Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.
Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved. As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt. Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.
I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state. This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().
While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary. OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.
Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The RGMII spec allows compliance for devices that implement an internal
delay on TXC or RXC inside the transmitter. This patch adds an RGMII_ID
definition to support RGMII-ID devices in the phylib.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most PHYs connect to an ethernet controller over a GMII or MII
interface. However, a growing number are connected over
different interfaces, such as RGMII or SGMII.
The ethernet driver will tell the PHY what type of connection it
is by setting it manually, or passing it in through phy_connect
(or phy_attach).
Changes include:
* Updates to documentation
* Updates to PHY Lib consumers
* Changes to PHY Lib to add interface support
* Some minor changes to whitespace in phy.h
* gianfar driver now detects interface and passes appropriate
value to PHY Lib
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The <linux/phy.h> uses some types and macros defined in
<linux/ethtool.h>, <linux/mii.h>, <linux/timer.h> and <linux/workqueue.h>,
but fails to include these headers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-include-phy-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the PHY_ID_FMT macro to ensure that the format of the id string used by a
driver to match to its specific phy is consistent between the mdio_bus and the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds a phy_mask field to struct mii_bus and uses it. This field
indicates each phy address to be ignored when probing the mdio bus.
This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds back the code that was taken out, thus re-enabling:
* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer
This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Maciej W. Rozycki
Kim Phillips
Andy Fleming
Vitaly Bordug
Kumar Gala
Matt Porter
Jeff Garzik