Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alok N Kataria <akataria@vmware.com>
Cc: "Tan Wei Chong" <wei.chong.tan@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Bob Moore <robert.moore@intel.com>
LKML-Reference: <1253137123-18047-2-git-send-email-felipe.contreras@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix the following 'make includecheck' warning:
drivers/xen/evtchn.c: linux/errno.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: chrisw@sous-sol.org
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247067749.4382.90.camel@ht.satnam>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
fix the following 'make includecheck' warning:
drivers/video/console/vgacon.c: linux/slab.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Martin Mares <mj@ucw.cz>
Cc: mchehab@infradead.org
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247067624.4382.88.camel@ht.satnam>
fix the following 'make includecheck' warning:
drivers/scsi/ibmvscsi/ibmvscsi.c: asm/firmware.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247067016.4382.78.camel@ht.satnam>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
fix the following 'make includecheck' warning:
drivers/scsi/fcoe/libfcoe.c: linux/netdevice.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247066936.4382.76.camel@ht.satnam>
As I2C is used by PMICs also, make the busses available early via
subsys_initcall().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The mv64xxx_i2c_intr() irq handler in drivers/i2c/busses/i2c-mv64xxx.c
is declared as returning 'int', resulting in this compile-time warning:
drivers/i2c/busses/i2c-mv64xxx.c: In function 'mv64xxx_i2c_probe':
drivers/i2c/busses/i2c-mv64xxx.c:540: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Fix: correct the return type to 'irqreturn_t'.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch (as1292) modifies the USB serial console driver, to make it
compatible with the recent changes to the USB serial core. The most
important change is that serial->disc_mutex now has to be unlocked
following a successful call to usb_serial_get_by_index().
Other less notable changes include:
Use the requested port number instead of port 0 always.
Prevent the serial device from being autosuspended.
Use the ASYNCB_INITIALIZED flag bit to indicate when the
port hardware has been initialized.
In spite of these changes, there's no question that the USB serial
console code is still a big hack.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1291) removes a bunch of code from serial_open(), things
that were rendered unnecessary by earlier patches. A missing spinlock
is added to protect port->port.count, which needs to be incremented
even if the open fails but not if the tty has gotten a hangup. The
test for whether the hardware has been initialized, based on the use
count, is replaced by a more transparent test of the
ASYNCB_INITIALIZED bit in the port flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1290) adds some missing tests. serial_down() isn't
supposed to do anything if the hardware hasn't been initialized, and
serial_close() isn't supposed to do anything if the tty has gotten a
hangup (because serial_hangup() takes care of shutting down the
hardware).
The patch also updates and adds a few debugging lines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1289) renames serial_do_down() to serial_down() and
serial_do_free() to serial_release(). It also adds a missing call to
tty_shutdown() in serial_release().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1288) fixes the initialization logic in
serial_install(). A new tty always needs to have a termios
initialized no matter what, not just in the case where the lower
driver will override the termios settings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1287) makes serial_install() be reponsible for acquiring
references to the usb_serial structure and the driver module when a
tty is first used. This is more sensible than having serial_open() do
it, because a tty can be opened many times whereas it is installed
only once, when it is created. (Not to mention that these actions are
reversed when the tty is released, not when it is closed.) Finally,
it is at install time that the TTY core takes its own reference to the
usb_serial module, so it is only fitting that we should act the same
way in regard to the lower-level serial driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1286) changes usb_serial_get_by_index(). Now the
routine will check whether the serial device has been disconnected; if
it has then the return value will be NULL. If the device hasn't been
disconnected then the routine will return with serial->disc_mutex
held, so that the caller can use the structure without fear of racing
against driver unloads.
This permits the scope of table_mutex in destroy_serial() to be
reduced. Instead of protecting the entire function, it suffices to
protect the part that actually uses serial_table[], i.e., the call to
return_serial(). There's no longer any danger of the refcount being
incremented after it reaches 0 (which was the reason for having the
large scope previously), because it can't reach 0 until the serial
device has been disconnected.
