By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Ido Shamay <idos@mellanox.com>
Fixes: d03a68f ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 0x0x prefix in an integer constant.
In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 0x0x prefix in an integer constant.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".
Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().
Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Introduce netif-msg to netvsc to control debug logging output
and keep msg_enable in netvsc_device_context so that it is
kept persistently.
2. Only call dump_rndis_message() when NETIF_MSG_RX_ERR or above
is specified in netvsc module debug param.
In non-debug mode, in current code, dump_rndis_message() will not
dump anything but it still initialize some local variables and
process the switch logic which is unnecessary, especially in
high network throughput situation.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During firmware restart, the quota command isn't calculated multiple
times, but after the firmware restart it has to be sent, so force it.
Otherwise the firmware crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I forgot to rename the CPTCFG_ prefix...
Fixes: 484b3d13b4 ("iwlwifi: mvm: add debugfs entry with the number of net-detect scans")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our device needs two different firmwares: the INIT firmware
and the operational (OPER) firmware. The first one is run
when the driver loads and it returns calibrations results
as well as the NVM. The second one implements the WiFi
protocol.
If the wlan interface is not brought up, the device is put
to low power state: no firmware will be running. When the
interface is brought up, we would run the OPER firmware
only and reuse the results of the run of the INIT firmware
when the driver was loaded. This is changing with this
patch.
We now run the INIT firmware every time mac80211 calls
start(). The penalty for that is minimal since the INIT
firwmare run fast. I now also avoid to power down the device
between the INIT and OPER firmware on certains buses.
The motivation for this change is that there are components
on the device (MFUART) that are triggered by the INIT
firmware and need the device to be powered up in order to
keep running. Powering the device down between the INIT and
OPER firmware would stop these components and prevent them
from running again since they are triggered by the INIT
firmware only.
The new flow allows this and also allows to trigger these
components again when the interface is brought up after
it has been brought down.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to
usb_control_msg() with a timeout value of 0. In some instances where the
interface is shutting down, this infinite wait results in a CPU deadlock. A
one second timeout fixes this problem without affecting any normal operations.
This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786.
Reported-by: Bernhard Wiedemann <bwiedemann@suse.com>
Tested-by: Bernhard Wiedemann <bwiedemann@suse.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Bernhard Wiedemann <bwiedemann@suse.com>
Cc: Takashi Iwai<tiwai@suse.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when interface type is MAC to Phy, netif_carrier_(on/off)
is called which is not needed as Phy lib already updates the carrier
status to net stack. This is needed only for other interface types
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) mlx4 doesn't check fully for supported valid RSS hash function, fix
from Amir Vadai
2) Off by one in ibmveth_change_mtu(), from David Gibson
3) Prevent altera chip from reporting false error interrupts in some
circumstances, from Chee Nouk Phoon
4) Get rid of that stupid endless loop trying to allocate a FIN packet
in TCP, and in the process kill deadlocks. From Eric Dumazet
5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
Eric Dumazet
6) Fix two bugs in async rhashtable resizing, from Thomas Graf
7) Fix topology server listener socket namespace bug in TIPC, from Ying
Xue
8) Add some missing HAS_DMA kconfig dependencies, from Geert
Uytterhoeven
9) bgmac driver intends to force re-polling but does so by returning
the wrong value from it's ->poll() handler. Fix from Rafał Miłecki
10) When the creater of an rhashtable configures a max size for it,
don't bark in the logs and drop insertions when that is exceeded.
Fix from Johannes Berg
11) Recover from out of order packets in ppp mppe properly, from Sylvain
Rochet
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
bnx2x: really disable TPA if 'disable_tpa' option is set
net:treewide: Fix typo in drivers/net
net/mlx4_en: Prevent setting invalid RSS hash function
mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
netfilter; Add some missing default cases to switch statements in nft_reject.
ppp: mppe: discard late packet in stateless mode
ppp: mppe: sanity error path rework
net/bonding: Make DRV macros private
net: rfs: fix crash in get_rps_cpus()
altera tse: add support for fixed-links.
pxa168: fix double deallocation of managed resources
net: fix crash in build_skb()
net: eth: altera: Resolve false errors from MSGDMA to TSE
ehea: Fix memory hook reference counting crashes
net/tg3: Release IRQs on permanent error
net: mdio-gpio: support access that may sleep
inet: fix possible panic in reqsk_queue_unlink()
rhashtable: don't attempt to grow when at max_size
bgmac: fix requests for extra polling calls from NAPI
tcp: avoid looping in tcp_send_fin()
...
bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.
Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.
The bug was an unintended consequence of commit aebf6244cd "bnx2x: Be
more forgiving toward SW GRO".
Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_check_rxfh_func() was checking for hardware support before
setting a known RSS hash function, but didn't do any check before
setting unknown RSS hash function. Need to make it fail on such values.
In this occasion, moved the actual setting of the new value from the
check function into mlx4_en_set_rxfh().
Fixes: 947cbb0 ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new gpiod_get_array and gpiod_put_array functions
(added to mainline in the v4.1 merge window) for obtaining and
disposing of GPIO descriptors.
Cc: David Miller <davem@davemloft.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PPP is used over a link which does not guarantee packet ordering,
we might get late MPPE packets. This is a problem because MPPE must be
kept synchronized and the current implementation does not drop them and
rekey 4095 times instead of 0, which is wrong.
