Current WARN msg is only for the ati_ixp4x0 board, while this function
is used by mulitple platforms. So this one board specific warning
is not appropriate any more.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently when acpi_skip_timer_override is set, it only cover the
(source_irq == 0 && global_irq == 2) cases. While there is also
platform which need use this option and its global_irq is not 2.
This patch will extend acpi_skip_timer_override to cover all
timer overriding cases as long as the source irq is 0.
This is the first part of a fix to kernel bug bugzilla 40002:
"IRQ 0 assigned to VGA"
https://bugzilla.kernel.org/show_bug.cgi?id=40002
Reported-and-tested-by: Szymon Kowalczyk <fazerxlo@o2.pl>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull crypto fixes from Herbert Xu:
"This push fixes an unaligned fault on x86-32 with aesni-intel and an
RNG failure with atmel-rng (repeated bits)."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni-intel - fix unaligned cbc decrypt for x86-32
hwrng: atmel-rng - fix race condition leading to repeated bits
arm_dma_limit stores physical address of maximal address accessible by DMA,
so the phys_addr_t type makes much more sense for it instead of u32. This
patch fixes the following build warning:
arch/arm/mm/init.c:380: warning: comparison of distinct pointer types lacks a cast
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes the following sparse warnings:
arch/arm/mm/dma-mapping.c:231:15: warning: symbol 'consistent_base' was not
declared. Should it be static?
arch/arm/mm/dma-mapping.c:326:8: warning: symbol 'coherent_pool_size' was not
declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fix kernel-doc warnings in arch/x86/mm/ioremap.c and
arch/x86/mm/pageattr.c, just like this one:
Warning(arch/x86/mm/ioremap.c:204):
No description found for parameter 'phys_addr'
Warning(arch/x86/mm/ioremap.c:204):
Excess function parameter 'offset' description in 'ioremap_nocache'
Signed-off-by: Wanpeng Li <liwp@linux.vnet.ibm.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Wanpeng Li <liwp.linux@gmail.com>
Link: http://lkml.kernel.org/r/1339296652-2935-1-git-send-email-liwp.linux@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The latest GCC 4.8 does some more checking on type attributes that
break the build for ARCH=um -> fill them in. Specifically, the
"asmlinkage" attributes is now tested for consistency.
Signed-off-by: Martin Pelikan <pelikan@storkhole.cz>
Link: http://lkml.kernel.org/r/1339269731-10772-1-git-send-email-pelikan@storkhole.cz
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull powerpc fixes from Paul Mackerras:
"Two small fixes for powerpc:
- a fix for a regression since 3.2 that causes 4-second (or longer)
pauses
- a fix for a potential oops when loading kernel modules on 32-bit
embedded systems."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix kernel panic during kernel module load
powerpc/time: Sanity check of decrementer expiration is necessary
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Fix section mismatch warnings on 32-bit
x86/uv: Fix UV2 BAU legacy mode
x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space
x86, efi stub: Add .reloc section back into image
x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
x86/reboot: Fix a warning message triggered by stop_other_cpus()
x86/intel/moorestown: Change intel_scu_devices_create() to __devinit
x86/numa: Set numa_nodes_parsed at acpi_numa_memory_affinity_init()
x86/gart: Fix kmemleak warning
x86: mce: Add the dropped timer interval init back
x86/mce: Fix the MCE poll timer logic
Pull perf fixes from Ingo Molnar:
"A bit larger than what I'd wish for - half of it is due to hw driver
updates to Intel Ivy-Bridge which info got recently released,
cycles:pp should work there now too, amongst other things. (but we
are generally making exceptions for hardware enablement of this type.)
There are also callchain fixes in it - responding to mostly
theoretical (but valid) concerns. The tooling side sports perf.data
endianness/portability fixes which did not make it for the merge
window - and various other fixes as well."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
perf/x86: Check user address explicitly in copy_from_user_nmi()
perf/x86: Check if user fp is valid
perf: Limit callchains to 127
perf/x86: Allow multiple stacks
perf/x86: Update SNB PEBS constraints
perf/x86: Enable/Add IvyBridge hardware support
perf/x86: Implement cycles:p for SNB/IVB
perf/x86: Fix Intel shared extra MSR allocation
x86/decoder: Fix bsr/bsf/jmpe decoding with operand-size prefix
perf: Remove duplicate invocation on perf_event_for_each
perf uprobes: Remove unnecessary check before strlist__delete
perf symbols: Check for valid dso before creating map
perf evsel: Fix 32 bit values endianity swap for sample_id_all header
perf session: Handle endianity swap on sample_id_all header data
perf symbols: Handle different endians properly during symbol load
perf evlist: Pass third argument to ioctl explicitly
perf tools: Update ioctl documentation for PERF_IOC_FLAG_GROUP
perf tools: Make --version show kernel version instead of pull req tag
perf tools: Check if callchain is corrupted
perf callchain: Make callchain cursors TLS
...
It was reported that compiling for 32-bit caused a bunch of
section mismatch warnings:
VDSOSYM arch/x86/vdso/vdso32-syms.lds
LD arch/x86/vdso/built-in.o
LD arch/x86/built-in.o
WARNING: arch/x86/built-in.o(.data+0x5af0): Section mismatch in
reference from the variable test_nmi_ipi_callback_na.10451 to
the function .init.text:test_nmi_ipi_callback() [...]
WARNING: arch/x86/built-in.o(.data+0x5b04): Section mismatch in
reference from the variable nmi_unk_cb_na.10399 to the function
.init.text:nmi_unk_cb() The variable nmi_unk_cb_na.10399
references the function __init nmi_unk_cb() [...]
Both of these are attributed to the internal representation of
the nmiaction struct created during register_nmi_handler. The
reason for this is that those structs are not defined in the
init section whereas the rest of the code in nmi_selftest.c is.
To resolve this, I created a new #define,
register_nmi_handler_initonly, that tags the struct as
__initdata to resolve the mismatch. This #define should only be
used in rare situations where the register/unregister is called
during init of the kernel.
Big thanks to Jan Beulich for decoding this for me as I didn't
have a clue what was going on.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1338991542-23000-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Cc: stable@vger.kernel.org
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description]
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.
But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1SccoO-0002Lh-Cb@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Robin found this regression:
| I just tried to boot an 8TB system. It fails very early in boot with:
| Kernel panic - not syncing: Cannot find space for the kernel page tables
git bisect commit 722bc6b167.
A git revert of that commit does boot past that point on the 8TB
configuration.
That commit will add up extra pages for all memory range even
above 4g.
Try to limit that extra page count adding to first entry only.
Bisected-by: Robin Holt <holt@sgi.com>
Tested-by: Robin Holt <holt@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/CAE9FiQUj3wyzQxtq9yzBNc9u220p8JZ1FYHG7t%3DMOzJ%3D9BZMYA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
retention idle works again.
Also included are few other PM wake-up related fixes, and removal of
dead cpu detection code.
The other fixes are trivial build and randconfig related fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Aa3m
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
The biggest fix here is the long pending patch mux UART pins so PM
retention idle works again.
Also included are few other PM wake-up related fixes, and removal of
dead cpu detection code.
The other fixes are trivial build and randconfig related fixes.
* tag 'omap-fixes-for-v3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: OMAP: SoC detection: remove unused cpu_is macros
ARM: OMAP3: clock data: cleanup AM3[35]x SoC detection
arm: omap3: am35x: Don't mark missing features as present
ARM: OMAP3: PM: fix shared PRCM interrupts: leave disabled at boot
ARM: OMAP2+: INTC: fix suspend abort, set IRQCHIP_SKIP_SET_WAKE
Linux runs in non-secure mode on highbank, so we need secure monitor calls
to enable and disable the PL310. Rather than invent new smc calls, the same
calling convention used by OMAP is used here.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts 68568add2c ("powerpc/time: Remove unnecessary sanity check
of decrementer expiration"). We do need to check whether we have reached
the expiration time of the next event, because we sometimes get an early
decrementer interrupt, most notably when we set the decrementer to 1 in
arch_irq_work_raise(). The effect of not having the sanity check is that
if timer_interrupt() gets called early, we leave the decrementer set to
its maximum value, which means we then don't get any more decrementer
interrupts for about 4 seconds (or longer, depending on timebase
frequency). I saw these pauses as a consequence of getting a stray
hypervisor decrementer interrupt left over from exiting a KVM guest.
This isn't quite a straight revert because of changes to the surrounding
code, but it restores the same algorithm as was previously used.
Cc: stable@vger.kernel.org
Acked-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'imx/fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
ARM: mx31_3ds: Fix build due to missing IMX_HAVE_PLATFORM_IMX_SSI
* 'imx/clk-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
The statically defined I/O memory regions for the i.MX21 on chip
peripherals and the on board I/O peripherals of the i.MX21ADS board
overlap. This results in a kernel crash during startup. This is fixed
by reducing the memory range for the on board I/O peripherals to the
actually required range.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
* 'imx/fixes-for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tXwW
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-common-fixes' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer: "Some fixes for the fresh i.MX common clock support"
Resolved trivial conflict in arch/arm/plat-mxc/include/mach/common.h.
* tag 'imx-clk-common-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx6q: prepare and enable init on clks directly instead of clk_get first
ARM i.MX: remove now unnecessary argument from mxc_timer_init
ARM: i.MX: change timer clock from ipg to perclk
ARM i.MX5: fix gpt peripheral clock path
Signed-off-by: Olof Johansson <olof@lixom.net>
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This is a set of three bug fixes for minor build breakages that got introduced
just before 3.5-rc1 was released.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP0ENjAAoJEDeqqVYsXL0MyjIIAIWuQZ4YYSB1b06U8Bd82vLL
ES9hJ7ZfgKO/2bgEWRR3HgUM4kqWt31TbqaVmwbZKy+Z7XRTCtpCeOEIraS9VrI+
tTDyUmhEwaxDAj9XisbVZwPxCI6f06Pry0K1JJn505MaVzQ8F4/fyjhLuwIoWX+Z
Lqkl4DW4hQwqPNuBUT8paGLAenA5S9FHjhugqSiNCBKRhz7/vfHyOUHzZb8mMs2a
8A5ZjJA6rLiCLauM3JPndq5e+GxHyN04A6o75b721I440yvBqxHsnCM8n59N8LRd
nBgdrlorsOav/2l+BG5qrnh4Uavmniax5sAk4byqq4F6etHFCeem9lqhKFPcw6k=
=xh6K
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of three bug fixes for minor build breakages that got
introduced just before 3.5-rc1 was released."
