Set microphone pins 0x18 (rear) and 0x19 (front) to VREF_50 to fix the
microphone noise on ASUS TUF B550M-PLUS which uses the ALCS1200A codec.
The initial value was VREF_80.
The same issue is also present on Windows using both the default Windows
driver and all tested Realtek drivers before version 6.0.9049.1. Comparing
Realtek driver 6.0.9049.1 (the first one without the microphone noise) to
Realtek driver 6.0.9047.1 (the last one with the microphone noise)
revealed that the fix is the result of setting pins 0x18 and 0x19 to
VREF_50.
This fix may also work for other boards that have been reported to have
the same microphone issue and use the ALC1150 and ALCS1200A codecs, since
these codecs are similar and the fix in the Realtek driver on Windows is
common for both. However, it is currently enabled only for ASUS TUF
B550M-PLUS as this is the only board that could be tested.
Signed-off-by: Marios Levogiannis <marios.levogiannis@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220530074131.12258-1-marios.levogiannis@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the PCI ID for X-Fi cards sold under the Platnum and XtremeMusic names
Before: snd_ctxfi 0000:05:05.0: chip 20K1 model Unknown (1102:0021) is found
After: snd_ctxfi 0000:05:05.0: chip 20K1 model SB046x (1102:0021) is found
[ This is only about defining the model name string, and the rest is
handled just like before, as a default unknown device.
Edward confirmed that the stuff has been working fine -- tiwai ]
Signed-off-by: Edward Matijevic <motolav@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/cae7d1a4-8bd9-7dfe-7427-db7e766f7272@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
GCC 12 sees that it's technically possible for num_streams to be larger
than ARRAY_SIZE(pcm->streams). Bounds-check the iterator.
../sound/pci/lola/lola_pcm.c: In function 'lola_pcm_update':
../sound/pci/lola/lola_pcm.c:567:64: warning: array subscript [0, 31] is outside array bounds of 'struct lola_stream[16]' [-Warray-bounds]
567 | struct lola_stream *str = &pcm->streams[i];
| ~~~~~~~~~~~~^~~
In file included from ../sound/pci/lola/lola_pcm.c:15:
../sound/pci/lola/lola.h:307:28: note: while referencing 'streams'
307 | struct lola_stream streams[MAX_STREAM_COUNT];
| ^~~~~~~
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220520165537.2139826-1-keescook@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will be used to identify ALSA controls and firmware.
The Amp Name will be a channel identifier (L or R), and an
index, which identifies which amp for that channel.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-10-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CLSA0100 Laptop does not contain configuration inside ACPI,
instead the hardware configuration needs to be hardcoded.
Hardcode GPIO2 Interrupt in the driver for CSLA0100.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-6-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CS35L41 can produce interrupts on error.
When the interrupts occur, the driver will report
the error, but errors will only be fixed after playback
finishes.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-5-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This API was required for CLSA0100 laptop, which did not
have correct properties inside ACPI. The required values
are now hardcoded inside the driver so this is no longer
needed.
Without this api, there CLSA0100 can now use the generic
cs35l41 fixup, like the other laptops.
All other laptops will read the Speaker Position from
ACPI and set the channel map from within the driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-4-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop does not contain required properties inside ACPI,
instead the values are be hardcoded inside the driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-3-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For consistency, rename spi cs35l41 hda driver name so that
it matches i2c.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-2-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteBook 630 is using ALC236 codec which used 0x02 to control mute LED
and 0x01 to control micmute LED. Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220513121648.28584-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for a Speaker Playback Switch, which disables
the Amp connected to cs8409. The Switch is not added
automatically because cs8409 does not have an output amp
for the speaker NID.
Note: This switch uses a different GPIO to Cyborg/Odin variants
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220511100207.1268321-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for a Speaker Playback Switch, which disables
the Amp connected to cs8409. The Switch is not added
automatically because cs8409 does not have an output amp
for the speaker NID.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220511100207.1268321-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some board revisions of the Framework Laptop have an ALC295 with a
disconnected or faulty headset mic presence detect.
