M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When #include'd alone, <linux/usb/gadget.h>
causes a lot of compilation errors and warnings
-- all because it relies on the including code to
bring in the necessary #include's instead of
doing this itself.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used by the Gadget drivers to specify
the maximum speed they support, meaning: the maximum
speed they can provide descriptors for.
The driver speed will be set in consideration of this
value.
[ balbi@ti.com : dropped the ifdeffery ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch defines necessary fields to support
streaming for USB3.0.
It implements a new function, called
usb_ep_autoconfig_ss(), to be used instead of the
existing usb_ep_autoconfig() when working in
SuperSpeed mode and there is a need to search for
an endpoint according to the number of required
streams.
[ balbi@ti.com : slight changes to commit log ]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add config_ep_by_speed() to configure the endpoint
according to the gadget speed.
Using this function will spare the FDs from handling
the endpoint chosen descriptor.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change usb_ep_enable() prototype to use endpoint
descriptor from usb_ep.
This optimization spares the FDs from saving the
endpoint chosen descriptor. This optimization is
not full though. To fully exploit this change, one
needs to update all the UDCs as well since in the
current implementation each of them saves the
endpoint descriptor in it's internal (and extended)
endpoint structure.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this class will be used to abstract away several of the duplicated
operations scattered among the USB gadget controller drivers.
Later, we can add an atomic notifier to tell interested drivers about
what's happening with the controller. Notifications such as suspend,
resume, enumerated, etc. will be useful, at a minimum, for implementing
usb charger detection.
As part of the converting process usb_gadget_probe_driver() is no longer
part of each udc but pushed into the ->stap() callback. The same for his
couterpart.
The core is currently set explicit to 'n'. It will be changed to 'y' once
all users are converted since it provides functions which clash with
other drivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB DMA was installed on "normal DMAC" when SH7724 or older SuperH,
but the "USB-DMAC" was prepared on recent SuperH.
These 2 DMAC have a little bit different behavior.
This patch add DMAEngine code for "normal DMAC",
but it is still using PIO fifo.
The DMA fifo will be formally supported in the future.
You can enable DMA fifo by local fixup
usbhs_fifo_pio_push_handler -> usbhs_fifo_dma_push_handler
usbhs_fifo_pio_pop_handler -> usbhs_fifo_dma_pop_handler
on usbhsg_ep_enable.
This DMAEngine was tested by g_file_storage on SH7724 Ecovec board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports. USB hardware is put into low power
mode when connected to a dedicated charging port. vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).
The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY). The PHY vendor and product id registers are not
implemented in the above chipsets. Hence PHY type is passed via platform
data.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by Arnd Bergmann, in include/linux/usb/ehci_def.h, struct
ehci_caps is defined with __attribute__((packed)) for no good reason,
and this triggers undefined behaviour when using ARM's readl() on
pointers to elements of this structure:
http://lkml.kernel.org/r/201102021700.20683.arnd@arndb.de
The same problem exists with the other two structures in ehci_def.h too,
so remove the __attribute__((packed)) from all of them.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci 1.0: Set transfer burst last packet count field.
xhci 1.0: Set transfer burst count field.
xhci 1.0: Update TD size field format.
xhci 1.0: Only interrupt on short packet for IN EPs.
xhci: Remove sparse warning about cmd_status.
usbcore: warm reset USB3 port in SS.Inactive state
usbcore: Refine USB3.0 device suspend and resume
xHCI: report USB3.0 portstatus comply with USB3.0 specification
xHCI: Set link state support
xHCI: Clear link state change support
xHCI: warm reset support
usb/ch9: use proper endianess for wBytesPerInterval
xhci: Remove recursive call to xhci_handle_event
xhci: Add an assertion to check for virt_dev=0 bug.
xhci: Add rmb() between reading event validity & event data access.
xhci: Make xHCI driver endian-safe
while going through Tatyana's changes for the gadget framework I noticed
that this type is not defined as __le16.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Provide common otg_state_string() and use
it in drivers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This delay is used to overjump debounce.
And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The callback function which is called from platform must be removed
if module removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmit interrupt URB if device is open. Use a flag set in
usbnet_open() to determine this state. Also kill and free
interrupt URB in usbnet_disconnect().
[Rebased off git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB tethering does not work anymore since 2.6.39-rc2, but it's okay in
-rc1. The root cause is the new added mask code 'FLAG_POINTTOPOINT'
overlaps 'FLAG_MULTI_PACKET' in include/linux/usb/usbnet.h, this
causes logic issue in rx_process(). This patch cleans up the overlap.
Reported-and-Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 41 occurrences of this type of Section mismatch warning
in g_mass_storage, g_serial, g_cdc, g_multi, g_nokia, g_ether, g_ffs:
(the 75 number reported earlier contained some duplicates.)
