If per-zone LRU accounting is available then there is no point
approximating whether reclaim and compaction should retry based on pgdat
statistics. This is effectively a revert of "mm, vmstat: remove zone
and node double accounting by approximating retries" with the difference
that inactive/active stats are still available. This preserves the
history of why the approximation was retried and why it had to be
reverted to handle OOM kills on 32-bit systems.
Link: http://lkml.kernel.org/r/1469110261-7365-4-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The number of LRU pages, dirty pages and writeback pages must be
accounted for on both zones and nodes because of the reclaim retry
logic, compaction retry logic and highmem calculations all depending on
per-zone stats.
Many lowmem allocations are immune from OOM kill due to a check in
__alloc_pages_may_oom for (ac->high_zoneidx < ZONE_NORMAL) since commit
03668b3ceb ("oom: avoid oom killer for lowmem allocations"). The
exception is costly high-order allocations or allocations that cannot
fail. If the __alloc_pages_may_oom avoids OOM-kill for low-order lowmem
allocations then it would fall through to __alloc_pages_direct_compact.
This patch will blindly retry reclaim for zone-constrained allocations
in should_reclaim_retry up to MAX_RECLAIM_RETRIES. This is not ideal
but without per-zone stats there are not many alternatives. The impact
it that zone-constrained allocations may delay before considering the
OOM killer.
As there is no guarantee enough memory can ever be freed to satisfy
compaction, this patch avoids retrying compaction for zone-contrained
allocations.
In combination, that means that the per-node stats can be used when
deciding whether to continue reclaim using a rough approximation. While
it is possible this will make the wrong decision on occasion, it will
not infinite loop as the number of reclaim attempts is capped by
MAX_RECLAIM_RETRIES.
The final step is calculating the number of dirtyable highmem pages. As
those calculations only care about the global count of file pages in
highmem. This patch uses a global counter used instead of per-zone
stats as it is sufficient.
In combination, this allows the per-zone LRU and dirty state counters to
be removed.
[mgorman@techsingularity.net: fix acct_highmem_file_pages()]
Link: http://lkml.kernel.org/r/1468853426-12858-4-git-send-email-mgorman@techsingularity.netLink: http://lkml.kernel.org/r/1467970510-21195-35-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Suggested by: Michal Hocko <mhocko@kernel.org>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a number of stats that were previously accessible via zoneinfo
that are now invisible. While it is possible to create a new file for
the node stats, this may be missed by users. Instead this patch prints
the stats under the first populated zone in /proc/zoneinfo.
Link: http://lkml.kernel.org/r/1467970510-21195-34-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vmstat allocstall was fairly useful in the general sense but
node-based LRUs change that. It's important to know if a stall was for
an address-limited allocation request as this will require skipping
pages from other zones. This patch adds pgstall_* counters to replace
allocstall. The sum of the counters will equal the old allocstall so it
can be trivially recalculated. A high number of address-limited
allocation requests may result in a lot of useless LRU scanning for
suitable pages.
As address-limited allocations require pages to be skipped, it's
important to know how much useless LRU scanning took place so this patch
adds pgskip* counters. This yields the following model
1. The number of address-space limited stalls can be accounted for (pgstall)
2. The amount of useless work required to reclaim the data is accounted (pgskip)
3. The total number of scans is available from pgscan_kswapd and pgscan_direct
so from that the ratio of useful to useless scans can be calculated.
[mgorman@techsingularity.net: s/pgstall/allocstall/]
Link: http://lkml.kernel.org/r/1468404004-5085-3-git-send-email-mgorman@techsingularity.netLink: http://lkml.kernel.org/r/1467970510-21195-33-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fair zone allocation policy interleaves allocation requests between
zones to avoid an age inversion problem whereby new pages are reclaimed
to balance a zone. Reclaim is now node-based so this should no longer
be an issue and the fair zone allocation policy is not free. This patch
removes it.
Link: http://lkml.kernel.org/r/1467970510-21195-30-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reclaim is now node-based, it follows that page write activity due to
page reclaim should also be accounted for on the node. For consistency,
also account page writes and page dirtying on a per-node basis.
After this patch, there are a few remaining zone counters that may appear
strange but are fine. NUMA stats are still per-zone as this is a
user-space interface that tools consume. NR_MLOCK, NR_SLAB_*,
NR_PAGETABLE, NR_KERNEL_STACK and NR_BOUNCE are all allocations that
potentially pin low memory and cannot trivially be reclaimed on demand.
This information is still useful for debugging a page allocation failure
warning.
Link: http://lkml.kernel.org/r/1467970510-21195-21-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are now a number of accounting oddities such as mapped file pages
being accounted for on the node while the total number of file pages are
accounted on the zone. This can be coped with to some extent but it's
confusing so this patch moves the relevant file-based accounted. Due to
throttling logic in the page allocator for reliable OOM detection, it is
still necessary to track dirty and writeback pages on a per-zone basis.
[mgorman@techsingularity.net: fix NR_ZONE_WRITE_PENDING accounting]
Link: http://lkml.kernel.org/r/1468404004-5085-5-git-send-email-mgorman@techsingularity.net
Link: http://lkml.kernel.org/r/1467970510-21195-20-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reclaim makes decisions based on the number of pages that are mapped but
it's mixing node and zone information. Account NR_FILE_MAPPED and
NR_ANON_PAGES pages on the node.
Link: http://lkml.kernel.org/r/1467970510-21195-18-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Working set and refault detection is still zone-based, fix it.
Link: http://lkml.kernel.org/r/1467970510-21195-16-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the LRU lists from the zone to the node and related data such
as counters, tracing, congestion tracking and writeback tracking.
Unfortunately, due to reclaim and compaction retry logic, it is
necessary to account for the number of LRU pages on both zone and node
logic. Most reclaim logic is based on the node counters but the retry
logic uses the zone counters which do not distinguish inactive and
active sizes. It would be possible to leave the LRU counters on a
per-zone basis but it's a heavier calculation across multiple cache
lines that is much more frequent than the retry checks.
Other than the LRU counters, this is mostly a mechanical patch but note
that it introduces a number of anomalies. For example, the scans are
per-zone but using per-node counters. We also mark a node as congested
when a zone is congested. This causes weird problems that are fixed
later but is easier to review.
In the event that there is excessive overhead on 32-bit systems due to
the nodes being on LRU then there are two potential solutions
1. Long-term isolation of highmem pages when reclaim is lowmem
When pages are skipped, they are immediately added back onto the LRU
list. If lowmem reclaim persisted for long periods of time, the same
highmem pages get continually scanned. The idea would be that lowmem
keeps those pages on a separate list until a reclaim for highmem pages
arrives that splices the highmem pages back onto the LRU. It potentially
could be implemented similar to the UNEVICTABLE list.
That would reduce the skip rate with the potential corner case is that
highmem pages have to be scanned and reclaimed to free lowmem slab pages.
2. Linear scan lowmem pages if the initial LRU shrink fails
This will break LRU ordering but may be preferable and faster during
memory pressure than skipping LRU pages.
Link: http://lkml.kernel.org/r/1467970510-21195-4-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patchset: "Move LRU page reclaim from zones to nodes v9"
This series moves LRUs from the zones to the node. While this is a
current rebase, the test results were based on mmotm as of June 23rd.
Conceptually, this series is simple but there are a lot of details.
Some of the broad motivations for this are;
1. The residency of a page partially depends on what zone the page was
allocated from. This is partially combatted by the fair zone allocation
policy but that is a partial solution that introduces overhead in the
page allocator paths.
