We have identified a problem with the "oversubscription" policy in the
link transmission code.
When small messages are transmitted, and the sending link has reached
the transmit window limit, those messages will be bundled and put into
the link backlog queue. However, bundles of data messages are counted
at the 'CRITICAL' level, so that the counter for that level, instead of
the counter for the real, bundled message's level is the one being
increased.
Subsequent, to-be-bundled data messages at non-CRITICAL levels continue
to be tested against the unchanged counter for their own level, while
contributing to an unrestrained increase at the CRITICAL backlog level.
This leaves a gap in congestion control algorithm for small messages
that can result in starvation for other users or a "real" CRITICAL
user. Even that eventually can lead to buffer exhaustion & link reset.
We fix this by keeping a 'target_bskb' buffer pointer at each levels,
then when bundling, we only bundle messages at the same importance
level only. This way, we know exactly how many slots a certain level
have occupied in the queue, so can manage level congestion accurately.
By bundling messages at the same level, we even have more benefits. Let
consider this:
- One socket sends 64-byte messages at the 'CRITICAL' level;
- Another sends 4096-byte messages at the 'LOW' level;
When a 64-byte message comes and is bundled the first time, we put the
overhead of message bundle to it (+ 40-byte header, data copy, etc.)
for later use, but the next message can be a 4096-byte one that cannot
be bundled to the previous one. This means the last bundle carries only
one payload message which is totally inefficient, as for the receiver
also! Later on, another 64-byte message comes, now we make a new bundle
and the same story repeats...
With the new bundling algorithm, this will not happen, the 64-byte
messages will be bundled together even when the 4096-byte message(s)
comes in between. However, if the 4096-byte messages are sent at the
same level i.e. 'CRITICAL', the bundling algorithm will again cause the
same overhead.
Also, the same will happen even with only one socket sending small
messages at a rate close to the link transmit's one, so that, when one
message is bundled, it's transmitted shortly. Then, another message
comes, a new bundle is created and so on...
We will solve this issue radically by another patch.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe932 ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit eliminates the use of the link 'stale_limit' & 'prev_from'
(besides the already removed - 'stale_cnt') variables in the detection
of repeated retransmit failures as there is no proper way to initialize
them to avoid a false detection, i.e. it is not really a retransmission
failure but due to a garbage values in the variables.
Instead, a jiffies variable will be added to individual skbs (like the
way we restrict the skb retransmissions) in order to mark the first skb
retransmit time. Later on, at the next retransmissions, the timestamp
will be checked to see if the skb in the link transmq is "too stale",
that is, the link tolerance time has passed, so that a link reset will
be ordered. Note, just checking on the first skb in the queue is fine
enough since it must be the oldest one.
A counter is also added to keep track the actual skb retransmissions'
number for later checking when the failure happens.
The downside of this approach is that the skb->cb[] buffer is about to
be exhausted, however it is always able to allocate another memory area
and keep a reference to it when needed.
Fixes: 77cf8edbc0 ("tipc: simplify stale link failure criteria")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.
We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface. The clones are dropped at reception
and have no functional role except making the traffic visible.
The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.
v3 - Function dev_nit_active used to check for network taps.
- Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 365ad353c2 ("tipc: reduce risk of user starvation during
link congestion") we allowed senders to add exactly one list of extra
buffers to the link backlog queues during link congestion (aka
"oversubscription"). However, the criteria for when to stop adding
wakeup messages to the input queue when the overload abates is
inaccurate, and may cause starvation problems during very high load.
Currently, we stop adding wakeup messages after 10 total failed attempts
where we find that there is no space left in the backlog queue for a
certain importance level. The counter for this is accumulated across all
levels, which may lead the algorithm to leave the loop prematurely,
although there may still be plenty of space available at some levels.
The result is sometimes that messages near the wakeup queue tail are not
added to the input queue as they should be.
We now introduce a more exact algorithm, where we keep adding wakeup
messages to a level as long as the backlog queue has free slots for
the corresponding level, and stop at the moment there are no more such
slots or when there are no more wakeup messages to dequeue.
Fixes: 365ad35 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
% grep 'tx none' include/uapi/linux/tipc_config.h
#define TIPC_CMD_NOOP 0x0000 /* tx none, rx none */
#define TIPC_CMD_GET_MEDIA_NAMES 0x0002 /* tx none, rx media_name(s) */
#define TIPC_CMD_GET_BEARER_NAMES 0x0003 /* tx none, rx bearer_name(s) */
#define TIPC_CMD_SHOW_PORTS 0x0006 /* tx none, rx ultra_string */
#define TIPC_CMD_GET_REMOTE_MNG 0x4003 /* tx none, rx unsigned */
#define TIPC_CMD_GET_MAX_PORTS 0x4004 /* tx none, rx unsigned */
#define TIPC_CMD_GET_NETID 0x400B /* tx none, rx unsigned */
#define TIPC_CMD_NOT_NET_ADMIN 0xC001 /* tx none, rx none */
This patch relaxes the original fix and rejects messages without
arguments only if such arguments are expected by a command (reg_type is
non zero).