In order to prevent rekeying about a whole count space times (~ 4095
times), drop packets which are not within the forward 4096/2 window and
increase sanity error counter.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need sanity error path a little further, rework to be
able to use the sanity error path anywhere in decompressor.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding modules currently defines four macros with
general names that pollute the global namespace:
DRV_VERSION
DRV_RELDATE
DRV_NAME
DRV_DESCRIPTION
Fixing that by defining a private bonding_priv.h
header files which includes those defines.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Add support for fixed-links in configurations without PHY.
(e.g. connection to a switch, SGMII point to point, SFPs)
Check: Documentation/devicetree/bindings/net/fixed-link.txt.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 43d3ddf87a ("net: pxa168_eth: add device tree support") starts
to use managed resources by adding devm_clk_get() and
devm_ioremap_resource(), but it leaves explicit iounmap() and clock_put()
in pxa168_eth_remove() and in failure handling code of pxa168_eth_probe().
As a result double free can happen.
The patch removes explicit resource deallocation. Also it converts
clk_disable() to clk_disable_unprepare() to make it symmetrical with
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves false errors from MSGDMA in TX mSGDMA MM to ST
mode, and is a continuation of the patch recently submitted by Andrea
Oetken. The MSGDMA had a logic bug that masked detection of this issue
prior to Quartus 14.1/Build 164. When the MSGDMA logic bug was addressed
in Quartus 14.1/Build 164, the driver problem was exposed.
The problem is corrected by making sure MSGDMA_DESC_CTL_TR_ERR_IRQ is not
set for any of the transmit DMA descriptors, and only used for receive
descriptors.
Fixes: 71cd26e altera tse: Error-Bit on tx-avalon-stream always set.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>a
Cc: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to only register the EHEA memory hotplug hooks on
adapter probe has a few problems.
Firstly the reference counting is wrong for multiple adapters, in that
the hooks are registered multiple times. Secondly the check in the tear
down path is backward. Finally the error path doesn't decrement the
count.
The multiple registration of the hooks is the biggest problem, as it
leads to oopses when the system is rebooted, and/or errors during memory
hotplug, eg:
$ ./mem-on-off-test.sh -r 2
...
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: re-initializing driver complete
ehea: memory is going offline
ehea: LPAR memory changed - re-initializing driver
ehea: opcode=26c ret=fffffffffffffffc arg1=8000000003000003 arg2=0 arg3=700000060000d600 arg4=3fded0000 arg5=200 arg6=0 arg7=0
ehea: register_rpage_mr failed
ehea: registering mr failed
ehea: register MR failed - driver inoperable!
ehea: memory is going offline
Fixes: aa18332331 ("ehea: Register memory hotplug, reboot and crash hooks on adapter probe")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When having permanent EEH error, the PCI device will be removed
from the system. For this case, we shouldn't set pcierr_recovery
to true wrongly, which blocks the driver to release the allocated
interrupts and their handlers. Eventually, we can't disable MSI
or MSIx successfully because of the MSI or MSIx interrupts still
have associated interrupt actions, which is turned into following
stack dump.
Oops: Exception in kernel mode, sig: 5 [#1]
:
[c0000000003b76a8] .free_msi_irqs+0x80/0x1a0 (unreliable)
[c00000000039f388] .pci_remove_bus_device+0x98/0x110
[c0000000000790f4] .pcibios_remove_pci_devices+0x9c/0x128
[c000000000077b98] .handle_eeh_events+0x2d8/0x4b0
[c0000000000782d0] .eeh_event_handler+0x130/0x1c0
[c000000000022bd4] .kernel_thread+0x54/0x70
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use gpio on message based busses, which
require sleeping (e.g. gpio from an I2C I/O expander).
Since this driver does not use IRQ handler, it is safe to use the
_cansleep suffixed gpio accessors.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d75b1ade56 ("net: less interrupt masking in NAPI") polling
function has to return whole budget when it wants NAPI to call it again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Fixes: eb64e2923a ("bgmac: leave interrupts disabled as long as there is work to do")
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver already uses ioremap_wc() on the same range
so when write-combining is available that will be used
instead.
