The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.
This is not supported with Thunderbolt 1-3 devices, though.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.
Also add tb_ prefix to the enum while there.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically retimers can be accessed only when the USB4 link is up (e.g
there is a cable connected). However, sometimes it is useful to be able
to access retimers even if there is nothing connected to the USB4 port.
For instance we may still want to be able to upgrade the retimer NVM
firmware even if the user does not have any USB4 devices. This is
something that USB4 spec leaves to implementers.
In case of ACPI based systems, we can support this by providing a
special _DSM method under each USB4 port. This _DSM can be used to turn
on power to on-board retimers (and cycle it through different modes so
that the sideband becomes usable).
This patch adds support for this _DSM and makes the functionality
available to the rest of the driver through tb_acpi_power_[on|off]_retimers().
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB4 Connection Manager guide provides detailed information how the
USB4 router buffer (credit) allocation information should be used by the
connection manager when it allocates buffers for different paths. This
patch implements it for Linux. For USB 3.x and DisplayPort we use
directly the router preferences. The rest of the buffer space is then
used for PCIe and DMA (peer-to-peer, XDomain) traffic. DMA tunnels
require at least one buffer and PCIe six, so if there is not enough
buffers we fail the tunnel creation.
For the legacy Thunderbolt 1-3 devices we use the existing hard-coded
scheme except for DMA where we use the values suggested by the USB4 spec
chapter 13.
Co-developed-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Once lane bonding has been enabled (or disabled) both lane adapters may
update their total credits accordingly. For this reason re-read the port
credits after lane bonding has been enabled or disabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.
Read this information and store it as part of struct tb_switch for each
USB4 router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It may take some time until the two lanes enter bonded state so poll for
the link width to match what is expected before going forward. This ensures
the link is in expected state before we start establishing paths through
it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
With the USB4 buffer allocation the number of credits (and non-flow
credits) may be different depending on the router buffer allocation
preferences. To allow this move the nfc_credits field to struct
tb_path_hop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.
Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We do this for Thunderbolt 2/3 devices through DMA port, USB4 devices
and retimers pretty much the same way. Only the actual block read/write
is different. For this reason split out the NVM read/write functions
from usb4.c to nvm.c and make USB4 device code call these when needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we have had an artificial limitation of a single DMA tunnel
per XDomain connection. However, hardware wise there is no such limit
and software based connection manager can take advantage of all the DMA
rings available on the host to establish tunnels.
For this reason make the tb_xdomain_[enable|disable]_paths() to take the
DMA ring and HopID as parameter instead of storing them in the struct
tb_xdomain. We also add API functions to allocate input and output
HopIDs of the XDomain connection that the service drivers can use
instead of hard-coding.
Also convert the two existing service drivers over to this API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the firmware connection manager is not proxying between the
software and the hardware we can decrease the timeout for control
packets significantly. The USB4 spec recommends 10 ms +- 1 ms but we use
slightly larger value (100 ms) which is recommendation from Intel
Thunderbolt firmware folks. When firmware connection manager is running
then we keep using the existing 5000 ms.
To implement this we move the control channel allocation to
tb_domain_alloc(), and pass the timeout from that function to the
tb_ctl_alloc(). Then make both connection manager implementations pass
the timeout when they alloc the domain structure.
While there update kernel-doc of struct tb_ctl to match the reality.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop the two functions not used anymore in the driver.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
ACPI 6.4 introduced a new _OSC capability used to negotiate whether the
OS is supposed to use Software (native) or Firmware based Connection
Manager. If the native support is granted then there are set of bits
that enable/disable different tunnel types that the Software Connection
Manager is allowed to tunnel.
This adds support for this new USB4 _OSC accordingly. When PCIe
tunneling is disabled then the driver switches security level to be
"nopcie" following the security level 5 used in Firmware based
Connection Manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
This allows disabling XDomain protocol completely if the user does not
plan to use the USB4/Thunderbolt peer-to-peer functionality, or for
security reasons.
XDomain protocol is enabled by default but with this commit it is
possible to disable it by passing "xdomain=0" as module parameter (or
through the kernel command line).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
USB4 spec talks about routers and adapters whereas Thunderbolt 1-3
talked about CIO (Converged I/O) switches and ports. These are the same
thing but might cause confusion so add clarifying comments to struct
tb_switch and struct tb_port about the USB4 terms.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases it is useful to be able de-authorize devices. For example
if user logs out the userspace can have a policy that disconnects PCIe
devices until logged in again. This is only possible for software based
connection manager as it directly controls the tunnels.
For this reason make the authorized attribute accept writing 0 which
makes the software connection manager to tear down the corresponding
PCIe tunnel. Userspace can check if this is supported by reading a new
domain attribute deauthorization, that holds 1 in that case.
