The current code checks if abs(delta_delta.tv_sec) is greater or
equal to two before it discards the old delta value, but this can
trigger at close to -1 seconds since -1.000000001 seconds is stored
as tv_sec -2 and tv_nsec 999999999 in a normalized timespec.
rtc_resume had an early return check if the rtc value had not changed
since rtc_suspend. This effectivly stops time for the duration of the
short sleep. Check if sleep_time is positive after all the adjustments
have been applied instead since this allows the old_system adjustment
in rtc_suspend to have an effect even for short sleep cycles.
CC: stable@kernel.org
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
# echo $((`cat since_epoch`)+120) > wakealarm
# echo 0 > wakealarm
# poweroff
Fix this by disabling the alarm when there are no timers to run.
Cc: stable@kernel.org
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Real world year equals the value in vrtc YEAR register plus an offset.
We used 1960 as the offset to make leap year consistent, but for a
device's first use, its YEAR register is 0 and the system year will
be parsed as 1960 which is not a valid UNIX time and will cause many
applications to fail mysteriously. So we use 1972 instead to fix this
issue.
Updated patch which adds a sanity check suggested by Mathias
This isn't a change in behaviour for systems, because 1972 is the one we
actually use. It's the old version in upstream which is out of sync with
all devices.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Says Andrew:
"60 patches. That's good enough for -rc1 I guess. I have quite a lot
of detritus to be rechecked, work through maintainers, etc.
- most of the remains of MM
- rtc
- various misc
- cgroups
- memcg
- cpusets
- procfs
- ipc
- rapidio
- sysctl
- pps
- w1
- drivers/misc
- aio"
* akpm: (60 commits)
memcg: replace ss->id_lock with a rwlock
aio: allocate kiocbs in batches
drivers/misc/vmw_balloon.c: fix typo in code comment
drivers/misc/vmw_balloon.c: determine page allocation flag can_sleep outside loop
w1: disable irqs in critical section
drivers/w1/w1_int.c: multiple masters used same init_name
drivers/power/ds2780_battery.c: fix deadlock upon insertion and removal
drivers/power/ds2780_battery.c: add a nolock function to w1 interface
drivers/power/ds2780_battery.c: create central point for calling w1 interface
w1: ds2760 and ds2780, use ida for id and ida_simple_get() to get it
pps gpio client: add missing dependency
pps: new client driver using GPIO
pps: default echo function
include/linux/dma-mapping.h: add dma_zalloc_coherent()
sysctl: make CONFIG_SYSCTL_SYSCALL default to n
sysctl: add support for poll()
RapidIO: documentation update
drivers/net/rionet.c: fix ethernet address macros for LE platforms
RapidIO: fix potential null deref in rio_setup_device()
RapidIO: add mport driver for Tsi721 bridge
...
The driver is added using platform_driver_probe(), so the callbacks can be
discarded more aggessively.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add initial support for the microchip mcp7941x series of real time clocks.
The mcp7941x series is generally compatible with the ds1307 and ds1337 rtc
devices from dallas semiconductor. minor differences include a backup
battery enable bit, and the polarity of the oscillator enable bit.
Signed-off-by: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the one use of an ida that doesn't retry on receiving -EAGAIN.
I'm assuming do so will cause no harm and may help on a rare occasion.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The module.h was implicitly everywhere, but when we clean
that up, the implicit users will compile fail; fix them up
in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The driver does not generate an alarm interrupt even though a time for
an alarm is set.
This results from disabling rtc_clk after setting the alarm time.
To generate an alarm interrupt the driver should maintain its enabled
state for rtc_clk the until alarm interrupt occurs. This patch permits
generation of an alarm interrupt.
[akpm@linux-foundation.org: make s3c_rtc_alarm_clk_lock local to s3c_rtc_alarm_clk_enable()]
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/sched.h to fix below build error.