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix code to find libgcc
[PARISC] fix compile break in use of lib/strncopy_from_user.c
[PARISC] fix missing TAINT_WARN problem
Pull tile fixes from Chris Metcalf:
"These two minor bug fixes fix build failures from some changes that
were merged in during the 3.5 merge window."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: add #include to unbreak build after generic init_task conversion
tile: remove cpu_idle_on_new_stack
There is a system hang issue on imx6q which can easily be seen with
running a cpu hotplug stress testing (hotplug secondary cores from
user space via sysfs interface for thousands iterations).
It turns out that the issue is caused by coherency of the cpu that
is being shut down. When shutting down a cpu, we need to have the
cpu exit coherency to prevent it from receiving cache, TLB, or BTB
maintenance operations broadcast by other CPUs in the cluster.
Copy cpu_enter_lowpower() and cpu_leave_lowpower() from mach-vexpress
to have coherency properly handled in platform_cpu_die(), thus fix
the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@kernel.org
Some code was moved from init_task.c to setup.c but the appropriate
header needed to be moved as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This routine isn't used unless CONFIG_HOMECACHE is enabled, which
isn't even available as a public configuration option yet.
Since it no longer links correctly in 3.4, just remove it for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Without this patch, applications with two different stack
regions (eg: native stack vs JIT stack) get truncated
callchains even when RBP chaining is present. GDB shows proper
stack traces and the frame pointer chaining is intact.
This patch disables the (fp < RSP) check, hoping that other checks
in the code save the day for us. In our limited testing, this
didn't seem to break anything.
In the long term, we could potentially have userspace advise
the kernel on the range of valid stack addresses, so we don't
spend a lot of time unwinding from bogus addresses.
Signed-off-by: Arun Sharma <asharma@fb.com>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-perf-users@vger.kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334961696-19580-2-git-send-email-asharma@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Afaict there's no need to (incompletely) iterate the
MEM_UOPS_RETIRED.* umask state.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement rudimentary IVB perf support. The SDM states its identical
to SNB with exception of the exact event tables, but a quick look
suggests they're similar enough.
Also mark SNB-EP as broken for now.
Requested-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that there's finally a chip with working PEBS (IvyBridge), we can
enable the hardware and implement cycles:p for SNB/IVB.
Cc: Stephane Eranian <eranian@google.com>
Requested-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Zheng Yan reported that event group validation can wreck event state
when Intel extra_reg allocation changes event state.
Validation shouldn't change any persistent state. Cloning events in
validate_{event,group}() isn't really pretty either, so add a few
special cases to avoid modifying the event state.
The code is restructured to minimize the special case impact.
Reported-by: Zheng Yan <zheng.z.yan@linux.intel.com>
Acked-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338903031.28282.175.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 316ad24830 ("sched/x86: Rewrite set_cpu_sibling_map()")
broke the booted_cores accounting.
The problem is that the booted_cores accounting needs all the
sibling links set up. So restore the second loop and add a comment as
to why its needed.
On qemu booted with -smp sockets=1,cores=2,threads=2;
Before:
$ grep cores /proc/cpuinfo
cpu cores : 2
cpu cores : 1
cpu cores : 4
cpu cores : 3
With the patch:
$ grep cores /proc/cpuinfo
cpu cores : 2
cpu cores : 2
cpu cores : 2
cpu cores : 2
Reported-by: Prarit Bhargava <prarit@redhat.com>
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120531073738.GH7511@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In current Linux, percpu variable `vector_irq' is not cleared on
offlined cpus while disabling devices' irqs. If the cpu that has
the disabled irqs in vector_irq is hotplugged,
__setup_vector_irq() hits invalid irq vector and may crash.
This bug can be reproduced as following;
# echo 0 > /sys/devices/system/cpu/cpu7/online
# modprobe -r some_driver_using_interrupts # vector_irq@cpu7 uncleared
# echo 1 > /sys/devices/system/cpu/cpu7/online # kernel may crash
This patch fixes this bug by clearing vector_irq in
__clear_irq_vector() even if the cpu is offlined.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: ltc-kernel@ml.yrl.intra.hitachi.co.jp
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/4FC340BE.7080101@hitachi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When rebooting our 24 CPU Westmere servers with 3.4-rc6, we
always see this warning msg:
Restarting system.
machine restart
------------[ cut here ]------------
WARNING: at arch/x86/kernel/smp.c:125
native_smp_send_reschedule+0x74/0xa7() Hardware name: X8DTN
Modules linked in: igb [last unloaded: scsi_wait_scan]
Pid: 1, comm: systemd-shutdow Not tainted 3.4.0-rc6+ #22
Call Trace:
<IRQ> [<ffffffff8102a41f>] warn_slowpath_common+0x7e/0x96
[<ffffffff8102a44c>] warn_slowpath_null+0x15/0x17
[<ffffffff81018cf7>] native_smp_send_reschedule+0x74/0xa7
[<ffffffff810561c1>] trigger_load_balance+0x279/0x2a6
[<ffffffff81050112>] scheduler_tick+0xe0/0xe9
[<ffffffff81036768>] update_process_times+0x60/0x70
[<ffffffff81062f2f>] tick_sched_timer+0x68/0x92
[<ffffffff81046e33>] __run_hrtimer+0xb3/0x13c
[<ffffffff81062ec7>] ? tick_nohz_handler+0xd0/0xd0
[<ffffffff810474f2>] hrtimer_interrupt+0xdb/0x198
[<ffffffff81019a35>] smp_apic_timer_interrupt+0x81/0x94
[<ffffffff81655187>] apic_timer_interrupt+0x67/0x70
<EOI> [<ffffffff8101a3c4>] ? default_send_IPI_mask_allbutself_phys+0xb4/0xc4
[<ffffffff8101c680>] physflat_send_IPI_allbutself+0x12/0x14
[<ffffffff81018db4>] native_nmi_stop_other_cpus+0x8a/0xd6
[<ffffffff810188ba>] native_machine_shutdown+0x50/0x67
[<ffffffff81018926>] machine_shutdown+0xa/0xc
[<ffffffff8101897e>] native_machine_restart+0x20/0x32
[<ffffffff810189b0>] machine_restart+0xa/0xc
[<ffffffff8103b196>] kernel_restart+0x47/0x4c
[<ffffffff8103b2e6>] sys_reboot+0x13e/0x17c
[<ffffffff8164e436>] ? _raw_spin_unlock_bh+0x10/0x12
[<ffffffff810fcac9>] ? bdi_queue_work+0xcf/0xd8
[<ffffffff810fe82f>] ? __bdi_start_writeback+0xae/0xb7
[<ffffffff810e0d64>] ? iterate_supers+0xa3/0xb7
[<ffffffff816547a2>] system_call_fastpath+0x16/0x1b
---[ end trace 320af5cb1cb60c5b ]---
The root cause seems to be the
default_send_IPI_mask_allbutself_phys() takes quite some time (I
measured it could be several ms) to complete sending NMIs to all
the other 23 CPUs, and for HZ=250/1000 system, the time is long
enough for a timer interrupt to happen, which will in turn
trigger to kick load balance to a stopped CPU and cause this
warning in native_smp_send_reschedule().
So disabling the local irq before stop_other_cpu() can fix this
problem (tested 25 times reboot ok), and it is fine as there
should be nobody caring the timer interrupt in such reboot
stage.
The latest 3.4 kernel slightly changes this behavior by sending
REBOOT_VECTOR first and only send NMI_VECTOR if the REBOOT_VCTOR
fails, and this patch is still needed to prevent the problem.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120530231541.4c13433a@feng-i7
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The allmodconfig hits:
WARNING: vmlinux.o(.text+0x6553d): Section mismatch in
reference from the function intel_scu_devices_create() to the
function .devinit.text: spi_register_board_info()
[...]
This patch marks intel_scu_devices_create() as devinit because
it only calls a devinit function, spi_register_board_info().
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: http://lkml.kernel.org/r/20120531212025.GA8519@breakpoint.cc
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When hot-adding a CPU, the system outputs following messages
since node_to_cpumask_map[2] was not allocated memory.
Booting Node 2 Processor 32 APIC 0xc0
node_to_cpumask_map[2] NULL
Pid: 0, comm: swapper/32 Tainted: G A 3.3.5-acd #21
Call Trace:
[<ffffffff81048845>] debug_cpumask_set_cpu+0x155/0x160
[<ffffffff8105e28a>] ? add_timer_on+0xaa/0x120
[<ffffffff8150665f>] numa_add_cpu+0x1e/0x22
[<ffffffff815020bb>] identify_cpu+0x1df/0x1e4
[<ffffffff815020d6>] identify_econdary_cpu+0x16/0x1d
[<ffffffff81504614>] smp_store_cpu_info+0x3c/0x3e
[<ffffffff81505263>] smp_callin+0x139/0x1be
[<ffffffff815052fb>] start_secondary+0x13/0xeb
The reason is that the bit of node 2 was not set at
numa_nodes_parsed. numa_nodes_parsed is set by only
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init. Thus even if hot-added memory
which is same PXM as hot-added CPU is written in ACPI SRAT
Table, if the hot-added CPU is not written in ACPI SRAT table,
numa_nodes_parsed is not set.
But according to ACPI Spec Rev 5.0, it says about ACPI SRAT
table as follows: This optional table provides information that
allows OSPM to associate processors and memory ranges, including
ranges of memory provided by hot-added memory devices, with
system localities / proximity domains and clock domains.
It means that ACPI SRAT table only provides information for CPUs
present at boot time and for memory including hot-added memory.
So hot-added memory is written in ACPI SRAT table, but hot-added
CPU is not written in it. Thus numa_nodes_parsed should be set
by not only acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init but also
acpi_numa_memory_affinity_init for the case.
Additionally, if system has cpuless memory node,
acpi_numa_processor_affinity_init /
acpi_numa_x2apic_affinity_init cannot set numa_nodes_parseds
since these functions cannot find cpu description for the node.
In this case, numa_nodes_parsed needs to be set by
acpi_numa_memory_affinity_init.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: liuj97@gmail.com
Cc: kosaki.motohiro@gmail.com
Link: http://lkml.kernel.org/r/4FCC2098.4030007@jp.fujitsu.com
[ merged it ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit 82f7af09 ("x86/mce: Cleanup timer mess) dropped the
initialization of the per cpu timer interval. Duh :(
Restore the previous behaviour.
