Standard v4l2 userspace apps do not consume the s3a statistics block
data. Until we have a userspace consumer for this (libcamera), which
might also involve changing the API for this, lower the log level
of these messages to dev_dbg() to avoid them filling up the logs.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Depending on which order userspace makes various v4l2 calls, the sensor
might still be powered down when set_fmt is called.
What should really happen here is delay the writing of the mode-related
registers till streaming is started, but for now use the same quick fix
as the atomisp_ov2680 code and call power_up() from set_fmt() in
combination with keeping track of the power-state to avoid doing the
power-up sequence twice.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the complicated __atomisp_get_pipe() helper, atomisp_buf_done()
only needs the pipe pointer in cases where it has a frame, so we can
simply get the pipe from the frame using the vb_to_pipe() helper.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make atomisp_g_fmt_cap() default to YUV420 so that it matches with what
atomisp_try_fmt_cap() and atomisp_queue_setup() do when they need to
pick a default pixelformat.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The atomisp_try_fmt() call in atomisp_try_fmt_cap() replaces
the pixelformat passed by userspace with the sensors native pixelformat.
Which always gets replaced by V4L2_PIX_FMT_YUV420 by atomisp_adjust_fmt()
because raw sensor formats are not supported.
This needs to be fixed so that userspace which does a try_fmt call before
s_fmt does not end up always getting YUV420 even if it passed something
else into the try_fmt call.
To fix this restore the userspace requested pixelformat before
the atomisp_adjust_fmt() call. atomisp_adjust_fmt() will replace this
with V4L2_PIX_FMT_YUV420 in case an unsupported format is requested.
Note this relies on the "media: atomisp: Refactor atomisp_adjust_fmt()"
change, before that atomisp_adjust_fmt() would return -EINVAL for
unsupported pixelformats.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Refactor atomisp_adjust_fmt():
1. The block starting at "format_bridge = atomisp_get_format_bridge(...)"
and ending with "if (field == V4L2_FIELD_ANY) field = V4L2_FIELD_NONE;"
is duplicated. With only the second block:
a) Properly checking that format_bridge is not NULL; amd
b) Having the special handling for IA_CSS_FRAME_FORMAT_RAW
Remove the first block.
2. On a NULL return from atomisp_get_format_bridge(f->fmt.pix.pixelformat)
fall back to V4L2_PIX_FMT_YUV420 just like in the IA_CSS_FRAME_FORMAT_RAW
case. atomisp_adjust_fmt() is used in VIDIOC_TRY_FMT handling and that
should jusy pick a fmt rather then returning -EINVAL.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
camorama calls VIDIOC_REQBUFS(V4L2_MEMORY_MMAP) to test if MMAP support
works (this was added specifically because of the previously broken
MMAP support in atomisp).
Currently this fails because atomisp_get_css_frame_info() fails in this
case. Although it is weird to call VIDIOC_REQBUFS before VIDIOC_S_FMT,
it is allowed to do this.
Fix this not working by doing a S_FMT to V4L2_PIX_FMT_YUV420 + the highest
supported resolution.
Note this will cause camorama to use mmap mode, which means it will also
use libv4l2 to do format conversion. libv4l2 will pick V4L2_PIX_FMT_RGB565
as input format and this will lead to a garbled video display. This is
a libv4lconvert bug, the RGB565 -> RGB24 path in libv4lconvert assumes
that stride == width which is not true on the atomisp.
I've already send out a libv4lconvert fix for this. Also this can be worked
around by passing --dont-use-libv4l2 as argument to camorama.
Link: https://git.linuxtv.org/v4l-utils.git/commit/?id=aecfcfccfc2f78d7531456ffa5465666c6bc641e
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To fix atomisp_queue_setup() sometimes failing it needs to be able to call
atomisp_set_fmt(), but atomisp_queue_setup() (VIDIOC_REQBUFS) does not get
passed a file handle by the videobuf2 core.
Partly revert commit b3be98f984d4 ("media: atomisp: Remove a couple of not
useful function wrappers") so that atomisp_set_fmt() can be used
without a file handle.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert atomisp to use videobuf2.
