards will be forwarded only to
devices that support them.
A target that supports discards should set num_discard_requests to
indicate how many times each discard request must be submitted to it.
Verify table's underlying devices support discards prior to setting the
associated DM device as capable of discards (via QUEUE_FLAG_DISCARD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allocate cipher strings indpendently of struct crypt_config and move
cipher parsing and allocation into a separate function to prepare for
supporting the cryptoapi format e.g. "xts(aes)".
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use just one label and reuse common destructor for crypt target.
Parse remaining argv arguments in logic order.
Also do not ignore error values from IV init and set key functions.
No functional change in this patch except changed return codes
based on above.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'target_request_nr' is a more generic name that reflects the fact that
it will be used for both flush and discard support.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This change unifies the various checks and finalization that occurs on a
table prior to use. By doing so, it allows table construction without
traversing the dm-ioctl interface.
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement merge method for the snapshot origin to improve read
performance.
Without merge method, dm asks the upper layers to submit smallest possible
bios --- one page. Submitting such small bios impacts performance negatively
when reading or writing the origin device.
Without this patch, CPU consumption when reading the origin on lvm on md-raid0
was 6 to 12%, with this patch, it drops to 1 to 4%.
Note: in my testing, it actually degraded performance in some settings, I
traced it to Maxtor disks having problems with > 512-sector requests.
Reducing the number of sectors to /sys/block/sd*/queue/max_sectors_kb to
256 fixed the read performance. I think we don't have to care about weird
disks that actually degrade performance because of large requests being
sent to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change bio-based mapped devices no longer to have a fully initialized
request_queue (request_fn, elevator, etc). This means bio-based DM
devices no longer register elevator sysfs attributes ('iosched/' tree
or 'scheduler' other than "none").
In contrast, a request-based DM device will continue to have a full
request_queue and will register elevator sysfs attributes. Therefore
a user can determine a DM device's type by checking if elevator sysfs
attributes exist.
First allocate a minimalist request_queue structure for a DM device
(needed for both bio and request-based DM).
Initialization of a full request_queue is deferred until it is known
that the DM device is request-based, at the end of the table load
sequence.
Factor DM device's request_queue initialization:
- common to both request-based and bio-based into dm_init_md_queue().
- specific to request-based into dm_init_request_based_queue().
The md->type_lock mutex is used to protect md->queue, in addition to
md->type, during table_load().
A DM device's first table_load will establish the immutable md->type.
But md->queue initialization, based on md->type, may fail at that time
(because blk_init_allocated_queue cannot allocate memory). Therefore
any subsequent table_load must (re)try dm_setup_md_queue independently of
establishing md->type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Determine whether a mapped device is bio-based or request-based when
loading its first (inactive) table and don't allow that to be changed
later.
This patch performs different device initialisation in each of the two
cases. (We don't think it's necessary to add code to support changing
between the two types.)
Allowed md->type transitions:
DM_TYPE_NONE to DM_TYPE_BIO_BASED
DM_TYPE_NONE to DM_TYPE_REQUEST_BASED
We now prevent table_load from replacing the inactive table with a
conflicting type of table even after an explicit table_clear.
Introduce 'type_lock' into the struct mapped_device to protect md->type
and to prepare for the next patch that will change the queue
initialization and allocate memory while md->type_lock is held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-ioctl.c | 15 +++++++++++++++
drivers/md/dm.c | 37 ++++++++++++++++++++++++++++++-------
drivers/md/dm.h | 5 +++++
include/linux/dm-ioctl.h | 4 ++--
4 files changed, 52 insertions(+), 9 deletions(-)
When processing barriers, skip the second flush if processing the bio
failed with -EOPNOTSUPP. This can happen with discard+barrier requests.
If the device doesn't support discard, there would be two useless
SYNCHRONIZE CACHE commands. The first dm_flush cannot be so easily
optimized out, so we leave it there.