Fixes: 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
Cc: stable@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In conjunction with changing the interfaces' MTU (e.g. especially in
the case of a bonding) where the TIPC links are brought up and down
in a short time, a couple of issues were detected with the current link
changeover mechanism:
1) When one link is up but immediately forced down again, the failover
procedure will be carried out in order to failover all the messages in
the link's transmq queue onto the other working link. The link and node
state is also set to FAILINGOVER as part of the process. The message
will be transmited in form of a FAILOVER_MSG, so its size is plus of 40
bytes (= the message header size). There is no problem if the original
message size is not larger than the link's MTU - 40, and indeed this is
the max size of a normal payload messages. However, in the situation
above, because the link has just been up, the messages in the link's
transmq are almost SYNCH_MSGs which had been generated by the link
synching procedure, then their size might reach the max value already!
When the FAILOVER_MSG is built on the top of such a SYNCH_MSG, its size
will exceed the link's MTU. As a result, the messages are dropped
silently and the failover procedure will never end up, the link will
not be able to exit the FAILINGOVER state, so cannot be re-established.
2) The same scenario above can happen more easily in case the MTU of
the links is set differently or when changing. In that case, as long as
a large message in the failure link's transmq queue was built and
fragmented with its link's MTU > the other link's one, the issue will
happen (there is no need of a link synching in advance).
3) The link synching procedure also faces with the same issue but since
the link synching is only started upon receipt of a SYNCH_MSG, dropping
the message will not result in a state deadlock, but it is not expected
as design.
The 1) & 3) issues are resolved by the last commit that only a dummy
SYNCH_MSG (i.e. without data) is generated at the link synching, so the
size of a FAILOVER_MSG if any then will never exceed the link's MTU.
For the 2) issue, the only solution is trying to fragment the messages
in the failure link's transmq queue according to the working link's MTU
so they can be failovered then. A new function is made to accomplish
this, it will still be a TUNNEL PROTOCOL/FAILOVER MSG but if the
original message size is too large, it will be fragmented & reassembled
at the receiving side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit along with the next one are to resolve the issues with the
link changeover mechanism. See that commit for details.
Basically, for the link synching, from now on, we will send only one
single ("dummy") SYNCH message to peer. The SYNCH message does not
contain any data, just a header conveying the synch point to the peer.
A new node capability flag ("TIPC_TUNNEL_ENHANCED") is introduced for
backward compatible!
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/tipc_toprsv_listener_data_ready/tipc_topsrv_listener_data_ready/
(r and s switched in topsrv)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tipc_msg_validate() function leaves a boolean flag 'validated' in
the validated buffer's control block, to avoid performing this action
more than once. However, at reception of new packets, the position of
this field may already have been set by lower layer protocols, so
that the packet is erroneously perceived as already validated by TIPC.
We fix this by initializing the said field to 'false' before performing
the initial validation.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_named_node_up() creates a skb list. It passes the list to
tipc_node_xmit() which has some code paths that can call
skb_queue_purge() which relies on the list->lock being initialised.
The spin_lock is only needed if the messages end up on the receive path
but when the list is created in tipc_named_node_up() we don't
necessarily know if it is going to end up there.
Once all the skb list users are updated in tipc it will then be possible
to update them to use the unlocked variants of the skb list functions
and initialise the lock when we know the message will follow the receive
path.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
For these places are protected by rcu_read_lock, we change from
rcu_dereference_rtnl to rcu_dereference, as there is no need to
check if rtnl lock is held.
For these places are protected by rtnl_lock, we change from
rcu_dereference_rtnl to rtnl_dereference/rcu_dereference_protected,
as no extra memory barriers are needed under rtnl_lock() which also
protects tn->bearer_list[] and dev->tipc_ptr/b->media_ptr updating.
rcu_dereference_rtnl will be only used in the places where it could
be under rcu_read_lock or rtnl_lock.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tipc_udp_enable and tipc_udp_disable are called under rtnl_lock,
ub->ubsock could never be NULL in tipc_udp_disable and cleanup_bearer,
so remove the check.
Also remove the one in tipc_udp_enable by adding "free" label.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro TIPC_BC_RETR_LIM is always used in combination with 'jiffies',
so we can just as well perform the addition in the macro itself. This
way, we get a few shorter code lines and one less line break.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As other udp/ip tunnels do, tipc udp media should also have a
lockless dst_cache supported on its tx path.