Also, the patch makes serial_install() check that serial is non-NULL
before attempting to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1285) rearranges the subroutines in usb-serial.c
concerned with tty lifetimes into a more logical order: install, open,
hangup, close, release. It also updates the formatting of the
kerneldoc comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1284) changes the referencing of the usb_serial and
usb_serial_port structures in usb-serial.c. It's not feasible to make
the port structures keep a reference to the serial structure, because
the ports need to remain in existence when serial is released -- quite
a few of the drivers expect this. Consequently taking a reference
to the port when the device file is open is insufficient; such a
reference would not pin serial.
To fix this, we now take a reference to serial when the device file is
opened. The final put_device() for the ports occurs in
destroy_serial(), so that the ports will last as long as they are
needed.
The patch initializes all the port devices, including those in the
unused "fake" ports. This makes the code more uniform because they
can all be released in the same way. The error handling code in
usb_serial_probe() is much simplified by this approach; instead of
freeing everything by hand we can use a single usb_serial_put() call.
Also simplified is the port-release mechanism. Instead of being two
separate routines, port_release() and port_free() can be combined into
one.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In moxa specific ASPP_OQUEUE ioctl command, they apparently want
only know whether there is space in transmitter hold register.
So switch UART_LSR_TEMT to UART_LSR_THRE in that specific case
according to the change in 1.14 moxa drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for MOXA:0x1120 pci device. It's a 2-port device and differs
in no way from the others. So this turns out to be a trivial
pci_device_id change.
Increase also the version number.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a tty refcnt leak in read_int_callback. In fact
it's handled wrong altogether. tty_port_tty_get can return NULL
and it's not checked in that manner.
Fix that by checking the tty_port_tty_get retval and put tty kref
properly.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a tty refcnt leak on one fail path in rc_transmit.
Fix that by jumping to the 'out' label.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty_port_ops.shutdown takes only one parameter: tty port. Remove
the second one and use port->tty where needed instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1282) fixes some obvious typos in the TTY core.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vt_waitactive no longer accepts console parameter as console-1
since commit "vt: add an event interface". It expects console
number directly (as viewed by userspace -- counting from 1).
Fix a deadlock suspend regression by redefining adding one
to vt in vt_move_to_console.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VT specific compat_ioctl handlers are the only ones
in common code that require the BKL. Moving them into
the vt driver lets us remove the BKL from the other handlers
and cleans up the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check L_ECHOCTL before insertting a character in the echo buffer
(rather than as the buffer is processed), to be more consistent with
when all other L_ flags are checked. Also cleaned up the related logic.
Note that this and the previous patch ("n_tty: honor opost flag for echoes")
were verified together by the reporters of the bug that patch addresses
(http://bugs.linuxbase.org/show_bug.cgi?id=2692), and the test now passes.
Signed-off-by: Joe Peterson <joe@skyrush.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes the following bug:
http://bugs.linuxbase.org/show_bug.cgi?id=2692
Causes processing of echoed characters (output from the echo buffer) to
honor the O_OPOST flag, which is consistent with the old behavior.
Note that this and the next patch ("n_tty: move echoctl check and
clean up logic") were verified together by the bug reporters, and
the test now passes.
Signed-off-by: Joe Peterson <joe@skyrush.com>
Cc: Linux Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b5b82df6, from May 2007, breaks no_console_suspend on the OLPC
XO laptop. Basically what happens is that upon returning from resume,
serial8250_resume_port() will reconfigure the port for high speed
mode and all console output will be garbled, making debug of the
resume path painful. This patch modifies uart_resume_port() to
reset the port to the state it was in before we suspended.
Original patch by Marcelo Tosatti
Second patch by Deepak then reworked by Alan to fit with the tty changes
before it got submitted. Also fixed the console path to set c_i/ospeed as
some drivers require the termios fields are valid
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial layer for some reason uses different defines for the special
case close delays and then conditionally switches to/from the normal ones
in the ioctls.