Previously, -EOPNOTSUPP could be received in dec_pending only with empty
barriers and we ignored that error, assuming the device not supporting
cache flushes has cache always consistent. With the addition of discard
barriers, this -EOPNOTSUPP can also be generated by discards and we
must record it in md->barrier_error for process_barrier.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes hard-coded value for the size of a chunk that includes
disk header for persistent snapshot. It should be changed to existing
macro NUM_SNAPSHOT_HDR_CHUNKS instead of using hard-coded value 1.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm control device does not implement read/write, so it has no use for
seeking. Using no_llseek prevents falling back to default_llseek, which
requires the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch separates the device deletion code from dm_put()
to make sure the deletion happens in the process context.
By this patch, device deletion always occurs in an ioctl (process)
context and dm_put() can be called in interrupt context.
As a result, the request-based dm's bad dm_put() usage pointed out
by Mikulas below disappears.
http://marc.info/?l=dm-devel&m=126699981019735&w=2
Without this patch, I confirmed there is a case to crash the system:
dm_put() => dm_table_destroy() => vfree() => BUG_ON(in_interrupt())
Some more backgrounds and details:
In request-based dm, a device opener can remove a mapped_device
while the last request is still completing, because bios in the last
request complete first and then the device opener can close and remove
the mapped_device before the last request completes:
CPU0 CPU1
=================================================================
<<INTERRUPT>>
blk_end_request_all(clone_rq)
blk_update_request(clone_rq)
bio_endio(clone_bio) == end_clone_bio
blk_update_request(orig_rq)
bio_endio(orig_bio)
<<I/O completed>>
dm_blk_close()
dev_remove()
dm_put(md)
<<Free md>>
blk_finish_request(clone_rq)
....
dm_end_request(clone_rq)
free_rq_clone(clone_rq)
blk_end_request_all(orig_rq)
rq_completed(md)
So request-based dm used dm_get()/dm_put() to hold md for each I/O
until its request completion handling is fully done.
However, the final dm_put() can call the device deletion code which
must not be run in interrupt context and may cause kernel panic.
To solve the problem, this patch moves the device deletion code,
dm_destroy(), to predetermined places that is actually deleting
the mapped_device in ioctl (process) context, and changes dm_put()
just to decrement the reference count of the mapped_device.
By this change, dm_put() can be used in any context and the symmetric
model below is introduced:
dm_create(): create a mapped_device
dm_destroy(): destroy a mapped_device
dm_get(): increment the reference count of a mapped_device
dm_put(): decrement the reference count of a mapped_device
dm_destroy() waits for all references of the mapped_device to disappear,
then deletes the mapped_device.
dm_destroy() uses active waiting with msleep(1), since deleting
the mapped_device isn't performance-critical task.
And since at this point, nobody opens the mapped_device and no new
reference will be taken, the pending counts are just for racing
completing activity and will eventually decrease to zero.
For the unlikely case of the forced module unload, dm_destroy_immediate(),
which doesn't wait and forcibly deletes the mapped_device, is also
introduced and used in dm_hash_remove_all(). Otherwise, "rmmod -f"
may be stuck and never return.
And now, because the mapped_device is deleted at this point, subsequent
accesses to the mapped_device may cause NULL pointer references.
Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes dm_hash_remove_all() to release _hash_lock when
removing a device. After removing the device, dm_hash_remove_all()
takes _hash_lock and searches the hash from scratch again.
This patch is a preparation for the next patch, which changes device
deletion code to wait for md reference to be 0. Without this patch,
the wait in the next patch may cause AB-BA deadlock:
CPU0 CPU1
-----------------------------------------------------------------------
dm_hash_remove_all()
down_write(_hash_lock)
table_status()
md = find_device()
dm_get(md)
<increment md->holders>
dm_get_live_or_inactive_table()
dm_get_inactive_table()
down_write(_hash_lock)
<in the md deletion code>
<wait for md->holders to be 0>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch prevents access to mapped_device which is being deleted.