2. Currently, reclaim on node 0 behaves slightly different to node 1. For
example, direct reclaim scans in zonelist order and reclaims even if
the zone is over the high watermark regardless of the age of pages
in that LRU. Kswapd on the other hand starts reclaim on the highest
unbalanced zone. A difference in distribution of file/anon pages due
to when they were allocated results can result in a difference in
again. While the fair zone allocation policy mitigates some of the
problems here, the page reclaim results on a multi-zone node will
always be different to a single-zone node.
it was scheduled on as a result.
3. kswapd and the page allocator scan zones in the opposite order to
avoid interfering with each other but it's sensitive to timing. This
mitigates the page allocator using pages that were allocated very recently
in the ideal case but it's sensitive to timing. When kswapd is allocating
from lower zones then it's great but during the rebalancing of the highest
zone, the page allocator and kswapd interfere with each other. It's worse
if the highest zone is small and difficult to balance.
4. slab shrinkers are node-based which makes it harder to identify the exact
relationship between slab reclaim and LRU reclaim.
The reason we have zone-based reclaim is that we used to have
large highmem zones in common configurations and it was necessary
to quickly find ZONE_NORMAL pages for reclaim. Today, this is much
less of a concern as machines with lots of memory will (or should) use
64-bit kernels. Combinations of 32-bit hardware and 64-bit hardware are
rare. Machines that do use highmem should have relatively low highmem:lowmem
ratios than we worried about in the past.
Conceptually, moving to node LRUs should be easier to understand. The
page allocator plays fewer tricks to game reclaim and reclaim behaves
similarly on all nodes.
The series has been tested on a 16 core UMA machine and a 2-socket 48
core NUMA machine. The UMA results are presented in most cases as the NUMA
machine behaved similarly.
pagealloc
---------
This is a microbenchmark that shows the benefit of removing the fair zone
allocation policy. It was tested uip to order-4 but only orders 0 and 1 are
shown as the other orders were comparable.
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
Min total-odr0-1 490.00 ( 0.00%) 457.00 ( 6.73%)
Min total-odr0-2 347.00 ( 0.00%) 329.00 ( 5.19%)
Min total-odr0-4 288.00 ( 0.00%) 273.00 ( 5.21%)
Min total-odr0-8 251.00 ( 0.00%) 239.00 ( 4.78%)
Min total-odr0-16 234.00 ( 0.00%) 222.00 ( 5.13%)
Min total-odr0-32 223.00 ( 0.00%) 211.00 ( 5.38%)
Min total-odr0-64 217.00 ( 0.00%) 208.00 ( 4.15%)
Min total-odr0-128 214.00 ( 0.00%) 204.00 ( 4.67%)
Min total-odr0-256 250.00 ( 0.00%) 230.00 ( 8.00%)
Min total-odr0-512 271.00 ( 0.00%) 269.00 ( 0.74%)
Min total-odr0-1024 291.00 ( 0.00%) 282.00 ( 3.09%)
Min total-odr0-2048 303.00 ( 0.00%) 296.00 ( 2.31%)
Min total-odr0-4096 311.00 ( 0.00%) 309.00 ( 0.64%)
Min total-odr0-8192 316.00 ( 0.00%) 314.00 ( 0.63%)
Min total-odr0-16384 317.00 ( 0.00%) 315.00 ( 0.63%)
Min total-odr1-1 742.00 ( 0.00%) 712.00 ( 4.04%)
Min total-odr1-2 562.00 ( 0.00%) 530.00 ( 5.69%)
Min total-odr1-4 457.00 ( 0.00%) 433.00 ( 5.25%)
Min total-odr1-8 411.00 ( 0.00%) 381.00 ( 7.30%)
Min total-odr1-16 381.00 ( 0.00%) 356.00 ( 6.56%)
Min total-odr1-32 372.00 ( 0.00%) 346.00 ( 6.99%)
Min total-odr1-64 372.00 ( 0.00%) 343.00 ( 7.80%)
Min total-odr1-128 375.00 ( 0.00%) 351.00 ( 6.40%)
Min total-odr1-256 379.00 ( 0.00%) 351.00 ( 7.39%)
Min total-odr1-512 385.00 ( 0.00%) 355.00 ( 7.79%)
Min total-odr1-1024 386.00 ( 0.00%) 358.00 ( 7.25%)
Min total-odr1-2048 390.00 ( 0.00%) 362.00 ( 7.18%)
Min total-odr1-4096 390.00 ( 0.00%) 362.00 ( 7.18%)
Min total-odr1-8192 388.00 ( 0.00%) 363.00 ( 6.44%)
This shows a steady improvement throughout. The primary benefit is from
reduced system CPU usage which is obvious from the overall times;
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
User 189.19 191.80
System 2604.45 2533.56
Elapsed 2855.30 2786.39
The vmstats also showed that the fair zone allocation policy was definitely
removed as can be seen here;
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v8
DMA32 allocs 28794729769 0
Normal allocs 48432501431 77227309877
Movable allocs 0 0
tiobench on ext4
----------------
tiobench is a benchmark that artifically benefits if old pages remain resident
while new pages get reclaimed. The fair zone allocation policy mitigates this
problem so pages age fairly. While the benchmark has problems, it is important
that tiobench performance remains constant as it implies that page aging
problems that the fair zone allocation policy fixes are not re-introduced.
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
Min PotentialReadSpeed 89.65 ( 0.00%) 90.21 ( 0.62%)
Min SeqRead-MB/sec-1 82.68 ( 0.00%) 82.01 ( -0.81%)
Min SeqRead-MB/sec-2 72.76 ( 0.00%) 72.07 ( -0.95%)
Min SeqRead-MB/sec-4 75.13 ( 0.00%) 74.92 ( -0.28%)
Min SeqRead-MB/sec-8 64.91 ( 0.00%) 65.19 ( 0.43%)
Min SeqRead-MB/sec-16 62.24 ( 0.00%) 62.22 ( -0.03%)
Min RandRead-MB/sec-1 0.88 ( 0.00%) 0.88 ( 0.00%)
Min RandRead-MB/sec-2 0.95 ( 0.00%) 0.92 ( -3.16%)
Min RandRead-MB/sec-4 1.43 ( 0.00%) 1.34 ( -6.29%)
Min RandRead-MB/sec-8 1.61 ( 0.00%) 1.60 ( -0.62%)
Min RandRead-MB/sec-16 1.80 ( 0.00%) 1.90 ( 5.56%)
Min SeqWrite-MB/sec-1 76.41 ( 0.00%) 76.85 ( 0.58%)
Min SeqWrite-MB/sec-2 74.11 ( 0.00%) 73.54 ( -0.77%)
Min SeqWrite-MB/sec-4 80.05 ( 0.00%) 80.13 ( 0.10%)
Min SeqWrite-MB/sec-8 72.88 ( 0.00%) 73.20 ( 0.44%)
Min SeqWrite-MB/sec-16 75.91 ( 0.00%) 76.44 ( 0.70%)
Min RandWrite-MB/sec-1 1.18 ( 0.00%) 1.14 ( -3.39%)
Min RandWrite-MB/sec-2 1.02 ( 0.00%) 1.03 ( 0.98%)
Min RandWrite-MB/sec-4 1.05 ( 0.00%) 0.98 ( -6.67%)
Min RandWrite-MB/sec-8 0.89 ( 0.00%) 0.92 ( 3.37%)
Min RandWrite-MB/sec-16 0.92 ( 0.00%) 0.93 ( 1.09%)
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 approx-v9
User 645.72 525.90
System 403.85 331.75
Elapsed 6795.36 6783.67
This shows that the series has little or not impact on tiobench which is
desirable and a reduction in system CPU usage. It indicates that the fair
zone allocation policy was removed in a manner that didn't reintroduce
one class of page aging bug. There were only minor differences in overall
reclaim activity
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
Minor Faults 645838 647465
Major Faults 573 640
Swap Ins 0 0
Swap Outs 0 0
DMA allocs 0 0
DMA32 allocs 46041453 44190646
Normal allocs 78053072 79887245
Movable allocs 0 0
Allocation stalls 24 67
Stall zone DMA 0 0
Stall zone DMA32 0 0
Stall zone Normal 0 2
Stall zone HighMem 0 0
Stall zone Movable 0 65
Direct pages scanned 10969 30609
Kswapd pages scanned 93375144 93492094
Kswapd pages reclaimed 93372243 93489370
Direct pages reclaimed 10969 30609
Kswapd efficiency 99% 99%
Kswapd velocity 13741.015 13781.934
Direct efficiency 100% 100%
Direct velocity 1.614 4.512
Percentage direct scans 0% 0%
kswapd activity was roughly comparable. There were differences in direct
reclaim activity but negligible in the context of the overall workload
(velocity of 4 pages per second with the patches applied, 1.6 pages per
second in the baseline kernel).