Remove this rather pointless abstraction
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This little helper is now tty_port specific and useful generally so move it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They cover essentially the same stuff and we can therefore fold it into the
tty_port one.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fortunately the serial layer was designed to use the same flag values but
with different names. It has its own SUSPENDED flag which is a free slot in
the ASYNC flags so we allocate it in the ASYNC flags instead.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extract out a lot of the x.port. uses and also show up where there are
things left to be isolated that prevent use using the port helpers in the
serial layer at this point
Signed-off-by: Alan Cox <alan@linux.intel.com>
We moved this into uart_state, now move the fields out of the separate
structure and kill it off.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
X and other graphical interfaces need to be able to flip to a console
and lock it into graphics mode without races.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the past someone gratuitiously borrowed chunks of kernel internal vt
code and dumped them in kernel/power. They have all sorts of deep relations
with the vt code so put them in the vt tree instead
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed and requested in various forms for ConsoleKit, screenblank
handling and the like so do the job with a single interface. Also build the
interface so that unlike VT_WAITACTIVE and friends it won't miss events.
FIXME: Should this be a waitactive ioctl or a new device file you can poll
and read events from. We need the code anyway to fix up the existing broken
wait for console switch logic but the ConsoleKit people would prefer the
new device to the ioctl we have here
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are handled by the tty_port core code which will raise and lower the
carrier correctly in tty_wait_until_ready
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB layer uses tty_hangup to deal with unplugs of the physical hardware
(analogous to loss of carrier) and then frees the resources. However the
tty_hangup is asynchronous. As the hangup can sleep we can use tty_vhangup
which is the non async version to avoid freeing resources too early.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changed in 2006 so its about time the ACM driver caught up
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to be able to sleep in the destructor for USB at least. It isn't a
hot path so just pushing it to a work queue doesn't really cause any
difficulty.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert cyclades to use the full tty_port_close helper
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to kref this driver in order to use port_close
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now we are extracting out methods for shutdown and the like we can add a
proper tty_port_close method that knows all the innards of the tty closing
process and hides the lot from the caller.
At some point in the future this will be paired with a similar open()
helper and the drivers can stick to hardware management.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A platform clock drives 8250 ports in most SOC systems, the clock
might run at high frequencies, and so it's not always possible to
downscale uart clock to a desired value.
Currently the 8250 uart driver accepts not supported baud rates, and
what is worse, it is doing this silently, and then passes not accepted
values to a new termios, so userspace has no chance to catch this kind
of errors (userspace verifies that settings were accepted by reading
back and comparing the settings).
This patch fixes the issue by passing minimum baud rate to the
uart_get_baud_rate() call, the call should take care of all bounds,
so userspace should now report:
# stty -F /dev/ttyS0 speed 300
115200
stty: /dev/ttyS0: unable to perform all requested operations
p.s. uart_get_baud_rate() falls back to 9600, which still might be too
low for some 10 GHz platforms, but that's a separate issue, and
we can wait with fixing this till we find such a platform.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is currently no provision for passing IRQ trigger flags for
serial IRQs with triggering requirements (such as GPIO IRQs)
This patch adds irqflags to plat_serial8250_port that can be passed
from board file to reqest_irq() of 8250 driver
Changes are backward compatible with boards passing UPF_SHARE_IRQ flag
Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq
[Moved new flag to end to fix bugs in the original with the old_serial array
-- Alan]
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem ioctls are not routed via the ioctl method so kill the old dead
code. The correct code is also already present and hooked in.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I made a correction for get_lsr_info, now it returns some meaningful
information. I tested it with two simultaneous simplex modem channels.
it is attached
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the tiocmget/mset handling on the mos7720 USB serial port.