The "dell-headset-multi" fixup addresses this issue, but also enables an
inoperative "Headphone Mic" input device whenever a headset is
connected.
Adding a new quirk chain specific to the Framework Laptop resolves this
issue. The one introduced here is based on the System76 "no headphone
mic" quirk chain.
The VID:PID f111:0001 have been allocated to Framework Computer for this
board revision.
Revision history:
- v2: Moved to a custom quirk chain to suppress the "Headphone Mic"
pincfg.
Signed-off-by: Dustin L. Howett <dustin@howett.net>
Link: https://lore.kernel.org/r/20220511010759.3554-1-dustin@howett.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Jack detection on CS42L42, detection is normally done using
"auto" mode, which automatically detects what type of jack is
connected to the device. However, some headsets are not
automatically detected, and as such and alternative detection
method "manual mode" can be used to detect these headsets.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://lore.kernel.org/r/20220504161236.2490532-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pointer kctl is being assigned a value that is not being read, buf
is being re-assigned later. The assignment is redundant and can be
removed.
Cleans up clang scan build warning:
sound/pci/rme9652/hdsp.c:3317:28: warning: Although the value stored
to 'kctl' is used in the enclosing expression, the value is never
actually read from 'kctl' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220508212819.59188-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver is currently using ALC269_FIXUP_DELL4_MIC_NO_PRESENCE for
the Latitude 7520, but this fixup chain has some issues:
- The internal mic is really loud and the recorded audio is distorted
at "standard" audio levels.
- There are pop noises at system startup and when plugging/unplugging
headphone jacks.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215885
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Link: https://lore.kernel.org/r/20220501124237.4667-1-gabriele.mzt@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_PM is not enabled, alc_shutup() is not needed,
so move it inside the #ifdef CONFIG_PM guard.
Also drop some contiguous #endif / #ifdef CONFIG_PM for simplicity.
Fixes this build warning:
sound/pci/hda/patch_realtek.c:886:20: warning: unused function 'alc_shutup'
Fixes: 08c189f2c5 ("ALSA: hda - Use generic parser codes for Realtek driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220430193318.29024-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Yoga Duet 7 13ITL6 has Realtek ALC287 and built-in
speakers do not work out of the box. The fix developed for
Yoga 7i 14ITL5 also enables speaker output for this model.
Signed-off-by: Zihao Wang <wzhd@ustc.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220424084120.74125-1-wzhd@ustc.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On HP Laptops, requires the same ALC285_FIXUP_HP_GPIO_LED quirk to
make its audio LEDs work.
So apply the quirk, and make it the last one since it's an LED quirk.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Fixes: 07bcab9394 ("ALSA: hda/realtek: Add support for HP Laptops")
Link: https://lore.kernel.org/r/20220422090845.230071-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk ALC287_FIXUP_CS35L41_I2C_2 needs to chain the quirk
ALC269_FIXUP_THINKPAD_ACPI, otherwise the mute led will not work if a
thinkpad machine applies that quirk.
And it will be safe if non-thinkpad machines apply that quirk since
hda_fixup_thinkpad_acpi() will check and return in this case.
Fixes: ae7abe36e3 ("ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220422073937.10073-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On HP EliteBook 845 G9 and EliteBook 865 G9, the audio LEDs can be enabled by
ALC285_FIXUP_HP_MUTE_LED. So use it accordingly.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Fixes: 07bcab9394 ("ALSA: hda/realtek: Add support for HP Laptops")
Link: https://lore.kernel.org/r/20220421063606.39772-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes that came in since the merge window, plus one new
device ID for an x86 laptop. Nothing that really stands out with
particularly big impact outside of the affected device.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmJe0zgACgkQJNaLcl1U
h9CLqwf9Ge7xPY3HBe3v9046OOABeGeaeB8mwtiVj3erZrCeT46+U3V4QDc0P7Jp
Dc8ed+Wak16pCUEvuJN1kqoKzfFcYGgQmzj7hPMAPfbt5M07FmlptKxO9NEQrVsi
kk2G6w+1NyN3OEJJjykWS96dmzL4AMkDwCwkupkaJkZuFzkoA2I9x1Vql5UK+5gV
yk6CKoGVEh2cKixACQb/EF02+EDkv+Z+8Mo031b6JPagANi0m9g+pt8Rj7wMR5zp
XY0eaNQ6DaD+4RHhA98FTuSpvIVMOKTIwJA/pXxT1zm0dtjCARsD7/iv1Gr/DSiN
4/XkO0h5DgOtsuDFn0milr18fM0XLg==
=GZOq
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.18-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.18
A collection of fixes that came in since the merge window, plus one new
device ID for an x86 laptop. Nothing that really stands out with
particularly big impact outside of the affected device.