Reported-by: Chen Gong <gong.chen@linux.intel.com>
Cc: bp@amd64.org
Cc: tony.luck@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 7f28427b (ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2)
moved DSP platform init code, but failed to include memblock.h causing:
arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/mach-omap2/dsp.c:58: error: implicit declaration of function 'arm_memblock_steal'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we will get:
arch/arm/mach-omap2/omap_l3_smx.c: In function ‘omap3_l3_block_irq’:
arch/arm/mach-omap2/omap_l3_smx.c:156: warning: unused variable ‘address’
arch/arm/mach-omap2/omap_l3_smx.c:155: warning: unused variable ‘multi’
arch/arm/mach-omap2/omap_l3_smx.c:154: warning: unused variable ‘initid’
arch/arm/mach-omap2/omap_l3_smx.c:153: warning: unused variable ‘code’
arch/arm/mach-omap2/omap_l3_smx.c: At top level:
arch/arm/mach-omap2/omap_l3_smx.c:68: warning: ‘omap3_l3_code_string’ defined but not used
arch/arm/mach-omap2/omap_l3_smx.c:90: warning: ‘omap3_l3_initiator_string’ defined but not used
Fix it by always showing the L3 error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_MMC_OMAP is not set and CONFIG_MMC_OMAP_HS is set,
we can get error: redefinition of `omap242x_init_mmc' error.
Fix it by removing MMC_OMAP_HS from MMC_OMAP ifdefs as they do
not depend on each other.
While at it, also prettify the formatting a bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the x86 instruction decoder to decode bsr/bsf/jmpe with
operand-size prefix (66h). This fixes the test case failure
reported by Linus, attached below.
bsf/bsr/jmpe have a special encoding. Opcode map in
Intel Software Developers Manual vol2 says they have
TZCNT/LZCNT variants if it has F3h prefix. However, there
is no information if it has other 66h or F2h prefixes.
Current instruction decoder supposes that those are
bad instructions, but it actually accepts at least
operand-size prefixes.
H. Peter Anvin further explains:
" TZCNT/LZCNT are F3 + BSF/BSR exactly because the F2 and
F3 prefixes have historically been no-ops with most instructions.
This allows software to unconditionally use the prefixed versions
and get TZCNT/LZCNT on the processors that have them if they don't
care about the difference. "
This fixes errors reported by test_get_len:
Warning: arch/x86/tools/test_get_len found difference at <em_bsf>:ffffffff81036d87
Warning: ffffffff81036de5: 66 0f bc c2 bsf %dx,%ax
Warning: objdump says 4 bytes, but insn_get_length() says 3
Warning: arch/x86/tools/test_get_len found difference at <em_bsr>:ffffffff81036ea6
Warning: ffffffff81036f04: 66 0f bd c2 bsr %dx,%ax
Warning: objdump says 4 bytes, but insn_get_length() says 3
Warning: decoded and checked 13298882 instructions with 2 warnings
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <yrl.pp-manager.tt@hitachi.com>
Link: http://lkml.kernel.org/r/20120604150911.22338.43296.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull arm CMA fix from Marek Szyprowski:
"This removes the ARMv6+ CMA dependency and lets one use old, well-
tested dma-mapping implementation also on ARMv6+ systems without the
need to use EXPERIMENTAL stuff."
Russell King complained (rightly) about the experimental feature being
forced on by the ARM config.
Here CMA is "continuous memory allocator", not "cross-memory attach".
We really neet to stop using insane TLA's for things that aren't big
industry standards.
* 'fixes-for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: remove unconditional dependency on CMA
In commit 82f7af09 (x86/mce: Cleanup timer mess), Thomas just forgot
the "/ 2" there while cleaning up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Remove NULL assignment of dattr_cur
sched: Remove the last NULL entry from sched_feat_names
sched: Make sched_feat_names const
sched/rt: Fix SCHED_RR across cgroups
sched: Move nr_cpus_allowed out of 'struct sched_rt_entity'
sched: Make sure to not re-read variables after validation
sched: Fix SD_OVERLAP
sched: Don't try allocating memory from offline nodes
sched/nohz: Fix rq->cpu_load calculations some more
sched/x86: Use cpu_llc_shared_mask(cpu) for coregroup_mask
The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.
One such crash was reported by John Stultz <johnstul@us.ibm.com>:
[ 18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[ 18.765319] pgd = ea6b8000
[ 18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[ 18.774749] Internal error: Oops: 17 [#1] SMP ARM
[ 18.779663] Modules linked in:
[ 18.782836] CPU: 0 Not tainted (3.5.0-rc1-dirty #456)
[ 18.788482] PC is at _od_resume_noirq+0x1c/0x78
[ 18.793212] LR is at _od_resume_noirq+0x6c/0x78
[ 18.797943] pc : [<c00307ec>] lr : [<c003083c>] psr: 20000113
[ 18.797943] sp : ec3abe80 ip : ec3abdb8 fp : 00000006
[ 18.809936] r10: ec1148b8 r9 : c08a48f0 r8 : c00307d0
[ 18.815368] r7 : 00000000 r6 : 00000000 r5 : ec114800 r4 :
ec114808
[ 18.822174] r3 : 00000000 r2 : 00000000 r1 : ec154fe8 r0 :
00000006
[ 18.829010] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 18.836456] Control: 10c5387d Table: aa6b804a DAC: 00000015
[ 18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[ 18.848358] Stack: (0xec3abe80 to 0xec3ac000)
DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.htmlhttp://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some GPIOs in Visstrim M10 are used without being registered.
This leads to USB and video malfunctions. This patch registers
those GPIOs to solve the issue.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sam broke this with
commit 1f2bfbd00e
Author: Sam Ravnborg <sam@ravnborg.org>
Date: Sat May 5 10:18:41 2012 +0200
kbuild: link of vmlinux moved to a script
But we should be deriving the location of libgcc in the same way as all
the other archs, so fix by adding a LIBGCC variable which is evaluated
in the makefile
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus broke us with
commit 36126f8f2e
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sat May 26 10:43:17 2012 -0700
word-at-a-time: make the interfaces truly generic
By moving functions defined in strncopy_from_user.c into the asm-geneic
version word-at-a-time.h. Spark and OpenRisc were fixed to use this, but
not parisc. Fix by adding to generic-y in asm/Kbuild
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Al viro broke us with
commit edd63a2763
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Fri Apr 27 13:42:45 2012 -0400
set_restore_sigmask() is never called without SIGPENDING (and never should be)
Although it's pretty much our fault since parisc's asm/bug.h uses
BUGWARN_TAINT but doesn't include the file that defines it. Fix that.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dell Precision M6600 is known to require PCI reboot, so add it to
the reboot blacklist in pci_reboot_dmi_table[].
https://bugzilla.kernel.org/show_bug.cgi?id=42749
cc: x86@kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull timer updates from Thomas Gleixner:
"The clocksource driver is pure hardware enablement and the skew option
is default off, well tested and non dangerous."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move skew_tick option into the HIGH_RES_TIMER section
clocksource: em_sti: Add DT support
clocksource: em_sti: Emma Mobile STI driver
clockevents: Make clockevents_config() a global symbol
tick: Add tick skew boot option
MX53_DPLL4_BASE accidently returned the base address of PLL3.
Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
in round_rate we made the assumption that we can set arbitrary
frequencies and thus returned the input rate. This is not correct,
for certain frequencies after setting a frequency with set_rate,
recalc_rate will return different values. To fix this, introduce
set_rate/recalc_rate functions which work on variables instead
of registers directly. This way we can call these in round_rate
to get the exact rate which we would get if we call set_rate
with this value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX5 PLL has two different register sets for setting the
rate. One is used for the standard case and and is used for
DVFS. Which one of them is used depends on a hardware input
of the PLL. Current implementation reads back from the hardware
which setting is used. This is bogus: If we ever want to implement
DVFS we have to program both register sets and not only the one
which happens to be used at the moment. For now, just use the
standard register set uncondionally.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer)
added support for lis3lv02d accelerometer.
The patch was still using OMAP_GPIO_IRQ which no longer exists.
Fix it by using gpio_to_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
CMA has been enabled unconditionally on all ARMv6+ systems to solve the
long standing issue of double kernel mappings for all dma coherent
buffers. This however created a dependency on CONFIG_EXPERIMENTAL for
the whole ARM architecture what should be really avoided. This patch
removes this dependency and lets one use old, well-tested dma-mapping
implementation also on ARMv6+ systems without the need to use
EXPERIMENTAL stuff.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
commit e57f93cc53 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduced by commit 6fd84c0831
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Pull arm fixes for ux500 mismerge mishap from Arnd Bergmann:
"The device tree conversion for arm/ux500 in 3.5 turns out to be
incomplete because of a mismerge done by Linus Walleij that I failed
to notice early enough and that Lee Jones as the original author of
those patches did not manage to fix during the -next cycle. While we
originally to get a much larger set of ux500 device tree enablement
patches merged, this did not happen in time.
After some discussion at Linaro Connect conference this week, Lee has
been able to do damage control and provide a series to put the broken
platform back into usable shape for both DT and non-DT based booting.
This series has not been part of linux-next and is based on top of the
current state of the upstream kernel rather than an -rc, but this is
the best we could manage given the earlier breakage."
* 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Enable probing of pinctrl through Device Tree
ARM: ux500: Add support for ab8500 regulators into the Device Tree
ARM: ux500: Provide regulator support for SMSC911x via Device Tree
ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot
ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree
ARM: ux500: Only initialise STE's UIBs on boards which support them
ARM: ux500: Disable platform setup of the ab8500 when DT is enabled
ARM: ux500: Use correct format for dynamic IRQ assignment
ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots
ARM: ux500: PRCMU related configuration and layout corrections for Device Tree
ARM: ux500: Remove DB8500 PRCMU platform registration when DT is enabled
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: New DT:ed u8500_init_devices for one-by-one device enablement
ARM: ux500: New DT:ed snowball_platform_devs for one-by-one device enablement
pinctrl-nomadik: Allow Device Tree driver probing
When I added x32 ptrace to 3.4 kernel, I also include PTRACE_ARCH_PRCTL
support for x32 GDB For ARCH_GET_FS/GS, it takes a pointer to int64. But
at user level, ARCH_GET_FS/GS takes a pointer to int32. So I have to add
x32 ptrace to glibc to handle it with a temporary int64 passed to kernel and
copy it back to GDB as int32. Roland suggested that PTRACE_ARCH_PRCTL
is obsolete and x32 GDB should use fs_base and gs_base fields of
user_regs_struct instead.