CC drivers/rtc/rtc-imxdi.o
drivers/rtc/rtc-imxdi.c: In function 'di_write_wait':
drivers/rtc/rtc-imxdi.c:168: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/rtc/rtc-imxdi.c:168: error: (Each undeclared identifier is reported only once
drivers/rtc/rtc-imxdi.c:168: error: for each function it appears in.)
drivers/rtc/rtc-imxdi.c:168: error: implicit declaration of function 'signal_pending'
drivers/rtc/rtc-imxdi.c:168: error: implicit declaration of function 'schedule_timeout'
drivers/rtc/rtc-imxdi.c: In function 'dryice_norm_irq':
drivers/rtc/rtc-imxdi.c:329: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
rtc: twl: Fix registration vs. init order
rtc: Initialized rtc_time->tm_isdst
rtc: Fix RTC PIE frequency limit
rtc: rtc-twl: Remove lockdep related local_irq_enable()
rtc: rtc-twl: Switch to using threaded irq
rtc: ep93xx: Fix 'rtc' may be used uninitialized warning
alarmtimers: Avoid possible denial of service with high freq periodic timers
alarmtimers: Memset itimerspec passed into alarm_timer_get
alarmtimers: Avoid possible null pointer traversal
Only register as an RTC device after the hardware has been
successfully initialized. The RTC class driver will call
back to this driver to read a pending alarm, and other
drivers watching for new devices on the RTC class may
read the RTC time upon registration. Such access might
occur while the RTC is stopped, prior to clearing
pending alarms, etc.
The new ordering also avoids leaving the platform
device drvdata set to an unregistered struct rtc_device *
on probe errors.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Even though the Linux kernel does not use the tm_isdst field, it is
exposed as part of the ABI. This field can accidentally be left
initialized, which is why we currently memset buffers returned to
userland in rtc_read_time.
There is a case however where the field can return garbage from the
stack though when using the RTC_ALM_READ ioctl on the rtc device. This
ioctl invokes rtc_read_alarm, which is careful to memset the rtc_wkalrm
buffer that is copied to userland, but it then uses a struct copy to
assign to alarm->time given the return value from rtc_ktime_to_tm().
rtc_ktime_to_tm() is implemented by calling rtc_time_to_tm using a
derivative seconds counds from ktime, but rtc_time_to_tm does not assign
a value to ->tm_isdst. This results in garbage from rtc_ktime_to_tm()'s
frame ending up being copied out to userland as part of the returned
rtc_wkalrm.
Fix this by initializing rtc_time->tm_isdst to 0 in rtc_time_to_tm.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The previous rtc-s3c had two issues related with its IRQ.
1. Users cannot open rtc multiple times because an open operation
calls request_irq on the same IRQ. (e.g., two user processes wants to
open and read RTC time from rtc-s3c at the same time)
2. If alarm is set and no one has the rtc opened with filesystem
(either the alarm is set by kernel/boot-loader or user set an alarm and
closed rtc dev file), the pending bit is not cleared and no further
interrupt is invoked. When the alarm is used by the system itself such
as a resume from suspend-to-RAM or other Low-power modes/idle, this is
a critical issue.
This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Limit RTC PIE frequency
rtc: Fix hrtimer deadlock
rtc: Handle errors correctly in rtc_irq_set_state()
Fixup trivial conflicts in drivers/rtc/interface.c due to slightly
trivially versions of the same patch coming in two different ways.
Thomas earlier submitted a fix to limit the RTC PIE freq, but
picked 5000Hz out of the air. Willy noticed that we should
instead use the 8192Hz max from the rtc man documentation.
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that the irq is properly threaded (due to it needing i2c access)
we should also remove the local_irq_enable() call in twl_rtc_interrupt.
Testing this with Pandaboard, the RTC is still working.
[Reworked commit message -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The driver is accessing to i2c bus in interrupt handler.
Therefore, it should use threaded irq.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
commit 92d921c5d "rtc: ep93xx: Initialize drvdata before registering device"
ensures the drvdata is initialized prior to registering the rtc device.