Here we add dst_cache into udp_replicast to support dst cache
for both rmcast and rcast, and rmcast uses ub->rcast and each
rcast uses its own node in ub->rcast.list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename the inline function msg_get_wrapped() to the more
comprehensible msg_inner_hdr().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We increase the allocated headroom for the buffer copies to be
retransmitted. This eliminates the need for the lower stack levels
(UDP/IP/L2) to expand the headroom in order to add their own headers.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a4dc70d46c ("tipc: extend link reset criteria for stale
packet retransmission") we made link retransmission failure events
dependent on the link tolerance, and not only of the number of failed
retransmission attempts, as we did earlier. This works well. However,
keeping the original, additional criteria of 99 failed retransmissions
is now redundant, and may in some cases lead to failure detection
times in the order of minutes instead of the expected 1.5 sec link
tolerance value.
We now remove this criteria altogether.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix an uninit-value issue, reported by syzbot:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:981
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
memchr+0xce/0x110 lib/string.c:981
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_disable+0x2a1/0x480 net/tipc/netlink_compat.c:449
__tipc_nl_compat_doit net/tipc/netlink_compat.c:327 [inline]
tipc_nl_compat_doit+0x3ac/0xb00 net/tipc/netlink_compat.c:360
tipc_nl_compat_handle net/tipc/netlink_compat.c:1178 [inline]
tipc_nl_compat_recv+0x1b1b/0x27b0 net/tipc/netlink_compat.c:1281
TLV_GET_DATA_LEN() may return a negtive int value, which will be
used as size_t (becoming a big unsigned long) passed into memchr,
cause this issue.
Similar to what it does in tipc_nl_compat_bearer_enable(), this
fix is to return -EINVAL when TLV_GET_DATA_LEN() is negtive in
tipc_nl_compat_bearer_disable(), as well as in
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
v1->v2:
- add the missing Fixes tags per Eric's request.
Fixes: 0762216c0a ("tipc: fix uninit-value in tipc_nl_compat_bearer_enable")
Fixes: 8b66fee7f8 ("tipc: fix uninit-value in tipc_nl_compat_link_reset_stats")
Reported-by: syzbot+30eaa8bf392f7fafffaf@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_nl_compat_bearer_set() is only called by tipc_nl_compat_link_set()
which already does the check for msg->req check, so remove it from
tipc_nl_compat_bearer_set(), and do the same in tipc_nl_compat_media_set().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misalignment of policy statement in netlink.c due to automatic
spatch code transformation.
Fixes: 3b0f31f2b8 ("genetlink: make policy common to family")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a dst defcnt leak, which can be reproduced by doing:
# ip net a c; ip net a s; modprobe tipc
# ip net e s ip l a n eth1 type veth peer n eth1 netns c
# ip net e c ip l s lo up; ip net e c ip l s eth1 up
# ip net e s ip l s lo up; ip net e s ip l s eth1 up
# ip net e c ip a a 1.1.1.2/8 dev eth1
# ip net e s ip a a 1.1.1.1/8 dev eth1
# ip net e c tipc b e m udp n u1 localip 1.1.1.2
# ip net e s tipc b e m udp n u1 localip 1.1.1.1
# ip net d c; ip net d s; rmmod tipc
and it will get stuck and keep logging the error:
unregister_netdevice: waiting for lo to become free. Usage count = 1
The cause is that a dst is held by the udp sock's sk_rx_dst set on udp rx
path with udp_early_demux == 1, and this dst (eventually holding lo dev)
can't be released as bearer's removal in tipc pernet .exit happens after
lo dev's removal, default_device pernet .exit.
"There are two distinct types of pernet_operations recognized: subsys and
device. At creation all subsys init functions are called before device
init functions, and at destruction all device exit functions are called
before subsys exit function."
So by calling register_pernet_device instead to register tipc_net_ops, the
pernet .exit() will be invoked earlier than loopback dev's removal when a
netns is being destroyed, as fou/gue does.
Note that vxlan and geneve udp tunnels don't have this issue, as the udp
sock is released in their device ndo_stop().
This fix is also necessary for tipc dst_cache, which will hold dsts on tx
path and I will introduce in my next patch.
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_tunnel(6)_xmit_skb() called by tipc_udp_xmit() expects a tunnel device
to count packets on dev->tstats, a perpcu variable. However, TIPC is using
udp tunnel with no tunnel device, and pass the lower dev, like veth device
that only initializes dev->lstats(a perpcu variable) when creating it.