Accordingly, remove PTRACE_ARCH_PRCTL completely from the x32 code to
avoid possible memory overrun when pointer to int32 is passed to
kernel.
Link: http://lkml.kernel.org/r/CAMe9rOpDzHfS7NH7m1vmD9QRw8SSj4Sc%2BaNOgcWm_WJME2eRsQ@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org> v3.4
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
If we end up calling do_notify_resume() with !user_mode(refs), it
does nothing (do_signal() explicitly bails out and we can't get there
with TIF_NOTIFY_RESUME in such situations). Then we jump to
resume_userspace_sig, which rechecks the same thing and bails out
to resume_kernel, thus breaking the loop.
It's easier and cheaper to check *before* calling do_notify_resume()
and bail out to resume_kernel immediately. And kill the check in
do_signal()...
Note that on amd64 we can't get there with !user_mode() at all - asm
glue takes care of that.
Acked-and-reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Optimise the system call exit path in entry.S by packing some instructions.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Shrink TIF_WORK_MASK so that it will fit in the 12-bit signed immediate
operand field of an ANDI instruction.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Move the test for kernel mode processing from do_signal() into entry.S to also
prevent system call exit tracing and userspace resumption notification handling
happening when returning from kernel exceptions.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since we can't expect every user to read the EFI boot stub code it
seems prudent to have a couple of paragraphs explaining what it is and
how it works.
The "initrd=" option in particular is tricky because it only
understands absolute EFI-style paths (backslashes as directory
separators), and until now this hasn't been documented anywhere. This
has tripped up a couple of users.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-4-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need a way of printing useful messages to the user, for example
when we fail to open an initrd file, instead of just hanging the
machine without giving the user any indication of what went wrong. So
sprinkle some error messages throughout the EFI boot stub code to make
it easier for users to diagnose/report problems.
Reported-by: Keshav P R <the.ridikulus.rat@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-3-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The loop at the 'close_handles' label in handle_ramdisks() should be
using 'i', which represents the number of initrd files that were
successfully opened, not 'nr_initrds' which is the number of initrd=
arguments passed on the command line.
Currently, if we execute the loop to close all file handles and we
failed to open any initrds we'll try to call the close function on a
garbage pointer, causing the machine to hang.
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-2-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When both DYNAMIC_FTRACE and LOCKDEP are set, the TRACE_IRQS_ON/OFF
will call into the lockdep code. The lockdep code can call lots of
functions that may be traced by ftrace. When ftrace is updating its
code and hits a breakpoint, the breakpoint handler will call into
lockdep. If lockdep happens to call a function that also has a breakpoint
attached, it will jump back into the breakpoint handler resetting
the stack to the debug stack and corrupt the contents currently on
that stack.
The 'do_sym' call that calls do_int3() is protected by modifying the
IST table to point to a different location if another breakpoint is
hit. But the TRACE_IRQS_OFF/ON are outside that protection, and if
a breakpoint is hit from those, the stack will get corrupted, and
the kernel will crash:
[ 1013.243754] BUG: unable to handle kernel NULL pointer dereference at 0000000000000002
[ 1013.272665] IP: [<ffff880145cc0000>] 0xffff880145cbffff
[ 1013.285186] PGD 1401b2067 PUD 14324c067 PMD 0
[ 1013.298832] Oops: 0010 [#1] PREEMPT SMP
[ 1013.310600] CPU 2
[ 1013.317904] Modules linked in: ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables crc32c_intel ghash_clmulni_intel microcode usb_debug serio_raw pcspkr iTCO_wdt i2c_i801 iTCO_vendor_support e1000e nfsd nfs_acl auth_rpcgss lockd sunrpc i915 video i2c_algo_bit drm_kms_helper drm i2c_core [last unloaded: scsi_wait_scan]
[ 1013.401848]
[ 1013.407399] Pid: 112, comm: kworker/2:1 Not tainted 3.4.0+ #30
[ 1013.437943] RIP: 8eb8:[<ffff88014630a000>] [<ffff88014630a000>] 0xffff880146309fff
[ 1013.459871] RSP: ffffffff8165e919:ffff88014780f408 EFLAGS: 00010046
[ 1013.477909] RAX: 0000000000000001 RBX: ffffffff81104020 RCX: 0000000000000000
[ 1013.499458] RDX: ffff880148008ea8 RSI: ffffffff8131ef40 RDI: ffffffff82203b20
[ 1013.521612] RBP: ffffffff81005751 R08: 0000000000000000 R09: 0000000000000000
[ 1013.543121] R10: ffffffff82cdc318 R11: 0000000000000000 R12: ffff880145cc0000
[ 1013.564614] R13: ffff880148008eb8 R14: 0000000000000002 R15: ffff88014780cb40
[ 1013.586108] FS: 0000000000000000(0000) GS:ffff880148000000(0000) knlGS:0000000000000000
[ 1013.609458] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1013.627420] CR2: 0000000000000002 CR3: 0000000141f10000 CR4: 00000000001407e0
[ 1013.649051] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1013.670724] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 1013.692376] Process kworker/2:1 (pid: 112, threadinfo ffff88013fe0e000, task ffff88014020a6a0)
[ 1013.717028] Stack:
[ 1013.724131] ffff88014780f570 ffff880145cc0000 0000400000004000 0000000000000000
[ 1013.745918] cccccccccccccccc ffff88014780cca8 ffffffff811072bb ffffffff81651627
[ 1013.767870] ffffffff8118f8a7 ffffffff811072bb ffffffff81f2b6c5 ffffffff81f11bdb
[ 1013.790021] Call Trace:
[ 1013.800701] Code: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a <e7> d7 64 81 ff ff ff ff 01 00 00 00 00 00 00 00 65 d9 64 81 ff
[ 1013.861443] RIP [<ffff88014630a000>] 0xffff880146309fff
[ 1013.884466] RSP <ffff88014780f408>
[ 1013.901507] CR2: 0000000000000002
The solution was to reuse the NMI functions that change the IDT table to make the debug
stack keep its current stack (in kernel mode) when hitting a breakpoint:
call debug_stack_set_zero
TRACE_IRQS_ON
call debug_stack_reset
If the TRACE_IRQS_ON happens to hit a breakpoint then it will keep the current stack
and not crash the box.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the NMI handler runs, it checks if it preempted a debug handler
and if that handler is using the debug stack. If it is, it changes the
IDT table not to update the stack, otherwise it will reset the debug
stack and corrupt the debug handler it preempted.
Now that ftrace uses breakpoints to change functions from nops to
callers, many more places may hit a breakpoint. Unfortunately this
includes some of the calls that lockdep performs. Which causes issues
with the debug stack. It too needs to change the debug stack before
tracing (if called from the debug handler).
Allow the debug_stack_set_zero() and debug_stack_reset() to be nested
so that the debug handlers can take advantage of them too.
[ Used this_cpu_*() over __get_cpu_var() as suggested by H. Peter Anvin ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When an NMI goes off and it sees that it preempted the debug stack,
to keep the debug stack safe, it changes the IDT to point to one that
does not modify the stack on breakpoint (to allow breakpoints in NMIs).
But the variable that gets set to know to undo it on exit never gets
cleared on exit. Thus every NMI will reset it on exit the first time
it is done even if it does not need to be reset.
[ Added H. Peter Anvin's suggestion to use this_cpu_read/write ]
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On boot up and module load, it is fine to modify the code directly,
without the use of breakpoints. This is because boot up modification
is done before SMP is initialized, thus the modification is serial,
and module load is done before the module executes.
But after that we must use a SMP safe method to modify running code.
Otherwise, if we are running the function tracer and update its
function (by starting off the stack tracer, or perf tracing)
the change of the function called by the ftrace trampoline is done
directly. If this is being executed on another CPU, that CPU may
take a GPF and crash the kernel.
The breakpoint method is used to change the nops at all the functions, but
the change of the ftrace callback handler itself was still using a
direct modification. If tracing was enabled and the function callback
was changed then another CPU could fault if it was currently calling
the original callback. This modification must use the breakpoint method
too.
Note, the direct method is still used for boot up and module load.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the function tracer starts modifying the code via breakpoints
it sets a variable (modifying_ftrace_code) to inform the breakpoint
handler to call the ftrace int3 code.
But there's no synchronization between setting this code and the
handler, thus it is possible for the handler to be called on another
CPU before it sees the variable. This will cause a kernel crash as
the int3 handler will not know what to do with it.
I originally added smp_mb()'s to force the visibility of the variable
but H. Peter Anvin suggested that I just make it atomic.
[ Added comments as suggested by Peter Zijlstra ]
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Merge misc patches from Andrew Morton:
- the "misc" tree - stuff from all over the map
- checkpatch updates
- fatfs
- kmod changes
- procfs
- cpumask
- UML
- kexec
- mqueue
- rapidio
- pidns
- some checkpoint-restore feature work. Reluctantly. Most of it
delayed a release. I'm still rather worried that we don't have a
clear roadmap to completion for this work.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (78 patches)
kconfig: update compression algorithm info
c/r: prctl: add ability to set new mm_struct::exe_file
c/r: prctl: extend PR_SET_MM to set up more mm_struct entries
c/r: procfs: add arg_start/end, env_start/end and exit_code members to /proc/$pid/stat
syscalls, x86: add __NR_kcmp syscall
fs, proc: introduce /proc/<pid>/task/<tid>/children entry
sysctl: make kernel.ns_last_pid control dependent on CHECKPOINT_RESTORE
aio/vfs: cleanup of rw_copy_check_uvector() and compat_rw_copy_check_uvector()
eventfd: change int to __u64 in eventfd_signal()
fs/nls: add Apple NLS
pidns: make killed children autoreap
pidns: use task_active_pid_ns in do_notify_parent
rapidio/tsi721: add DMA engine support
rapidio: add DMA engine support for RIO data transfers
ipc/mqueue: add rbtree node caching support
tools/selftests: add mq_perf_tests
ipc/mqueue: strengthen checks on mqueue creation
ipc/mqueue: correct mq_attr_ok test
ipc/mqueue: improve performance of send/recv
selftests: add mq_open_tests
...
While doing the checkpoint-restore in the user space one need to determine
whether various kernel objects (like mm_struct-s of file_struct-s) are
shared between tasks and restore this state.
The 2nd step can be solved by using appropriate CLONE_ flags and the
unshare syscall, while there's currently no ways for solving the 1st one.
One of the ways for checking whether two tasks share e.g. mm_struct is to
provide some mm_struct ID of a task to its proc file, but showing such
info considered to be not that good for security reasons.