pgbench read-only large configuration on ext4
---------------------------------------------
pgbench is a database benchmark that can be sensitive to page reclaim
decisions. This also checks if removing the fair zone allocation policy
is safe
pgbench Transactions
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v8
Hmean 1 188.26 ( 0.00%) 189.78 ( 0.81%)
Hmean 5 330.66 ( 0.00%) 328.69 ( -0.59%)
Hmean 12 370.32 ( 0.00%) 380.72 ( 2.81%)
Hmean 21 368.89 ( 0.00%) 369.00 ( 0.03%)
Hmean 30 382.14 ( 0.00%) 360.89 ( -5.56%)
Hmean 32 428.87 ( 0.00%) 432.96 ( 0.95%)
Negligible differences again. As with tiobench, overall reclaim activity
was comparable.
bonnie++ on ext4
----------------
No interesting performance difference, negligible differences on reclaim
stats.
paralleldd on ext4
------------------
This workload uses varying numbers of dd instances to read large amounts of
data from disk.
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v9
Amean Elapsd-1 186.04 ( 0.00%) 189.41 ( -1.82%)
Amean Elapsd-3 192.27 ( 0.00%) 191.38 ( 0.46%)
Amean Elapsd-5 185.21 ( 0.00%) 182.75 ( 1.33%)
Amean Elapsd-7 183.71 ( 0.00%) 182.11 ( 0.87%)
Amean Elapsd-12 180.96 ( 0.00%) 181.58 ( -0.35%)
Amean Elapsd-16 181.36 ( 0.00%) 183.72 ( -1.30%)
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
User 1548.01 1552.44
System 8609.71 8515.08
Elapsed 3587.10 3594.54
There is little or no change in performance but some drop in system CPU usage.
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v9
Minor Faults 362662 367360
Major Faults 1204 1143
Swap Ins 22 0
Swap Outs 2855 1029
DMA allocs 0 0
DMA32 allocs 31409797 28837521
Normal allocs 46611853 49231282
Movable allocs 0 0
Direct pages scanned 0 0
Kswapd pages scanned 40845270 40869088
Kswapd pages reclaimed 40830976 40855294
Direct pages reclaimed 0 0
Kswapd efficiency 99% 99%
Kswapd velocity 11386.711 11369.769
Direct efficiency 100% 100%
Direct velocity 0.000 0.000
Percentage direct scans 0% 0%
Page writes by reclaim 2855 1029
Page writes file 0 0
Page writes anon 2855 1029
Page reclaim immediate 771 1628
Sector Reads 293312636 293536360
Sector Writes 18213568 18186480
Page rescued immediate 0 0
Slabs scanned 128257 132747
Direct inode steals 181 56
Kswapd inode steals 59 1131
It basically shows that kswapd was active at roughly the same rate in
both kernels. There was also comparable slab scanning activity and direct
reclaim was avoided in both cases. There appears to be a large difference
in numbers of inodes reclaimed but the workload has few active inodes and
is likely a timing artifact.
stutter
-------
stutter simulates a simple workload. One part uses a lot of anonymous
memory, a second measures mmap latency and a third copies a large file.
The primary metric is checking for mmap latency.
stutter
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v8
Min mmap 16.6283 ( 0.00%) 13.4258 ( 19.26%)
1st-qrtle mmap 54.7570 ( 0.00%) 34.9121 ( 36.24%)
2nd-qrtle mmap 57.3163 ( 0.00%) 46.1147 ( 19.54%)
3rd-qrtle mmap 58.9976 ( 0.00%) 47.1882 ( 20.02%)
Max-90% mmap 59.7433 ( 0.00%) 47.4453 ( 20.58%)
Max-93% mmap 60.1298 ( 0.00%) 47.6037 ( 20.83%)
Max-95% mmap 73.4112 ( 0.00%) 82.8719 (-12.89%)
Max-99% mmap 92.8542 ( 0.00%) 88.8870 ( 4.27%)
Max mmap 1440.6569 ( 0.00%) 121.4201 ( 91.57%)
Mean mmap 59.3493 ( 0.00%) 42.2991 ( 28.73%)
Best99%Mean mmap 57.2121 ( 0.00%) 41.8207 ( 26.90%)
Best95%Mean mmap 55.9113 ( 0.00%) 39.9620 ( 28.53%)
Best90%Mean mmap 55.6199 ( 0.00%) 39.3124 ( 29.32%)
Best50%Mean mmap 53.2183 ( 0.00%) 33.1307 ( 37.75%)
Best10%Mean mmap 45.9842 ( 0.00%) 20.4040 ( 55.63%)
Best5%Mean mmap 43.2256 ( 0.00%) 17.9654 ( 58.44%)
Best1%Mean mmap 32.9388 ( 0.00%) 16.6875 ( 49.34%)
This shows a number of improvements with the worst-case outlier greatly
improved.
Some of the vmstats are interesting
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
Swap Ins 163 502
Swap Outs 0 0
DMA allocs 0 0
DMA32 allocs 618719206 1381662383
Normal allocs 891235743 564138421
Movable allocs 0 0
Allocation stalls 2603 1
Direct pages scanned 216787 2
Kswapd pages scanned 50719775 41778378
Kswapd pages reclaimed 41541765 41777639
Direct pages reclaimed 209159 0
Kswapd efficiency 81% 99%
Kswapd velocity 16859.554 14329.059
Direct efficiency 96% 0%
Direct velocity 72.061 0.001
Percentage direct scans 0% 0%
Page writes by reclaim 6215049 0
Page writes file 6215049 0
Page writes anon 0 0
Page reclaim immediate 70673 90
Sector Reads 81940800 81680456
Sector Writes 100158984 98816036
Page rescued immediate 0 0
Slabs scanned 1366954 22683
While this is not guaranteed in all cases, this particular test showed
a large reduction in direct reclaim activity. It's also worth noting
that no page writes were issued from reclaim context.
This series is not without its hazards. There are at least three areas
that I'm concerned with even though I could not reproduce any problems in
that area.
1. Reclaim/compaction is going to be affected because the amount of reclaim is
no longer targetted at a specific zone. Compaction works on a per-zone basis
so there is no guarantee that reclaiming a few THP's worth page pages will
have a positive impact on compaction success rates.
2. The Slab/LRU reclaim ratio is affected because the frequency the shrinkers
are called is now different. This may or may not be a problem but if it
is, it'll be because shrinkers are not called enough and some balancing
is required.