But it set the drvdata to an uninitialized pointer.
Thus calling platform_get_drvdata in ep93xx_rtc_remove does not get correct address.
This patch fixes below warning by adding struct rtc_device *rtc to struct ep93xx_rtc.
Then set platform drvdata to ep93xx_rtc instead of rtc.
CC drivers/rtc/rtc-ep93xx.o
drivers/rtc/rtc-ep93xx.c: In function 'ep93xx_rtc_probe':
drivers/rtc/rtc-ep93xx.c:154: warning: 'rtc' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
As the comment explains, the intention of the code is to clear the
OMAP_RTC_CTRL_MODE_12_24 bit, but instead it only clears the
OMAP_RTC_CTRL_SPLIT and OMAP_RTC_CTRL_AUTO_COMP bits, which should be
kept. OMAP_RTC_CTRL_DISABLE, OMAP_RTC_CTRL_SET_32_COUNTER,
OMAP_RTC_CTRL_TEST, and OMAP_RTC_CTRL_ROUND_30S are also better off
being cleared.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben reported a lockup related to rtc. The lockup happens due to:
CPU0 CPU1
rtc_irq_set_state() __run_hrtimer()
spin_lock_irqsave(&rtc->irq_task_lock) rtc_handle_legacy_irq();
spin_lock(&rtc->irq_task_lock);
hrtimer_cancel()
while (callback_running);
So the running callback never finishes as it's blocked on
rtc->irq_task_lock.
Use hrtimer_try_to_cancel() instead and drop rtc->irq_task_lock while
waiting for the callback. Fix this for both rtc_irq_set_state() and
rtc_irq_set_freq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the hrtimer self rearming mode a user can DoS the machine simply
because it's starved by hrtimer events.
The RTC hrtimer is self rearming. We really need to limit the frequency
to something sensible.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ben Greear <greearb@candelatech.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code checks the correctness of the parameters, but unconditionally
arms/disarms the hrtimer.
The result is that a random task might arm/disarm rtc timer and surprise
the real owner by either generating events or by stopping them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ben Greear <greearb@candelatech.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC pie hrtimer is self rearming. We really need to limit the
frequency to something sensible. Thus limit it to the 8192Hz max
value from the rtc man documentation
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[jstultz: slightly reworked to use RTC_MAX_FREQ value]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Ben reported a lockup related to rtc. The lockup happens due to:
CPU0 CPU1
rtc_irq_set_state() __run_hrtimer()
spin_lock_irqsave(&rtc->irq_task_lock) rtc_handle_legacy_irq();
spin_lock(&rtc->irq_task_lock);
hrtimer_cancel()
while (callback_running);
So the running callback never finishes as it's blocked on
rtc->irq_task_lock.
Use hrtimer_try_to_cancel() instead and drop rtc->irq_task_lock while
waiting for the callback. Fix this for both rtc_irq_set_state() and
rtc_irq_set_freq().
Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In rtc_irq_set_state, the code checks the correctness of the parameters,
but then goes on to unconditionally arms/disarms the hrtimer. Thus a
random task might arm/disarm rtc timer and surprise the real owner by
either generating events or by stopping them.
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
Using __SPIN_LOCK_UNLOCKED for a dynamically allocated lock is wrong and
breaks the build with PREEMPT_RT_FULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Chew <achew@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We forget to save the return value of the call to
twl_rtc_write_u8(save_control, REG_RTC_CTRL_REG); in 'ret', making the
test of 'ret < 0' dead code since 'ret' then couldn't possibly have
changed since the last test just a few lines above. It also makes us not
detect failures from that specific twl_rtc_write_u8() call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Rusev <source@mvista.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for PMIC8xxx based RTC. PMIC8xxx is Qualcomm's power
management IC that internally houses an RTC module. This driver
communicates with the PMIC module over SSBI bus.