[Minor space reformatting for coding style - Alan]
Signed-off-by: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The network layer now has a destructor we can hook to clean up the slip
devices array. That needs us to initiate unregister events in the right
places which with the current tty layer we can do, and with network
refcounting is safe to do.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicated code from cy_set_line_char. There were 2 if
branches with same contents except flags.
Branch only for the flags computation and use them in the only copy
of the code.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add helpers for io operations, so that we can eliminate huge
amount of supporting code. It is now centralized in those
helpers and used values are precomputed in the init phase.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- save one indent level by inverting !fw_loaded condition
- read rs_status on Z and write it after we change all the flags,
don't do that separately
- remove Y inverted rts/dtr branching, precompute registers and use
them
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add a cy_ prefix to functions with changed prototypes
- cy_get_serial_info: initialize serial_struct by initializer,
save a memset
- inline simple functions (get_mon_info, {s,g}et_default_threshold,
{s,g}et_default_timeout) directly in the ioctl handler
- add a cy_cflags_changed helper to not copy its code by
wait_event_interruptible
- remove some ret_val = 0 assignments, it's preset to 0
- TIOCGICOUNT: don't do many put_user's, do one copy_to_user
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a duplicated code for Y and Z in cy_startup, merge the paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For Z cards, use tty helpers for dtr_rts.
If we did the same for Y cards, it will cause a deadlock, because
cyy_dtr_rts takes a lock which we already hold.
Instead, we introduce a Y helper expecting card lock to be held.
It may then be called with set/clear masks from other places.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid long busy loops (5 ms) which may be replaced by sleeps.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- remove changelog from the file. we don't care about ancient
history
- update copyright year
- update version
- constify some stuff
- empty lines removal
- unused variables and macros removal
- remove some asm/ includes, they are sucked by linux/ variants
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use new tty helpers for close, which allows much code removal.
The only real change is locking. card_lock for protecting was
used inappropriately (just to have a critical section, no matter
which lock is used), so the change to port->lock is fine.
Remove also useless debug printks while being there.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not duplicate common tty_port_hangup code. Use it instead.
Also do not unset ASYNC_NORMAL_ACTIVE and wake up from the
tty_hangup() caller. It makes no sense since we don't check that
flag in sleepers. tty_port_hangup() performed later will do the
right job.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't fetch firmware address and recompute channel control on each
port access. Precompute the values on init and use them later all
the time.
The same for board control.
This simplify code and improves readability.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use a tty_port common instead. This saves lots of .text and makes the
code a lot more readable.
This involves separation of a dtr_rts handling, next patches will use
that to not duplicate the code all over the place.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While this is not problem for Y card handlers (they are protected
by card_lock), Z handlers and other functions may dereference NULL
at any point after hangup/close. Even if (tty == NULL) was already
performed in the handler.
Note that it's not an issue for Y cards just for now. After
switching to tty_port_close_* et al. this will be a problem. So
add refcounting to them all.
Also proc .show doesn't take a tty reference and it should (along
with a ldisc one).
While at it and changing prototypes (adding tty param), prepend
cy_ to functions which don't have it yet.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously, if any bit other than CMD_SND_BREAK was set, CMD_SND_BREAK
was not unset.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the following 'make includecheck' warning:
drivers/char/vt.c: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the /proc/tty/ldiscs handling doesn't play games with 'struct
ldisc' any more, the only remaining user of 'tty_ldisc_try_get()' is
'tty_ldisc_get()' (note the lack of 'try').
And we're actually much better off folding the logic directly into that
file, since the 'try' part was always about trying to get the ldisc
operations, not the ldisc itself: and making that explicit inside of
'tty_ldisc_get()' clarifies the whole semantics.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>,
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /proc/tty/ldiscs file is totally and utterly un-interested in the
"struct tty_ldisc" structures, and only cares about the underlying ldisc
operations.
So don't make it create a dummy 'struct ldisc' only to get a pointer to
the operations, and then destroy it. Instead, we split up the function
'tty_ldisc_try_get()', and create a 'get_ldops()' helper that just looks
up the ldisc operations based on the ldisc number.