3. The anon/file reclaim ratio may be affected. Pages about to be dirtied are
distributed between zones and the fair zone allocation policy used to do
something very similar for anon. The distribution is now different but not
necessarily in any way that matters but it's still worth bearing in mind.
VM statistic counters for reclaim decisions are zone-based. If the kernel
is to reclaim on a per-node basis then we need to track per-node
statistics but there is no infrastructure for that. The most notable
change is that the old node_page_state is renamed to
sum_zone_node_page_state. The new node_page_state takes a pglist_data and
uses per-node stats but none exist yet. There is some renaming such as
vm_stat to vm_zone_stat and the addition of vm_node_stat and the renaming
of mod_state to mod_zone_state. Otherwise, this is mostly a mechanical
patch with no functional change. There is a lot of similarity between the
node and zone helpers which is unfortunate but there was no obvious way of
reusing the code and maintaining type safety.
Link: http://lkml.kernel.org/r/1467970510-21195-2-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's add ShmemHugePages and ShmemPmdMapped fields into meminfo and
smaps. It indicates how many times we allocate and map shmem THP.
NR_ANON_TRANSPARENT_HUGEPAGES is renamed to NR_ANON_THPS.
Link: http://lkml.kernel.org/r/1466021202-61880-27-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THP_FILE_ALLOC: how many times huge page was allocated and put page
cache.
THP_FILE_MAPPED: how many times file huge page was mapped.
Link: http://lkml.kernel.org/r/1466021202-61880-13-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram is very popular for some of the embedded world (e.g., TV, mobile
phones). On those system, zsmalloc's consumed memory size is never
trivial (one of example from real product system, total memory: 800M,
zsmalloc consumed: 150M), so we have used this out of tree patch to
monitor system memory behavior via /proc/vmstat.
With zsmalloc in vmstat, it helps in tracking down system behavior due
to memory usage.
[minchan@kernel.org: zsmalloc: follow up zsmalloc vmstat]
Link: http://lkml.kernel.org/r/20160607091737.GC23435@bbox
[akpm@linux-foundation.org: fix build with CONFIG_ZSMALLOC=m]
Link: http://lkml.kernel.org/r/1464919731-13255-1-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sangseok Lee <sangseok.lee@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Chan Gyun Jeong <chan.jeong@lge.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per the discussion with Joonsoo Kim [1], we need check the return value
of lookup_page_ext() for all call sites since it might return NULL in
some cases, although it is unlikely, i.e. memory hotplug.
Tested with ltp with "page_owner=0".
[1] http://lkml.kernel.org/r/20160519002809.GA10245@js1304-P5Q-DELUXE
[akpm@linux-foundation.org: fix build-breaking typos]
[arnd@arndb.de: fix build problems from lookup_page_ext]
Link: http://lkml.kernel.org/r/6285269.2CksypHdYp@wuerfel
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1464023768-31025-1-git-send-email-yang.shi@linaro.org
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cpu_stat_off variable is unecessary since we can check if a
workqueue request is pending otherwise. Removal of cpu_stat_off makes
it pretty easy for the vmstat shepherd to ensure that the proper things
happen.
Removing the state also removes all races related to it. Should a
workqueue not be scheduled as needed for vmstat_update then the shepherd
will notice and schedule it as needed. Should a workqueue be
unecessarily scheduled then the vmstat updater will disable it.
[akpm@linux-foundation.org: fix indentation, per Michal]
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1605061306460.17934@east.gentwo.org
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function call overhead of get_pfnblock_flags_mask() is measurable in
the page free paths. This patch uses an inlined version that is faster.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide /proc/sys/vm/stat_refresh to force an immediate update of
per-cpu into global vmstats: useful to avoid a sleep(2) or whatever
before checking counts when testing. Originally added to work around a
bug which left counts stranded indefinitely on a cpu going idle (an
inaccuracy magnified when small below-batch numbers represent "huge"
amounts of memory), but I believe that bug is now fixed: nonetheless,
this is still a useful knob.
Its schedule_on_each_cpu() is probably too expensive just to fold into
reading /proc/meminfo itself: give this mode 0600 to prevent abuse.
Allow a write or a read to do the same: nothing to read, but "grep -h
Shmem /proc/sys/vm/stat_refresh /proc/meminfo" is convenient. Oh, and
since global_page_state() itself is careful to disguise any underflow as
0, hack in an "Invalid argument" and pr_warn() if a counter is negative
after the refresh - this helped to fix a misaccounting of
NR_ISOLATED_FILE in my migration code.
But on recent kernels, I find that NR_ALLOC_BATCH and NR_PAGES_SCANNED
often go negative some of the time. I have not yet worked out why, but
have no evidence that it's actually harmful. Punt for the moment by
just ignoring the anomaly on those.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Ning Qu <quning@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
node_page_state() manually adds statistics per each zone and returns
total value for all zones. Whenever we add a new zone, we need to
consider this function and it's really troublesome. Make it handle all
zones by itself.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a system thats node's pfns are overlapped as follows:
-----pfn-------->
N0 N1 N2 N0 N1 N2
Therefore, we need to care this overlapping when iterating pfn range.
There are two places in vmstat.c that iterates pfn range and they don't
consider this overlapping. Add it.
Without this patch, above system could over count pageblock number on a
zone.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Count how many times we put a THP in split queue. Currently, it happens
on partial unmap of a THP.
Rapidly growing value can indicate that an application behaves
unfriendly wrt THP: often fault in huge page and then unmap part of it.
This leads to unnecessary memory fragmentation and the application may
require tuning.
The event also can help with debugging kernel [mis-]behaviour.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory compaction can be currently performed in several contexts:
- kswapd balancing a zone after a high-order allocation failure
- direct compaction to satisfy a high-order allocation, including THP
page fault attemps
- khugepaged trying to collapse a hugepage
- manually from /proc
The purpose of compaction is two-fold. The obvious purpose is to
satisfy a (pending or future) high-order allocation, and is easy to
evaluate. The other purpose is to keep overal memory fragmentation low
and help the anti-fragmentation mechanism. The success wrt the latter
purpose is more
The current situation wrt the purposes has a few drawbacks:
- compaction is invoked only when a high-order page or hugepage is not
available (or manually). This might be too late for the purposes of
keeping memory fragmentation low.
- direct compaction increases latency of allocations. Again, it would
be better if compaction was performed asynchronously to keep
fragmentation low, before the allocation itself comes.
- (a special case of the previous) the cost of compaction during THP
page faults can easily offset the benefits of THP.
- kswapd compaction appears to be complex, fragile and not working in
some scenarios. It could also end up compacting for a high-order
allocation request when it should be reclaiming memory for a later
order-0 request.
To improve the situation, we should be able to benefit from an
equivalent of kswapd, but for compaction - i.e. a background thread
which responds to fragmentation and the need for high-order allocations
(including hugepages) somewhat proactively.
One possibility is to extend the responsibilities of kswapd, which could
however complicate its design too much. It should be better to let
kswapd handle reclaim, as order-0 allocations are often more critical
than high-order ones.
Another possibility is to extend khugepaged, but this kthread is a
single instance and tied to THP configs.
This patch goes with the option of a new set of per-node kthreads called
kcompactd, and lays the foundations, without introducing any new
tunables. The lifecycle mimics kswapd kthreads, including the memory
hotplug hooks.
For compaction, kcompactd uses the standard compaction_suitable() and
ompact_finished() criteria and the deferred compaction functionality.
Unlike direct compaction, it uses only sync compaction, as there's no
allocation latency to minimize.
This patch doesn't yet add a call to wakeup_kcompactd. The kswapd
compact/reclaim loop for high-order pages will be replaced by waking up
kcompactd in the next patch with the description of what's wrong with
the old approach.