While there correct tb_domain_approve_switch() kernel-doc and
description of authorized attribute to mention that it is only about
PCIe tunnels.
Cc: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
USB4 spec says that for TBT3 compatible device routers the connection
manager needs to set SLI (Start Lane Initialization) to get the lanes
that were not connected back to functional state after sleep. Same needs
to be done if the link was XDomain.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
This includes following Thunderbolt/USB4 changes for v5.11 merge window:
* DMA traffic test driver
* USB4 router NVM upgrade improvements
* USB4 router operations proxy implementation available in the recent
Intel Connection Manager firmwares
* Support for Intel Maple Ridge discrete Thunderbolt 4 controller
* A couple of cleanups and minor improvements.
-----BEGIN PGP SIGNATURE-----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=+RXF
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.11 merge window
This includes following Thunderbolt/USB4 changes for v5.11 merge window:
* DMA traffic test driver
* USB4 router NVM upgrade improvements
* USB4 router operations proxy implementation available in the recent
Intel Connection Manager firmwares
* Support for Intel Maple Ridge discrete Thunderbolt 4 controller
* A couple of cleanups and minor improvements.
* tag 'thunderbolt-for-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (22 commits)
thunderbolt: Add support for Intel Maple Ridge
thunderbolt: Add USB4 router operation proxy for firmware connection manager
thunderbolt: Move constants for USB4 router operations to tb_regs.h
thunderbolt: Add connection manager specific hooks for USB4 router operations
thunderbolt: Pass TX and RX data directly to usb4_switch_op()
thunderbolt: Pass metadata directly to usb4_switch_op()
thunderbolt: Perform USB4 router NVM upgrade in two phases
thunderbolt: Return -ENOTCONN when ERR_CONN is received
thunderbolt: Keep the parent runtime resumed for a while on device disconnect
thunderbolt: Log adapter numbers in decimal in path activation/deactivation
thunderbolt: Log which connection manager implementation is used
thunderbolt: Move max_boot_acl field to correct place in struct icm
MAINTAINERS: Add Isaac as maintainer of Thunderbolt DMA traffic test driver
thunderbolt: Add DMA traffic test driver
thunderbolt: Add support for end-to-end flow control
thunderbolt: Make it possible to allocate one directional DMA tunnel
thunderbolt: Create debugfs directory automatically for services
thunderbolt: Add functions for enabling and disabling lane bonding on XDomain
thunderbolt: Add link_speed and link_width to XDomain
thunderbolt: Create XDomain devices for loops back to the host
...
Intel USB4 host routers that run the firmware based connection manager
(ICM) may implement a proxy for USB4 router operations. This is to avoid
the firmware to race with the OS driver, as both may need to run these
operations.
This adds two new connection manager specific callbacks which, if
provided, get called instead of the native USB4 router operation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The currect code expects that the router returns back the status of the
NVM authentication immediately. When tested against a real USB4 device
what happens is that the router is reset and only after that the result
is updated in the ROUTER_CS_26 register status field. This also seems to
align better what the spec suggests.
For this reason do the same what we already do with the Thunderbolt 3
devices and perform the NVM upgrade in two phases. First start the
NVM_AUTH router operation and once the router is added back after the
reset read the status in ROUTER_CS_26 and expose it to the userspace
accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This allows service drivers to use it as parent directory if they need
to add their own debugfs entries.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These can be used by service drivers to enable and disable lane bonding
as needed.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link speed and link width are needed for checking expected values in
case of using a loopback service.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tiger Lake-H has the same Thunderbolt/USB4 controller as Tiger
Lake-LP. Add the Tiger Lake-H PCI IDs to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=KvWM
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
This adds a bit more build coverage for the tests even though these are
not expected to be enabled by normal users and distros. In order to make
this working we need to open-code kunit_test_suite() and call the
relevant functions directly in the driver init/exit hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the kernel power management documentation freeze phase
should only quiesce the device, no need to configure wakes or put it to
low power state. For this reason we simply stop the control channel and
in case of Software Connection Manager also mark the hotplug disabled.
This should align the driver better with the PM framework expectations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds debugfs interface that can be used for debugging possible
issues in hardware/software. It exposes router and adapter config spaces
through files like this:
/sys/kernel/debug/thunderbolt/<DEVICE>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters
...
The "regs" is either the router or port configuration space register
dump. The "path" is the port path configuration space and "counters" is
the optional counters configuration space.
These files contains one register per line so it should be easy to use
normal filtering tools to find the registers of interest if needed.
