Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which
requires register range "ccb-mii" <0x18003000 0x1000>. This range
overlaps with MDIO cmd and param registers (<0x18003000 0x8>).
Essentially, the platform driver partly acts like a MDIO bus driver,
hence to use of this register range.
In some Northstar devices like Linksys EA9500, secondary switch is
connected via external MDIO. The only way to access and configure the
external switch is via MDIO bus. When we enable the MDIO bus in it's
current state, the MDIO bus and any child buses fail to register because
of the register range overlap.
On Northstar, the USB 3.0 PHY is connected at address 0x10 on the
internal MDIO bus. This change moves the usb3_phy node and makes it a
child node of internal MDIO bus.
Thanks to Rafał Miłecki's commit af850e14a7 ("phy: bcm-ns-usb3: add
MDIO driver using proper bus layer") the same USB 3.0 platform driver
can now act as USB 3.0 PHY MDIO driver.
Tested on Linksys Panamera (EA9500)
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There was a little conflict between the v4.11 bugfixes and the new changes for 4.12,
this merges the fixes into the 4.12 branch to avoid having to resolve it again.
* Broadcom fixes in mainline
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Memory starts at 0x80000000, not 0. 0 "works" due to mirrior of the
first 128M of RAM to that address. Anything greater than 128M will
quickly find nothing there. Correcting the starting address has
everything working again.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 7eb05f6d ("ARM: dts: bcm5301x: Add BCM SVK DT files")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The UARTs are outputting garbage on the console. This is due to a speed
issue. We can simply use the clock speed (which is now defined in the
DTSI file) and everything works fine.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: cdc36b22 ("ARM: dts: enable clock support for BCM5301X")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The iproc-qspi driver is the SPI driver that should be used going
forward. Modify the SPI DT entry to use this driver, and add an entry
in the bcm953012k DTS file to enable the SPI.
Tested on the bcm953012k board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the NAND entry in the DTS for the bcm953012k reference board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Every device tested so far got UART0 (at 0x18000300) working as serial
console. It's most likely part of reference design and all vendors use
it that way.
It seems to be easier to enable it by default and just disable it if we
ever see a device with different hardware design.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add device tree files for Broadcom Northstar based SVKs. Since the
bcm5301x.dtsi already exists, all that is necessary is the dts files to
enable the UARTs. With these files, the SVKs are able to boot to shell.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli
Rob Herring
Vivek Unune
Arnd Bergmann
Rafał Miłecki
Jon Mason
Jon Mason