Later iptunnel_xmit_stats() called by ip(6)tunnel_xmit() thinks the dev as
a tunnel device, and uses dev->tstats instead of dev->lstats. tstats' each
pointer points to a bigger struct than lstats, so when tstats->tx_bytes is
increased, other percpu variable's members could be overwritten.
syzbot has reported quite a few crashes due to fib_nh_common percpu member
'nhc_pcpu_rth_output' overwritten, call traces are like:
BUG: KASAN: slab-out-of-bounds in rt_cache_valid+0x158/0x190
net/ipv4/route.c:1556
rt_cache_valid+0x158/0x190 net/ipv4/route.c:1556
__mkroute_output net/ipv4/route.c:2332 [inline]
ip_route_output_key_hash_rcu+0x819/0x2d50 net/ipv4/route.c:2564
ip_route_output_key_hash+0x1ef/0x360 net/ipv4/route.c:2393
__ip_route_output_key include/net/route.h:125 [inline]
ip_route_output_flow+0x28/0xc0 net/ipv4/route.c:2651
ip_route_output_key include/net/route.h:135 [inline]
...
or:
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:dst_dev_put+0x24/0x290 net/core/dst.c:168
<IRQ>
rt_fibinfo_free_cpus net/ipv4/fib_semantics.c:200 [inline]
free_fib_info_rcu+0x2e1/0x490 net/ipv4/fib_semantics.c:217
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2437 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2716 [inline]
rcu_process_callbacks+0x100a/0x1ac0 kernel/rcu/tree.c:2697
...
The issue exists since tunnel stats update is moved to iptunnel_xmit by
Commit 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()"),
and here to fix it by passing a NULL tunnel dev to udp_tunnel(6)_xmit_skb
so that the packets counting won't happen on dev->tstats.
Reported-by: syzbot+9d4c12bfd45a58738d0a@syzkaller.appspotmail.com
Reported-by: syzbot+a9e23ea2aa21044c2798@syzkaller.appspotmail.com
Reported-by: syzbot+c4c4b2bb358bb936ad7e@syzkaller.appspotmail.com
Reported-by: syzbot+0290d2290a607e035ba1@syzkaller.appspotmail.com
Reported-by: syzbot+a43d8d4e7e8a7a9e149e@syzkaller.appspotmail.com
Reported-by: syzbot+a47c5f4c6c00fc1ed16e@syzkaller.appspotmail.com
Fixes: 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In patch series, commit 9195948fbf ("tipc: improve TIPC throughput by
Gap ACK blocks"), as for simplicity, the repeated retransmit failures'
detection in the function - "tipc_link_retrans()" was kept there for
broadcast retransmissions only.
This commit now reapplies this feature for link unicast retransmissions
that has been done via the function - "tipc_link_advance_transmq()".
Also, the "tipc_link_retrans()" is renamed to "tipc_link_bc_retrans()"
as it is used only for broadcast.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) called by
tipc_topsrv_create_listener() in the initialization process
of tipc_init_net(), so tipc_socket_init() must be execute before that.
Meanwhile, tipc_net_id need to be initialized when sock_create()
called, and tipc_socket_init() is no need to be called for each namespace.
I add a variable tipc_topsrv_net_ops, and split the
register_pernet_subsys() of tipc into two parts, and split
tipc_socket_init() with initialization of pernet params.
By the way, I fixed resources rollback error when tipc_bcast_init()
failed in tipc_init_net().
Fixes: 7e27e8d613 ("tipc: switch order of device registration to fix a crash")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com
Reviewed-by: Kang Zhou <zhoukang7@huawei.com>
Reviewed-by: Suanming Mou <mousuanming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) is called by
tipc_topsrv_create_listener() in the initialization process
of tipc_net_ops, tipc_socket_init() must be execute before that.
I move tipc_socket_init() into function tipc_init_net().
Fixes: 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reviewed-by: Kang Zhou <zhoukang7@huawei.com>
Reviewed-by: Suanming Mou <mousuanming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc is loaded while many processes try to create a TIPC socket,
a crash occurs:
PANIC: Unable to handle kernel paging request at virtual
address "dfff20000000021d"
pc : tipc_sk_create+0x374/0x1180 [tipc]
lr : tipc_sk_create+0x374/0x1180 [tipc]
Exception class = DABT (current EL), IL = 32 bits
Call trace:
tipc_sk_create+0x374/0x1180 [tipc]
__sock_create+0x1cc/0x408
__sys_socket+0xec/0x1f0
__arm64_sys_socket+0x74/0xa8
...
This is due to race between sock_create and unfinished
register_pernet_device. tipc_sk_insert tries to do
"net_generic(net, tipc_net_id)".
but tipc_net_id is not initialized yet.
So switch the order of the two to close the race.
This can be reproduced with multiple processes doing socket(AF_TIPC, ...)
and one process doing module removal.
Fixes: a62fbccecd ("tipc: make subscriber server support net namespace")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reviewed-by: Xiaogang Wang <wangxiaogang3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bd
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien
David S. Miller
Xin Long
Jon Maloy
Chris Packham
John Rutherford
Taras Kondratiuk
Christophe JAILLET
Linus Torvalds
Matteo Croce
Mauro Carvalho Chehab
Thomas Gleixner
Junwei Hu
Parthasarathy Bhuvaragan
Johannes Berg