The router and adapter regs file becomes writable when
CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done
in production systems) and in this case the developer can write "offset
value" lines there to modify the hardware directly. For convenience this
also supports the long format the read side produces (but ignores the
additional fields). The counters file can be written even when
CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear
the counter values.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Tiger Lake from other controllers.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Ice Lake from other controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With USB4 there will be other vendors so make sure the current checks
for different Intel controllers will not accidentally match those.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is useful if one needs to check if adapter (port) is the host
interface (NHI). Make tb_port_alloc_hopid() take advantage of this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is similar to tb_port_next_cap() but instead allows walking
capability list of a switch (router). Convert tb_switch_find_cap() and
tb_switch_find_vse_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is useful for walking port config space (adapter)
capability lists. Convert the tb_port_find_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds runtime PM support for the Software Connection Manager parts
of the driver. This allows to save power when either there is no device
attached at all or there is a device attached and all following
conditions are true:
- Tunneled PCIe root/downstream ports are runtime suspended
- Tunneled USB3 ports are runtime suspended
- No active DisplayPort stream
- No active XDomain connection
For the first two we take advantage of device links that were added in
previous patch. Difference for the system sleep case is that we also
enable wakes when something is geting plugged in/out of the Thunderbolt
ports.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The new way to describe relationship between tunneled ports and USB4 NHI
(Native Host Interface) is with ACPI _DSD looking like below for a PCIe
downstream port:
Scope (\_SB.PCI0)
{
Device (NHI0) { } // Thunderbolt NHI
Device (DSB0) // Hotplug downstream port
{
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"usb4-host-interface", \_SB.PCI0.NHI0},
...
}
})
}
}
This is "documented" in these [1] USB-IF slides and being used on
systems that ship with Windows.
The _DSD can be added to tunneled USB3 and PCIe ports, and is needed to
make sure the USB4 NHI is resumed before any of the tunneled ports so
the protocol tunnels get established properly before the actual port
itself is resumed. Othwerwise the USB/PCI core find the link may not be
established and starts tearing down the device stack.
This parses the ACPI description each time NHI is probed and tries to
find devices that has the property and it references the NHI in
question. For each matching device a device link from that device to the
NHI is created.
Since USB3 ports themselves do not get runtime suspended with the parent
device (hub) we do not add the link from the USB3 port to USB4 NHI but
instead we add the link from the xHCI device. This makes the device link
usable for runtime PM as well.
[1] https://www.usb.org/sites/default/files/D1T2-2%20-%20USB4%20on%20Windows.pdf
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order for the router and the whole domain to wake up from system
suspend states we need to enable wakes for the connected routers. For
device routers we enable wakes from PCIe and USB 3.x. This allows
devices such as keyboards connected to USB 3.x hub that is tunneled to
wake the system up as expected. For all routers we enabled wake on USB4
for each connected ports. This is used to propagate the wake from router
to another.
Do the same for legacy routers through link controller vendor specific
registers as documented in USB4 spec chapter 13.
While there correct kernel-doc of usb4_switch_set_sleep() -- it does not
enable wakes instead there is a separate function (usb4_switch_set_wake())
that does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the port is connected to another host it should be marked as such
in the USB4 port capability. This information is used by the router
during sleep and wakeup.
Also do the same for legacy switches via link controller vendor specific
registers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both ends of the link needs to have this set. Otherwise the link is not
re-established properly after sleep. Now since it is possible to have
mixed USB4 and Thunderbolt 1, 2 and 3 devices we need to split the link
configuration functionality to happen per port so we can pick the
correct implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
First generation routers may need the reset command upon resume but it
is not supported by newer generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 4caf2511ec ("thunderbolt: Add trivial .shutdown") exposes a bug
in the Thunderbolt driver, that frees an unallocated id, resulting in the
following spinlock bad magic bug.
[ 20.633803] BUG: spinlock bad magic on CPU#4, halt/3313
[ 20.640030] lock: 0xffff92e6ad5c97e0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 20.672139] Call Trace:
[ 20.675032] dump_stack+0x97/0xdb
[ 20.678950] ? spin_bug+0xa5/0xb0
[ 20.682865] do_raw_spin_lock+0x68/0x98
[ 20.687397] _raw_spin_lock_irqsave+0x3f/0x5d
[ 20.692535] ida_destroy+0x4f/0x124
[ 20.696657] tb_switch_release+0x6d/0xfd
[ 20.701295] device_release+0x2c/0x7d
[ 20.705622] kobject_put+0x8e/0xac
[ 20.709637] tb_stop+0x55/0x66
[ 20.713243] tb_domain_remove+0x36/0x62
[ 20.717774] nhi_remove+0x4d/0x58
Fix the issue by disabling ports that are enabled as per the EEPROM, but
not implemented. While at it, update the kernel doc for the disabled
field, to reflect this.
Cc: stable@vger.kernel.org
Fixes: 4caf2511ec ("thunderbolt: Add trivial .shutdown")
Reported-by: Srikanth Nandamuri <srikanth.nandamuri@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>