Waking up of the kcompactd threads is also tied to kswapd activity and
follows these rules:
- we don't want to affect any fastpaths, so wake up kcompactd only from
the slowpath, as it's done for kswapd
- if kswapd is doing reclaim, it's more important than compaction, so
don't invoke kcompactd until kswapd goes to sleep
- the target order used for kswapd is passed to kcompactd
Future possible future uses for kcompactd include the ability to wake up
kcompactd on demand in special situations, such as when hugepages are
not available (currently not done due to __GFP_NO_KSWAPD) or when a
fragmentation event (i.e. __rmqueue_fallback()) occurs. It's also
possible to perform periodic compaction with kcompactd.
[arnd@arndb.de: fix build errors with kcompactd]
[paul.gortmaker@windriver.com: don't use modular references for non modular code]
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_PAGE_OWNER attempts to impose negligible runtime overhead when
enabled during compilation, but not actually enabled during runtime by
boot param page_owner=on. This overhead can be further reduced using
the static key mechanism, which this patch does.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The information in /sys/kernel/debug/page_owner includes the migratetype
of the pageblock the page belongs to. This is also checked against the
page's migratetype (as declared by gfp_flags during its allocation), and
the page is reported as Fallback if its migratetype differs from the
pageblock's one. t This is somewhat misleading because in fact fallback
allocation is not the only reason why these two can differ. It also
doesn't direcly provide the page's migratetype, although it's possible
to derive that from the gfp_flags.
It's arguably better to print both page and pageblock's migratetype and
leave the interpretation to the consumer than to suggest fallback
allocation as the only possible reason. While at it, we can print the
migratetypes as string the same way as /proc/pagetypeinfo does, as some
of the numeric values depend on kernel configuration. For that, this
patch moves the migratetype_names array from #ifdef CONFIG_PROC_FS part
of mm/vmstat.c to mm/page_alloc.c and exports it.
With the new format strings for flags, we can now also provide symbolic
page and gfp flags in the /sys/kernel/debug/page_owner file. This
replaces the positional printing of page flags as single letters, which
might have looked nicer, but was limited to a subset of flags, and
required the user to remember the letters.
Example page_owner entry after the patch:
Page allocated via order 0, mask 0x24213ca(GFP_HIGHUSER_MOVABLE|__GFP_COLD|__GFP_NOWARN|__GFP_NORETRY)
PFN 520 type Movable Block 1 type Movable Flags 0xfffff8001006c(referenced|uptodate|lru|active|mappedtodisk)
[<ffffffff811682c4>] __alloc_pages_nodemask+0x134/0x230
[<ffffffff811b4058>] alloc_pages_current+0x88/0x120
[<ffffffff8115e386>] __page_cache_alloc+0xe6/0x120
[<ffffffff8116ba6c>] __do_page_cache_readahead+0xdc/0x240
[<ffffffff8116bd05>] ondemand_readahead+0x135/0x260
[<ffffffff8116bfb1>] page_cache_sync_readahead+0x31/0x50
[<ffffffff81160523>] generic_file_read_iter+0x453/0x760
[<ffffffff811e0d57>] __vfs_read+0xa7/0xd0
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0eb77e9880 ("vmstat: make vmstat_updater deferrable again and
shut down on idle") made vmstat_shepherd deferrable. vmstat_update
itself is still useing standard timer which might interrupt idle task.
This is possible because "mm, vmstat: make quiet_vmstat lighter" removed
cancel_delayed_work from the quiet_vmstat.
Change vmstat_work to use DEFERRABLE_WORK to prevent from pointless
wakeups from the idle context.
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike has reported a considerable overhead of refresh_cpu_vm_stats from
the idle entry during pipe test:
12.89% [kernel] [k] refresh_cpu_vm_stats.isra.12
4.75% [kernel] [k] __schedule
4.70% [kernel] [k] mutex_unlock
3.14% [kernel] [k] __switch_to
This is caused by commit 0eb77e9880 ("vmstat: make vmstat_updater
deferrable again and shut down on idle") which has placed quiet_vmstat
into cpu_idle_loop. The main reason here seems to be that the idle
entry has to get over all zones and perform atomic operations for each
vmstat entry even though there might be no per cpu diffs. This is a
pointless overhead for _each_ idle entry.
Make sure that quiet_vmstat is as light as possible.
First of all it doesn't make any sense to do any local sync if the
current cpu is already set in oncpu_stat_off because vmstat_update puts
itself there only if there is nothing to do.
Then we can check need_update which should be a cheap way to check for
potential per-cpu diffs and only then do refresh_cpu_vm_stats.
The original patch also did cancel_delayed_work which we are not doing
here. There are two reasons for that. Firstly cancel_delayed_work from
idle context will blow up on RT kernels (reported by Mike):
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.5.0-rt3 #7
Hardware name: MEDION MS-7848/MS-7848, BIOS M7848W08.20C 09/23/2013
Call Trace:
dump_stack+0x49/0x67
___might_sleep+0xf5/0x180
rt_spin_lock+0x20/0x50
try_to_grab_pending+0x69/0x240
cancel_delayed_work+0x26/0xe0
quiet_vmstat+0x75/0xa0
cpu_idle_loop+0x38/0x3e0
cpu_startup_entry+0x13/0x20
start_secondary+0x114/0x140
And secondly, even on !RT kernels it might add some non trivial overhead
which is not necessary. Even if the vmstat worker wakes up and preempts
idle then it will be most likely a single shot noop because the stats
were already synced and so it would end up on the oncpu_stat_off anyway.
We just need to teach both vmstat_shepherd and vmstat_update to stop
scheduling the worker if there is nothing to do.
[mgalbraith@suse.de: cancel pending work of the cpu_stat_off CPU]
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Mike Galbraith <mgalbraith@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we detect that there is nothing to do just set the flag and do not
check if it was already set before. Races really do not matter. If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.
Since commit 0eb77e9880 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd. This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up. The VM_BUG_ON is therefore misleading and no more
appropriate. Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly. Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux doesn't have an ability to free pages lazy while other OS already
have been supported that named by madvise(MADV_FREE).
The gain is clear that kernel can discard freed pages rather than
swapping out or OOM if memory pressure happens.
Without memory pressure, freed pages would be reused by userspace
without another additional overhead(ex, page fault + allocation +
zeroing).
Jason Evans said:
: Facebook has been using MAP_UNINITIALIZED
: (https://lkml.org/lkml/2012/1/18/308) in some of its applications for
: several years, but there are operational costs to maintaining this
: out-of-tree in our kernel and in jemalloc, and we are anxious to retire it
: in favor of MADV_FREE. When we first enabled MAP_UNINITIALIZED it
: increased throughput for much of our workload by ~5%, and although the
: benefit has decreased using newer hardware and kernels, there is still
: enough benefit that we cannot reasonably retire it without a replacement.
:
: Aside from Facebook operations, there are numerous broadly used
: applications that would benefit from MADV_FREE. The ones that immediately
: come to mind are redis, varnish, and MariaDB. I don't have much insight
: into Android internals and development process, but I would hope to see
: MADV_FREE support eventually end up there as well to benefit applications
: linked with the integrated jemalloc.
:
: jemalloc will use MADV_FREE once it becomes available in the Linux kernel.
: In fact, jemalloc already uses MADV_FREE or equivalent everywhere it's
: available: *BSD, OS X, Windows, and Solaris -- every platform except Linux
: (and AIX, but I'm not sure it even compiles on AIX). The lack of
: MADV_FREE on Linux forced me down a long series of increasingly
: sophisticated heuristics for madvise() volume reduction, and even so this
: remains a common performance issue for people using jemalloc on Linux.