Currently, even after a mapped_device has been removed from the hash,
it could be accessed through idr_find() using minor number.
That could cause a race and NULL pointer reference below:
CPU0 CPU1
------------------------------------------------------------------
dev_remove(param)
down_write(_hash_lock)
dm_lock_for_deletion(md)
spin_lock(_minor_lock)
set_bit(DMF_DELETING)
spin_unlock(_minor_lock)
__hash_remove(hc)
up_write(_hash_lock)
dev_status(param)
md = find_device(param)
down_read(_hash_lock)
__find_device_hash_cell(param)
dm_get_md(param->dev)
md = dm_find_md(dev)
spin_lock(_minor_lock)
md = idr_find(MINOR(dev))
spin_unlock(_minor_lock)
dm_put(md)
free_dev(md)
dm_get(md)
up_read(_hash_lock)
__dev_status(md, param)
dm_put(md)
This patch fixes such problems.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All the dm ioctls that generate uevents set the DM_UEVENT_GENERATED flag so
that userspace knows whether or not to wait for a uevent to be processed
before continuing,
The dm rename ioctl sets this flag but was not structured to return it
to userspace. This patch restructures the rename ioctl processing to
behave like the other ioctls that return data and so fix this.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove useless __dev_status call while processing an ioctl that sets up
device geometry and target message. The data is not returned to
userspace so there is no point collecting it and in the case of
target_message it is collected before processing the message so if it
did return it might be stale.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Validate chunk size against both origin and snapshot sector size
Don't allow chunk size smaller than either origin or snapshot logical
sector size. Reading or writing data not aligned to sector size is not
allowed and causes immediate errors.
This requires us to open the origin before initialising the
exception store and to export dm_snap_origin.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Iterate both origin and snapshot devices
iterate_devices method should call the callback for all the devices where
the bio may be remapped. Thus, snapshot_iterate_devices should call the callback
for both snapshot and origin underlying devices because it remaps some bios
to the snapshot and some to the origin.
snapshot_iterate_devices called the callback only for the origin device.
This led to badly calculated device limits if snapshot and origin were placed
on different types of disks.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
multipath_ctr() forgets to return an error after detecting
missing path parameters. Fix this.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'for-linus' of git://neil.brown.name/md: (24 commits)
md: clean up do_md_stop
md: fix another deadlock with removing sysfs attributes.
md: move revalidate_disk() back outside open_mutex
md/raid10: fix deadlock with unaligned read during resync
md/bitmap: separate out loading a bitmap from initialising the structures.
md/bitmap: prepare for storing write-intent-bitmap via dm-dirty-log.
md/bitmap: optimise scanning of empty bitmaps.
md/bitmap: clean up plugging calls.
md/bitmap: reduce dependence on sysfs.
md/bitmap: white space clean up and similar.
md/raid5: export raid5 unplugging interface.
md/plug: optionally use plugger to unplug an array during resync/recovery.
md/raid5: add simple plugging infrastructure.
md/raid5: export is_congested test
raid5: Don't set read-ahead when there is no queue
md: add support for raising dm events.
md: export various start/stop interfaces
md: split out md_rdev_init
md: be more careful setting MD_CHANGE_CLEAN
md/raid5: ensure we create a unique name for kmem_cache when mddev has no gendisk
...
There is only one error exit from do_md_stop, so make that more
explicit and discard the 'err' variable.
Also drop the 'revalidate' variable by moving the unlock calls around.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the deletion of sysfs attributes from reconfig_mutex to
open_mutex didn't really help as a process can try to take
open_mutex while holding reconfig_mutex, so the same deadlock can
happen, just requiring one more process to be involved in the chain.
I looks like I cannot easily use locking to wait for the sysfs
deletion to complete, so don't.