That makes the code simpler to read (smaller and more well-defined
helper functions), and allows the /proc functions to avoid creating that
useless dummy only to immediately free it again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module. Otherwise we get build failures due to the ifdef
handling.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty_operation chars_in_buffer() is not allowed to return a negative
value to signal an error. Corrects the problem flagged by commit
23198fda71, "tty: fix chars_in_buffers".
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "end of a C state" trace point currently happens before
the code runs that corrects the TSC for having stopped during idle.
The result of this is that the timestamp of the end-of-C-state event
is garbage on cpus where the TSC stops during idle.
This patch moves the end point of the C state to after the timekeeping
engine of the kernel has been corrected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090919133533.139c2a46@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
drivers/media/dvb/pt1/pt1.c: In function ‘pt1_probe’:
drivers/media/dvb/pt1/pt1.c:915: warning: ‘DMA_nnBIT_MASK’ is deprecated
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_info and v4l2_err where appropriate.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The brightness and contrast controls were added to the Sensoray 2250 device.
A read register function was added to set the correct bit fields.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some error cases, allocated buffers need to be freed before returning.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implemented the vidio_g_std and vidio_querystd ioctls.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The declarations for struct go7007_file *gofh and struct go7007 *go can
be merged when gofh isn't used by the function.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MPEG controls were disabled by Mauro's ioctl conversion patch. They are now
re-enabled and cleaned up.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace "weird device" with accurate descriptions. Add menu options and
makefile lines for the i2c modules. Added comment about why dvb-usb is
included. Added include sound/config.h for Ubuntu 8.04 distro kernel.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver for Analog Devices ADV7180 Video Decoder.
So far it only supports query standard.
[akpm@linux-foundation.org: remove unneeded cast]
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the kzalloc and associated test after the stream/query test, to avoid
the need to free the allocated if the stream/query test fails.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to rounding and clipping, exposure and gain settings do not map to
unique register values. Rather than read the registers and report gain
and exposure that may be different than the values that were set, just
cache the latest values that were set and report them. Reduce exposure
range from 0-65535 to 0-255 so libv4l's autogain doesn't take forever.
Remove vestiges of driver signal processing that is now handled by
libv4l.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize image size before it's used to initialize exposure.
Work around lack of exposure set hardware latch with a sequence of
register writes in a single I2C command packet.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
http://linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
test status analog (PAL-B):
- Sometimes picture is noisy, but it becomes crystal clear after
switching between channels. (happens for example at 687.25 Mhz)
- On a lower frequency (511.25 Mhz) the picture is always sharp, but
lacks colour.
- No sound problems.
- radio untested.
Digital:
- DVB-T/H stream reception works.
- Would expect to see some more channels in the higher frequency region.
Overall is the impression that sensitivity still needs improvement
both in analog and digital modes.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When fast push-pull button of remote control we can received incorrect
key code 0x00. Key information from IR decoder has ID of remote control 2 bytes,
byte of key code and byte of mirror key code.
Correct data
0x86 0x6B 0x00 0xFF
Wrong data
0x86 0x6B 0x00 0x00
This patch added additional test of mirror byte for filtering.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for 774 Friio White, ISDB-T USB receiver
Friio White is an USB 2.0 ISDB-T receiver. (http://www.friio.com/)
The device has a GL861 chip and a Comtech JDVBT90502 canned tuner module.
This driver ignores all the frontend_parameters except frequency,
as ISDB-T shares the same parameter configuration across the country
and thus the device can work like an intelligent one.
As this device does not include a CAM nor hardware descrambling feature,
the driver passes through scrambled TS streams.
There is Friio Black, a variant for ISDB-S, which shares the same USB
Vendor/Product ID with White, but it is not supported in this driver.
They should be identified in the initialization sequence,
but this feature is not tested.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for Earthsoft PT1
Eearthsoft PT1 is a PCI card for Japanese broadcasting with two ISDB-S
and ISDB-T demodulators.