: Please integrate MADV_FREE; many people will benefit substantially.
How it works:
When madvise syscall is called, VM clears dirty bit of ptes of the
range. If memory pressure happens, VM checks dirty bit of page table
and if it found still "clean", it means it's a "lazyfree pages" so VM
could discard the page instead of swapping out. Once there was store
operation for the page before VM peek a page to reclaim, dirty bit is
set so VM can swap out the page instead of discarding.
One thing we should notice is that basically, MADV_FREE relies on dirty
bit in page table entry to decide whether VM allows to discard the page
or not. IOW, if page table entry includes marked dirty bit, VM
shouldn't discard the page.
However, as a example, if swap-in by read fault happens, page table
entry doesn't have dirty bit so MADV_FREE could discard the page
wrongly.
For avoiding the problem, MADV_FREE did more checks with PageDirty and
PageSwapCache. It worked out because swapped-in page lives on swap
cache and since it is evicted from the swap cache, the page has PG_dirty
flag. So both page flags check effectively prevent wrong discarding by
MADV_FREE.
However, a problem in above logic is that swapped-in page has PG_dirty
still after they are removed from swap cache so VM cannot consider the
page as freeable any more even if madvise_free is called in future.
Look at below example for detail.
ptr = malloc();
memset(ptr);
..
..
.. heavy memory pressure so all of pages are swapped out
..
..
var = *ptr; -> a page swapped-in and could be removed from
swapcache. Then, page table doesn't mark
dirty bit and page descriptor includes PG_dirty
..
..
madvise_free(ptr); -> It doesn't clear PG_dirty of the page.
..
..
..
.. heavy memory pressure again.
.. In this time, VM cannot discard the page because the page
.. has *PG_dirty*
To solve the problem, this patch clears PG_dirty if only the page is
owned exclusively by current process when madvise is called because
PG_dirty represents ptes's dirtiness in several processes so we could
clear it only if we own it exclusively.
Firstly, heavy users would be general allocators(ex, jemalloc, tcmalloc
and hope glibc supports it) and jemalloc/tcmalloc already have supported
the feature for other OS(ex, FreeBSD)
barrios@blaptop:~/benchmark/ebizzy$ lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 12
On-line CPU(s) list: 0-11
Thread(s) per core: 1
Core(s) per socket: 1
Socket(s): 12
NUMA node(s): 1
Vendor ID: GenuineIntel
CPU family: 6
Model: 2
Stepping: 3
CPU MHz: 3200.185
BogoMIPS: 6400.53
Virtualization: VT-x
Hypervisor vendor: KVM
Virtualization type: full
L1d cache: 32K
L1i cache: 32K
L2 cache: 4096K
NUMA node0 CPU(s): 0-11
ebizzy benchmark(./ebizzy -S 10 -n 512)
Higher avg is better.
vanilla-jemalloc MADV_free-jemalloc
1 thread
records: 10 records: 10
avg: 2961.90 avg: 12069.70
std: 71.96(2.43%) std: 186.68(1.55%)
max: 3070.00 max: 12385.00
min: 2796.00 min: 11746.00
2 thread
records: 10 records: 10
avg: 5020.00 avg: 17827.00
std: 264.87(5.28%) std: 358.52(2.01%)
max: 5244.00 max: 18760.00
min: 4251.00 min: 17382.00
4 thread
records: 10 records: 10
avg: 8988.80 avg: 27930.80
std: 1175.33(13.08%) std: 3317.33(11.88%)
max: 9508.00 max: 30879.00
min: 5477.00 min: 21024.00
8 thread
records: 10 records: 10
avg: 13036.50 avg: 33739.40
std: 170.67(1.31%) std: 5146.22(15.25%)
max: 13371.00 max: 40572.00
min: 12785.00 min: 24088.00
16 thread
records: 10 records: 10
avg: 11092.40 avg: 31424.20
std: 710.60(6.41%) std: 3763.89(11.98%)
max: 12446.00 max: 36635.00
min: 9949.00 min: 25669.00
32 thread
records: 10 records: 10
avg: 11067.00 avg: 34495.80
std: 971.06(8.77%) std: 2721.36(7.89%)
max: 12010.00 max: 38598.00
min: 9002.00 min: 30636.00
In summary, MADV_FREE is about much faster than MADV_DONTNEED.
This patch (of 12):
Add core MADV_FREE implementation.
[akpm@linux-foundation.org: small cleanups]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Mika Penttil <mika.penttila@nextfour.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jason Evans <je@fb.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Shaohua Li <shli@kernel.org>
Cc: <yalin.wang2010@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: "Shaohua Li" <shli@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Gang <gang.chen.5i5j@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Roland Dreier <roland@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Shaohua Li <shli@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch replaces THP_SPLIT with tree events: THP_SPLIT_PAGE,
THP_SPLIT_PAGE_FAILED and THP_SPLIT_PMD. It reflects the fact that we
are going to be able split PMD without the compound page and that
split_huge_page() can fail.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Christoph Lameter <cl@linux.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the vmstat updater is not deferrable as a result of commit
ba4877b9ca ("vmstat: do not use deferrable delayed work for
vmstat_update"). This in turn can cause multiple interruptions of the
applications because the vmstat updater may run at
Make vmstate_update deferrable again and provide a function that folds
the differentials when the processor is going to idle mode thus
addressing the issue of the above commit in a clean way.
Note that the shepherd thread will continue scanning the differentials
from another processor and will reenable the vmstat workers if it
detects any changes.
Fixes: ba4877b9ca ("vmstat: do not use deferrable delayed work for vmstat_update")
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel test robot has reported the following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000100
IP: [<c1074df6>] __queue_work+0x26/0x390
*pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53
Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe #1
Workqueue: events vmstat_shepherd
task: cb684600 ti: cb7ba000 task.ti: cb7ba000
EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0
EIP is at __queue_work+0x26/0x390
EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0
Stack:
Call Trace:
__queue_delayed_work+0xa1/0x160
queue_delayed_work_on+0x36/0x60
vmstat_shepherd+0xad/0xf0
process_one_work+0x1aa/0x4c0
worker_thread+0x41/0x440
kthread+0xb0/0xd0
ret_from_kernel_thread+0x21/0x40
The reason is that start_shepherd_timer schedules the shepherd work item
which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates
that workqueue so if the further initialization takes more than HZ we
might end up scheduling on a NULL vmstat_wq. This is really unlikely
but not impossible.
Fixes: 373ccbe592 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mod_zone_page_state() takes a "delta" integer argument. delta contains
the number of pages that should be added or subtracted from a struct
zone's vm_stat field.
If a zone is larger than 8TB this will cause overflows. E.g. for a
zone with a size slightly larger than 8TB the line
mod_zone_page_state(zone, NR_ALLOC_BATCH, zone->managed_pages);
in mm/page_alloc.c:free_area_init_core() will result in a negative
result for the NR_ALLOC_BATCH entry within the zone's vm_stat, since 8TB
contain 0x8xxxxxxx pages which will be sign extended to a negative
value.
Fix this by changing the delta argument to long type.
This could fix an early boot problem seen on s390, where we have a 9TB
system with only one node. ZONE_DMA contains 2GB and ZONE_NORMAL the
rest. The system is trying to allocate a GFP_DMA page but ZONE_DMA is
completely empty, so it tries to reclaim pages in an endless loop.
This was seen on a heavily patched 3.10 kernel. One possible
explaination seem to be the overflows caused by mod_zone_page_state().