This fixes mmap not working and in general moving over to
the more modern videobuf2 is a good plan.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Several places rely on the [frame_]info member being the first member of
struct ia_css_frame, so that &frame->info will yield NULL when frame is
NULL (some places already explicitly check for a NULL frame pointer but
not nearly all).
For videobuf2 support the vb2_v4l2_buffer struct needs to be embedded
in the frame struct and it needs to be the first member. Breaking the
assumption that &frame->info will yield NULL when frame is NULL.
Add a ia_css_frame_get_info() helper to return either the ia_css_frame_info
struct embedded in the frame, or NULL when the frame pointer is NULL and
use this in places where a ia_css_frame_info ptr or NULL is expected.
To make sure that we catch all uses of the info field this patch also
renames the info field to frame_info.
This is a preparation patch for converting the driver to videobuf2.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new atomisp_flush_video_pipe() helper instead of open-coding it.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With the videobuf2 conversion accessing the index of a frame is going
to become more involved and writing this out each time is undesired.
Add an 'i' helper variable for the index and assing this once as
preparation for the videobuf2 conversion.
This also makes use of the new rules wrt max line-lengths in the kernel
to avoid breaking up a bunch of lines. Not breaking these lines results
in better readable code (IMHO).
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of using an integer to keep count of how many buffers have
been handed over to the ISP (buffers_in_css) move buffers handed
over to the ISP to a new buffers_in_css list_head so that we can
easily loop over them.
This removes the need for atomisp_flush_video_pipe() to loop over
all buffers and then (ab)use the state to figure out if they
were handed over to the ISP.
Since the buffers are now always on a list when owned by the driver
this also allows the buffer_done path on flush vs normal completion
to be unified (both now need a list_del()) and this common code can
now be factored out into a new atomisp_buffer_done() helper.
This is a preparation patch for moving the driver over to
the videobuf2 framework.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The atomisp_buffers_queued[_pipe] functions are not used anywhere,
remove them.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no guarantee that when we stop the pipeline all buffers owned
by the CSS are cleanly returned to the videobuf queue.
This is a problem with videobuf2 which will complain loudly when not
all buffers have been returned after the streamoff() queue op has
returned.
And this also allows removing a WARN() in the continuous mode path.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
atomisp_q_video_buffers_to_css() is only used insidd atomisp_fops.c, make
it static.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a function to initialize (rather then alloc/create) a
ia_css_frame struct based on an ia_css_frame_info struct.
This is a preparation patch for adding videobuf2 support.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new hmm creating function to create a vmm object from a vmalloc-ed
kernel buffer. This is a preparation patch for adding videobuf2 (and
working MMAP mode) support.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
Link: https://syzkaller.appspot.com/bug?id=e378e6a51fbe6c5cc43e34f131cc9a315ef0337e
Fixes: 21677cfc56 ("V4L/DVB: ir-core: add imon driver")
Reported-by: syzbot+0c3cb6dc05fbbdc3ad66@syzkaller.appspotmail.com
Signed-off-by: Gautam Menghani <gautammenghani201@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
SPI devices use the spi_device_id for module autoloading even on
systems using device tree, after commit 5fa6863ba6 ("spi: Check
we have a spi_device_id for each DT compatible"), kernel warns as
follows since the spi_device_id is missing:
SPI driver ir-spi has no spi_device_id for ir-spi-led
Add spi_device_id entries to silence the warning, and ensure driver
module autoloading works.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRSrcquik9wuZrNjXJrQl33mxwedgUCY3toaQAKCRBrQl33mxwe
dpoQAP4r5trvhHqB/9BLDYn+AwnXOewgywAoD8zBPntAL/WuBwD9HGmnwpJhGdXU
ImIEVNqjGmH9gLJjqNHPm4t4YvxgBAg=
=ZV3Y
-----END PGP SIGNATURE-----
Merge tag 'br-v6.2g' of git://linuxtv.org/hverkuil/media_tree into media_stage
Despite being big, the changes here are trivial: they just change the
probing method for I2C. So, apply it as a merge.
