The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sunxi_rsb_driver::remove
return void, too. All users already unconditionally return 0, this
commit makes this obvious and ensures future users don't behave
differently. To simplify even further, make axp20x_device_remove()
return void instead of returning 0 unconditionally, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
via RSB bus. The PMIC itself is like AXP288, but with RSB support and
dedicated VBUS and ACIN.
Add support for it in the axp20x mfd driver.
Currently only power key function is supported.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP809 is a new PMIC that is paired with Allwinner's A80
SoC, along with a slave AXP806 PMIC.
This PMIC is quite similar to the earlier AXP223, though the interrupts
and regulator have changed a bit.
This patch adds support for the interrupts and power button of the PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Uwe Kleine-König
Thomas Gleixner
Chen-Yu Tsai
Icenowy Zheng