Thus after some debates we end up in conclusion that using that named
'comparison' syscall might be the best candidate. So here is it --
__NR_kcmp.
It takes up to 5 arguments - the pids of the two tasks (which
characteristics should be compared), the comparison type and (in case of
comparison of files) two file descriptors.
Lookups for pids are done in the caller's PID namespace only.
At moment only x86 is supported and tested.
[akpm@linux-foundation.org: fix up selftests, warnings]
[akpm@linux-foundation.org: include errno.h]
[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: Michal Marek <mmarek@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kill_off_processes() might miss a valid process, this is because checking
for process->mm is not enough. Process' main thread may exit or detach
its mm via use_mm(), but other threads may still have a valid mm.
To catch this we use find_lock_task_mm(), which walks up all threads and
returns an appropriate task (with task lock held).
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking for task->mm is dangerous as ->mm might disappear (exit_mm()
assigns NULL under task_lock(), so tasklist lock is not enough).
We can't use get_task_mm()/mmput() pair as mmput() might sleep, so let's
take the task lock while we care about its mm.
Note that we should also use find_lock_task_mm() to check all process'
threads for a valid mm, but for uml we'll do it in a separate patch.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Traversing the tasks requires holding tasklist_lock, otherwise it is
unsafe.
p.s. However, I'm not sure that calling os_kill_ptraced_process() in the
atomic context is correct. It seem to work, but please take a closer
look.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov found an interesting deadlock possibility:
> sysrq_showregs_othercpus() does smp_call_function(showacpu)
> and showacpu() show_stack()->decode_address(). Now suppose that IPI
> interrupts the task holding read_lock(tasklist).
To fix this, blackfin should not grab the write_ variant of the
tasklist lock, read_ one is enough.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes two problems:
1. Working with task->mm w/o getting mm or grabing the task lock is
dangerous as ->mm might disappear (exit_mm() assigns NULL under
task_lock(), so tasklist lock is not enough).
We can't use get_task_mm()/mmput() pair as mmput() might sleep,
so we have to take the task lock while handle its mm.
2. Checking for process->mm is not enough because process' main
thread may exit or detach its mm via use_mm(), but other threads
may still have a valid mm.
To catch this we use find_lock_task_mm(), which walks up all
threads and returns an appropriate task (with task lock held).
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking for process->mm is not enough because process' main thread may
exit or detach its mm via use_mm(), but other threads may still have a
valid mm.
To fix this we would need to use find_lock_task_mm(), which would walk up
all threads and returns an appropriate task (with task lock held).
clear_tasks_mm_cpumask() has the issue fixed, so let's use it.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current CPU hotplug code has some task->mm handling issues:
1. Working with task->mm w/o getting mm or grabing the task lock is
dangerous as ->mm might disappear (exit_mm() assigns NULL under
task_lock(), so tasklist lock is not enough).
We can't use get_task_mm()/mmput() pair as mmput() might sleep,
so we must take the task lock while handle its mm.
2. Checking for process->mm is not enough because process' main
thread may exit or detach its mm via use_mm(), but other threads
may still have a valid mm.
To fix this we would need to use find_lock_task_mm(), which would
walk up all threads and returns an appropriate task (with task
lock held).
clear_tasks_mm_cpumask() has all the issues fixed, so let's use it.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking for process->mm is not enough because process' main thread may
exit or detach its mm via use_mm(), but other threads may still have a
valid mm.
To fix this we would need to use find_lock_task_mm(), which would walk up
all threads and returns an appropriate task (with task lock held).
clear_tasks_mm_cpumask() has this issue fixed, so let's use it.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d065bd810b ("mm: retry page fault when blocking on disk
transfer") and commit 37b23e0525 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to um.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Nomadik GPIO controller now relies on Nomadik pinctrl, however
the pinctrl driver is not currently started by any ux500 platform.
This is requred or GPIOs do not work at all.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU regulators would be processed
when DT is enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we inform Device Tree of which regulators are provided by the db8500-
prcmu. This way we can reference some of their consumers directly from the
Device Tree e.g. SMSC911x Ethernet chip.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ST-Ericsson uses User Interface Boards to extend functionality of
some of their development boards. However, these aren't compatible
with all the supported boards found in Mainline (Snowball for
instance). This patch ensures that the UIBs are only probed on
boards which can actually support them. This in turn saves lots of
unnecessary error messages normally found in Snowball's boot log.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The final piece of the ab8500 puzzle. Here we prevent any of the ab8500-*
drivers from being registered from platform code when Device Tree is
enabled, as we expect DT do probe each of these individually. We also
provide the relevant compatible strings, so that DT knows which nodes
it needs to pay attention to during population.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The patch to disable SMSC911x registration was applied twice in the upstream
kernel by mistake. Git interpreted this as 'take the same entry from a
similar struct' which was close by. This was the wrong thing to do. This patch
rectifies this error and re-enables SMSC911x registration when Device Tree is
not enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now the DB8500 has Device Tree support it will be probed when the DT
is parsed, rendering the requirement for platform registration void.
This patch removes DB8500 PRCMU platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove
<hw_component>_add_<device> calls one at at time, as and when particular
devices are DT enabled. This patch provides a temporary solution. Once
the new *of_init_devices function has been fully unpopulated it will be
removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove snowball_<device>*
platform_data segments one at at time, as and when particular devices are
DT enabled. This patch provides a temporary solution. Once this new struct
is empty it will be removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull two small kvm fixes from Avi Kivity:
"A build fix for non-kvm archs and a transparent hugepage refcount
bugfix on hosts with 4M pages."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Export asm-generic/kvm_para.h
KVM: MMU: fix huge page adapted on non-PAE host
Pull s390 patches from Heiko Carstens:
"A couple of s390 patches for the 3.5 merge window. Just a collection
of bug fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uaccess: fix access_ok compile warnings
s390/cmpxchg: select HAVE_CMPXCHG_LOCAL option
s390/cmpxchg: fix sign extension bugs
s390/cmpxchg: fix 1 and 2 byte memory accesses
s390/cmpxchg: fix compile warnings specific to s390
s390/cmpxchg: add missing memory barrier to cmpxchg64
s390/cpu: remove cpu "capabilities" sysfs attribute
s390/kernel: Fix smp_call_ipl_cpu() for offline CPUs
s390/kernel: Introduce memcpy_absolute() function
s390/headers: replace __s390x__ with CONFIG_64BIT where possible
s390/headers: remove #ifdef __KERNEL__ from not exported headers
s390/irq: split irq stats for cpu-measurement alert facilities
s390/kexec: Move early_pgm_check_handler() to text section
s390/kdump: Use real mode for PSW restart and kexec
s390/kdump: Account /sys/kernel/kexec_crash_size changes in OS info
s390/kernel: Remove OS info init function call and diag 308 for kdump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPx039AAoJEDeqqVYsXL0Ml90H/06bB0sH5gpmJPOcMOcz2y5n
xZH4nHFGFfDUou/NFBkjBFAveBZDFy1WwsSwN44RZobmtkmqj9tfF90R0EoRsew6
kfRKJAn2iYA67WpM33v0ZpI+00VpNBt/sXP6OM08FebPu1aGriTnLm3qaOutyeC4
Q9dMHwhsMBjTcD52TlTlPBFHfOTvpB1FZmw//TwujPZ56upFw+dI1FkvzxdrG68a
ES7h8QBD8GXaM6OC8klCqq36iMjP2wJK3A+9MsERxkGLjfGEGMLC7jV3MgwvfjHY
i5w/EUheOU4SLicu7jBoC9mPHzhsWdl7OCP+E7V2CGXGysKSu4lH65ft1bMRIvg=
=ZAzL
-----END PGP SIGNATURE-----
Merge tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull misc parisc updates from James Bottomley:
"This is a couple of updates to complete our fixes and one to fix a
compile failure caused during the merge window. Additionally, we now
switch to the generic strncopy_from_user."
* tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] update parisc to use generic strncpy_from_user()
[PARISC] Fix parisc compile failure after smp: Add task_struct argument to __cpu_up()
[PARISC] fix TLB fault path on PA2.0 narrow systems
[PARISC] fix boot failure on 32-bit systems caused by branch stubs placed before .text
Pull additional x86 fixes from Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd, xen: Avoid NULL pointer paravirt references
x86, mtrr: Fix a type overflow in range_to_mtrr func
x86, realmode: Unbreak the ia64 build of drivers/acpi/sleep.c
x86/mm/pat: Improve scaling of pat_pagerange_is_ram()
x86: hpet: Fix copy-and-paste mistake in earlier change
x86/mce: Fix 32-bit build
x86/bitops: Move BIT_64() for a wider use
This branch contains a few development patches for Samsung and Versatile
Express that were submitted to arm-soc near the beginning of the merge
window. We picked them up with the agreement that they would need to
sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IA3W
-----END PGP SIGNATURE-----
Merge tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late-merged development and first fixes for arm-soc from Olof Johansson:
"This branch contains a few development patches for Samsung and
Versatile Express that were submitted to arm-soc near the beginning of
the merge window. We picked them up with the agreement that they
would need to sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx."
* tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: LPC32xx: Adjust dts files to gpio dt binding
ixp4xx: fix compilation by adding gpiolib support
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
ARM: S3C64XX: use timekeeping wrapper on cpuidle
ARM: S3C64XX: declare the states with the new api on cpuidle
ARM: S3C64XX: Hook up carrier class modules on Cragganmore
ARM: S3C64XX: Initial hookup for Bells module on Cragganmore
Pull Sparc updates from David S. Miller:
1) Remove the idiotic situation wherein Leon was a special case in all
of the TLB/cache handling code.
The worst side effect of this bogosity is that you couldn't build a
kernel with Leon support enabled (to get better build coverage), and
test boot it on a non-LEON cpu.
Leon is, in all core respects, programatically identical to the
32-bit SRMMU. Except that they put the TLB registers in a different
alternate address space location.
Through code patching (for fast paths) and run time checks, this
issue is now a thing of the past.
From Sam Ravnborg.
2) There was a mis-merge of arch/sparc/Kconfig for one of the
clockevents changes that went in, causing 32-bit sparc to start
failing to build.
I merged in your tree to get those clockevents changes (and added a
note to the merge commit) then added Stephen Rothwell's fix for the
merge error.
3) Software quad floating point emulation was not working properly on
more recent Niagara chips, because the way the situation is reported
by the cpu has changed.