Tag branch
* tag 'br-v6.2g' of git://linuxtv.org/hverkuil/media_tree: (96 commits)
media: v4l2-core/tuner-core: Convert to i2c's .probe_new()
media: usb: go7007: s2250-board: Convert to i2c's .probe_new()
media: tuners/tua9001: Convert to i2c's .probe_new()
media: tuners/tda18250: Convert to i2c's .probe_new()
media: tuners/tda18212: Convert to i2c's .probe_new()
media: tuners/qm1d1c0042: Convert to i2c's .probe_new()
media: tuners/qm1d1b0004: Convert to i2c's .probe_new()
media: tuners/mxl301rf: Convert to i2c's .probe_new()
media: tuners/mt2060: Convert to i2c's .probe_new()
media: tuners/m88rs6000t: Convert to i2c's .probe_new()
media: tuners/fc2580: Convert to i2c's .probe_new()
media: tuners/e4000: Convert to i2c's .probe_new()
media: vidtv: Convert to i2c's .probe_new()
media: radio/tef6862: Convert to i2c's .probe_new()
media: radio/saa7706h: Convert to i2c's .probe_new()
media: radio/radio-tea5764: Convert to i2c's .probe_new()
media: i2c/wm8775: Convert to i2c's .probe_new()
media: i2c/wm8739: Convert to i2c's .probe_new()
media: i2c/vs6624: Convert to i2c's .probe_new()
media: i2c/vpx3220: Convert to i2c's .probe_new()
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Atmel ISC driver is not compliant with media controller specification.
In order to evolve this driver, it has to move to media controller, to
support enhanced features and future products which embed it.
The move to media controller involves several changes which are
not backwards compatible with the current usability of the driver.
The best example is the way the format is propagated from the top video
driver /dev/videoX down to the sensor.
In a simple configuration sensor ==> isc , the isc just calls subdev s_fmt
and controls the sensor directly. This is achieved by having a lot of code
inside the driver that will query the subdev at probe time and make a list
of formats which are usable.
Basically the user has nothing to configure, as the isc will handle
everything at the top level. This is an easy way to capture, but also comes
with the drawback of lack of flexibility.
In a more complicated pipeline
sensor ==> controller 1 ==> controller 2 ==> isc
this will not be achievable, as controller 1 and controller 2 might be
media-controller configurable, and will not propagate the formats down to
the sensor.
After discussions with the media maintainers, the decision is to move
Atmel ISC to staging as-is, to keep the Kconfig symbols and the users
to the driver in staging. Thus, all the existing users of the non
media-controller paradigm will continue to be happy and use the old config
way.
The new driver was added in the media subsystem with a different
symbol, with the conversion to media controller done, and new users
of the driver will be able to use all the new features.
This patch is merely a file move to staging, not affecting any of the
users.
The exported symbols had to be renamed to atmel_* to avoid duplication with
the new Microchip ISC driver.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the media_pipeline_start/stop calls from start/stop streaming to
the new prepare_streaming and unprepare_streaming callbacks.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As a top MC video driver, the microchip-isc should not propagate the format
to the subdevice, it should rather check at start_streaming() time if the
subdev is properly configured with a compatible format.
Removed the whole format finding logic, and reworked the format
verification at start_streaming time, such that the ISC will return an
error if the subdevice is not properly configured.
To achieve this, media_pipeline_start is called and a link_validate
callback is created to check the formats.
With this being done, the module parameter 'sensor_preferred' makes no
sense anymore. The ISC should not decide which format the sensor is using.
The ISC should only cope with the situation and inform userspace if the
streaming is possible in the current configuration.
The redesign of the format propagation has also risen the question of the
enumfmt callback. If enumfmt is called with an mbus_code, the enumfmt
handler should only return the formats that are supported for this
mbus_code. Otherwise, the enumfmt will report all the formats that the ISC
could output.
With this rework, the dynamic list of user formats is removed. It makes no
more sense to identify at complete time which formats the sensor could
emit, and add those into a separate dynamic list.
The ISC will start with a simple preconfigured default format, and at
link validate time, decide whether it can use the format that is
configured on the sink or not.
>From now on, the driver also advertises the IO_MC capability.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Prepare the support for media-controller.
This means that the capabilities of the driver have changed and now it's
capable of media controller operations.
The driver will register its media device, and add the video entity to this
media device. The subdevices are registered to the same media device.