[akpm@linux-foundation.org: cosmetic tweaks]
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for clock gating. Power consumption can be reduced by setting
rtc_clk disabled state except for when RTC related registers are accessed.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MPC5200B contains a limited version of RTC from MPC5121. Add support for
the RTC on that CPU.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'timers-rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Serialize EFI time accesses on rtc_lock
x86: Serialize SMP bootup CMOS accesses on rtc_lock
rtc: stmp3xxx: Remove UIE handlers
rtc: stmp3xxx: Get rid of mach-specific accessors
rtc: stmp3xxx: Initialize drvdata before registering device
rtc: stmp3xxx: Port stmp-functions to mxs-equivalents
rtc: stmp3xxx: Restore register definitions
rtc: vt8500: Use define instead of hardcoded value for status bit
The RTC core handles UIE since 6610e08 (RTC: Rework RTC code to use
timerqueue for events), so remove the specific interrupt in this driver.
To make it work at all, enable interrupts in set_alarm() if needed. Drop
IRQF_DISABLED which is deprecated, while we are here. Finally, add my
copyright after all these changes.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Replace the accessors with standard readl/writel to remove their
platform-dependency. Also, drop __raw_(read|write)l-accessors while we
are here.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The stmp3xxx driver used to include functions from a stmp-specific
include. Because of consolidation, plat-stmp has now been removed and
merged with the compatible mach-mxs.
Use the apropriate mxs-functions for transition. The accessors will be
converted to readl/writel in a later patch.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The stmp3xxx driver used to include register names from a stmp-specific
include. Because of consolidation, plat-stmp has now been removed and
merged with the compatible mach-mxs. Restore the register names directly
in the driver and rename them to be specific to this driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Fixes the vt8500 driver to use a define value for the isr
is-alarm bit.
Cc: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
PT7C4338 chip is being manufactured by Pericom Technology Inc. It is a
serial real-time clock which provides:
1) Low-power clock/calendar.
2) Programmable square-wave output.
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the generic code handles UIE mode irqs via periodic
alarm interrupts, no one calls the
rtc_class_ops->update_irq_enable() method anymore.
Further the rtc_class_ops doesn't have a update_irq_enable element
anymore, so this causes a build error.
This patch removes the driver hooks and implementations of
update_irq_enable and the associated setup.
[wsa: updated commit-message and removed update_irq_enable-function, too]
[jstultz: improve commit message, clarifying build issue]
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Because the RTC interface is only a second granular interface,
each time we read from the RTC for suspend/resume, we introduce a
half second (on average) of error.
In order to avoid this error accumulating as the system is suspended
over and over, this patch measures the time delta between the RTC
and the system CLOCK_REALTIME.
If the delta is less then 2 seconds from the last suspend, we compensate
by using the previous time delta (keeping it close). If it is larger
then 2 seconds, we assume the clock was set or has been changed, so we
do no correction and update the delta.
Note: If NTP is running, ths could seem to "fight" with the NTP corrected
time, where as if the system time was off by 1 second, and NTP slewed the
value in, a suspend/resume cycle could undo this correction, by trying to
restore the previous offset from the RTC. However, without this patch,
since each read could cause almost a full second worth of error, its
possible to get almost 2 seconds of error just from the suspend/resume
cycle alone, so this about equal to any offset added by the compensation.
Further on systems that suspend/resume frequently, this should keep time
closer then NTP could compensate for if the errors were allowed to
accumulate.
Credits to Arve Hjønnevåg for suggesting this solution.
This patch also improves some of the variable names and adds more clear
comments.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The patch moves rtc driver for PKUnity-v3 SoC from arch/unicore32/kernel/
to drivers/rtc/, with renaming it to rtc-puv3.c.