Cc: Hyong-Youb Kim <hykim@myri.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: netdev@vger.kernel.org
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `grcan_free_dma_buffers':
grcan.c:(.text+0x2d7716): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `grcan_allocate_dma_buffers':
grcan.c:(.text+0x2d779c): undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `arc_emac_tx_clean':
emac_main.c:(.text+0x2decde): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `arc_emac_rx':
emac_main.c:(.text+0x2dee1c): undefined reference to `dma_unmap_single'
emac_main.c:(.text+0x2dee72): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2dee7e): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_probe':
(.text+0x2df2ee): undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `arc_emac_open':
emac_main.c:(.text+0x2df6d8): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df6e4): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_tx':
emac_main.c:(.text+0x2df9e4): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df9f0): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `xgbe_probe':
xgbe-main.c:(.text+0x2def0a): undefined reference to `dma_set_mask'
xgbe-main.c:(.text+0x2def20): undefined reference to `dma_supported'
drivers/built-in.o: In function `xgbe_rx_poll':
xgbe-drv.c:(.text+0x2e0320): undefined reference to `dma_sync_single_for_cpu'
xgbe-drv.c:(.text+0x2e035e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `xgbe_unmap_rdata':
xgbe-desc.c:(.text+0x2e5fe4): undefined reference to `dma_unmap_page'
xgbe-desc.c:(.text+0x2e5ffa): undefined reference to `dma_unmap_single'
xgbe-desc.c:(.text+0x2e604a): undefined reference to `dma_unmap_page'
xgbe-desc.c:(.text+0x2e6084): undefined reference to `dma_unmap_page'
drivers/built-in.o: In function `xgbe_alloc_pages':
xgbe-desc.c:(.text+0x2e6156): undefined reference to `dma_map_page'
xgbe-desc.c:(.text+0x2e6164): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgbe_free_ring':
xgbe-desc.c:(.text+0x2e63d4): undefined reference to `dma_unmap_page'
xgbe-desc.c:(.text+0x2e640e): undefined reference to `dma_unmap_page'
xgbe-desc.c:(.text+0x2e644a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgbe_init_ring':
xgbe-desc.c:(.text+0x2e64d4): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgbe_map_tx_skb':
xgbe-desc.c:(.text+0x2e6628): undefined reference to `dma_map_single'
xgbe-desc.c:(.text+0x2e6638): undefined reference to `dma_mapping_error'
xgbe-desc.c:(.text+0x2e66b2): undefined reference to `dma_map_single'
xgbe-desc.c:(.text+0x2e66c2): undefined reference to `dma_mapping_error'
xgbe-desc.c:(.text+0x2e6762): undefined reference to `dma_map_page'
xgbe-desc.c:(.text+0x2e6772): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the PAPR document which defines the virtual device interface used by
the ibmveth driver doesn't specify a specific maximum MTU. So, in the
ibmveth driver, the maximum allowed MTU is determined by the maximum
allocated buffer size of 64k (corresponding to one page in the common case)
minus the per-buffer overhead IBMVETH_BUFF_OH (which has value 22 for 14
bytes of ethernet header, plus 8 bytes for an opaque handle).
This suggests a maximum allowable MTU of 65514 bytes, but in fact the
driver only permits a maximum MTU of 65513. This is because there is a <
instead of an <= in ibmveth_change_mtu(), which only permits an MTU which
is strictly smaller than the buffer size, rather than allowing the buffer
to be completely filled.
This patch fixes the buglet.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of vxlan_fdb_replace always is greater than or equal to 0
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 02c958dd3 (net/macb: add TX multiqueue support for gem), the
initialization of tx_head and tx_tail in macb_init_rings() was moved
inside the loop that iterates over each element in the ring. Since
tx_head and tx_tail only need to be assigned once, move them back out of
the loop.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.
Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.
This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Pull networking fixes from David Miller:
"Just a few fixes trickling in at this point.
1) If we see an attached socket on an skb in the ipv4 forwarding path,
bail. This can happen due to races with FIB rule addition, and
deletion, and we should just drop such frames. From Sebastian
Pöhn.
2) pppoe receive should only accept packets destined for this hosts's
MAC address. From Joakim Tjernlund.
3) Handle checksum unwrapping properly in ppp receive properly when
it's encapsulated in UDP in some way, fix from Tom Herbert.
4) Fix some bugs in mv88e6xxx DSA driver resulting from the conversion
from register offset constants to mnenomic macros. From Vivien
Didelot.
5) Fix handling of HCA max message size in mlx4 adapters, from Eran
Ben ELisha"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/mlx4_core: Fix reading HCA max message size in mlx4_QUERY_DEV_CAP
tcp: add memory barriers to write space paths
altera tse: Error-Bit on tx-avalon-stream always set.
net: dsa: mv88e6xxx: use PORT_DEFAULT_VLAN
net: dsa: mv88e6xxx: fix setup of port control 1
ppp: call skb_checksum_complete_unset in ppp_receive_frame
net: add skb_checksum_complete_unset
pppoe: Lacks DST MAC address check
ip_forward: Drop frames with attached skb->sk
Currently we parse max_msg_sz from the wrong offset in QUERY_DEV_CAP,
fix to use the right offset.
Fixes: 0b131561a7 ('net/mlx4_en: Add Flow control statistics [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).
This only applies to the tse-configuration with MSGDMA.
This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).
According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b13375 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
In the case of a DMA mapping error on the last iteration of
the loop of the allocation of memory of the FW monitor we
indeed free the pages, but don't NULL out the page variable
thus allowing for the possibility of setting the FW monitor
variables with invalid data to use.
Fixes: c2d202017d ("iwlwifi: pcie: add firmware monitor capabilities")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If for some reason statistics notification received from the firmware
reports 0 in average beacon RSSI value, then skip it and avoid signal
based decisions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan iteration complete notification handling uses the wrong FW API
version (version 2 instead of version 3).
Fix that by removing version 2 API which is no longer used, and using
only the updated version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the delay paramatere is provided, we need to stop
the collection only after the delay has elapsed.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't relate the scan to a vif. The scan is
run by a separate entity called auxiliary MAC (aka AUX MAC).
This AUX MAC needs to get Tx power limitations that are
not applied on a specific vif, but on the device as a whole.
This can be implemented by using the minimum of all the
values set by the user for all the MACs. But then we need
to ignore the limitations that come from the AP or
regulatory for a specific vif: a specific vif might have
regulatory limitations because of the channel is works on.
This limit is irrelevant for the AUX MAC.
Use the new API from mac80211: the user_power_level in
bss_conf to achieve this.
Firmware -13.ucode has already moved to this API.
Change-Id: Ifba83660f378e91b93bd46d29fe8ba35a7c168a4
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull networking fixes from David Miller:
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'. Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.
Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 04ffcb255f ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().