The ISC will have a base entity which is auto-detected as
microchip_isc_base.
It will also register a subdevice that allows cropping of the incoming
frame to the maximum frame size supported by the ISC.
The ISC will create a link between the subdevice that is asynchronously
registered and the microchip_isc_scaler entity.
Then, the microchip_isc_scaler and microchip_isc_base are connected
through another link.
This patch does not change the previous capability of the driver, the
fact that the format is still being propagated from the top video node
down to the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Atmel ISC driver will be moved to staging to support old users that
are not using the media controller paradigm.
The ISC driver was converted to media controller in the public patch
series:
https://lore.kernel.org/lkml/20220503095127.48710-1-eugen.hristev@microchip.com/T/#m2c320fa8153c01379a1c35b1d90a00903949513a
However the conversion cannot be done directly as it would affect existing
users by breaking the old way of configuration for sama5d2 platforms.
After discussions with the media maintainers, the decision is to move
Atmel ISC to staging as-is, to keep the Kconfig symbols and the users
to the driver in staging. Thus, all the existing users of the non
media-controller paradigm will continue to be happy and use the old config
way.
The converted driver would support both sama5d2 and sama7g5 platforms with
media controller paradigm, but it requires userspace configuration of the
pipeline for all the pipeline modules.
In a simple configuration sensor ==> isc , the old isc driver used to call
subdev s_fmt and control the sensor directly.
This was achieved by having a lot of code inside the driver that was
querying the subdev at probe time and made a list of formats which are
usable.
Basically the user had nothing to configure, as the isc would handle
everything at the top level. This was an easy way to capture, but also came
with the drawback of lack of flexibility.
In a more complicated pipeline
sensor ==> controller 1 ==> controller 2 ==> isc
this would not be achievable, as controller 1 and controller 2 might be
media-controller configurable, and will not propagate the formats down to
the sensor.
The new driver Microchip ISC would solve all these problems and exposes pads
entities and links to userspace.
For the ease of tracking, the patches that convert to media controller come
on top of this patch that simply readds the driver to the new location under
the new Kconfig symbols.
To differentiate between the old driver and the new driver, I have renamed
the new driver to Microchip ISC, renaming the Kconfig symbols as well, and
all the mentions inside the driver.
The only thing that remains common is the file
include/linux/atmel-isc-media.h which is the ABI for the v4l2 custom
controls that the ISC exposes.
This file is used by both driver, so I kept it as-is.
To further avoid confusion all files have been renamed and all functions
named isc_* as well.
The exported symbols have been renamed with added microchip_ prefix, to
avoid symbol duplication with the old driver, and to avoid confusion.
Other than that, I have fixed small checkpatch issues when readding the
driver.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Atmel ISC will be moved to staging thus the atmel platform will only
have the ISI driver.
The new media-controller converted ISC driver will be placed inside a
dedicated microchip platform directory.
It is then natural to have the microchip-csi2dc moved to this new platform
directory.
The next step is to add the Microchip ISC driver to the new platform
directory and reside together with the Microchip CSI2DC driver.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With the new prepare_streaming op it is possible to move the ugly
v4l_vb2q_enable_media_source() call in vb2_core_streamon to the
driver. It was called incorrectly in vb2 as well: it was only
called if sufficient buffers were queued at STREAMON time, but not
if more buffers were queued later. This was not an issue with the
au0828 driver since it never set min_buffers_needed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When userspace called VIDIOC_STREAMON, then you want to claim any streaming
resources needed and validate the video pipeline. Waiting for
start_streaming to be called is too late, since that can be postponed
until the required minimum of buffers is queued.
So add a prepare_streaming op (optional) that can be used for that
purpose, and a matching unprepare_streaming op (optional) that can
release any claimed resources. The unprepare_streaming op is called
when VIDIOC_STREAMOFF is called and q->streaming is 1, or when the
filehandle is closed while q->streaming is 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document administration details about CEC devices. This was formerly
documented in a cec-status.txt I kept on my website, but this really
belongs here as an admin guide.
Updated the original cec-status.txt, and converted it to .rst.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This cleans up a checkstyle warning where the vb2_ops struct definitions
should be const.