Also, Kconfig, Makefile, and MAINTAINERS are modified correspondingly.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
One new offender detected by the recently increased type checking in
platform_get_drvdata():
drivers/rtc/rtc-m41t93.c: In function ‘m41t93_remove’:
drivers/rtc/rtc-m41t93.c:192: warning: passing argument 1 of ‘platform_get_drvdata’ from incompatible pointer type
Use spi_get_drvdata() instead of platform_get_drvdata(), cfr. commit
42fea15d6d ("spi/rtc-{ds1390,ds3234,m41t94}:
Use spi_get_drvdata() for SPI devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's not referenced outside this file so there's no need for it to be in
the global namespace and sparse warns about that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Bryan Henderson noticed that the "RTC: Fix rtc driver ioctl specific
shortcutting" commit has a small bug: When an ioctl is called with an
invalid command code and the clock driver does not have an "ioctl"
method, the ioctl returns rc 0 instead of -ENOTTY.
This patch fixes the issue.
CC: Bryan Henderson <bryanh@giraffe-data.com>
CC: Gabor Z. Papp <gzp@papp.hu>
Reported-by: Bryan Henderson <bryanh@giraffe-data.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit 51ba60c5 ("RTC: Cleanup rtc_class_ops->update_irq_enable()")
removed the only user of the update IRQ, so there is no need to manage it
any more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memory allocated using request_mem_region should be released using
release_mem_region, not release_region.
The semantic patch that fixes part of this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2,E3;
@@
request_mem_region(E1,E2,E3)
...
?- release_region(E1,E2)
+ release_mem_region(E1,E2)
// </smpl>
[akpm@linux-foundation.org: use resource_size()]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add basic support for ST m41t93 SPI RTCs. Tested with factory-new and
with "run-in" species with and without backup batteries.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for EM Microelectronic EM3027 RTC chip.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the RTC devices in VIA and WonderMedia
Systems-on-Chip. Alarm, 1Hz interrupts, reading and setting time are
supported.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (26 commits)
arch/tile: prefer "tilepro" as the name of the 32-bit architecture
compat: include aio_abi.h for aio_context_t
arch/tile: cleanups for tilegx compat mode
arch/tile: allocate PCI IRQs later in boot
arch/tile: support signal "exception-trace" hook
arch/tile: use better definitions of xchg() and cmpxchg()
include/linux/compat.h: coding-style fixes
tile: add an RTC driver for the Tilera hypervisor
arch/tile: finish enabling support for TILE-Gx 64-bit chip
compat: fixes to allow working with tile arch
arch/tile: update defconfig file to something more useful
tile: do_hardwall_trap: do not play with task->sighand
tile: replace mm->cpu_vm_mask with mm_cpumask()
tile,mn10300: add device parameter to dma_cache_sync()
audit: support the "standard" <asm-generic/unistd.h>
arch/tile: clarify flush_buffer()/finv_buffer() function names
arch/tile: kernel-related cleanups from removing static page size
arch/tile: various header improvements for building drivers
arch/tile: disable GX prefetcher during cache flush
arch/tile: tolerate disabling CONFIG_BLK_DEV_INITRD
...
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: Make lookup table const
RTC: Disable CONFIG_RTC_CLASS from being built as a module
timers: Fix alarmtimer build issues when CONFIG_RTC_CLASS=n
timers: Remove delayed irqwork from alarmtimers implementation
timers: Improve alarmtimer comments and minor fixes
timers: Posix interface for alarm-timers
timers: Introduce in-kernel alarm-timer interface
timers: Add rb_init_node() to allow for stack allocated rb nodes
time: Add timekeeping_inject_sleeptime
This is a simple RTC driver that lets Tilera hardware boot up and
set the clock correctly.
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The driver is not balancing set_irq and disable_irq_wake() calls, so
ensure that it keeps track of whether the wake is enabled.
The fixes the following error on S3C6410 devices:
WARNING: at kernel/irq/manage.c:382 set_irq_wake+0x84/0xec()
Unbalanced IRQ 92 wake disable
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit f44f7f9 (RTC: Initialize kernel state from RTC)
rtc_device_register reads the programmed alarm. As reading the alarm
needs to take the mc13xxx lock, release it before calling
rtc_device_register.