Nobody noticed because gcc emits calls to software emulation
routines in glibc.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: (25 commits)
sparc: fix sparc64 build due to leon.h inclusion
sparc32: remove unused variable in head_32.S
sparc32,leon: fix leon bootup
sparc32: Export leon_dma_ops to modules.
sparc32: support leon + sun in dma_make_coherent()
sparc32,leon: always support leon in ioport
sparc32,leon: always include leon_pmc in build
sparc32: refactor cpu_idle()
sparc32: srmmu_probe now knows about leon too
sparc32: drop LEON hack for ASI_M_MMUREGS
sparc32: introduce run-time patching of srmmu access functions
sparc32: introduce support for run-time patching for all shared assembler code
sparc32,leon: fix section mismatch warning
sparc32,leon: always include leon_smp + leon_mm in build
sparc32,leon: always include leon_kernel in build
sparc32,leon: clean up leon.h
sparc32: handle leon in cpu.c
sparc32: handle leon in irq_32.c
sparc32: add support for run-time patching of leon/sun single instructions
sparc32: introduce sparc32_start_kernel called from head_32.S
...
Xen PV kernels allow access to the APERF/MPERF registers to read the
effective frequency. Access to the MSRs is however redirected to the
currently scheduled physical CPU, making consecutive read and
compares unreliable. In addition each rdmsr traps into the hypervisor.
So to avoid bogus readouts and expensive traps, disable the kernel
internal feature flag for APERF/MPERF if running under Xen.
This will
a) remove the aperfmperf flag from /proc/cpuinfo
b) not mislead the power scheduler (arch/x86/kernel/cpu/sched.c) to
use the feature to improve scheduling (by default disabled)
c) not mislead the cpufreq driver to use the MSRs
This does not cover userland programs which access the MSRs via the
device file interface, but this will be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The 32 bit variant of cbc(aes) decrypt is using instructions requiring
128 bit aligned memory locations but fails to ensure this constraint in
the code. Fix this by loading the data into intermediate registers with
load unaligned instructions.
This fixes reported general protection faults related to aesni.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43223
Reported-by: Daniel <garkein@mailueberfall.de>
Cc: stable@kernel.org [v2.6.39+]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
get_unmapped_area() returns -E... on failure, not 0. Moreover, the
wrapper around it is completely pointless.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Stub out MSR methods that aren't actually needed. This fixes a crash
as Xen Dom0 on AMD Trinity systems. A bigger patch should be added to
remove the paravirt machinery completely for the methods which
apparently have no users!
Reported-by: Andre Przywara <andre.przywara@amd.com>
Link: http://lkml.kernel.org/r/20120530222356.GA28417@andromeda.dapyr.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
* late/soc:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
Use unsigned long for dealing with jiffies not int. Rename the
callback to something sensible. Use __this_cpu_read/write for
accessing per cpu data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When boot on sun G5+ with 4T mem, see an overflow in mtrr cleanup as below.
*BAD*gran_size: 2G chunk_size: 2G num_reg: 10 lose cover RAM:
-18014398505283592M
This is because 1<<31 sign extended. Use an unsigned long constant to
fix it. Useful for mem larger than or equal to 4T.
-v2: Use 64bit constant instead of explicit type conversion as suggested
by Yinghai. Description updated too.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Link: http://lkml.kernel.org/r/4FC5A77F.6060505@oracle.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Revert usage of acpi_wakeup_address and move definition
to x86 architecture code in order to make compilation work
in ia64.
[jsakkine: tested compilation in ia64/x86-64 and added
proper commit message]
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Originally-by: H. Peter Anvin <hpa@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1338370421-27735-1-git-send-email-jarkko.sakkinen@intel.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We did not take into account that xen_released_pages would be
used outside the initial E820 parsing code. As such we would
did not subtract from xen_released_pages the count of pages
that we had populated back (instead we just did a simple
extra_pages = released - populated).
The balloon driver uses xen_released_pages to set the initial
current_pages count. If this is wrong (too low) then when a new
(higher) target is set, the balloon driver will request too many pages
from Xen."
This fixes errors such as:
(XEN) memory.c:133:d0 Could not allocate order=0 extent: id=0 memflags=0 (51 of 512)
during bootup and
free_memory : 0
where the free_memory should be 128.
Acked-by: David Vrabel <david.vrabel@citrix.com>
[v1: Per David's review made the git commit better]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since nr_cpus_allowed is used outside of sched/rt.c and wants to be
used outside of there more, move it to a more natural site.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-kr61f02y9brwzkh6x53pdptm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit commit 8e7fbcbc2 ("sched: Remove stale power aware scheduling
remnants and dysfunctional knobs") made a boo-boo with removing the
power aware scheduling muck from the x86 topology bits.
We should unconditionally use the llc_shared mask for multi-core.
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/n/tip-lsksc2kfyeveb13avh327p0d@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Function pat_pagerange_is_ram() scales poorly to large address
ranges, because it probes the resource tree for each page.
On a 2.6 GHz Opteron, this function consumes 34 ms for a 1 GB range.
It is called twice during untrack_pfn_vma(), slowing process
cleanup and handicapping the OOM killer.
This replacement consumes less than 1ms, under the same conditions.
Signed-off-by: John Dykstra <jdykstra@cray.com> on behalf of Cray Inc.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337980366.1979.6.camel@redwood
[ Small stylistic cleanups and renames ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On s390 access_ok is a macro which discards all parameters and always
returns 1. This can result in compile warnings which warn about unused
variables like this:
fs/read_write.c: In function 'rw_copy_check_uvector':
fs/read_write.c:684:16: warning: unused variable 'buf' [-Wunused-variable]
Fix this by adding a __range_ok() function which consumes all parameters
but still always returns 1.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that hopefully all cmpxchg/xchg bugs have been fixed select
HAVE_CMPXCHG_LOCAL option which uncovered a couple of bugs on s390.
The only call site which is affected seems to be within mm/vmstat.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For 1 and 2 byte operands for xchg and cmpxchg the old and new values
get or'ed into the larger 4 byte old value before the compare and swap
instruction gets executed. This is done without using the proper byte
mask before or'ing the values.
If the caller passed in negative old or new values these got sign
extended by the caller. Which in turn means that either the old value
never matches, or, even worse, unrelated bytes would be changed in memory.
Luckily there don't seem to be any callers around yet, since that would
have resulted in the specification exception fixed in an earlies patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When accessing a 1 or 2 byte memory operand we cannot use the
passed address since the compare and swap instruction only works
for 4 byte aligned memory operands.
Hence we calculate an aligned address so that compare and swap works
correctly. However we don't pass the calculated address to the inline
assembly. This results in incorrect memory accesses and in a
specification exception if used on non 4 byte aligned memory operands.
Since this didn't happen until now, there don't seem to be
too many users of cmpxchg on unaligned addresses.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cmpxchg macros and functions are a bit different than on other
architectures. In particular the macros do not store the return
value of a __cmpxchg function call in a variable before returning the
value.
This causes compile warnings that only occur on s390 like this one:
net/ipv4/af_inet.c: In function 'build_ehash_secret':
net/ipv4/af_inet.c:241:2: warning: value computed is not used [-Wunused-value]
To get rid of these warnings use the same construct that we already use
for the xchg macro, which was introduced for the same reason.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All cmpxchg functions imply a memory barrier.
cmpxch64 did not have one for 31 bit code, so add it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It has been a big mistage to add the capabilities attribute to the
cpus in sysfs:
First the attribute only contains the cpu capability of primary cpus,
which however is not necessarily (or better: unlikely) the type of
cpu the kernel runs on, which is typically an IFL.
In addition all information that is necessary is available in
/proc/sysinfo already. So this attribute partially duplicated
informations.
So programs should look into the sysinfo file to retrieve all
informations they are interested in.
Since with this kernel release also the powersavings cpu attributes
are removed this seems to be a good opportunity to remove another
broken interface.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the IPL CPU is offline, currently the pcpu_delegate() function
used by smp_call_ipl_cpu() does not work because pcpu_delegate()
modifies the lowcore of the target CPU. In case of an offline
IPL CPU currently the prefix register is zero but pcpu->lowcore
still points to the old prefix page. Therefore the lowcore changes
done by pcpu_delegate() have no effect.
With this fix pcpu_delegate() now uses memcpy_absolute() and therefore
also prepares the absolute zero lowcore if the target CPU has prefix
register zero.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the new function memcpy_absolute() that allows to
copy memory using absolute addressing. This means that the prefix swap
does not apply when this function is used.
With this patch also all s390 kernel code that accesses absolute zero
now uses the new memcpy_absolute() function. The old and less generic
copy_to_absolute_zero() function is removed.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull x86 trampoline rework from H. Peter Anvin:
"This code reworks all the "trampoline"/"realmode" code (various bits
that need to live in the first megabyte of memory, most but not all of
which runs in real mode at some point) in the kernel into a single
object. The main reason for doing this is that it eliminates the last
place in the kernel where we needed pages to be mapped RWX. This code
separates all that code into proper R/RW/RX pages."
Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).
Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.
* commit '61f5446169046c217a5479517edac3a890c3bee7': (36 commits)
x86, realmode: Move end signature into header.S
x86, relocs: When printing an error, say relative or absolute
x86, relocs: More relocations which may end up as absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
xen-acpi-processor: Add missing #include <xen/xen.h>
acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
x86, realmode: Change EFER to a single u64 field
x86, realmode: Move kernel/realmode.c to realmode/init.c
x86, realmode: Move not-common bits out of trampoline_common.S
x86, realmode: Mask out EFER.LMA when saving trampoline EFER
x86, realmode: Fix no cache bits test in reboot_32.S
x86, realmode: Make sure all generated files are listed in targets
x86, realmode: build fix: remove duplicate build
x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
x86, realmode: fixes compilation issue in tboot.c
x86, realmode: move relocs from scripts/ to arch/x86/tools
x86, realmode: header for trampoline code
x86, realmode: flattened rm hierachy
x86, realmode: don't copy real_mode_header
x86, realmode: fix 64-bit wakeup sequence
...