The only things that we cannot do while the deletions are still
pending is other things which can change the sysfs namespace: run,
takeover, stop. Each of these can fail with -EBUSY.
So set a flag while doing a sysfs deletion, and fail run, takeover,
stop if that flag is set.
This is suitable for 2.6.35.x
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa5 "md: remove ->changed and related code" moved
revalidate_disk() under open_mutex, and lockdep noticed.
[ INFO: possible circular locking dependency detected ]
2.6.32-mdadm-locking #1
-------------------------------------------------------
mdadm/3640 is trying to acquire lock:
(&bdev->bd_mutex){+.+.+.}, at: [<ffffffff811acecb>] revalidate_disk+0x5b/0x90
but task is already holding lock:
(&mddev->open_mutex){+.+...}, at: [<ffffffffa055e07a>] do_md_stop+0x4a/0x4d0 [md_mod]
which lock already depends on the new lock.
It is suitable for 2.6.35.x
Cc: <stable@kernel.org>
Reported-by: Przemyslaw Czarnowski <przemyslaw.hawrylewicz.czarnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If the 'bio_split' path in raid10-read is used while
resync/recovery is happening it is possible to deadlock.
Fix this be elevating ->nr_waiting for the duration of both
parts of the split request.
This fixes a bug that has been present since 2.6.22
but has only started manifesting recently for unknown reasons.
It is suitable for and -stable since then.
Reported-by: Justin Bronder <jsbronder@gentoo.org>
Tested-by: Justin Bronder <jsbronder@gentoo.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
dm makes this distinction between ->ctr and ->resume, so we need to
too.
Also get the new bitmap_load to clear out the bitmap first, as this is
most consistent with the dm suspend/resume approach
Signed-off-by: NeilBrown <neilb@suse.de>
This allows md/raid5 to fully work as a dm target.
Normally md uses a 'filemap' which contains a list of pages of bits
each of which may be written separately.
dm-log uses and all-or-nothing approach to writing the log, so
when using a dm-log, ->filemap is NULL and the flags normally stored
in filemap_attr are stored in ->logattrs instead.
Signed-off-by: NeilBrown <neilb@suse.de>
A bitmap is stored as one page per 2048 bits.
If none of the bits are set, the page is not allocated.
When bitmap_get_counter finds that a page isn't allocate,
it just reports that one bit work of space isn't flagged,
rather than reporting that 2048 bits worth of space are
unflagged.
This can cause searches for flagged bits (e.g. bitmap_close_sync)
to do more work than is really necessary.
So change bitmap_get_counter (when creating) to report a number of
blocks that more accurately reports the range of the device for which
no counter currently exists.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ use md_unplug in bitmap.c as we will soon be using bitmaps under
arrays with no queue attached.
2/ Don't bother plugging the queue when we set a bit in the bitmap.
The reason for this was to encourage as many bits as possible to
get set before we unplug and write stuff out.
However every personality already plugs the queue after
bitmap_startwrite either directly (raid1/raid10) or be setting
STRIPE_BIT_DELAY which causes the queue to be plugged later
(raid5).
Signed-off-by: NeilBrown <neilb@suse.de>
For dm-raid45 we will want to use bitmaps in dm-targets which don't
have entries in sysfs, so cope with the mddev not living in sysfs.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes some whitespace problems
Fixed some checkpatch.pl complaints.
Replaced kmalloc ... memset(0), with kzalloc
Fixed an unlikely memory leak on an error path.
Reformatted a number of 'if/else' sets, sometimes
replacing goto with an else clause.
Removed some old comments and commented-out code.
Signed-off-by: NeilBrown <neilb@suse.de>
If an array doesn't have a 'queue' then md_do_sync cannot
unplug it.
In that case it will have a 'plugger', so make that available
to the mddev, and use it to unplug the array if needed.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5 uses the plugging infrastructure provided by the block layer
and 'struct request_queue'. However when we plug raid5 under dm there
is no request queue so we cannot use that.