This fixes a deadlock during boot:
INFO: task swapper:1 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
swapper D c02b175c 0 1 0 0x00000000
[<c02b175c>] (schedule+0x304/0x4f4) from [<c02b25a8>] (__mutex_lock_slowpath+0x7c/0x110)
[<c02b25a8>] (__mutex_lock_slowpath+0x7c/0x110) from [<c020b4cc>] (mc13xxx_rtc_read_time+0x1c/0x118)
[<c020b4cc>] (mc13xxx_rtc_read_time+0x1c/0x118) from [<c0208f04>] (__rtc_read_time+0x58/0x5c)
[<c0208f04>] (__rtc_read_time+0x58/0x5c) from [<c0209508>] (rtc_read_time+0x30/0x48)
[<c0209508>] (rtc_read_time+0x30/0x48) from [<c0209dd4>] (__rtc_read_alarm+0x1c/0x290)
[<c0209dd4>] (__rtc_read_alarm+0x1c/0x290) from [<c0208d58>] (rtc_device_register+0x150/0x27c)
[<c0208d58>] (rtc_device_register+0x150/0x27c) from [<c02b0b74>] (mc13xxx_rtc_probe+0x128/0x17c)
[<c02b0b74>] (mc13xxx_rtc_probe+0x128/0x17c) from [<c01d5280>] (platform_drv_probe+0x1c/0x24)
[<c01d5280>] (platform_drv_probe+0x1c/0x24) from [<c01d3e58>] (driver_probe_device+0x80/0x1a8)
[<c01d3e58>] (driver_probe_device+0x80/0x1a8) from [<c01d400c>] (__driver_attach+0x8c/0x90)
[<c01d400c>] (__driver_attach+0x8c/0x90) from [<c01d3654>] (bus_for_each_dev+0x60/0x8c)
[<c01d3654>] (bus_for_each_dev+0x60/0x8c) from [<c01d2f6c>] (bus_add_driver+0x180/0x248)
[<c01d2f6c>] (bus_add_driver+0x180/0x248) from [<c01d4664>] (driver_register+0x70/0x15c)
[<c01d4664>] (driver_register+0x70/0x15c) from [<c01d5700>] (platform_driver_probe+0x18/0x98)
[<c01d5700>] (platform_driver_probe+0x18/0x98) from [<c00273a8>] (do_one_initcall+0x2c/0x168)
[<c00273a8>] (do_one_initcall+0x2c/0x168) from [<c00083ac>] (kernel_init+0xa0/0x150)
[<c00083ac>] (kernel_init+0xa0/0x150) from [<c0033ff8>] (kernel_thread_exit+0x0/0x8)
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Closes: http://bugs.debian.org/625804
[Tweaked commit log -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the clientdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the clientdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[Fixed up commit log -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[fixed up commit log -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") uncovered
an issue in a number of RTC drivers, where the drivers call
rtc_device_register before initializing the device or platform drvdata.
This frequently results in null pointer dereferences when the
rtc_device_register immediately makes use of the rtc device, calling
rtc_read_alarm.
The solution is to ensure the drvdata is initialized prior to registering
the rtc device.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: rtc-linux@googlegroups.com
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[fixed up commit log -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The RTC subsystem has a number of accessors that are available via
include/linux/rtc.h. However many of these interfaces are not
available for use if CONFIG_RTC_CLASS=m.
So in order to support wider use of the RTC in the kernel, I'm
removing the tristate config option for a bool, so that code can
easily be conditionalized if the RTC class is present or not.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We call rtc_read_alarm from rtc_device_register, so it is important
that the rtc device is fully initialized prior to registration.
rtc-max8925 sets drvdata after register, so the rtc_read_alarm code
dereferences a NULL pointer.
Call dev_set_drvdata before rtc_device_register.
[ jstultz/tglx: Massaged commit message ]
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Link: http://lkml.kernel.org/r/%3C1303929869-25249-1-git-send-email-john.stultz%40linaro.org%3E
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some platforms cannot implement read_persistent_clock, as
their RTC devices are only accessible when interrupts are enabled.