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Pull arm updates from Russell King:
"This contains both some fixes found when trying to get the
Assabet+neponset setup as a replacement firewall with a 3c589 PCMCIA
card, and a bunch of changes from Al to fix up the ARM signal
handling, particularly some of the restart behaviour."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: neponset: make sure neponset_ncr_frob() is exported
ARM: fix out[bwl]()
arm: don't open-code ptrace_report_syscall()
arm: bury unused _TIF_RESTORE_SIGMASK
arm: remove unused restart trampoline
arm: new way of handling ERESTART_RESTARTBLOCK
arm: if we get into work_pending while returning to kernel mode, just go away
arm: don't call try_to_freeze() from do_signal()
arm: if there's no handler we need to restore sigmask, syscall or no syscall
arm: trim _TIF_WORK_MASK, get rid of useless test and branch...
arm: missing checks of __get_user()/__put_user() return values
In order to keep consistency with other rtc drivers,rename CONFIG_RTC_MXC
to CONFIG_RTC_DRV_MXC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
[akpm@linux-foundation.org: fix missed arch/arm/configs/imx_v6_v7_defconfig]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When holding the mmap_sem for reading, pmd_offset_map_lock should only
run on a pmd_t that has been read atomically from the pmdp pointer,
otherwise we may read only half of it leading to this crash.
PID: 11679 TASK: f06e8000 CPU: 3 COMMAND: "do_race_2_panic"
#0 [f06a9dd8] crash_kexec at c049b5ec
#1 [f06a9e2c] oops_end at c083d1c2
#2 [f06a9e40] no_context at c0433ded
#3 [f06a9e64] bad_area_nosemaphore at c043401a
#4 [f06a9e6c] __do_page_fault at c0434493
#5 [f06a9eec] do_page_fault at c083eb45
#6 [f06a9f04] error_code (via page_fault) at c083c5d5
EAX: 01fb470c EBX: fff35000 ECX: 00000003 EDX: 00000100 EBP:
00000000
DS: 007b ESI: 9e201000 ES: 007b EDI: 01fb4700 GS: 00e0
CS: 0060 EIP: c083bc14 ERR: ffffffff EFLAGS: 00010246
#7 [f06a9f38] _spin_lock at c083bc14
#8 [f06a9f44] sys_mincore at c0507b7d
#9 [f06a9fb0] system_call at c083becd
start len
EAX: ffffffda EBX: 9e200000 ECX: 00001000 EDX: 6228537f
DS: 007b ESI: 00000000 ES: 007b EDI: 003d0f00
SS: 007b ESP: 62285354 EBP: 62285388 GS: 0033
CS: 0073 EIP: 00291416 ERR: 000000da EFLAGS: 00000286
This should be a longstanding bug affecting x86 32bit PAE without THP.
Only archs with 64bit large pmd_t and 32bit unsigned long should be
affected.
With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad()
would partly hide the bug when the pmd transition from none to stable,
by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is
enabled a new set of problem arises by the fact could then transition
freely in any of the none, pmd_trans_huge or pmd_trans_stable states.
So making the barrier in pmd_none_or_trans_huge_or_clear_bad()
unconditional isn't good idea and it would be a flakey solution.
This should be fully fixed by introducing a pmd_read_atomic that reads
the pmd in order with THP disabled, or by reading the pmd atomically
with cmpxchg8b with THP enabled.
Luckily this new race condition only triggers in the places that must
already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix
is localized there but this bug is not related to THP.
NOTE: this can trigger on x86 32bit systems with PAE enabled with more
than 4G of ram, otherwise the high part of the pmd will never risk to be
truncated because it would be zero at all times, in turn so hiding the
SMP race.
This bug was discovered and fully debugged by Ulrich, quote:
----
[..]
pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and
eax.
496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t
*pmd)
497 {
498 /* depend on compiler for an atomic pmd read */
499 pmd_t pmdval = *pmd;
// edi = pmd pointer
0xc0507a74 <sys_mincore+548>: mov 0x8(%esp),%edi
...
// edx = PTE page table high address
0xc0507a84 <sys_mincore+564>: mov 0x4(%edi),%edx
...
// eax = PTE page table low address
0xc0507a8e <sys_mincore+574>: mov (%edi),%eax
[..]
Please note that the PMD is not read atomically. These are two "mov"
instructions where the high order bits of the PMD entry are fetched
first. Hence, the above machine code is prone to the following race.
- The PMD entry {high|low} is 0x0000000000000000.
The "mov" at 0xc0507a84 loads 0x00000000 into edx.
- A page fault (on another CPU) sneaks in between the two "mov"
instructions and instantiates the PMD.
- The PMD entry {high|low} is now 0x00000003fda38067.
The "mov" at 0xc0507a8e loads 0xfda38067 into eax.
----
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell <sfr@canb.auug.org.au> reported following error:
In file included from arch/sparc/kernel/prom_common.c:26:0:
arch/sparc/include/asm/leon.h:221:9: error: unknown type name 'irq_flow_handler_t'
arch/sparc/include/asm/leon.h:224:10: error: unknown type name 'irq_flow_handler_t'
Fix this by:
1) Avoid including leon.h in prom_commen.h (not needed)
2) Include irq.h in leon.h to avoid the missing symbol error
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
head_32.S failed to set cputypval for leon, causing boot to fail.
The boot failed because we failed to recognize this was a LEON
cpu so we did not preoperly run-time patch the the kernel.
This resulted in an early crash.
Reported-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Konrad Eisele <konrad@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
This fixes a build failure with CONFIG_CACHE_L2X0=n:
arch/arm/mach-imx/built-in.o: In function `imx3_init_l2x0':
imx53-dt.c:(.init.text+0x190): undefined reference to `l2x0_init'
make[2]: *** [.tmp_vmlinux1] Error 1
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
When the l2 cache isn't enabled the quirk introduced in
9524705 (MX35: Fix bogus L2 cache settings) doesn't need to be done
either.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The first argument of I2C_BOARD_INFO is used to assign .type, so drop
second assignment.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 5fb86e5 (ARM: mx31_3ds: Add sound support) missed to select IMX_HAVE_PLATFORM_IMX_SSI,
which causes the following build error when only mx31_3ds is selected:
arch/arm/mach-imx/built-in.o: In function `mx31_3ds_init':
mach-mx31_3ds.c:(.init.text+0x15dc): undefined reference to `imx_add_imx_ssi'
mach-mx31_3ds.c:(.init.text+0x16b8): undefined reference to `imx31_imx_ssi_data'
Select IMX_HAVE_PLATFORM_IMX_SSI to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Pull kbuild updates from Michal Marek.
Fixed up nontrivial merge conflict in Makefile as per Stephen Rothwell
and linux-next (and trivial arch/sparc/Makefile changes due to removed
sparc32 logic).
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
mips: Fix KBUILD_CPPFLAGS definition
kbuild: fix ia64 link
kbuild: document KBUILD_LDS, KBUILD_VMLINUX_{INIT,MAIN} and LDFLAGS_vmlinux
kbuild: link of vmlinux moved to a script
kbuild: refactor final link of sparc32
kbuild: drop unused KBUILD_VMLINUX_OBJS from top-level Makefile
kbuild: Makefile: remove unnecessary check for m68knommu ARCH
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oLXf
-----END PGP SIGNATURE-----
Merge tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Pull microblaze changes from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Setup correct pointer to TLS area
microblaze: Add TLS support to sys_clone
microblaze: ftrace: Pass the first calling instruction for dynamic ftrace
microblaze: Port OOM changes to do_page_fault
microblaze: Do not select GENERIC_GPIO by default
The huge page size is 4M on non-PAE host, but 2M page size is used in
transparent_hugepage_adjust(), so the page we get after adjust the
mapping level is not the head page, the BUG_ON() will be triggered
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
No need for two implementations - we check the cpu model.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Unconditially define pci32_dma_ops as this is used
for leon.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
With the removal of sun4c we can use the same cpu_idle()
implementation on UP and SMP.
This also fix it so we use the same version independent on LEON
enabled or not.
V2: Fixed whitespace issue pointed out by Josip Rodin.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Josip Rodin <joy@entuzijast.net>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
All users of MMUREGS ASI is now LEON/SUN aware,
so this is no longer required.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
LEON uses a different ASI than SUN for MMUREGS
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
All users of MMUREGS ASI in kernel/ now uses run-time patching.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Fix following warning:
WARNING: arch/sparc/kernel/built-in.o(.cpuinit.text+0x9f4): Section mismatch in reference from the function leon_callin() to the function .init.text:leon_configure_cache_smp()
The function __cpuinit leon_callin() references
a function __init leon_configure_cache_smp().
If leon_configure_cache_smp is only used by leon_callin then
annotate leon_configure_cache_smp with a matching annotation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Fix-up leon specific assembler to use ASI_LEON_MMUREGS
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
- Drop unused stuff accumulated over time
- Drop non-leon stuff
- Include almost all of the header unconditionally
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
A few hardcoded constant were replaced by symbolic
versions to improve readability
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
This will be used to handle that MMUREGS has different ASI for SUN and LEON.
This is the infrastructure only - users will come later.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
We use the compatibility property to determine the
sun models. For leon we use psr.impl and ignore the
result of the getprops call.
Include a hack to allow build as the support code
is not yet converted.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
Use PSR to check if the CPU is LEON and jump to
LEON specific code in this case.
Added a few constants to psr.h to increase readability.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Konrad Eisele <konrad@gaisler.com>
A few strings have been adopted to show more relevant info.
Julian Calaby <julian.calaby@gmail.com> pointed out one
that I would otherwise have missed.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes this sparc32 defconfig build error:
timekeeping.c:(.text+0x277c4): undefined reference to `arch_gettimeoffset'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in Linus's tree to get the commits that blew away
ARCH_USES_GETTIMEOFFSET but didn't update Sparc correctly, so
that I can apply Stephen Rothwell's fix for that mis-merge.
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic version is both easier to support and more correct.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is much the same as for SPARC except that we can do the find_zero()
function more efficiently using the count-leading-zeroes instructions.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I8Se
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next
Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
This makes <asm/word-at-a-time.h> actually live up to its promise of
allowing architectures to help tune the string functions that do their
work a word at a time.
David had already taken the x86 strncpy_from_user() function, modified
it to work on sparc, and then done the extra work to make it generically
useful. This then expands on that work by making x86 use that generic
version, completing the circle.
But more importantly, it fixes up the word-at-a-time interfaces so that
it's now easy to also support things like strnlen_user(), and pretty
much most random string functions.
David reports that it all works fine on sparc, and Jonas Bonn reported
that an earlier version of this worked on OpenRISC too. It's pretty
easy for architectures to add support for this and just replace their
private versions with the generic code.
* generic-string-functions:
sparc: use the new generic strnlen_user() function
x86: use the new generic strnlen_user() function
lib: add generic strnlen_user() function
word-at-a-time: make the interfaces truly generic
x86: use generic strncpy_from_user routine
A few device tree updates and an include file fix for versatile.