Signed-off-by: Ian Cowan <ian@linux.cowan.aero>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A problem about modprobe amphion-vpu failed is triggered with the
following log given:
[ 2208.634841] Error: Driver 'amphion-vpu' is already registered, aborting...
modprobe: ERROR: could not insert 'amphion_vpu': Device or resource busy
The reason is that vpu_driver_init() returns vpu_core_driver_init()
directly without checking its return value, if vpu_core_driver_init()
failed, it returns without unregister amphion_vpu_driver, resulting the
amphion-vpu can never be installed later.
A simple call graph is shown as below:
vpu_driver_init()
platform_driver_register() # register amphion_vpu_driver
vpu_core_driver_init()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister amphion_vpu_driver
Fix by unregister amphion_vpu_driver when vpu_core_driver_init() returns
error.
Fixes: b50a64fc54 ("media: amphion: add amphion vpu device driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: ming_qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b0 ("[media] s5p-fimc: Add the media device driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
destroy_workqueue() needs be called to when driver is
unloading, fix it by using devm_add_action_or_reset()
to make workqueuedevice-managed.
Fixes: dedc215003 ("media: mtk-jpegdec: add jpeg decode worker interface")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the host is powered off, there will be many warning log. To avoid the
log spam in this condition, replace v4l2_warn with v4l2_dbg.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbc ("[media] solo6x10: sync to latest code from Bluecherry's git repo")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Testing reference video TSUNEQBD_A_MAIN10_Technicolor_2 has show that
Cedrus is capable of decoding frames with different chroma and luma bit
depths.
Relax restrictions so only highest depth is checked.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
10-bit frames needs extra buffer space when 8-bit capture format is
used. Use previously prepared infrastructure to adjust buffer size.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In some cases decoding engine needs extra space in capture buffers. This
is the case for decoding 10-bit HEVC frames into 8-bit capture format.
This commit only adds infrastructure for such cases.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Already error number provision is present for block failing, while
requesting for DMA consistent memory allocation.
So removing error message line from the block as recommended
by scripts/checkpatch.pl.
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
...
dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
platform_probe+0xb6/0x170
...
Allocated by task 1238:
...
dvb_register_device+0x1a7/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
Freed by task 1238:
dvb_register_device+0x6d2/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything.
Fixes: f90cf6079b ("media: vidtv: add a bridge driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use of standard min() helper macro is preferred over using ternary
operator for logical evaluation and value assignment. This issue is
identified by coccicheck using the minmax.cocci file.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A virtual stateless device for stateless uAPI development purposes.
This tool's objective is to help the development and testing of
userspace applications that use the V4L2 stateless API to decode media.
A userspace implementation can use visl to run a decoding loop even when
no hardware is available or when the kernel uAPI for the codec has not
been upstreamed yet. This can reveal bugs at an early stage.
This driver can also trace the contents of the V4L2 controls submitted
to it. It can also dump the contents of the vb2 buffers through a
debugfs interface. This is in many ways similar to the tracing
infrastructure available for other popular encode/decode APIs out there
and can help develop a userspace application by using another (working)
one as a reference.
Note that no actual decoding of video frames is performed by visl. The
V4L2 test pattern generator is used to write various debug information
to the capture buffers instead.
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
vb2_queue_error is help to set the error of vb2_queue,
don't need to set it manually
Fixes: 3cd084519c ("media: amphion: add vpu v4l2 m2m support")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
the capture format may be changed when
sequence header is parsed,
it may be read and write in the same time,
add lock around vdec_g_fmt to synchronize it
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In order to use the isp and csi together, both devices need to be
parented to the same v4l2 and media devices. We use the isp as
top-level device and let the csi code hook to its v4l2 and media
devices when async subdev registration takes place.
As a result v4l2/media device setup is only called when the ISP
is missing and the capture device is registered after the devices
are hooked. The bridge subdev and its notifier are registered
without any device when the ISP is available. Top-level pointers
for the devices are introduced to either redirect to the hooked ones
(isp available) or the registered ones (isp missing).
Also keep track of whether the capture node was setup or not to
avoid cleaning up resources when it wasn't.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a helper to detect whether the ISP is available and connected
and store the indication in the driver-specific device structure.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>