This keeps them from being used by the timekeeping code on resume
to measure the time in suspend.
The RTC layer tries to work around this, by calling do_settimeofday
on resume after irqs are reenabled to set the time properly. However,
this only corrects CLOCK_REALTIME, and does not properly adjust
the sleep time value. This causes btime in /proc/stat to be incorrect
as well as making the new CLOCK_BOTTTIME inaccurate.
This patch resolves the issue by introducing a new timekeeping hook
to allow the RTC layer to inject the sleep time on resume.
The code also checks to make sure that read_persistent_clock is
nonfunctional before setting the sleep time, so that should the RTC's
HCTOSYS option be configured in on a system that does support
read_persistent_clock we will not increase the total_sleep_time twice.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The rtc_device_register() call has changed semantics so that it
will immediately call out to rtc_read_alarm() and since the
callbacks require the drvdata to be set, we need to set it before
the registration call to avoid NULL dereference.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In omap_rtc_probe error path, free_irq() was using NULL rather than the
driver data as the data pointer so free_irq() wouldn't have matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Link: http://lkml.kernel.org/r/%3C1303005778.2889.2.camel%40phoenix%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") caused a
boot regression on the MRST platform.
The reason is that rtc_device_register() calls rtc_read_alarm() after
that change, which function does not have all driver data set up yet.
The rtc-mrst driver needs to call dev_set_drvdata() before rtc_device_register()
gets called.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140384-27571-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit f44f7f96a2 (RTC: Initialize kernel state from RTC) will
call rtc_read_alarm() inside rtc_device_register(), so rtc-mrst
driver need to call dev_set_drvdata() before rtc_device_register()
get called.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Fix the following section mismatch warning.
WARNING: drivers/rtc/built-in.o(.data+0xa0): Section mismatch in reference from the variable vrtc_mrst_platform_driver to the function .init.text:vrtc_mrst_platform_probe()
The variable vrtc_mrst_platform_driver references the function __init vrtc_mrst_platform_probe()
If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new bfin_rtc_alarm_irq_enable function forgot to add a "return 0" to
the end leading to the build warning:
drivers/rtc/rtc-bfin.c: In function 'bfin_rtc_alarm_irq_enable':
drivers/rtc/rtc-bfin.c:253: warning: control reaches end of non-void function
CC: stable@kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
s3c_rtc_setpie was removed, and it resulted in compiler error:
drivers/rtc/rtc-s3c.c: In function s3c_rtc_release
drivers/rtc/rtc-s3c.c:339:2: error: implicit declaration of function
s3c_rtc_setpie
Fix it by removing s3c_rtc_release calls.
[jstultz: An identical fix was also sent in by Jiri Pinkava
<jiri.pinkava@vscht.cz>]
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Arve Hjønnevåg
Rabin Vincent
Dave Martin
Axel Lin
Feng Tang
Linus Torvalds
Uwe Kleine-König
David Anders
Jonathan Cameron
Al Viro
Paul Gortmaker
Donggeun Kim
Todd Poynor
Mike Waychison
MyungJoo Ham
John Stultz
Sebastian Reichel
Ilkka Koskinen
Daniel Glöckner
Thomas Gleixner
Jesper Juhl
Anirudh Ghayal
Dmitry Eremin-Solenikov
Jiri Kosina
Wolfram Sang
Priyanka Jain
Alexey Charkov
Joe Perches
Guan Xuetao
Geert Uytterhoeven
Mark Brown
Lars-Peter Clausen
Rajeev Kumar
Julia Lawall
Voss, Nikolaus
Heiko Schocher
Mike Rapoport
Haojian Zhuang
Chris Metcalf
Ben Dooks
Zhangfei Gao
Linus Walleij
Major Lee
Lucas De Marchi
Mike Frysinger
Vasily Khoruzhick