WARNING: drivers/usb/gadget/g_mass_storage.o(.text+0x687a): Section mismatch in reference from the function fsg_bind() to the function .devinit.text:usb_ep_autoconfig()
The function fsg_bind() references
the function __devinit usb_ep_autoconfig().
This is often because fsg_bind lacks a __devinit
annotation or the annotation of usb_ep_autoconfig is wrong.
Also remove __devinit from usb_ep_autoconfig_reset() to prevent
possible section mismatch problems with it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some RNDIS devices don't respond on the control channel until polled
on the status channel. In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW and for some Windows Mobile
devices.
This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is currently applied by Mandriva.
Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.
Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().
Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.
The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two. The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: Andy Green <andy.green@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the CDC Ethernet part of this modem. The
device's ID is blacklisted in cdc_ether.c and is white-listed in
this new driver because of the quirks needed to make it useful.
The modem's firmware exposes a CDC ACM port for modem control and a
CDC Ethernet port for network data. The descriptors look fine but
both ports actually are some sort of multiplexers requiring non-
standard headers added/removed from every packet or they get
ignored. All information is based on a usb traffic log from a
Windows machine.
On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with
this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps.
Userspace scripts are required to talk to the CDC ACM port.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
Use the Mult and bMaxBurst values from the endpoint companion
descriptor to calculate the max length of an isoc transfer.
Add USB_SS_MULT macro to access Mult field of bmAttributes, at
Sarah's suggestion.
This patch should be queued for the 2.6.36 and 2.6.37 stable trees, since
those were the first kernels to have isochronous support for SuperSpeed
devices.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
USB_PORT_STAT_SUPER_SPEED is a made up symbol that the USB core used to
track whether USB ports had a SuperSpeed device attached. This is a
linux-internal symbol that was used when SuperSpeed and non-SuperSpeed
devices would show up under the same xHCI roothub. This particular
port status is never returned by external USB 3.0 hubs. (Instead they
have a USB_PORT_STAT_SPEED_5GBPS that uses a completely different speed
mask.)
Now that the xHCI driver registers two roothubs, USB 3.0 devices will only
show up under USB 3.0 hubs. Rip out USB_PORT_STAT_SUPER_SPEED and replace
it with calls to hub_is_superspeed().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Introduce the notion of a PCI device that may be associated with more than
one USB host controller driver (struct usb_hcd). This patch is the start
of the work to separate the xHCI host controller into two roothubs: a USB
3.0 roothub with SuperSpeed-only ports, and a USB 2.0 roothub with
HS/FS/LS ports.
One usb_hcd structure is designated to be the "primary HCD", and a pointer
is added to the usb_hcd structure to keep track of that. A new function
call, usb_hcd_is_primary_hcd() is added to check whether the USB hcd is
marked as the primary HCD (or if it is not part of a roothub pair). To
allow the USB core and xHCI driver to access either roothub in a pair, a
"shared_hcd" pointer is added to the usb_hcd structure.
Add a new function, usb_create_shared_hcd(), that does roothub allocation
for paired roothubs. It will act just like usb_create_hcd() did if the
primary_hcd pointer argument is NULL. If it is passed a non-NULL
primary_hcd pointer, it sets usb_hcd->shared_hcd and usb_hcd->primary_hcd
fields. It will also skip the bandwidth_mutex allocation, and set the
secondary hcd's bandwidth_mutex pointer to the primary HCD's mutex.
IRQs are only allocated once for the primary roothub.
Introduce a new usb_hcd driver flag that indicates the host controller
driver wants to create two roothubs. If the HCD_SHARED flag is set, then
the USB core PCI probe methods will allocate a second roothub, and make
sure that second roothub gets freed during rmmod and in initialization
error paths.
When usb_hc_died() is called with the primary HCD, make sure that any
roothubs that share that host controller are also marked as being dead.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver essentially has both a USB 2.0 and a USB 3.0 roothub. So
setting the HCD_USB3 bits in the hcd->driver->flags is a bit misleading.
Add a new field to usb_hcd, bcdUSB. Store the result of
hcd->driver->flags & HCD_MASK in it. Later, when we have the xHCI driver
register the two roothubs, we'll set the usb_hcd->bcdUSB field to HCD_USB2
for the USB 2.0 roothub, and HCD_USB3 for the USB 3.0 roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow
the pointer to be shared across usb_hcds for the upcoming work to split
the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman
Yoshihiro Shimoda
Sebastian Andrzej Siewior
Sergei Shtylyov
Tatyana Brokhman
Felipe Balbi
Kuninori Morimoto
Mark Brown
Linus Torvalds
Roger Quadros
Pavankumar Kondeti
Anji jonnala
Anatolij Gustschin
David S. Miller
Jan Andersson
Rabin Vincent
Paul Stewart
huajun li
Randy Dunlap
Ben Hutchings
Arnd Bergmann
Lucas De Marchi
Andrzej Zaborowski
Paul Zimmerman
Sarah Sharp
John Youn
Benoit Goby