Then later, when generalizing this in commit 5f35227ea3
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.
Remove the unused argument and go back to the code as before.
Cc: Tom Herbert <therbert@google.com>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you redirect a VLAN device to any device, you end up with
crap in af_packet on the xmit path because hard_header_len is
not equal to skb->mac_len. So the redirected packet contains
four extra bytes at the start which then gets interpreted as
part of the MAC address.
This patch fixes this by only pushing skb->mac_len. We also
need to fix ifb because it tries to undo the pushing done by
act_mirred.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/mv88e6xxx.c: In function ‘mv88e6xxx_set_port_state’:
drivers/net/dsa/mv88e6xxx.c:905: warning: ‘ret’ may be used uninitialized in this function
If oldstate == state, mv88e6xxx_set_port_state() will return an
uninitialized value. Pre-initialize ret to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use a single source list of hypercalls, generating other tables
etc. at build time.
- Add a "Xen PV" APIC driver to support >255 VCPUs in PV guests.
- Significant performance improve to guest save/restore/migration.
- scsiback/front save/restore support.
- Infrastructure for multi-page xenbus rings.
- Misc fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVL6OZAAoJEFxbo/MsZsTRs3YH/2AycBHs129DNnc2OLmOklBz
AdD43k+FOfZlv0YU80WmPVmOpGGHGB5Pqkix2KtnvPYmtx3pb/5ikhDwSTWZpqBl
Qq6/RgsRjYZ8VMKqrMTkJMrJWHQYbg8lgsP5810nsFBn/Qdbxms+WBqpMkFVo3b2
rvUZj8QijMJPS3qr55DklVaOlXV4+sTAytTdCiubVnaB/agM2jjRflp/lnJrhtTg
yc4NTrIlD1RsMV/lNh92upBP/pCm6Bs0zQ2H1v3hkdhBBmaO0IVXpSheYhfDOHfo
9v209n137N7X86CGWImFk6m2b+EfiFnLFir07zKSA+iZwkYKn75znSdPfj0KCc0=
=bxTm
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- use a single source list of hypercalls, generating other tables etc.
at build time.
- add a "Xen PV" APIC driver to support >255 VCPUs in PV guests.
- significant performance improve to guest save/restore/migration.
- scsiback/front save/restore support.
- infrastructure for multi-page xenbus rings.
- misc fixes.
* tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Try harder to get PXM information for Xen
xenbus_client: Extend interface to support multi-page ring
xen-pciback: also support disabling of bus-mastering and memory-write-invalidate
xen: support suspend/resume in pvscsi frontend
xen: scsiback: add LUN of restored domain
xen-scsiback: define a pr_fmt macro with xen-pvscsi
xen/mce: fix up xen_late_init_mcelog() error handling
xen/privcmd: improve performance of MMAPBATCH_V2
xen: unify foreign GFN map/unmap for auto-xlated physmap guests
x86/xen/apic: WARN with details.
x86/xen: Provide a "Xen PV" APIC driver to support >255 VCPUs
xen/pciback: Don't print scary messages when unsupported by hypervisor.
xen: use generated hypercall symbols in arch/x86/xen/xen-head.S
xen: use generated hypervisor symbols in arch/x86/xen/trace.c
xen: synchronize include/xen/interface/xen.h with xen
xen: build infrastructure for generating hypercall depending symbols
xen: balloon: Use static attribute groups for sysfs entries
xen: pcpu: Use static attribute groups for sysfs entry
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Configure flow control correctly, and based on the receive fifo size read
as a property from the devicetree since the Synopsys stmmac fifo sizes are
configurable based on a particular chip's implementation. This patch maintains
the previous incorrect behavior unless the receive fifo size is found in the
devicetree.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unicast pause frame detect was not being enabled for the Synopsys stmmac. This
patch sets Unicast pause frame detect in MAC register 6 so that pause frame
detection by the stmmac conforms to IEEE 802.3, Annex 31B.3.3 Receive
Operation - Specifically, a MAC shall respond to pause frames containing
either the reserved multicast address or the unique physical address
associated with this station.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the tx-fifo-depth and rx-fifo-depth from the devicetree. The Synopsys
stmmac controller fifos are configurable per product instance, and the fifo
sizes are needed to configure certain features correctly such as flow control.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add defines and documentation for enabling flow control on the stmmac. Flow
control was not implemented correctly on the stmmac driver and is currently
non-functional as a result. This is the first in a series of small patches
to correctly implement this feature.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An oops exists in the flow of stmmac_release().
phy_ethtool_get_wol() depends on phydev->drv.
phydev->drv will be null after stmmac_mdio_unreg() completes.
Steps to reproduce on Quark X1000:
1. ifconfig eth0 192.168.0.1
2. rmmod stmmac_pci
To fix this stmmac_mdio_unreg() should be run after unregister_netdev().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reported-by: Dan O'Donovan <dan.odonovan@emutex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A duplicate declaration of 'ret' can result in hiding an error code.
Drop it.
Fixes: 17ee3e04dd ("net: dsa: Provide additional RMON statistics")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -EINVAL from the invalid PCI region size error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
set_filter_wr is requesting __GFP_NOFAIL allocation although it can return
ENOMEM without any problems obviously (t4_l2t_set_switching does that
already). So the non-failing requirement is too strong without any
obvious reason. Drop __GFP_NOFAIL and reorganize the code to have the
failure paths easier.