With commit 13046370c4 ("ALSA: hda/hdmi: let new platforms assign the
pcm slot dynamically"), old behaviour to consider the HDA pin number,
when choosing PCM to assign, was dropped.
Build on this change and limit the number of PCMs created to number of
converters (= maximum number of concurrent display/receivers) when
"mst_no_extra_pcms" and "dyn_pcm_no_legacy" quirks are both set.
Fix the check in hdmi_find_pcm_slot() to ensure only spec->pcm_used
entries are considered in the search. Elsewhere in the driver
spec->pcm_used is already checked properly.
Doing this avoids following warning at SOF driver probe for multiple
machine drivers:
[ 112.425297] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no
PCM in topology for HDMI converter 4
[ 112.425298] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no
PCM in topology for HDMI converter 5
[ 112.425299] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no
PCM in topology for HDMI converter 6
Fixes: 13046370c4 ("ALSA: hda/hdmi: let new platforms assign the pcm slot dynamically")
BugLink: https://github.com/thesofproject/linux/issues/2573
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220414150516.3638283-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
External boost enables sequences for devices with or without GPIO1 as
VSPK switch are the same if devices are put in safe mode from reset.
As a previous patch put all external boost devices into safe mode
from reset, all external boost devices can be handled in the same way
for stream open and close.
The only difference is that devices without an VSPK switch can not be
put in reset and devices with it can be put into reset if a
configuration is applied.
The function cs35l41_hda_safe_reset is created to handle the safe reset
of the chip, and as systems without VSPK switch are not supported
anymore, only the CS35L41 HDA driver should check its return.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-14-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For each case, only log the last regmap access, so it doesn't get
overwritten, and as all regmap access should show the same issues
logging the last one should be enough.
Change to dev_err to log this error.
Also, differentiate between a regmap access failure and invalid
playback action.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-13-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove cs35l41_hd_reg_sequence as it adds a layer of flexibility not needed.
As cs35l41_hda_(start/stop)_bst is a single register, it can be replaced by
regmap_update_bits with usleep_range to wait for the same 3000us that
reg_sequence had.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-12-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Having CS35L41_PWR_CTRL2 on cs35l41_hda_config overwrites the boost
configuration for internal boost.
So move it to the initialization part and use regmap_update_bits to
only change the correct bits.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-11-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To facilitate the configuration of external boost devices, put all
devices, with or without VSPK switch, into safe mode from the start.
That allows the following parts of the driver to handle all external
boost devices in the same way.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-8-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace vspk_always_on by a enum that better characterizes the boost
type, as there is 3 types of boost hardware.
And with the new boost type other parts of the driver can better handle
the configuration of the chip.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-7-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver can receive an empty hw_config, so mark as valid if
successfully read from device tree/ACPI or set by the driver itself.
Platforms not marked with a valid hw config will not be supported.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-3-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both ASoC and HDA require to configure the GPIOs and Boost, so
create a single shared struct for hardware configuration.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-2-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Marios Levogiannis
Xiang wangx
Rik van der Kemp
Kailang Yang
Julia Lawall
Edward Matijevic
Takashi Iwai
Kees Cook
Stefan Binding
Andy Chi
Werner Sembach
Dustin L. Howett
Colin Ian King
Gabriele Mazzotta
Randy Dunlap
bo liu
Zihao Wang
Hui Wang
Tim Crawford
Kai Vehmanen
Lucas Tanure