So create a similar infrastructure that is much lighter weight and use
it for raid5.
Signed-off-by: NeilBrown <neilb@suse.de>
the dm module will need this for dm-raid45.
Also only access ->queue->backing_dev_info->congested_fn
if ->queue actually exists. It won't in a dm target.
Signed-off-by: NeilBrown <neilb@suse.de>
dm-raid456 does not provide a 'queue' for raid5 to use,
so we must make raid5 stop depending on the queue.
First: read_ahead
dm handles read-ahead adjustment fully in userspace, so
simply don't do any readahead adjustments if there is
no queue.
Also re-arrange code slightly so all the accesses to ->queue are
together.
Finally, move the blk_queue_merge_bvec function into the 'if' as
the ->split_io setting in dm-raid456 has the same effect.
Signed-off-by: NeilBrown <neilb@suse.de>
dm uses scheduled work to raise events to user-space.
So allow md device to have work_structs and schedule them on an error.
Signed-off-by: NeilBrown <neilb@suse.de>
export entry points for starting and stopping md arrays.
This will be used by a module to make md/raid5 work under
dm.
Also stop calling md_stop_writes from md_stop, as that won't
work well with dm - it will want to call the two separately.
Signed-off-by: NeilBrown <neilb@suse.de>
This functionality will be needed separately in a subsequent patch, so
split it into it's own exported function.
Signed-off-by: NeilBrown <neilb@suse.de>
When MD_CHANGE_CLEAN is set we might block in md_write_start.
So we should only set it when fairly sure that something will clear
it.
There are two places where it is set so as to encourage a metadata
update to record the progress of resync/recovery. This should only
be done if the internal metadata update mechanisms are in use, which
can be tested by by inspecting '->persistent'.
Signed-off-by: NeilBrown <neilb@suse.de>
We will shortly allow md devices with no gendisk (they are attached to
a dm-target instead). That will cause mdname() to return 'mdX'.
There is one place where mdname really needs to be unique: when
creating the name for a slab cache.
So in that case, if there is no gendisk, you the address of the mddev
formatted in HEX to provide a unique name.
Signed-off-by: NeilBrown <neilb@suse.de>
We will want md devices to live as dm targets where sysfs is not
visible. So allow md to not connect to sysfs.
Signed-off-by: NeilBrown <neilb@suse.de>
There are few situations where it would make any sense to add a spare
when reducing the number of devices in an array, but it is
conceivable: A 6 drive RAID6 with two missing devices could be
reshaped to a 5 drive RAID6, and a spare could become available
just in time for the reshape, but not early enough to have been
recovered first. 'freezing' recovery can make this easy to
do without any races.
However doing such a thing is a bad idea. md will not record the
partially-recovered state of the 'spare' and when the reshape
finished it will think that the spare is still spare.
Easiest way to avoid this confusion is to simply disallow it.
Signed-off-by: NeilBrown <neilb@suse.de>
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
Signed-off-by: NeilBrown <neilb@suse.de>
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
Signed-off-by: NeilBrown <neilb@suse.de>
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
Signed-off-by: NeilBrown <neilb@suse.de>
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover(). That
gets set in run()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa572 broke partition
detection for md arrays.
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
By the previous modification, the cpu notifier can return encapsulate
errno value. This converts the cpu notifiers for raid5.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
get rid of home-grown mutex in cris eeprom.c
switch ecryptfs_write() to struct inode *, kill on-stack fake files
switch ecryptfs_get_locked_page() to struct inode *
simplify access to ecryptfs inodes in ->readpage() and friends
AFS: Don't put struct file on the stack
Ban ecryptfs over ecryptfs
logfs: replace inode uid,gid,mode initialization with helper function
ufs: replace inode uid,gid,mode initialization with helper function
udf: replace inode uid,gid,mode init with helper
ubifs: replace inode uid,gid,mode initialization with helper function
sysv: replace inode uid,gid,mode initialization with helper function
reiserfs: replace inode uid,gid,mode initialization with helper function
ramfs: replace inode uid,gid,mode initialization with helper function
omfs: replace inode uid,gid,mode initialization with helper function
bfs: replace inode uid,gid,mode initialization with helper function
ocfs2: replace inode uid,gid,mode initialization with helper function
nilfs2: replace inode uid,gid,mode initialization with helper function
minix: replace inode uid,gid,mode init with helper
ext4: replace inode uid,gid,mode init with helper
...
Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
Conflicts:
drivers/md/md.c
- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the last user passing a NULL file pointer is gone we can remove
the redundant dentry argument and associated hacks inside vfs_fsynmc_range.
The next step will be removig the dentry argument from ->fsync, but given
the luck with the last round of method prototype changes I'd rather
defer this until after the main merge window.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Devices which know that they are spares do not really need to have
an event count that matches the rest of the array, so there are no
data-in-sync issues. It is enough that the uuid matches.
So remove the requirement that the event count is up-to-date.
We currently still write out and event count on spares, but this
allows us in a year or 3 to stop doing that completely.
Signed-off-by: NeilBrown <neilb@suse.de>
When updating the event count for a simple clean <-> dirty transition,
we try to avoid updating the spares so they can safely spin-down.
As the event_counts across an array must be +/- 1, this means
decrementing the event_count on a dirty->clean transition.
This is not always safe and we have to avoid the unsafe time.
We current do this with a misguided idea about it being safe or
not depending on whether the event_count is odd or even. This
approach only works reliably in a few common instances, but easily
falls down.
So instead, simply keep internal state concerning whether it is safe
or not, and always assume it is not safe when an array is first
assembled.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync. This has a
very small chance of returning wrong data.
Reported-by: Jordan Russell <jr-list-2010@quo.to>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Many 'printk' messages from the raid456 module mention 'raid5' even
though it may be a 'raid6' or even 'raid4' array. This can cause
confusion.
Also the actual array name is not always reported and when it is
it is not reported consistently.
So change all the messages to start:
md/raid:%s:
where '%s' becomes e.g. md3 to identify the particular array.
Signed-off-by: NeilBrown <neilb@suse.de>
RAID10 has been available for quite a while now and is quite well
tested, so we can remove the EXPERIMENTAL designation.
Reported-by: Eric MSP Veith <eveith@wwweb-library.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Level modifications change the output of mdstat. The mdmon manager
thread is interested in these events for external metadata management.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a raid1 array is configured to support write-behind
on some devices, it normally only reads from other devices.
If all devices are write-behind (because the rest have failed)
it is possible for a read request to be serviced before a
behind-write request, which would appear as data corruption.
So when forced to read from a WriteMostly device, wait for any
write-behind to complete, and don't start any more behind-writes.
Signed-off-by: NeilBrown <neilb@suse.de>
This message seems to suggest the named device is the one on which a
read failed, however it is actually the device that the read will be
redirected to.
So make the message a little clearer.
Reported-by: Tim Burgess <ozburgess@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This is
- unnecessary because mddev_suspend is always followed by a call to
->stop, and each ->stop unregisters the thread, and
- a problem as it makes it awkwards to suspend and then resume a
device as we will want later.
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown
Adrian Drzewiecki
Mike Snitzer
Mikulas Patocka
Alasdair G Kergon
Milan Broz
Peter Rajnoha
Will Drewry
Tomohiro Kusumi
Julia Lawall
Arnd Bergmann
Kiyoshi Ueda
Linus Torvalds
David Woodhouse
Dan Williams
Arnd Bergmann
FUJITA Tomonori
Christoph Hellwig
Maciej Trela
Prasanna S. Panchamukhi
Akinobu Mita
Eric W. Biederman
Gabriele A. Trombetti