The same applies to _c4iw_write_mem_dma_aligned which uses __GFP_NOFAIL
and then checks the return value and returns -ENOMEM on failure. This
doesn't make any sense what so ever. Either the allocation cannot fail or
it can.
del_filter_wr seems to be safe as well because the filter entry is not
marked as pending and the return value is propagated up the stack up to
c4iw_destroy_listen.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-14
This series contains updates to i40e and i40evf.
Mitch provides a fix for i40e, where VFs were gone and the associated
VSI's had been removed and the rings were not stopped, which in some
circumstances cased memory corruption or DMAR errors. So stop all the
rings associated with each VF before releasing its resources. Also
cleaned up a poorly indented piece of code. Fixes VF link state, where
VF devices were assuming link is up unless told otherwise, which means
that VFs instantiated on a PF with no link, would report the wrong state.
Anjali adds support to add Flow director Sideband rules for a VF from it's
PF. Fixes a recently discovered hardware issue, where after a VFLR
hardware might be indicating to us a reset completion little too early, so
wait another 10 msec for cache to be cleaned up.
Jesse enables the user to dump the internal hardware state for better
debugging by allowing a bash script to acquire information about the
internal hardware state. The data output to the kernel log is collected
by the script and can then be sent to Intel. Also fixed a possible
failure path to allocate memory that was found by smatch. Cleaned up
unused local variables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9a2620c877 ("bnx2x: prevent WARN during driver unload")
switched the napi/busy_lock locking mechanism from spin_lock() into
spin_lock_bh(), breaking inter-operability with netconsole, as netpoll
disables interrupts prior to calling our napi mechanism.
This switches the driver into using atomic assignments instead of the
spinlock mechanisms previously employed.
Based on initial patch from Yuval Mintz & Ariel Elior
I basically added softirq starvation avoidance, and mixture
of atomic operations, plain writes and barriers.
Note this slightly reduces the overhead for this driver when no
busy_poll sockets are in use.
Fixes: 9a2620c877 ("bnx2x: prevent WARN during driver unload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code sets the expiry value of the timer to a relative value and
starts it with hrtimer_start_expires. That's fine, but that only works
once. The timer is started in relative mode, so the expiry value gets
overwritten with the absolut expiry time (now + expiry).
So once the timer expired, a new call to hrtimer_start_expires results
in an immidiately expired timer, because the expiry value is
already in the past.
Use the proper mechanisms to (re)start the timer in the intended way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: dingtianhong <dingtianhong@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: netdev@vger.kernel.org
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
If CONFIG_ARCH_DMA_ADDR_T_64BIT enabled for x86 systems and physical
memory is more than 4GB, dma_map_page may return a valid memory
address which greater than 0xffffffff. As a result, the mlx5 device page
allocator RB tree will be initialized with valid addresses greater than
0xfffffff.
However, (addr & PAGE_MASK) set the high four bytes to zeros. So, it's
impossible for the function, free_4k, to release the pages whose
addresses greater than 4GB. Memory leaks. And mlx5_ib module can't
release the pages when user try to remove the module, as a result,
system hang.
[root@rdma05 root]# dmesg | grep addr | head
addr = 3fe384000
addr & PAGE_MASK = fe384000
[root@rdma05 root]# rmmod mlx5_ib <---- hang on
---------------------- cosnole log -----------------
mlx5_ib 0000:04:00.0: irq 138 for MSI/MSI-X
alloc irq_desc for 139 on node -1
alloc kstat_irqs on node -1
mlx5_ib 0000:04:00.0: irq 139 for MSI/MSI-X
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
---------------------- cosnole log -----------------
Fixes: bf0bf77f65 ('mlx5: Support communicating arbitrary host page size to firmware')
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return the admin alias GUID value upon a GET request via HOST. We do this so
that the GUID value requested by the admin is returned even if the SM has not
yet approved this GUID (e.g. the SM is down).
Note that this does not create a problem, since the virtual port will remain
down until the SM does ACK the requested GUID value.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There might be cases that PF doesn't get a "reset" command upon slave down
(e.g. virsh destroy). In these cases, however, an FLR event is issued.
Therefore, when the PF receives an FLR event for a slave, it should also
generate a shutdown event on the PF for that slave, to let the PF upper
layers (mlx4_ib, eth) perform any required cleanup/actions associated
with slave shutdown.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To have out of the box experience, the PF generates random GUIDs who
serve as the initial admin values.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Manages alias GUIDs per VF per port in the core layer.
This is a pre-step for managing alias GUIDs in a mode that the admin
GUID is returned via ib_query_gid() regardless of whether the SM
has approved it or not.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix up some ->d_inode accesses in the chelsio driver.
(1) FILE_DATA() should just be replaced with file_inode().
(2) set_debugfs_file_size() should be removed and debugfs_create_file_size()
should be used to create the file.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Originally Xen PV drivers only use single-page ring to pass along
information. This might limit the throughput between frontend and
backend.
The patch extends Xenbus driver to support multi-page ring, which in
general should improve throughput if ring is the bottleneck. Changes to
various frontend / backend to adapt to the new interface are also
included.
Affected Xen drivers:
* blkfront/back
* netfront/back
* pcifront/back
* scsifront/back
* vtpmfront
The interface is documented, as before, in xenbus_client.c.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Bump.
Change-ID: Id14baae72332d0f1a9bc5d351ea1a85cb0295ec3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel has added SPEED_40000 for ethtool.
Go ahead and use the new #define.