* 'vexpress-v3.4' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
+ update to 3.4
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf5c: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuevXAAoJEIwa5zzehBx3D8YQAKfoY3TFjJ9KmJgk69/pc7cf
Of0rvX+35NezGFljIyRdspz+DsV+vhJravwdVxOagRKvVBOb9qnZIXnl3gkLnTw4
dCVMFMqCwXhBeXlXCzHSeRmt2+4/fmJnr7jr4xh9omOAJ9BZv5ftmKNW4zP5wr1L
+9HBwzkxlVisR4NCz2q66YBjsV2dXA3dv2hZxEFkUdQFYJGqZoUXLYHF9yno20i3
knKNXEyAFYFUKHiFVBQJ1tYGmZlaIjw14g+GTqzZay2Pi/HjUXfrPd0VwNkBzZf/
H1N3/cf4GJ2+K/zYqh+H/Xjf/Fjkp1dFNhlUQ7+l5Jwbu7C1B2euvwTO4OaqrfdD
7eqG3+uIKhPO2Z8ZySLFgx4ghybtwgZrAwOjsa+ymTugqPbiWYB/zZR1iWu5DMk/
TnNb6P3ciP+WMpoMFh1kXRc/eCCCHtuQ0rLRxizSX6HIpxWvjYFNLH7L3wS+KtlB
7vsS764d1JFW318bsdBi+V/LWRVXeSWWetTzdzDcM/Syz3ZqfPy7e3Ge6qx0lvYe
5ojgzKwVqpJenZdt91UC16cMXNqDTzmZObz6LOCmVm1mB5kYSgEHYxAQQvuGFjXT
28kGyBQNsBboJGaYh2O/CTsVXnHnaPXrtDDWMDacWNwwPYnnA2L8lUNfAg1DgA1j
Z6CO8Knfct01EpQLtybK
=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
For the first time, we have one branch that collects just updates to
defconfig files, mostly for adapting to changes in other subsystems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pvPg
-----END PGP SIGNATURE-----
Merge tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc defconfig updates from Olof Johansson:
"For the first time, we have one branch that collects just updates to
defconfig files, mostly for adapting to changes in other subsystems."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: add prima2_defconfig for CSR SiRFprimaII
ARM: tegra: update defconfig
ARM: tegra: update defconfig
ARM: imx_v6_v7_defconfig: Add SPI NOR support
ARM: imx_v4_v5_defconfig: Let CONFIG_MACH_IMX27_DT be built by default
Now that all drivers are converted to OF we are able to remove some remaining
pieces of orphaned code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This throws away the old x86-specific functions in favor of the generic
optimized version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes the interfaces in <asm/word-at-a-time.h> to be a bit more
complicated, but a lot more generic.
In particular, it allows us to really do the operations efficiently on
both little-endian and big-endian machines, pretty much regardless of
machine details. For example, if you can rely on a fast population
count instruction on your architecture, this will allow you to make your
optimized <asm/word-at-a-time.h> file with that.
NOTE! The "generic" version in include/asm-generic/word-at-a-time.h is
not truly generic, it actually only works on big-endian. Why? Because
on little-endian the generic algorithms are wasteful, since you can
inevitably do better. The x86 implementation is an example of that.
(The only truly non-generic part of the asm-generic implementation is
the "find_zero()" function, and you could make a little-endian version
of it. And if the Kbuild infrastructure allowed us to pick a particular
header file, that would be lovely)
The <asm/word-at-a-time.h> functions are as follows:
- WORD_AT_A_TIME_CONSTANTS: specific constants that the algorithm
uses.
- has_zero(): take a word, and determine if it has a zero byte in it.
It gets the word, the pointer to the constant pool, and a pointer to
an intermediate "data" field it can set.
This is the "quick-and-dirty" zero tester: it's what is run inside
the hot loops.
- "prep_zero_mask()": take the word, the data that has_zero() produced,
and the constant pool, and generate an *exact* mask of which byte had
the first zero. This is run directly *outside* the loop, and allows
the "has_zero()" function to answer the "is there a zero byte"
question without necessarily getting exactly *which* byte is the
first one to contain a zero.
If you do multiple byte lookups concurrently (eg "hash_name()", which
looks for both NUL and '/' bytes), after you've done the prep_zero_mask()
phase, the result of those can be or'ed together to get the "either
or" case.
- The result from "prep_zero_mask()" can then be fed into "find_zero()"
(to find the byte offset of the first byte that was zero) or into
"zero_bytemask()" (to find the bytemask of the bytes preceding the
zero byte).
The existence of zero_bytemask() is optional, and is not necessary
for the normal string routines. But dentry name hashing needs it, so
if you enable DENTRY_WORD_AT_A_TIME you need to expose it.
This changes the generic strncpy_from_user() function and the dentry
hashing functions to use these modified word-at-a-time interfaces. This
gets us back to the optimized state of the x86 strncpy that we lost in
the previous commit when moving over to the generic version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic strncpy_from_user() is not really optimal, since it is
designed to work on both little-endian and big-endian. And on
little-endian you can simplify much of the logic to find the first zero
byte, since little-endian arithmetic doesn't have to worry about the
carry bit propagating into earlier bytes (only later bytes, which we
don't care about).
But I have patches to make the generic routines use the architecture-
specific <asm/word-at-a-time.h> infrastructure, so that we can regain
the little-endian optimizations. But before we do that, switch over to
the generic routines to make the patches each do just one well-defined
thing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPv7OiAAoJEKurIx+X31iBQxEP/RV8YO4nrozhHY597qabzfJc
4YoCOma+wUyhXPDmZI80XvrIlcCq7TEJL1HTaAyA5rnyYvRHpM+uXDCRmbJDI4e0
gA42/Y8+lbmR6BLY8sdptCXIWxw/d8wYEKK2BgNsPhkJxODGW/gVAws93erist/v
yepq+GwI0QGAeRlO6AYgE7NwQmHXK5AdfH3phHUTVABVIUGH5+Zp6471FTB+hYy5
aNvUnL0hw8vxrbpDL/Le359etPqC6wsELCIQ9wVtWCD0/UJM6Yd3j0+CKQ7q/KHU
7zMcP+OCGTJ3koMhEbFIOnxuswWDGq5y/qIzSXMEEemGqgxqFUvX3wUeZ3HFAFNx
nJ7ZaA813t7Bud4G4WwESxMGQpxI7FTvxnF1ow3IlRsMtV4ffvAS9xvWi0GQJrVY
xixK7G87PGAm6fP9Zbb/lQlRO8gD498j4rfI9MOsUuY9QgFNcH2eg6c4O0iHDpos
WkSgUaM49Q610JslrxsXp+BZZLBF/wbcjcFiQGFAWOIKTKgRQ99+dXAQY7fw9CIf
/wNl9MkbOvJdPL9OfLTmAYAMXyaXbOX8qcvItwqcBsUT0AV863NdIXtS4BXBOrMs
5u16CDX1ieFAlA2dzhynvE0Zd1Ws6wfe5W/BgtQ+H175uHFr8pHAxsBTX8GSNrXG
/bSWWrR3CIBRHoWCJMmH
=kG4e
-----END PGP SIGNATURE-----
Merge tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull x86/mce merge window patches from Tony Luck:
"Including two that make error_context() checks less sucky"
* tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Add instruction recovery signatures to mce-severity table
x86/mce: Fix check for processor context when machine check was taken.
MCE: Fix vm86 handling for 32bit mce handler
x86/mce Add validation check before GHES error is recorded
x86/mce: Avoid reading every machine check bank register twice.
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
Remove multiple unused cpu_is_omap35xx macros.
In particular, the cpu_is_omap35* macros for 3503, 3515, 3525 are removed
because they are using omap_has_* feature checks and we want to
remove specific feature detection from SoC family detection.
There are no longer any cpu_is_* checks that depend on specific IP
detection.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use the more generic SoC family soc_is_am35xx() instead of the specific
cpu_is_omap3517() (which is being removed.)
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no "ARCH=tile" (just like there is no "ARCH=x86") so we need
to pick a default configuration, either tilepro or tilegx, when users
specify ARCH=tile. We'll use tilegx, since that's our current chip.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Also create a TILEPRO config setting to use for #ifdefs where it
is cleaner to do so, and make the 64BIT setting depend directly
on the setting of TILEGX.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to tile.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
[cmetcalf@tilera.com: initialize "flags" after "write" updated.]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If the kernel unexpectedly takes a bad trap, it's convenient to
have it report the type of trap as part of the error. This gives
customers a bit more context before they call up customer support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This just adds a few more attributes to the information Linux
can query from the hypervisor for the /sys/hypervisor/board/ directory,
providing part, serial#, revision#, and description for cpu modules
(as opposed to the board itself, or any mezzanine boards).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Feng Tang
Linus Torvalds
Marek Szyprowski
Sachin Kamat
Wanpeng Li
Qiao Zhou
Martin Pelikan
Don Zickus
Steffen Rumler
Cliff Wickman
Yinghai Lu
Olof Johansson
Rob Herring
Paul Mackerras
Jaccon Bastiaansen
Jordan Justen
Shawn Guo
Fabio Estevam
Chris Metcalf
Arun Sharma
Peter Zijlstra
Kamalesh Babulal
Geert Uytterhoeven
Tomoki Sekiyama
Sebastian Andrzej Siewior
Yasuaki Ishimatsu
Xiaotian Feng
Thomas Gleixner
Tony Lindgren
Masami Hiramatsu
Chen Gong
Tomi Valkeinen
Govindraj.R
Haojian Zhuang
Javier Martin
James Bottomley
Zhang Rui
Al Viro
Sascha Hauer
Anton Blanchard
H. Peter Anvin
H.J. Lu
David Howells
Matt Fleming
Steven Rostedt
Cyrill Gorcunov
Anton Vorontsov
Kautuk Consul
Lee Jones
Andre Przywara
Mathias Krause
Roland Stigge
Konrad Rzeszutek Wilk
zhenzhong.duan
H. Peter Anvin
Konrad Rzeszutek Wilk
Ingo Molnar
Peter Zijlstra
John Dykstra
Heiko Carstens
Michael Holzheu
Fabio Estevam
Andrea Arcangeli
Bjorn Helgaas
Cong Wang
Russell King
Sam Ravnborg
Uwe Kleine-König
Xiao Guangrong
David S. Miller
Stephen Rothwell
Jonas Bonn
Paul Mundt
Florian Tobias Schandinat
Ralf Baechle
John Crispin
Kevin Hilman