This card has neither MPEG decoder nor conditional access module
onboard. It transmits only compressed and possibly encrypted MPEG data
over the PCI bus, so you need an external software decoder and a
decrypter to watch TV on your computer.
This driver is originally developed by Tomoaki Ishikawa
<tomy@users.sourceforge.jp> by reverse engineering.
[mchehab@redhat.com: renamed isdb_ts to isdbs_ts to use the current standard]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In ISDB-S, time-devision duplex is used to multiplexing several waves
in the same frequency. Each wave is identified by its own transport
stream ID, or TS ID. We need to provide some way to specify this ID
from user applications to handle ISDB-S frontends.
This code has been tested with the Earthsoft PT1 driver.
[mchehab@infradead.org: Fix merge conflicts with isdbt and rename the new parameter to DTV_ISDBS_TS_ID]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/gspca/gl860/gl860.c: In function ‘gl860_build_control_table’:
drivers/media/video/gspca/gl860/gl860.c:119: warning: ‘sd_ctrls’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/saa7164/saa7164-buffer.c: In function ‘saa7164_buffer_alloc’:
drivers/media/video/saa7164/saa7164-buffer.c:110: warning: cast to pointer from integer of different size
drivers/media/video/saa7164/saa7164-buffer.c:112: warning: cast to pointer from integer of different size
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Following changes done for vpif driver to support vpif capture:-
1) Current version of display driver defined vpif register
space as part for vpif display platform driver resource
This is not correct since vpif is common across capture
and display drivers. So the resource iomap function is
moved to this module
2) Since there are common registers, a spinlock is added for
mutual exclusion.
This has incorporated comments against version v0 of the patch series
Resending to merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the vpif capture bridge driver for DM6467. This video
supports two video channels each having a tvp5147 device at
the input. This allows simultaneous capture of NTSC/PAL video
in each of this channel. Both MMAP and USERPTR io mechanism
are supported. Currently buffer allocation happens at REQBUF
ioctl request. Since USERPTR IO is supported, this is not an
issue since user applications can allocate buffers and pass
the user space address to the driver. Following are TODOs :-
1) Adding support for allocation of buffers at init
2) VBI/HBI data service
This has incorporated comments received against version v0
of the patch series.
Resending to merge V4l linux-next
create mode 100644 drivers/media/video/davinci/vpif_capture.c
create mode 100644 drivers/media/video/davinci/vpif_capture.h
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure name for vpif display driver changed since it was not unique. So this
update is done to reflect the same. Also removed the code related to register
address space iomap. Uses v4l2_i2c_new_subdev_board() instead of
v4l2_i2c_new_probed_subdev() so that platform data can be added for subdevice
configuration for polarities.
This has incorporated comments against version v0 of the patch series.
Resending the original patch for merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some subtle differences in the way the devnode numbers are
handled depending on whether the FIXED_MINOR_RANGES config option is
set. Add some simple wrapper functions to handle that correctly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The term 'kernel number' is very vague, so replace it with the somewhat more
descriptive term 'device node number'.
In one place the local variable 'nr' was used to create the device node number
of the new device name. This has been replaced with the vdev->num field to
more clearly mark this as being the device node number and not the minor
number.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_register_device_index is never actually called, instead the
stream index number is always calculated automatically.
This patch removes this function and simplifies the internal get_index
function since that can now always just return the first free index.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we are not using v4l2_device_call_* calls any more, we don't need to
initialise subdevice .grp_id any more. This also fixes compiler warnings on
64-bit platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the soc-camera interface for V4L2 subdevices thinner yet. Handle
gain and exposure internally in each driver just like all other controls.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unneeded soc-camera operations, this also makes the soc-camera API to
v4l2 subdevices thinner.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial soc-camera scaling and cropping implementation turned out to be
incompliant with the V4L2 API, e.g., it expected the user to specify cropping
in output window pixels, instead of input window pixels. This patch converts
the soc-camera core and all drivers to comply with the standard.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_subdev_call() instead of v4l2_device_call_until_err() in all host
drivers and in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove set_crop soc-camera device method and switch to s_crop from v4l2-subdev
video operations. Also extend non-i2c drivers to also hold a pointer to their
v4l2-subdev instance in control device driver-data, i.e., in
dev_get_drvdata((struct device *)to_soc_camera_control(icd))
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use host-side image scaling when the client fails to set the requested format.