Change-ID: Ic7e16e5c9e91085afe539f11ee1b7668adc4d0ef
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes just remove unused variables and any code that uses them
as the results of storing into these variables doesn't have any
side effects that I can see or provide any benefit.
Change-ID: I8a5ec7132ff1443d23aae729cef94beaaaf19e3a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_interrupt_scheme function had a possible failure
path to allocate memory that was found by smatch.
This adds the correct handling to the function to abort
probe if the memory allocation fails.
Change-ID: I2bf1d826a244209619da4c452d0d58b3eb5e26a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the 8 bytes of the WR_CSR_PROT field returned as part of the get
device/function capabilities AQ command.
Change-ID: Ifcaeea2ff29885fa769e4f384c7db88a25e8afd0
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJVLbO+AAoJEILEb/54YlRx5N4QAJXsmEW1FL2l6mMAyTQkEsVj
nbqjF9I6aJgYM9+i8GKaZJxpN17SAZ7Ii7aCAXjPwX8AvjT70+gcZr+KDWtPir61
B75VNVEcUYOR4vOF5Z6rQcQMlhGPkfMOJYXFMahpOG6DdPbVh1x2/tuawfc6IC0V
a6S/fln6WqHrXQ+8swDSv1KuZsav6+8AQaTlNUQkkuXdY9b3k/3xiy5C2K26APP8
x1B39iAF810qX6ipnK0gEOC3Vs29dl7hvNmgOVmmkBGVS7+pqTuy5n1/9M12cDRz
78IQ7DXB0NcSwr5tdrmGVUyH0Q6H9lnD3vO7MJkYwKDh5a/2MiBr2GZc4KHDKDWn
E1sS27f1Pdn9qnpWLzTcY+yYNV3EEyre56L2fc+sh+Xq9sNOjUah+Y/eAej/IxYD
XYRf+GAj768yCJgNP+Y3PJES/PRh+0IZ/dn5k0Qq2iYvc8mcObyG6zdQIvCucv/i
70uV1Z2GWEb31cI9TUV8o5GrMW3D0KI9EsCEEpiFFUnhjNog3AWcerGgFQMHxu7X
ZnNSzudvek+XJ3NtpbPgTiJAmnMz8bDvBQm3G1LUO2TQdjYTU6YMUHsfzXs8DL6c
aIMWO4stkVuDtWrlT/hfzIXepliccyXmSP6sbH+zNNCepulXe5C4M2SftaDi4l/B
uIctXWznvHoGys+EFL+v
=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
This is a feature to enable better debugging of user reported issues by
allowing a bash script to acquire information about the internal hardware
state. The data output to the kernel log is collected by the script and can
then be sent to Intel. This is a critical debugging feature for helping us
interpret and reproduce complex customer setups.
Change-ID: Ie8b3ab09086d6870a709015f51ada05af10b41bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is to allow quick check for FCoE capability is enabled or not
in device function before any SW overrides.
Change-ID: I5f78ba798d566f143161273156916c6f4074496e
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a HW issue that was recently discovered, after a VFLR HW might be
indicating to us a reset completion little too early. So wait another 10
msec for cache to be cleaned up.
Change-ID: I6a24dcf5dd7ffcd6500246e717411ef58532d1e9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the VF notification functions to the top of the file. This
eliminates an unnecessary declaration.
Change-ID: I036171f14180ee9f0ce4e0a21334d6a217d06c94
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Gratuitously notify VFs of link state when they activate their queues.
In general, this is the last thing that a VF driver will do as it opens
its interface, so this is a good time to notify the VF.
Currently, VF devices assume link is up unless told otherwise, which
means that VFs instantiated on a PF with no link will report the wrong
state. This change corrects that issue.
Change-ID: Iea53622904ecc681ac3f8938d81c30033ef9a0a6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The aq_pending field in the adapter structure is actually redundant with
the current_op field. Remove the aq_pending field and expunge all traces
of it from the official record. This simplifies the code significantly,
especially in the virtual channel completion routine.
Change-ID: Ib2957c8c19882bd0cecc6fcd133912c24b46a1ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we can now add Flow director Sideband rules for a VF from
it's PF. Here is an example on how it can be done when VF id = 5 and
queue = 2:
"ethtool -N ethx flow-type udp4 src-ip x.x.x.x dst-ip y.y.y.y src-port p1 dst-port p2 action 2 user-def 5"
User-def specifies VF id and action specifies queue.
Change-ID: Ib37d6dff3823a4d85caffde638473891c38c2b89
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not sure how this slipped through. Cosmetic change only.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed,
the rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing
memory corruption or DMAR errors, both of which would lead to general
malaise of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the recent driver changes, bump the version.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
VFs were being improperly added to the switch's multicast group. The
error stems from the fact that incorrect arguments were passed to the
"update_mc_addr" function. It would seem to be a copy paste error since
the parameters are similar to the "update_uc_addr" function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we call update_max_size it does not drop all oversized messages.
This is due to the difficulty in performing this operation, since it is
a FIFO which makes updating anything other than head or tail very
difficult. To fix this, modify validate_msg_size to ensure that we error
out later when trying to transmit the message that could be oversized.
This will generally be a rare condition, as it requires the FIFO to
include a message larger than the max_size negotiated during mailbox
connect. Note that max_size is always smaller than rx.size so it should
be safe to use here.