Unfortunately I did not have the chance to verify that this patch
actually fixes the problem, since I don't have access to the system
right now. However the overflow problem does exist anyway.
Given the description that a system with slightly less than 8TB does
work, this seems to be a candidate for the observed problem.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa has reported that the system might basically livelock in
OOM condition without triggering the OOM killer.
The issue is caused by internal dependency of the direct reclaim on
vmstat counter updates (via zone_reclaimable) which are performed from
the workqueue context. If all the current workers get assigned to an
allocation request, though, they will be looping inside the allocator
trying to reclaim memory but zone_reclaimable can see stalled numbers so
it will consider a zone reclaimable even though it has been scanned way
too much. WQ concurrency logic will not consider this situation as a
congested workqueue because it relies that worker would have to sleep in
such a situation. This also means that it doesn't try to spawn new
workers or invoke the rescuer thread if the one is assigned to the
queue.
In order to fix this issue we need to do two things. First we have to
let wq concurrency code know that we are in trouble so we have to do a
short sleep. In order to prevent from issues handled by 0e093d9976
("writeback: do not sleep on the congestion queue if there are no
congested BDIs or if significant congestion is not being encountered in
the current zone") we limit the sleep only to worker threads which are
the ones of the interest anyway.
The second thing to do is to create a dedicated workqueue for vmstat and
mark it WQ_MEM_RECLAIM to note it participates in the reclaim and to
have a spare worker thread for it.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Tejun Heo <tj@kernel.org>
Cc: Cristopher Lameter <clameter@sgi.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Arkadiusz Miskiewicz <arekm@maven.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 016c13daa5 ("mm, page_alloc: use masks and shifts when
converting GFP flags to migrate types") has swapped MIGRATE_MOVABLE and
MIGRATE_RECLAIMABLE in the enum definition. However, migratetype_names
wasn't updated to reflect that.
As a result, the file /proc/pagetypeinfo shows the counts for Movable as
Reclaimable and vice versa.
Additionally, commit 0aaa29a56e ("mm, page_alloc: reserve pageblocks
for high-order atomic allocations on demand") introduced
MIGRATE_HIGHATOMIC, but did not add a letter to distinguish it into
show_migration_types(), so it doesn't appear in the listing of free
areas during page alloc failures or oom kills.
This patch fixes both problems. The atomic reserves will show with a
letter 'H' in the free areas listings.
Fixes: 016c13daa5 ("mm, page_alloc: use masks and shifts when converting GFP flags to migrate types")
Fixes: 0aaa29a56e ("mm, page_alloc: reserve pageblocks for high-order atomic allocations on demand")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
High-order watermark checking exists for two reasons -- kswapd high-order
awareness and protection for high-order atomic requests. Historically the
kernel depended on MIGRATE_RESERVE to preserve min_free_kbytes as
high-order free pages for as long as possible. This patch introduces
MIGRATE_HIGHATOMIC that reserves pageblocks for high-order atomic
allocations on demand and avoids using those blocks for order-0
allocations. This is more flexible and reliable than MIGRATE_RESERVE was.
A MIGRATE_HIGHORDER pageblock is created when an atomic high-order
allocation request steals a pageblock but limits the total number to 1% of
the zone. Callers that speculatively abuse atomic allocations for
long-lived high-order allocations to access the reserve will quickly fail.
Note that SLUB is currently not such an abuser as it reclaims at least
once. It is possible that the pageblock stolen has few suitable
high-order pages and will need to steal again in the near future but there
would need to be strong justification to search all pageblocks for an
ideal candidate.
The pageblocks are unreserved if an allocation fails after a direct
reclaim attempt.
The watermark checks account for the reserved pageblocks when the
allocation request is not a high-order atomic allocation.
The reserved pageblocks can not be used for order-0 allocations. This may
allow temporary wastage until a failed reclaim reassigns the pageblock.
This is deliberate as the intent of the reservation is to satisfy a
limited number of atomic high-order short-lived requests if the system
requires them.
The stutter benchmark was used to evaluate this but while it was running
there was a systemtap script that randomly allocated between 1 high-order
page and 12.5% of memory's worth of order-3 pages using GFP_ATOMIC. This
is much larger than the potential reserve and it does not attempt to be
realistic. It is intended to stress random high-order allocations from an
unknown source, show that there is a reduction in failures without
introducing an anomaly where atomic allocations are more reliable than
regular allocations. The amount of memory reserved varied throughout the
workload as reserves were created and reclaimed under memory pressure.
The allocation failures once the workload warmed up were as follows;
4.2-rc5-vanilla 70%
4.2-rc5-atomic-reserve 56%
The failure rate was also measured while building multiple kernels. The
failure rate was 14% but is 6% with this patch applied.
Overall, this is a small reduction but the reserves are small relative to
the number of allocation requests. In early versions of the patch, the
failure rate reduced by a much larger amount but that required much larger
reserves and perversely made atomic allocations seem more reliable than
regular allocations.
[yalin.wang2010@gmail.com: fix redundant check and a memory leak]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MIGRATE_RESERVE preserves an old property of the buddy allocator that
existed prior to fragmentation avoidance -- min_free_kbytes worth of pages
tended to remain contiguous until the only alternative was to fail the
allocation. At the time it was discovered that high-order atomic
allocations relied on this property so MIGRATE_RESERVE was introduced. A
later patch will introduce an alternative MIGRATE_HIGHATOMIC so this patch
deletes MIGRATE_RESERVE and supporting code so it'll be easier to review.
Note that this patch in isolation may look like a false regression if
someone was bisecting high-order atomic allocation failures.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With x86_64 (config http://ozlabs.org/~akpm/config-akpm2.txt) and old gcc
(4.4.4), drivers/base/node.c:node_read_meminfo() is using 2344 bytes of
stack. Uninlining node_page_state() reduces this to 440 bytes.
The stack consumption issue is fixed by newer gcc (4.8.4) however with
that compiler this patch reduces the node.o text size from 7314 bytes to
4578.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vmstat code uses "schedule_delayed_work_on()" to do the initial
startup of the delayed work on the right CPU, but then once it was
started it would use the non-cpu-specific "schedule_delayed_work()" to
re-schedule it on that CPU.
That just happened to schedule it on the same CPU historically (well, in
almost all situations), but the code _requires_ this work to be per-cpu,
and should say so explicitly rather than depend on the non-cpu-specific
scheduling to schedule on the current CPU.
The timer code is being changed to not be as single-minded in always
running things on the calling CPU.
See also commit 874bbfe600 ("workqueue: make sure delayed work run in
local cpu") that for now maintains the local CPU guarantees just in case
there are other broken users that depended on the accidental behavior.
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was noted that the vm stat shepherd runs every 2 seconds and that the
vmstat update is then scheduled 2 seconds in the future.
This yields an interval of double the time interval which is not desired.
Change the shepherd so that it does not delay the vmstat update on the
other cpu. We stil have to use schedule_delayed_work since we are using a
delayed_work_struct but we can set the delay to 0.
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vinayak Menon has reported that an excessive number of tasks was throttled
in the direct reclaim inside too_many_isolated() because NR_ISOLATED_FILE
was relatively high compared to NR_INACTIVE_FILE. However it turned out
that the real number of NR_ISOLATED_FILE was 0 and the per-cpu
vm_stat_diff wasn't transferred into the global counter.
vmstat_work which is responsible for the sync is defined as deferrable
delayed work which means that the defined timeout doesn't wake up an idle
CPU. A CPU might stay in an idle state for a long time and general effort
is to keep such a CPU in this state as long as possible which might lead
to all sorts of troubles for vmstat consumers as can be seen with the
excessive direct reclaim throttling.