We also have to take scaling into account when performing host-side cropping.
Similar to cropping we try to use client-side scaling as much as possible to
preserve bus bandwidth and optimise the frame-rate.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current tw9910 driver does not implement cropping correctly. Therefore, and
also because various rectangles in struct soc_camera_device are in user scale,
we cannot and shall not use rect_current as window location.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OV772x sensors cannot crop, they only support two fixed formats: VGA and QVGA.
We should not change the format when requested to crop, only S_FMT can do this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prohibit S_FMT and S_CROP with a different window width or height after video
buffer initialisation. This simplifies the work to be done in specific host and
client drivers, and it doesn't seem to make much sense to allow these changes.
We do however allow S_CROP with equal width and height to just move the window,
this doesn't affect video buffer management and is usually easy enough to
implement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API mandates, that drivers do not update the argument of the S_CROP
ioctl() with the actual geometry. Comply.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all video capture devices can configure arbitrary cropping, whereas the
CEU module on SuperH CPUs can crop with pixel precision. However, we want to
use camera cropping if possible to save bandwidth and increase the frame-rate.
This patch verifies whether the camera managed to crop exactly the requested
rectangle, and if not, uses host-side cropping. To be able to crop on CEU we
have to preserve camera rectangle too, for which the host_priv member in
struct soc_camera_device is used. We now allocate memory dynamically, thus we
have to use the .put_formats() method from struct soc_camera_host_ops to free
it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch
[PATCH] video: use videobuf_waiton() in sh_mobile_ceu free_buffer()
was not quite correct. It closed a race, but introduced a potential
lock-up, if for some reason an interrupt does not come. This has been
observed in tests with tw9910. This patch safely dequeues buffers without
waiting for their completion. It also moves a buffer state assignment
under a spinlock to make it atomic with queuing of the buffer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The move of format translation initialisation into soc_camera_open() was
temporary for the soc-camera as platform driver intermediate step, put it back
into soc_camera_probe(). Also add a .put_formats() method to
soc_camera_host_ops to free any resources host driver might have allocated in
.get_formats().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 drivers are allowed to configure a geometry different than what has been
requested by the user with S_CROP, but then they have to adjust the input
rectangle accordingly. Fix ov772x to comply with this requirement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. soc-camera always requests a valid rectangle, when calling .s_fmt(), no need
to check and adjust
2. in .s_crop(), if the rectangle exceeds sensor limits, push it to the
respective border instead of centering
3. take into account left and top borders when checking
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ingo Molnar
Felipe Contreras
Jaswinder Singh Rajput
Wolfram Sang
Mikael Pettersson
Alan Stern
Jiri Slaby
Peter Korsgaard
Marcin Slusarz
Arnd Bergmann
Joe Peterson
Alan Cox
Deepak Saxena
Anton Vorontsov
Vikram Pandita
Kees Schoenmakers
Roel Kluin
Jaswinder Singh Rajput
Linus Torvalds
Mike Frysinger
Tilman Schmidt
Kay Sievers
Arjan van de Ven
Mauro Carvalho Chehab
Huang Weiyi
Pete Eberlein
Richard Röjfors
Vladimir Geroy
Matti J. Aaltonen
Julia Lawall
Dmitry Belimov
James Blanford
Erik Andrén
Andreas Mohr
Henk Vergonet
Akihiro Tsukada
HIRANO Takahito
Muralidharan Karicheri
Hans Verkuil
Guennadi Liakhovetski