Also, update the update_max_size function header comment to clearly
indicate that it does not drop all oversized messages, but only those at
the head of the FIFO.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we forcefully shutdown the mailbox, we then go about resetting max
size to 0, and clearing all messages in the FIFO. Instead, we should
just reset the head pointer so that the FIFO becomes empty, rather than
changing the max size to 0. This helps prevent increment in tx_dropped
counter during mailbox negotiation, which is confusing to viewers of
Linux ethtool statistics output.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of dropped doesn't really mean dropped mailbox messages, but
rather specifically messages which were too large to fit in the remote
Rx FIFO. Rename the stat to more clearly indicate what it means.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the PF receives a request to update a multicast address for the VF,
it checks the enabled multicast mode first. Fix a bug where the VF tried
to set a multicast address before requesting the required xcast mode.
This ensures the multicast addresses are honored as long as the xcast
mode was allowed.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the service task handles varying work that doesn't all require the
interface to be up, launch the service timer immediately. This ensures
that we continually check the mailbox, as well as handle other tasks
while the device is down.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The header comment included a miscopy of a C-code line, and also
mis-used Rx FIFO when it clearly meant Tx FIFO
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a header comment explaining why we have the somewhat crazy mailbox
flow. This flow is necessary as it prevents the PF<->SM mailbox from
being flooded by the VF messages, which normally trigger a message to
the PF. This helps prevent the case where we see a PF mailbox timeout.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we already schedule the service task, we can just wait for this
task to handle the mailbox events from the VF. This reduces some complex
code flow, and makes it so we have a single path for handling the VF
messages. There is a possibility that we have a slight delay in handling
VF messages, but it should be minimal.
The result of tx_complete and !rx_ready is insufficient to determine
whether we need to process the mailbox. There is a possible race
condition whereby the VF fills up the mbmem for us, but we have already
recently processed the mailboxes in the interrupt. During this time,
the interrupt is disabled. Thus, our Rx FIFO is empty, but the mbmem now
has data in it. Since we continually check whether Rx FIFO is empty, we
then never call process. This results in the possibility to prevent PF
from handling the VF mailbox messages.
Instead, just call process every time, despite the fact that we may or
may not have anything to process for the VF. There should be minimal
overhead for doing this, and it resolves an issue where the VF never
comes up due to never getting response for its SET_LPORT_STATE message.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we run the watchdog periodically, which might take a while and
potentially monopolize the system default workqueue, create our own
separate work queue. This also helps reduce and stabilize latency
between scheduling the work in our interrupt and actually performing
the work. Still use a timer for the regular scheduled interval but
queue the work onto its own work queue.
It seemed overkill to create a single workqueue per interface, so we
just spawn a single work queue for all interfaces upon driver load. For
this reason, use a multi-threaded workqueue with one thread per
processor, rather than single threaded queue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When returning virtualization queues from the VF back to the PF, do not
retain the VF rate limiter.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Todd Russell <todd.a.russell@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Named it tx_hang_count to differentiate it from tx_hwtstamp_timeout.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incrementing the tx_timeout_count for both the Tx hang
and then for all reset flows. Instead, we should only increment
tx_timeout_count in the Tx hang path, so that our Tx hang counter
does not increment when it was not caused by a Tx hang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we already print this message when a reset is requested via the
RESET_REQUESTED flag, we do not need to print it before setting the
flag.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue with ethtool stats displaying useless
values on the VF, because some stats simply have no meaning to the VF.
Resolve this by splitting these out into PF_STATS and only showing them
if we aren't the VF.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though it shouldn't strictly matter, don't count queue stats higher
than the max_queues value stored for this mac. This ensures that we
don't attempt to check queues which don't belong to use in VFs. This
shouldn't be a visible change, as the VFs should see zero for queues
which don't belong to them.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we show statistics for all 128 queues, even though we don't
necessarily have that many queues available especially in the VF case.
Instead, use the hw->mac.max_queues value, which tells us how many
queues we actually have, rather than the space for the rings we
allocated. In this way, we prevent dumping statistics that are useless
on the VF.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the user was not allowed to create a VLAN interface on top
of the switch default vid.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The were several functions which had parameters which were never or
sometimes used in functions. To resolve possible compiler warnings,
use __always_unused or __maybe_unused kernel macros to resolve.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a function called "fm10k_netpoll" that's used to define
"ndo_poll_controller" in "fm10k_netdev_ops". This is required to enable
support for "netconsole" in fm10k.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the VFs do not read the default VLAN during initialization,
so they will not be able to indicate untagged frames properly.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Corrected a spelling mistake that was found over time.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Output of ethtool was reporting 2 rx_errors entries. This change
removes one of the redundant entries.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
The function collecting Tx statistics was actually using values from the RX
ring. Thus, Tx and Rx statistics values reported by "ifconfig" will
return identical values. This change corrects this error and the Tx
statistics is now reading from the Tx ring.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comment for tx filt and sge length calucaltion code, also remove
a hardcoded value
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fl_starv_thres could be different from adapter to adapter, don't use
hardcoded values
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a significant latency drop for packets of sizes between 128 and 192
bytes
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring size is always known at compile time, so make the code a bit
more efficient
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to inform the hardware about the first invalid (not yet
filled) rx slot, by writing its DMA descriptor pointer offset to the
BGMAC_DMA_RX_INDEX register.
This register was set to a value exceeding the rx ring size, effectively
allowing the hardware constant access to the full ring, regardless of
which slots are initialized.