This patch basically reverts 39bf6270f5 ("VM statistics: Make timer
deferrable") but it shouldn't cause any problems for idle CPUs because
only CPUs with an active per-cpu drift are woken up since 7cc36bbddd
("vmstat: on-demand vmstat workers v8") and CPUs which are idle for a
longer time shouldn't have per-cpu drift.
Fixes: 39bf6270f5 (VM statistics: Make timer deferrable)
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Vinayak Menon <vinmenon@codeaurora.org>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_COMPACTION=y, CONFIG_DEBUG_FS=n:
mm/vmstat.c:690: warning: 'frag_start' defined but not used
mm/vmstat.c:702: warning: 'frag_next' defined but not used
mm/vmstat.c:710: warning: 'frag_stop' defined but not used
mm/vmstat.c:715: warning: 'walk_zones_in_node' defined but not used
It's all a bit of a tangly mess and it's unclear why CONFIG_COMPACTION
figures in there at all. Move frag_start/frag_next/frag_stop and
migratetype_names[] into the existing CONFIG_PROC_FS block.
walk_zones_in_node() gets a special ifdef.
Also move the #include lines up to where #include lines live.
[axel.lin@ingics.com: fix build error when !CONFIG_PROC_FS]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These flushes deal with sequence number overflows, such as for long lived
threads. These are rare, but interesting from a debugging PoV. As such,
display the number of flushes when vmacache debugging is enabled.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the page owner tracking code which is introduced so far ago. It
is resident on Andrew's tree, though, nobody tried to upstream so it
remain as is. Our company uses this feature actively to debug memory leak
or to find a memory hogger so I decide to upstream this feature.
This functionality help us to know who allocates the page. When
allocating a page, we store some information about allocation in extra
memory. Later, if we need to know status of all pages, we can get and
analyze it from this stored information.
In previous version of this feature, extra memory is statically defined in
struct page, but, in this version, extra memory is allocated outside of
struct page. It enables us to turn on/off this feature at boottime
without considerable memory waste.
Although we already have tracepoint for tracing page allocation/free,
using it to analyze page owner is rather complex. We need to enlarge the
trace buffer for preventing overlapping until userspace program launched.
And, launched program continually dump out the trace buffer for later
analysis and it would change system behaviour with more possibility rather
than just keeping it in memory, so bad for debug.
Moreover, we can use page_owner feature further for various purposes. For
example, we can use it for fragmentation statistics implemented in this
patch. And, I also plan to implement some CMA failure debugging feature
using this interface.
I'd like to give the credit for all developers contributed this feature,
but, it's not easy because I don't know exact history. Sorry about that.
Below is people who has "Signed-off-by" in the patches in Andrew's tree.
Contributor:
Alexander Nyberg <alexn@dsv.su.se>
Mel Gorman <mgorman@suse.de>
Dave Hansen <dave@linux.vnet.ibm.com>
Minchan Kim <minchan@kernel.org>
Michal Nazarewicz <mina86@mina86.com>
Andrew Morton <akpm@linux-foundation.org>
Jungsoo Son <jungsoo.son@lge.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Jungsoo Son <jungsoo.son@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vmstat workers are used for folding counter differentials into the zone,
per node and global counters at certain time intervals. They currently
run at defined intervals on all processors which will cause some holdoff
for processors that need minimal intrusion by the OS.
The current vmstat_update mechanism depends on a deferrable timer firing
every other second by default which registers a work queue item that runs
on the local CPU, with the result that we have 1 interrupt and one
additional schedulable task on each CPU every 2 seconds If a workload
indeed causes VM activity or multiple tasks are running on a CPU, then
there are probably bigger issues to deal with.
However, some workloads dedicate a CPU for a single CPU bound task. This
is done in high performance computing, in high frequency financial
applications, in networking (Intel DPDK, EZchip NPS) and with the advent
of systems with more and more CPUs over time, this may become more and
more common to do since when one has enough CPUs one cares less about
efficiently sharing a CPU with other tasks and more about efficiently
monopolizing a CPU per task.
The difference of having this timer firing and workqueue kernel thread
scheduled per second can be enormous. An artificial test measuring the
worst case time to do a simple "i++" in an endless loop on a bare metal
system and under Linux on an isolated CPU with dynticks and with and
without this patch, have Linux match the bare metal performance (~700
cycles) with this patch and loose by couple of orders of magnitude (~200k
cycles) without it[*]. The loss occurs for something that just calculates
statistics. For networking applications, for example, this could be the
difference between dropping packets or sustaining line rate.
Statistics are important and useful, but it would be great if there would
be a way to not cause statistics gathering produce a huge performance
difference. This patche does just that.
This patch creates a vmstat shepherd worker that monitors the per cpu
differentials on all processors. If there are differentials on a
processor then a vmstat worker local to the processors with the
differentials is created. That worker will then start folding the diffs
in regular intervals. Should the worker find that there is no work to be
done then it will make the shepherd worker monitor the differentials
again.
With this patch it is possible then to have periods longer than
2 seconds without any OS event on a "cpu" (hardware thread).
The patch shows a very minor increased in system performance.
hackbench -s 512 -l 2000 -g 15 -f 25 -P
Results before the patch:
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 4.992
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 4.971
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 5.063
Hackbench after the patch:
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 4.973
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 4.990
Running in process mode with 15 groups using 50 file descriptors each (== 750 tasks)
Each sender will pass 2000 messages of 512 bytes
Time: 4.993
[fengguang.wu@intel.com: cpu_stat_off can be static]
Signed-off-by: Christoph Lameter <cl@linux.com>
Reviewed-by: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Max Krasnyansky <maxk@qti.qualcomm.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always mark pages with PageBalloon even if balloon compaction is disabled
and expose this mark in /proc/kpageflags as KPF_BALLOON.
Also this patch adds three counters into /proc/vmstat: "balloon_inflate",
"balloon_deflate" and "balloon_migrate". They accumulate balloon
activity. Current size of balloon is (balloon_inflate - balloon_deflate)
pages.
All generic balloon code now gathered under option CONFIG_MEMORY_BALLOON.
It should be selected by ballooning driver which wants use this feature.
Currently virtio-balloon is the only user.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When kswapd is awake reclaiming, the per-cpu stat thresholds are lowered
to get more accurate counts to avoid breaching watermarks. This
threshold update iterates over all possible CPUs which is unnecessary.
Only online CPUs need to be updated. If a new CPU is onlined,
refresh_zone_stat_thresholds() will set the thresholds correctly.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zone->pages_scanned is a write-intensive cache line during page reclaim
and it's also updated during page free. Move the counter into vmstat to
take advantage of the per-cpu updates and do not update it in the free
paths unless necessary.
On a small UMA machine running tiobench the difference is marginal. On
a 4-node machine the overhead is more noticable. Note that automatic
NUMA balancing was disabled for this test as otherwise the system CPU
overhead is unpredictable.
3.16.0-rc3 3.16.0-rc3 3.16.0-rc3
vanillarearrange-v5 vmstat-v5
User 746.94 759.78 774.56
System 65336.22 58350.98 32847.27
Elapsed 27553.52 27282.02 27415.04
Note that the overhead reduction will vary depending on where exactly
pages are allocated and freed.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman
Minchan Kim
Kirill A. Shutemov
Yang Shi
Christoph Lameter
Hugh Dickins
Joonsoo Kim
Vlastimil Babka
Michal Hocko
Heiko Carstens
Andrew Morton
Linus Torvalds
Michal Hocko
Davidlohr Bueso
Christoph Lameter
Konstantin Khlebnikov
Mel Gorman