To fix this issue, always mark the last filled rx slot as invalid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating buffers at device init time and initializing
descriptors at device open, do both at the same time (during open).
Free all buffers when closing the device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting it to 511 looks like a failed attempt at leaving one descriptor
empty to allow the hardware to stop processing a buffer that has not
been prepared yet. However, this doesn't work because this affects the
total ring size as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In very rare cases, the MAC can catch an internal buffer that is bigger
than it's supposed to be. Instead of crashing the kernel, simply pass
the buffer back to the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a new buffer before processing the completed one. If allocation
fails, reuse the old buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet buffer offset of 30 bytes is inefficient, because the first 2
bytes end up in a different cacheline.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always poll rx and tx during NAPI poll instead of relying on the status
of the first interrupt. This prevents bgmac_poll from leaving unfinished
work around until the next IRQ.
In my tests this makes bridging/routing throughput under heavy load more
stable and ensures that no new IRQs arrive as long as bgmac_poll uses up
the entire budget.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep incrementing ring->start and ring->end instead of pointing it to
the actual ring slot entry. This simplifies the calculation of the
number of free slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If remaining space in a send buffer slot is too small for the whole message,
we only copy the RNDIS header and PPI data into send buffer, so we can batch
one more packet each time. It reduces the vmbus per-message overhead.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that
user space tools like perf and trace-cmd can parse the binary data
and express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values
by the C pre-processor. Thus, the enum string is exported to the
format file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings
in the TP_printk() format into their number, and that is what is
shown to user space. For example, the tracepoint tlb_flush currently
has this in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVLBTuAAoJEEjnJuOKh9ldjHMIALdRS755TXCZGOf0r7O2akOR
wMPeum7C+ae1mH+jCsJKUC0/jUfQKaMt/UxoHlipDgcGg8kD2jtGnGCw4Xlwvdsr
y4rFmcTRSl1mo0zDSsg6ujoupHlVYN0+JPjrd7S3cv/llJoY49zcanNLF7S2XLeM
dZCtWRLWYpBiWO68ai6AqJTnE/eGFIqBI048qb5Eg8dbK243SSeSIf9Ywhb+VsA+
aq6F7cWI/H6j4tbeza8tAN19dcwenDro5EfCDY8ARQHJu1f6Y3+DLf2imjkd6Aiu
JVAoGIjHIpI+djwCZC1u4gi4urjfOqYartrM3Q54tb3YWYqHeNqP2ASI2a4EpYk=
=Ixwt
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
e1000e is the only driver requiring pm_qos_req, instead of causing
every device to waste up to 240 bytes. Allocate it for the specific
driver.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-11
This series contains updates to iflink, ixgbe and ixgbevf.
The entire set of changes come from Vlad Zolotarov to ultimately add
the ethtool ops to VF driver to allow querying the RSS indirection table
and RSS random key.
Currently we support only 82599 and x540 devices. On those devices, VFs
share the RSS redirection table and hash key with a PF. Letting the VF
query this information may introduce some security risks, therefore this
feature will be disabled by default.
The new netdev op allows a system administrator to change the default
behaviour with "ip link set" command. The relevant iproute2 patch has
already been sent and awaits for this series upstream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics are grouped by TX and RX errors.
The SQE Test Errors Register indicates problems with TX.
Signed-off-by: Wolfgang Steinwender <wsteinwender@pcs.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
All places outside of core VFS that checked ->read and ->write for being NULL or
called the methods directly are gone now, so NULL {read,write} with non-NULL
{read,write}_iter will do the right thing in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.
This enables the ethtool's "-x" and "--show-rxfh[-indir]" options for VF
devices.
This patch adds the support for 82599 and x540 devices only. Support for
other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ixgbevf_get_rss_key() function that queries the PF for an RSS
Random Key using a new VF-PF channel IXGBE_VF_GET_RSS_KEY command.
This patch adds the support for 82599 and x540 devices only. Support for
other devices will be added later.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Benjamin Poirier
Nicolas Dichtel
Antonio Ospite
Michal Schmidt
Simon Xiao
Johannes Berg
Emmanuel Grumbach
Eran Harary
Larry Finger
Karicheri, Muralidharan
Linus Torvalds
Masanari Iida
Amir Vadai
Rojhalat Ibrahim
Sylvain Rochet
Matan Barak
Andreas Oetken
Alexey Khoroshilov
Chee Nouk Phoon
Michael Ellerman
Gavin Shan
Vivien Didelot
Rafał Miłecki
Luis R. Rodriguez
Geert Uytterhoeven
David Gibson
Li RongQing
Ben Shelton
Yuval Mintz
Eran Ben Elisha
Tom Herbert
Joakim Tjernlund
Liad Kaufman
Alexander Bondar
Avraham Stern
Avri Altman
David S. Miller
Andreas Oetken
Herbert Xu
Vince Bridgers
Bryan O'Donoghue
Guenter Roeck
Wei Yongjun
Michal Hocko
Eric Dumazet
Thomas Gleixner
Doug Ledford
Honggang LI
Yishai Hadas
David Howells
Wei Liu
Catherine Sullivan
Greg Rose
Jesse Brandeburg
Kevin Scott
Vasu Dev
Anjali Singhai Jain
Mitch Williams
Jeff Kirsher
Hariprasad Shenai
Felix Fietkau
Daniel Axtens
Haiyang Zhang
Thomas Graf
Wolfgang Steinwender
Rafael J. Wysocki
Al Viro
Vlad Zolotarov